The identification and rapid extraction of hydrocarbons from Nicotiana glauca : A potential advanced renewable biofuel source

Declining fossil fuels reserves, a need for increased energy security and concerns over carbon emissions from fossil fuel use are the global drivers for alternative, renewable, biosources of fuels and chemicals. In the present study the identification of long chain (C29–C33) saturated hydrocarbons from Nicotiana glauca leaves is reported. The occurrence of these hydrocarbons was detected by gas chromatography–mass spectrometry (GC–MS) and identification confirmed by comparison of physico-chemical properties displayed by the authentic standards available. A simple, robust procedure was developed to enable the generation of an extract containing a high percentage of hydrocarbons (6.3% by weight of dried leaf material) higher than previous reports in other higher plant species consequently, it is concluded that N. glauca could be a crop of greater importance than previously recognised for biofuel production. The plant can be grown on marginal lands, negating the need to compete with food crops or farmland, and the hydrocarbon extract can be produced in a non-invasive manner, leaving remaining biomass intact for bioethanol production and the generation of valuable co-products.

Evaluation of a pilot-scale oil extraction from microalgae for biodiesel production

Biodiesel derived from microalgae is one of a suite of potential solutions to meet the increasing demand for a renewable, carbon-neutral energy source. However, there are numerous challenges that must be addressed before algae biodiesel can become commercially viable. These challenges include the economic feasibility of harvesting and dewatering the biomass and the extraction of lipids and their conversion into biodiesel. Therefore, it is essential to find a suitable extraction process given these processes presently contribute significantly to the total production costs which, at this stage, inhibit the ability of biodiesel to compete financially with petroleum diesel. This study focuses on pilot-scale (100 kg dried microalgae) solvent extraction of lipids from microalgae and subsequent transesterification to biodiesel. Three different solvents (hexane, isopropanol (IPA) and hexane + IPA (1:1)) were used with two different extraction methods (static and Soxhlet) at bench-scale to find the most suitable solvent extraction process for the pilot-scale. The Soxhlet method extracted only 4.2% more lipid compared to the static method. However, the fatty acid profiles of different extraction methods with different solvents are similar, suggesting that none of the solvents or extraction processes were biased for extraction of particular fatty acids. Considering the cost and availability of the solvents, hexane was chosen for pilot-scale extraction using static extraction. At pilot-scale the lipid yield was found to be 20.3% of total biomass which is 2.5% less than from bench scale. Extracted fatty acids were dominated by polyunsaturated fatty acids (PUFAs) (68.94±0.17%) including 47.7±0.43 and 17.86±0.42% being docosahexaenoic acid (DHA) (C22:6) and docosapentaenoic acid (DPA) (C22:5, ω-3), respectively. These high amounts of long chain poly unsaturated fatty acids are unique to some marine microalgae and protists and vary with environmental conditions, culture age and nutrient status, as well as with cultivation process. Calculated physical and chemical properties of density, viscosity of transesterified fatty acid methyl esters (FAMEs) were within the limits of the biodiesel standard specifications as per ASTM D6751-2012 and EN 14214. The calculated cetane number was, however, significantly lower (17.8~18.6) compared to ASTM D6751-2012 or EN 14214-specified minimal requirements. We conclude that the obtained microalgal biodiesel would likely only be suitable for blending with petroleum diesel to a maximum of 5 to 20%.

Simulation of plant cell shrinkage during drying : A SPH–DEM approach

Plant based dried food products are popular commodities in global market where much research is focused to improve the products and processing techniques. In this regard, numerical modelling is highly applicable and in this work, a coupled meshfree particle-based two-dimensional (2-D) model was developed to simulate micro-scale deformations of plant cells during drying. Smoothed Particle Hydrodynamics (SPH) was used to model the viscous cell protoplasm (cell fluid) by approximating it to an incompressible Newtonian fluid. The visco-elastic characteristic of the cell wall was approximated to a Neo-Hookean solid material augmented with a viscous term and modelled with a Discrete Element Method (DEM). Compared to a previous work [H. C. P. Karunasena, W. Senadeera, Y. T. Gu and R. J. Brown, Appl. Math. Model., 2014], this study proposes three model improvements: linearly decreasing positive cell turgor pressure during drying, cell wall contraction forces and cell wall drying. The improvements made the model more comparable with experimental findings on dried cell morphology and geometric properties such as cell area, diameter, perimeter, roundness, elongation and compactness. This single cell model could be used as a building block for advanced tissue models which are highly applicable for product and process optimizations in Food Engineering.

