"Assisted factorial experimental design" per l'ottimizzazione della determinazione di benzene ematico in gc-fid

La quantificazione del benzene ematico è un tema di grande interesse nell'ambito della tossicologia occupazionale. La determinazione dell'analita, estratto nello spazio di testa di un vial, è eseguita mediante l'utilizzo di un gascromatografo con rilevatore a ionizzazione di fiamma (GC-FID). Si è cercato di ottimizzare il processo di estrazione del benzene dal sangue allo spazio di testa ed il successivo trasferimento dell'analita nella colonna cromatografica, mediante l'applicazione di un disegno sperimentale fattoriale a tre fattori e due livelli (DoE). I fattori individuati per impostare il piano sperimentale sono stati: variazione della temperatura di incubazione (A) del vial contenente il campione di sangue, pH del campione (B), modulato mediante aggiunta di una soluzione di H2SO4 e forza ionica (C), regolata mediante una soluzione acquosa di NaCl. I livelli scelti per ciascuna variabile sono stati: per A 40 e 60 °C; per B pH naturale del campione e pH a seguito dell'aggiunta di 1 mL di H2SO4 1.8 M; per C FI naturale del campione e FI dovuta all'aggiunta di una soluzione acquosa di sodio cloruro (5 g/L). Dall'analisi dei risultati forniti dal DoE, si è osservato che A, B e C hanno effetti tra loro contrastanti, per questo motivo non sembra essere vantaggioso combinare variabili differenti. In compenso, sia l'aumento di temperatura che l'aggiunta di acido solforico portano a significativi miglioramenti nell'estrazione di benzene dal sangue. Tra i tre trattamenti risulta essere B quello più efficace, motivo per il quale si ritiene che l'aggiunta di una soluzione acquosa di H2SO4 al campione di sangue porti ad una maggiore sensibilità e risoluzione strumentale. Sicuramente la sensibilità del metodo elaborato non può essere paragonata alle tradizionali determinazioni con spettrometro di massa, ma si ritiene possa essere sufficientemente soddisfacente per valutare l'esposizione a benzene dei lavoratori a rischio e come analisi di screening rapida ed economica.

Modeling and Design of Phase Shifted Full Bridge Isolated DC-DC ZVS Converter with Peak Current Mode Control

Nowadays, there is a boom in the use of electrification. Electric vehicles are gaining interest worldwide due to various factors, including climate and environmental awareness. In this thesis, a step-down isolated power supply for electric tractors is investigated, specifically the phase-shifted full-bridge (PSFB) DC-DC with synchronous rectification and zero-voltage switching (ZVS). This converter was selected for its high-power capacity with high efficiency. A 3500 W PSFB converter with peak current control (PCCM) is designed and modeled in MATLAB. The input voltage range is from 550 V to 820 V and the output voltage range is limited to 9 V to 16 V with a maximum output current of 250 A. All components were commercially designed and selected, including magnetics for the high-frequency transformer and inductors, taking into account loss calculations. Zero voltage switching for the lagging leg is achieved at 13% to 100% load. The proven efficiency of the converter is around 90

Use Of Experimental Design To Optimize A Triple-potential Waveform To Develop A Method For The Determination Of Streptomycin And Dihydrostreptomycin In Pharmaceutical Veterinary Dosage Forms By Hplc-pad.

An HPLC-PAD method using a gold working electrode and a triple-potential waveform was developed for the simultaneous determination of streptomycin and dihydrostreptomycin in veterinary drugs. Glucose was used as the internal standard, and the triple-potential waveform was optimized using a factorial and a central composite design. The optimum potentials were as follows: amperometric detection, E1=-0.15V; cleaning potential, E2=+0.85V; and reactivation of the electrode surface, E3=-0.65V. For the separation of the aminoglycosides and the internal standard of glucose, a CarboPac™ PA1 anion exchange column was used together with a mobile phase consisting of a 0.070 mol L(-1) sodium hydroxide solution in the isocratic elution mode with a flow rate of 0.8 mL min(-1). The method was validated and applied to the determination of streptomycin and dihydrostreptomycin in veterinary formulations (injection, suspension and ointment) without any previous sample pretreatment, except for the ointments, for which a liquid-liquid extraction was required before HPLC-PAD analysis. The method showed adequate selectivity, with an accuracy of 98-107% and a precision of less than 3.9%.

