Operational characteristics of four metering systems for agricultural fertilizers and amendments

The use of fertilizers and solid amendments in agriculture generates special interest for their effect on crop productivity, as well as for their environmental impact. The efficient use of these products demands knowing their physical and mechanical properties, the storing conditions effect and the operational characteristics of the metering systems used in the fertilizing equipment. In this context, the present study was developed with the purpose of evaluating the operational characteristics of different fertilizing metering systems and to determine the adequate metering system-product operational parameters, using powder lime, powder gypsum, granular 10-30-10 (N-P-K), and granular urea. Operational differences were established among four types of commercial fertilizer metering systems, including wire auger, star-shaped feed wheel, feed screw and ridged traction wheel. The study found that the unloading rate depends directly on the fertilizer metering system's rotating speed and is affected by particle size, repose angle, bulk density and moisture content of the applied product. The wire auger and star-shaped feed wheel metering systems were adequate for the distribution of powder products and the feed screw for granulated fertilizers. Furthermore, theoretical and experimental characteristic equations were established, defining curves for calibration and handling of the products plus the rotating speed range in which a better distributing behavior was achieved.

Anaerobic biodigestion of pigs feces in the initial, growing and finishing stages fed with diets formulated with corn or sorghum

The objective of this study was to evaluate the quality and the production of biogas and biofertilizer obtained from biodigester supplied with pig feces in the initial, growing and finishing stages, fed with diets formulated based on corn or sorghum. Twenty bench biodigesters were used with hydraulic retention time of 30 days and daily loads that contained 4 to 6% of total solids (TS) and 3.6 to 5.2% of volatile solids (VS). In the effluent of the biodigesters, mean levels of TS were observed ranging between 1.6 and 2.0% and of VS between 1.2 and 1.6%. The mean reductions of TS were 57.7 to 64.7% and of VS from 61.7 to 69.0%, and there was only difference in the finishing phase, in which the major averages reductions were produced by the biodigesters supplied with feces from animals fed with diets based on corn. In biodigesters supplied with feces from animals in the initial and growing stages fed with diets based on corn, were observed higher average productions of biogas and the greatest average potentials of biogas production. The average potentials obtained were 0.033; 0.181; 0.685; 0.788 and 1.132 m³ per kg of affluent, manure, TS added, VS added and VS reduced, respectively. No differences were found on the average content of methane in the biogas between diets and stages. The average concentrations of nutrients N, P, K, Ca, Mg, Na, Fe, Mn, Zn and Cu in the biodigester affluent and effluent, ranged between diets and stages.

Characterization and use of swine deep bedding ashes in cementitious composites

The deep bedding is a swine alternative production, especially in the finishing phase, whose byproduct can be recycled, reducing the environmental impact. The objectives of this study were to characterize the ash coming from the controlled burning of the swine deep bedding (SDBA) based on rice husk, and to evaluate their performance in composites as a partial substitute for Portland cement (PC). To measure the differences between SDBA and rice husk ash (RHA) as a reference, we have characterized: particle size distribution, real specific density, x-ray diffraction, electrical conductivity, scanning electron microscopy, chemical analysis and loss on ignition. Samples were prepared for two experimental series: control, and another one with the partial replacement of 30% of SDBA in relation to the mass of the Portland cement. According to the results obtained for physical and mechanical characterization, the composites with SDBA can be used as a constructive element in the rural construction.

Selection of microorganisms producer of lipase for fat removal from biodiesel purification water

The objective this study has been the selection of lipase productor microorganism, for removal of oils and grease, in the pre-treatment of biodiesel wastewater washing. For this, analyses of the physicist-chemistries characteristics had been made with the wastewater of the biodiesel washing, and then it had been isolated and chosen, by means of determinations of the lipase activity. Following, it was made a test of fat biodegradation, in the conditions: pH (5.95), temperature (35 ºC), rotation (180 rpm) and ammonium sulfate as nitrogen source (3 g L-1) and establishing as variable the two microorganism preselected and the time (24; 48; 72; 96 and 120 h). The biodiesel purification wastewater had presented high potential of environmental impact, presenting a concentration of O of 6.76 g L-1. From the six isolated microbiological cultures, two microorganisms (A and B) had been selected, with enzymatic index of 0.56 and 0.57, respectively. The treatment of the wastewater using the isolated microorganism (Klebsiella oxytoca) had 80% of the fatty removal in 48 h.

Precision agriculture in Australia: present status and recent developments

A brief account of the present status of Precision Agriculture (PA) in Australia is presented, and areas of opportunity in the grains, sugar and wine industries are identified. In particular, these relate to the use of spatially-distributed experimentation to fine-tune management so as to achieve production efficiencies, reduced risk of environmental impact and enhanced food security, and the management of crop quality through selective harvesting and product streaming. The latter may be an important avenue by which farmers can take a more active role in the off-farm part of agricultural value chains. The important role of grower groups in facilitating PA adoption is also discussed.