Analysis of genetically modified red-fleshed apples reveals effects on growth and consumer attributes

Consumers of whole foods, such as fruits, demand consistent high quality and seek varieties with enhanced health properties, convenience or novel taste. We have raised the polyphenolic content of apple by genetic engineering of the anthocyanin pathway using the apple transcription factor MYB10. These apples have very high concentrations of foliar, flower and fruit anthocyanins, especially in the fruit peel. Independent lines were examined for impacts on tree growth, photosynthesis and fruit characteristics. Fruit were analysed for changes in metabolite and transcript levels. Fruit were also used in taste trials to study the consumer perception of such a novel apple. No negative taste attributes were associated with the elevated anthocyanins. Modification with this one gene provides near isogenic material and allows us to examine the effects on an established cultivar, with a view to enhancing consumer appeal independently of other fruit qualities. © 2012 Society for Experimental Biology, Association of Applied Biologists and Blackwell Publishing Ltd.

Trait and behavioural motor control is associated with resistance to overconsumption

While overall obesity rates are rising, a minority of individuals appear to resist overconsumption and remain lean in spite of an ‘obesogenic’ environment. Studying the factors hypothesised to underpin behaviours associated with resistance to overconsumption may inform weight management strategies in an adverse environment. Trait (BIS-11) and behavioural (response inhibition, GoStop) self control were assessed in the laboratory. Snack food consumption was measured covertly via a sham taste test. Lack of motor control was positively correlated (r = .32, p <. 05) and successful response inhibition was negatively correlated (r = −.35, p <. 05) with snack food intake. Low motor control was also associated with further food intake when satiated (r = .39, p < .01). These relationships were independent of self-reported palatability and perceived reward value of the food. Motor control may be an important factor implicated in ‘mindless’ eating in an environment abundant in palatable, energy-dense snack foods.

Nutrition and physical activity policies and practices in family child care homes

Background Family child care homes (FCCHs) are the second-largest provider of nonrelative care in the U.S. However, despite providing care for nearly 1.9 million children aged <5 years, little is known about the nutrition and physical activity practices of FCCHs. Purpose To address this gap, this study aims to describe policies and practices related to nutrition and physical activity in a representative sample of FCCHs. Methods A stratified random sample of registered FCCHs operating in Kansas (N=297) completed the Nutrition and Physical Activity Self Assessment for Child Care (NAPSACC) instrument. Prevalence estimates and 95% CIs for meeting or exceeding accepted child care standards were calculated using SAS PROC SURVEYFREQ. Results Most providers either met or exceeded child care standards related to serving fruit and vegetables and provision of daily physical activity. Very few providers reported serving fried meats or vegetables or unhealthy snack foods on a regular basis. Areas of concern included infrequent servings of low-fat milk, frequent use of unhealthy foods for celebrations, widespread use of TV and video games throughout the day, restricting physical activity for children who misbehave, and lack of appropriate indoor spaces for physical activity. Only a small percentage of providers reported receiving regular training in nutrition or physical activity. Relatively few providers had written guidelines on nutrition or physical activity. Conclusions Some strengths were exhibited by FCCHs, but substantial weaknesses were shown with respect to meeting established child care standards for nutrition and physical activity. Interventions to promote healthy eating and regular physical activity in FCCHs are thus warranted.

Crushed tablets : does the administration of food vehicles and thickened fluids to aid medication swallowing alter drug release?