Near full-length genome analysis of low prevalent human immunodeficiency virus type 1 subclade F1 in Sao Paulo, Brazil

Background: The genetic diversity of the human immunodeficiency virus type 1 (HIV-1) is critical to lay the groundwork for the design of successful drugs or vaccine. In this study we aimed to characterize and define the molecular prevalence of HIV-1 subclade F1 currently circulating in Sao Paulo, Brazil. Methods: A total of 36 samples were selected from 888 adult patients residing in Sao Paulo who had previously been diagnosed in two independent studies in our laboratory as being infected with subclade F1 based on pol subgenomic fragment sequencing. Proviral DNA was amplified from the purified genomic DNA of all 36 blood samples by 5 fragments overlapping PCR followed by direct sequencing. Sequence data were obtained from the 5 fragments of pure subclade F1 and phylogenetic trees were constructed and compared with previously published sequences. Subclades F1 that exhibited mosaic structure with other subtypes were omitted from any further analysis Results: Our methods of fragment amplification and sequencing confirmed that only 5 sequences inferred from pol region as subclade F1 also holds true for the genome as a whole and, thus, estimated the true prevalence at 0.56%. The results also showed a single phylogenetic cluster of the Brazilian subclade F1 along with non-Brazilian South American isolates in both subgenomic and the full-length genomes analysis with an overall intrasubtype nucleotide divergence of 6.9%. The nucleotide differences within the South American and Central African F1 strains, in the C2-C3 env, were 8.5% and 12.3%, respectively. Conclusion: All together, our findings showed a surprisingly low prevalence rate of subclade F1 in Brazil and suggest that these isolates originated in Central Africa and subsequently introduced to South America.

Reliability-based evaluation of design code provisions for circular concrete-filled steel columns

This paper presents an investigation of design code provisions for steel-concrete composite columns. The study covers the national building codes of United States, Canada and Brazil, and the transnational EUROCODE. The study is based on experimental results of 93 axially loaded concrete-filled tubular steel columns. This includes 36 unpublished, full scale experimental results by the authors and 57 results from the literature. The error of resistance models is determined by comparing experimental results for ultimate loads with code-predicted column resistances. Regression analysis is used to describe the variation of model error with column slenderness and to describe model uncertainty. The paper shows that Canadian and European codes are able to predict mean column resistance, since resistance models of these codes present detailed formulations for concrete confinement by a steel tube. ANSI/AISC and Brazilian codes have limited allowance for concrete confinement, and become very conservative for short columns. Reliability analysis is used to evaluate the safety level of code provisions. Reliability analysis includes model error and other random problem parameters like steel and concrete strengths, and dead and live loads. Design code provisions are evaluated in terms of sufficient and uniform reliability criteria. Results show that the four design codes studied provide uniform reliability, with the Canadian code being best in achieving this goal. This is a result of a well balanced code, both in terms of load combinations and resistance model. The European code is less successful in providing uniform reliability, a consequence of the partial factors used in load combinations. The paper also shows that reliability indexes of columns designed according to European code can be as low as 2.2, which is quite below target reliability levels of EUROCODE. (C) 2009 Elsevier Ltd. All rights reserved.