Rheological behavior of Chlorella sp. e Scenedesmus sp. cultures in different biomass concentrations

Studies involving the use of microalgae are increasingly intensifying for the potential they present to produce biofuels, because they are a renewable energy source that does not compete directly with food production, and because they enable the obtaining of a fuel with less environmental impact when compared to fossil fuel. In this context, the use of microalgae is directly associated to its capacity to be produced on a large scale and to be extracted from the culture medium. Rheological studies are important for obtaining the information needed in the elaboration of projects and equipment that will be used in various operations existing in systems of production and extraction of algal biomass. In the evaluation of different levels of dry biomass concentration, studies have been conducted of the rheological behavior of cultures of Chlorella sp. BR001 and Scenedesmus sp. BR003. The Power Law model adjusted well to the data of shear stress as a function of strain rate. In all concentrations the cultures showed non-Newtonian behavior. It was observed to Scenedesmus sp. BR003 little effect of biomass concentration on the apparent viscosity and shear stress.

Energy demand in citrus production under varied operational efficiency values

Citrus orchards are very important in Brazil, especially in São Paulo State, where occupy an area of 600,000 ha approximately. To identify sustainability degree of citrus production system, an energy analysis allows evaluating efficiency of direct and indirect applied inputs. Thus, this study aimed to evaluate citrus production system under energetic point of view, in which invested energy is paid back with citrus production; being compared within three scenarios for operational field efficiency. As result, by sensitivity analysis was determined that fuel was the main energy demander, followed by pesticides and fertilizers. In operational work capacity analysis, all combinations between efficiency (minimum, typical and maximum) and yield levels became positive in the seventh year, except for the combination minimum efficiency and 10 % less yield, positive in the eighth year. The best combination (maximum efficiency and 10 % more yield) has promoted investment payoff around the sixth and seventh year. By this study, it is possible to determine the total energy demand to produce citrus and indentify the applied inputs that need more attention by the decision-makers. Labor and seedlings can be ommited for further studies with citrus, since they were irrelevant. Management of agricultural machinery may pose an important role on decreasing environmental impact of citrus production.

The Design and Implementation of a Power Management Feature to a Configuration Management System

Green IT is a term that covers various tasks and concepts that are related to reducing the environmental impact of IT. At enterprise level, Green IT has significant potential to generate sustainable cost savings: the total amount of devices is growing and electricity prices are rising. The lifecycle of a computer can be made more environmentally sustainable using Green IT, e.g. by using energy efficient components and by implementing device power management. The challenge using power management at enterprise level is how to measure and follow-up the impact of power management policies? During the thesis a power management feature was developed to a configuration management system. The feature can be used to automatically power down and power on PCs using a pre-defined schedule and to estimate the total power usage of devices. Measurements indicate that using the feature the device power consumption can be monitored quite precisely and the power consumption can be reduced, which generates electricity cost savings and reduces the environmental impact of IT.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

Celioscopic liver biopsy in silver catfish (Rhamdia quelen)

Endosurgery has been used for assessment of fish celomatic cavity, as well as for obtaining biopsies for organic analysis. Such minimally invasive access may also be used for the analysis of environmental impact on biomarkers of pollution. In Brazil, studies and literature regarding the use of celioscopy in fish are sparse. The purpose of the current study was to develop a two-port celioscopy technique to obtain liver biopsy in silver catfish (Rhamdia quelen). Six adult female silver catfish were used. The animals were anesthetized and the inspection of the celomatic cavity were performed using a telescope and celioscopic-guided liver biopsy were taken using laparoscopic Kelly forceps. On the early postoperative period, the animals were released in a confined water reservoir where mortality could be checked. The liver samples were sent for histological assessment. There were no complications during surgery on early postoperative period. It was possible to visualize meticulously several organs (liver, spleen, stomach, pancreas, swim bladder, ovaries, bowel and transverse septum). In conclusion, the surgical technique and the anesthetic protocol proposed were suitable to perform liver biopsies in silver catfish and provided low morbidity.

Leaching of Picloram in ultisol under different rainfall volumes

The present study aimed to evaluate the leaching potential of Picloram in Ultisol columns under different rainfall amounts. For such, 30 treatments were evaluated (one soil associated with three levels of rainfall and ten depths).The experiments were arranged in a split-plot design, in a completely randomized design, with four replications. PVC columns of 10 cm in diameter and 50 cm in length were filled with these soils, moistened, and placed upright for 48 hours to drain the excess water. The herbicide was applied and rainfall simulations were carried out at specified intensities, according to the treatments, to force Picloram leaching. After 72 hours, all the columns were arranged in a horizontal position and opened lengthwise. Then, soil sampling was carried out every 5 cm of depth for subsequent herbicide extraction and quantification and analysis by high performance liquid chromatography. The remaining soil samples were placed in plastic pots, and, at the respective depths, the indicator species Cucumis sativus was sown. Twenty-one days after the emergence (DAE) of the indicator plants, evaluations were conducted to verify the symptoms of toxicity caused by Picloram in the plants. It was concluded that Picloram leaching is directly dependent on the volume of rain applied. The herbicide reached the deepest regions in the soil with the highest intensity of rain. The results obtained by bioassay were in agreement with those found by liquid chromatography.