Reconstruction of large cranial defects in nonimmunosuppressed experimental design with human dental pulp stem cells

The main aim of this study is to evaluate the capacity of human dental pulp stem cells (hDPSC), isolated from deciduous teeth, to reconstruct large-sized cranial bone defects in nonimmunosuppressed (NIS) rats. To our knowledge, these cells were not used before in similar experiments. We performed two symmetric full-thickness cranial defects (5 x 8 mm) on each parietal region of eight NIS rats. In six of them, the left side was supplied with collagen membrane only and the right side (RS) with collagen membrane and hDPSC. In two rats, the RS had collagen membrane only and nothing was added at the left side (controls). Cells were used after in vitro characterization as mesenchymal cells. Animals were euthanized at 7, 20, 30, 60, and 120 days postoperatively and cranial tissue samples were taken from the defects for histologic analysis. Analysis of the presence of human cells in the new bone was confirmed by molecular analysis. The hDPSC lineage was positive for the four mesenchymal cell markers tested and showed osteogenic, adipogenic, and myogenic in vitro differentiation. We observed bone formation 1 month after surgery in both sides, but a more mature bone was present in the RS. Human DNA was polymerase chain reaction-amplified only at the RS, indicating that this new bone had human cells. The us e of hDPSC in NIS rats did not cause any graft. rejection. Our findings suggest that hDPSC is an additional cell resource for correcting large cranial defects in rats and constitutes a promising model for reconstruction of human large cranial defects in craniofacial surgery.

Modelling of cold-formed purlin-sheeting systems .1. Full model

Purlin-sheeting systems used for roofs and walls commonly take the form of cold-formed channel or zed section purlins, screw-connected to corrugated sheeting. These purlin-sheeting systems have been the subject of numerous theoretical and experimental investigations over the past three decades, but the complexity of the systems has led to great difficulty in developing a sound and general model. This paper presents a non-linear elasto-plastic finite element model, capable of predicting the behaviour of purlin-sheeting systems without the need for either experimental input or over simplifying assumptions. The model incorporates both the sheeting and the purlin, and is able to account for cross-sectional distortion of the purlin, the flexural and membrane restraining effects of the sheeting, and failure of the purlin by local buckling or yielding. The validity of the model is shown by its good correlation with experimental results. A simplified version of this model, which is more suitable for use in a design environment, is presented in a companion paper. (C) 1997 Elsevier Science Ltd.

Comparison of Full Versus Short Induced-Sleep Polysomnography for the Diagnosis of Sleep Apnea

Objectives/Hypothesis: Polysomnography (PSG) is the gold-standard method for diagnosing obstructive sleep apnea (OSA). However, the gap between demand and capacity in performing PSG is a major health-care problem. We sought to validate a short day-time induced sleep for the diagnosis of OSA. Study Design: Prospective diagnostic method validation. Methods: We studied 25 consecutive patients referred to the sleep laboratory and 15 healthy volunteers. All subjects were evaluated by means of full overnight PSG (Full-PSG) and short day-time induced-sleep PSG (Induced-PSG). Sleep was monitored during both procedures (Embla, 16 channels). Sleep was induced by slow intravenous drip infusion of midazolam. Results: The population studied (N = 40) was 60% male (mean age, 42 +/- 10 years; body mass index, 29 +/- 6.5 kg/m(2)). Sleep was successfully induced in all subjects, and no complications were observed (midazolam doses, 6.2 +/- 3.8 mg; time of induced sleep 41.5 +/- 18.9 minutes). The apnea-hypopnea index (AHI) and minimal oxygen saturation during Full-PSG versus Induced-PSG were similar: median AHI (with 25%-75% interquartile range) was 13 (3-35) events per hour versus 17 (4-36) events per hour, and median oxygen saturation was 84% (75-90) versus 85% (76-92); P = .89 and P = .53, respectively. The majority of the respiratory events during induced sleep were obstructive and similar to those observed during Full-PSG. AHI and lowest oxygen saturation during Induced-PSG correlated significantly with Full-PSG (r = 0.67 and r = 0.77, respectively). Sensitivity and specificity for the diagnosis of OSA (AHI > 15 events per hour) by Induced-PSG were 0.83 and 0.72, respectively. Conclusions: Induced-PSG by midazolam during the day is safe and correlates with Full-PSG; it therefore is a promising alternative method in the diagnosis of OSA.