Variations in weed population densities, rate of change and community diversity in RR-soybeans and RR-maize strip crops under two herbicide strategies

Concerns about the sustainability of large-scale, direct-drilled RR-soybeans (Glycine max), and RR-maize (Zea mays) under monoculture in central Argentina are growing steadily. An experiment was conducted during three consecutive years to determine the effects of crops and systems (monocultures and strips) and herbicide strategy on weed density, population rate of change (l), b community diversity (H´), crop yields and Land Equivalent Ratio (LER). Not only crops but also crop systems differentially influenced weed densities along their growth and development. For crop harvests, weed densities increased in both maize crop systems as compared to in the one for soybeans, but the lowest increase occurred in soybean strips. Differences were leveled by both herbicide strategies, which achieved 73% efficacy during the critical periods in both crops. l of annual monocotyledonous increased, thus shifting the weed community composition. Species richness and H´ were not affected by crop systems, but both herbicide strategies, particularly POST, either in soybeans in monoculture or in maize strips, significantly enhanced H´. Crop yields significantly increased in the maize-strip system with POST (Year 1) or PRE (Years 2 and 3) strategies, thus increasing LER above 1. Herbicide Environmental Load treatments fall within very low or low field use rating.

Selective leaching of multimetal tailings

Depletion of high grade mineral resources, tightening of environmental regulations and the environmental impact of acid mine drainage caused by sulfidic minerals continuously increase the interest in processing tailings and other mine waste. Treating waste requires additional capital and operational input, but the decrease in size and need of tailings ponds and permits decrease the overall costs. Treatment and utilization of the tailings could also bring added revenue by the recovery of valuables. Leaching of metal sulfides is very demanding and time consuming and hence process conditions need to be carefully optimized. The leaching of sulfides is affected by for example the choice of leaching agent, its concentration and temperature, pH, the redox potential, pressure, pulp density and particle size distribution. With reference to the mine case study the leaching of nickel and copper sulfides, especially the primary minerals pentlandite and chalcopyrite were investigated. Leaching behavior and recoveries for nickel, copper and iron were found out by sulfuric and citric acid leaching experiments using tailings samples of high and low sulfur content. Moderate recoveries were obtained and citric acid seemed more attractive. Increase in temperature and decrease in pulp density had positive effect on the recovery and pH was also proven to have a significant effect on the recovery of valuables. The rate determining step was determined through kinetic modeling in case of all valuables separately. Leaching was controlled by diffusion. The investigated multimetal tailing showed moderate potential in recovering of metal valuables from low grade tailing deposits. The process conditions should however be further optimized.

Sorption of fomesafen in Brazilian soils

The study of the dynamics of a herbicide in the soil focus on the interactions with environmental components to obtain agronomic efficiency, ensuring selectivity to the culture and risk reduction of environmental impact. This study evaluated the sorption process of fomesafen in the Brazilian soils Ultisol, Cambisol, and Organosol. Besides soil, washed sand was used as an inert material for determination of the sorption ratio of fomesafen in the soil. The bioassay method was applied, using Sorghum vulgare plants as bio-indicator of herbicide presence. Plant poisoning evaluation and harvest for dry matter determination were carried out 21 days after sorghum sowing. To calculate C50, the nonlinear log-logistic model was applied and sorption ratios of the herbicide were obtained in different soils. The decreasing sorption ratio of formesafen in the soils was: Organosol > Ultisol > Cambisol. It was concluded that the contents of organic matter and clay in the soils were the attributes that most influenced fomesafen sorption.

Competition periods of crabgrass with rice and soybean crops

Determining the periods of weed competition with crops helps the producer to choose the most appropriate time to use weed control practices. This strategy allows for the reduction of the number of herbicide applications, reducing costs and the environmental impact of pesticides. The objectives were to determine the period before the interference (PBI) of crabgrass (Digitaria ciliaris) competing with flooded rice, the critical period of interference prevention (CPIP) of crabgrass with soybean and the effects of competition on the grains yield and their components. Experiments were conducted with the coexistence of BRS Querência rice cultivar with crabgrass, for periods of 0, 7, 14, 21, 28, 35, and 110 days after emergency (DAE) and Fundacep 53RR soybean cultivar, whose periods of coexistence and control of crabgrass were 0, 7, 14, 21, 28, 35, and 156 DAE. Rice can grow with crabgrass infestation until 18 DAE, while soybean should remain free from the presence of crabgrass in the period between 23 and 50 DAE. The grain yield and its components, in the crops studied, are affected when grown with crabgrass.