The stochastic design of force-minimized compact magnets for high-field magnetic resonance imaging applications

New designs for force-minimized compact high-field clinical MRI magnets are described. The design method is a modified simulated annealing (SA) procedure which includes Maxwell forces in the error function to be minimized. This permits an automated force reduction in the magnet designs while controlling the overall dimensions of the system. As SA optimization requires many iterations to achieve a final design, it is important that each iteration in the procedure is rapid. We have therefore developed a rapid force calculation algorithm. Novel designs for short 3- and 4-T clinical MRI systems are presented in which force reduction has been invoked. The final designs provide large homogeneous regions and reduced stray fields in remarkable short magnets. A shielded 4-T design that is approximately 30% shorter than current designs is presented. This novel magnet generates a full 50-cm diameter homogeneous region.

Current density mapping approach for design of clinical magnetic resonance imaging magnets

Novel current density mapping (CDM) schemes are developed for the design of new actively shielded, clinical magnetic resonance imaging (MRI) magnets. This is an extended inverse method in which the entire potential solution space for the superconductors has been considered, rather than single current density layers. The solution provides an insight into the required superconducting coil pattern for a desired magnet configuration. This information is then used as an initial set of parameters for the magnet structure, and a previously developed hybrid numerical optimization technique is used to obtain the final geometry of the magnet. The CDM scheme is applied to the design of compact symmetric, asymmetric, and open architecture 1.0-1.5 T MRI magnet systems of novel geometry and utility. A new symmetric 1.0-T system that is just I m in length with a full 50-cm diameter of the active, or sensitive, volume (DSV) is detailed, as well as an asymmetric system in which a 50-cm DSV begins just 14 cm from the end of the coil structure. Finally a 1.0-T open magnet system with a full 50-cm DSV is presented. These new designs provide clinically useful homogeneous regions and have appropriately restricted stray fields but, in some of the designs, the DSV is much closer to the end of the magnet system than in conventional designs. These new designs have the potential to reduce patient claustrophobia and improve physician access to patients undergoing scans. (C) 2002 Wiley Periodicals, Inc.

Bridge strike reduction: optimising the design of markings

Cases of high-sided vehicles striking low bridges is a large problem in many countries, especially the UK. This paper describes an experiment to evaluate a new design of markings for low bridges. A full size bridge was constructed which was capable of having its overhead clearance adjusted. Subjects sat in a truck cab as. it drove towards the bridge and were asked to judge whether the vehicle could pass safely under the bridge. The main objective of the research, was to determine whether marking the bridge with a newly devised experimental marking would result in more cautious decisions from subjects regarding whether or not the experimental bridge structure could be passed under safely compared with the currently used UK bridge marking standard. The results show that the type of bridge marking influenced the level of caution associated with decisions regarding bridge navigation, with the new marking design producing the most cautious decisions for the two different bridge heights used, at all distances away from the bridge structure. Additionally, the distance before the bridge at which decisions were given had an effect on the level of caution associated with decisions regarding bridge navigation (the closer to the bridge, the more cautious the decisions became, irrespective of the marking design). The implications of these results for reducing the number of bridge strikes are discussed. (C) 2002 Elsevier Science Ltd. All rights reserved.

Full-scale demonstration of biological nutrient removal in a single tank SBR process

Complete biological nutrient removal (BNR) in a single tank, sequencing batch reactor (SBR) process, is demonstrated here at full-scale on a typical domestic wastewater. The unique feature of the UniFed process is the introduction of the influent into the settled sludge blanket during the settling and decant periods of the SBR operation. This achieves suitable conditions for denitrification and anaerobic phosphate release which is critical to successful biological phosphorus removal, It also achieves a selector effect, which helps in generating a compact, well settling biomass in the reactor. The results of this demonstration show that it is possible to achieve well over 90% removal of GOD, nitrogen and phosphorus in such a process. Effluent quality achieved over a six-month operating period directly after commissioning was: 29 mg/l GOD, 0.5 mg/l NH4-N, 1.5 mg/l NOx-N and 1.5 mg/l PO4-P (50%-iles of daily samples). During an 8-day, intensive sampling period, the effluent BOD5 was

Estudo morfofisiológico e anatômico de dois genótipos de cacaueiro (Theobroma cacao L.) submetidos a diferentes condições de radiação solar

A luminosidade desponta como um dos fatores abióticos de maior importância no estabelecimento das plantas, podendo ocasionar alterações a nível fisiológico e anatômico, interferindo diretamente no desenvolvimento das mesmas e consequentemente, sua produtividade. O cacaueiro (Theobroma cacao – Malvaceae) possui grande interesse econômico devido à utilização de suas sementes para produção de manteiga de cacau e chocolate. Neste sentido, o objetivo deste trabalho foi comparar características fisiológicas e anatômicas de dois genótipos de cacaueiro (PH 16 e IPIRANGA 01), submetidos a diferentes condições de radiação solar de modo a inferir a respeito das condições de luminosidade mais favoráveis ao desenvolvimento dos mesmos. Foram realizadas análises de crescimento, teor de pigmentos, trocas gasosas e anatômicas caulinares e foliares. O delineamento experimental foi em Blocos casualizados (DBC), com 4 repetições em arranjo fatorial 2 x 5, constituído de dois genótipos e 5 níveis de luminosidade (0% - pleno sol -, 18%, 30%, 50% e 80% de sombreamento), totalizando 40 parcelas com 10 plantas cada. Os dados obtidos foram submetidos à análise de variância e regressão. Os resultados de crescimento indicam maior adaptação, de ambos os genótipos, em condições de irradiância alta a moderada. O índice de qualidade de Dickson demonstrou maior capacidade de sobrevivência em condições de campo a níveis altos de irradiância para o genótipo PH 16 e a níveis de irradiância moderada para IPIRANGA 01. Os teores de pigmentos fotossintetizantes de IPIRANGA 01 mostram-se mais elevados na condição de 30% de sombreamento, enquanto que, para PH 16 os maiores teores foram observados em 50% de sombreamento. Ambos os genótipos demonstraram altas taxas de A, Ci, E, A/E, A/Gs e A/Ci, sob elevadas irradiâncias, assim como adaptações anatômicas caulinares e foliares a maiores luminosidades, tais como, maior espessamento do limbo foliar, parênquima paliçádico, esponjoso, limbo foliar, epiderme adaxial e densidade estomática, além de maior densidade e frequência de elementos de vaso e espessura do xilema secundário. Os genótipos PH 16 e IPIRANGA 01 apresentaram uma grande plasticidade em relação aos diferentes níveis de irradiância, no entanto, constatou-se que PH 16 apresentou melhor desempenho sob condições de alta irradiância, como as obtidas nos tratamentos a pleno sol e 18% de sombreamento, enquanto que, IPIRANGA 01 mostrou-se mais adaptado sob sombreamento moderado, a 30% de sombra.

Urease inhibitor (NBPT) and efficiency of single or split application of urea in wheat crop

NBPT (N-(n-butyl) thiophosphoric triamide), a urease inhibitor, has been reported as one of the most promising compounds to maximize urea nitrogen use in agricultural systems. The objective of this study was to evaluate the performance of irrigated wheat fertilized with urea or urea + NBPT as single or split application. The experiment was conducted from June to October 2006 in Viçosa, MG, Brazil. The experimental design followed a 2×2 factorial scheme, in which urea or urea + NBPT were combined with two modes of application: full dose at sowing (60kg ha-1) or split (20kg ha-1 at sowing + 40kg ha-1 as topdressing at tillering), in randomized blocks with ten replications. The split application of nitrogen fertilization does not improve the yield wheat under used conditions. The use of urease inhibitor improves the grain yield of wheat crop when urea is applied in topdressing at tillering, but its use does not promote difference when urea is applied in the furrow at planting.