Purpose. To evaluate the influence of co-administered vehicles on in vitro dissolution in simulated gastric fluid of crushed immediate release tablets as an indicator for potential drug bioavailability compromise. Methods. Release and dissolution of crushed amlodipine, atenolol, carbamazepine and warfarin tablets were tested with six foods and drinks that are frequently used in the clinical setting as mixers for crushed medications (water, orange juice, honey, yoghurt, strawberry jam and water thickened with Easythick powder) in comparison to whole tablets. Five commercial thickening agents (Easythick Advanced, Janbak F, Karicare, Nutilis, Viscaid) at three thickness levels were tested for their effect on the dissolution of crushed atenolol tablets. Results. Atenolol dissolution was unaffected by mixing crushed tablets with thin fluids or food mixers in comparison to whole tablets or crushed tablets in water, but amlodipine was delayed by mixing with jam. Mixing crushed warfarin and carbamazepine tablets with honey, jam or yoghurt caused them to resemble the slow dissolution of whole tablets rather than the faster dissolution of crushed tablets in water or orange juice. Crushing and mixing any of the four medications with thickened water caused a significant delay in dissolution. When tested with atenolol, all types of thickening agents at the greatest thickness significantly restricted dissolution, and products that are primarily based on xanthan gum also delayed dissolution at the intermediate thickness level. Conclusions. Dissolution testing, while simplistic, is a widely used and accepted method for comparing drug release from different formulations as an indicator for in vivo bioavailability. Thickened fluids have the potential to retard drug dissolution when used at the thickest levels. These findings highlight potential clinical implications of the addition of these agents to medications for the purpose of dose delivery and indicate that further investigation of thickened fluids and their potential to influence therapeutic outcomes is warranted.

Label-free SERS for natural product provenance

Introduction Natural product provenance is important in the food, beverage and pharmaceutical industries, for consumer confidence and with health implications. Raman spectroscopy has powerful molecular fingerprint abilities. Surface Enhanced Raman Spectroscopy’s (SERS) sharp peaks allow distinction between minimally different molecules, so it should be suitable for this purpose. Methods Naturally caffeinated beverages with Guarana extract, coffee and Red Bull energy drink as a synthetic caffeinated beverage for comparison (20 µL ea.) were reacted 1:1 with Gold nanoparticles functionalised with anti-caffeine antibody (ab15221) (10 minutes), air dried and analysed in a micro-Raman instrument. The spectral data was processed using Principle Component Analysis (PCA). Results The PCA showed Guarana sourced caffeine varied significantly from synthetic caffeine (Red Bull) on component 1 (containing 76.4% of the variance in the data). See figure 1. The coffee containing beverages, and in particular Robert Timms (instant coffee) were very similar on component 1, but the barista espresso showed minor variance on component 1. Both coffee sourced caffeine samples varied with red Bull on component 2, (20% of variance). ************************************************************ Figure 1 PCA comparing a naturally caffeinated beverage containing Guarana with coffee. ************************************************************ Discussion PCA is an unsupervised multivariate statistical method that determines patterns within data. Figure 1 shows Caffeine in Guarana is notably different to synthetic caffeine. Other researchers have revealed that caffeine in Guarana plants is complexed with tannins. Naturally sourced/ lightly processed caffeine (Monster Energy, Espresso) are more inherently different than synthetic (Red Bull) /highly processed (Robert Timms) caffeine, in figure 1, which is consistent with this finding and demonstrates this technique’s applicability. Guarana provenance is important because it is still largely hand produced and its demand is escalating with recognition of its benefits. This could be a powerful technique for Guarana provenance, and may extend to other industries where provenance / authentication are required, e.g. the wine or natural pharmaceuticals industries.

Gelatinase A (MMP-2) activation by skin fibroblasts : dependence on MT1-MMP expression and fibrillar collagen form

The respective requirements of collagen and MT1-MMP in the activation of MMP-2 by primary fibroblast cultures were explored further. Three-dimensional gels enriched in human collagen types I and III or composed of recombinant human type II or III collagen, caused increased MT1-MMP production (mRNA and protein) and induced MMP-2 activation. Only marginal induction was seen with dried monomeric collagen confirming the need for collagen fibrillar organisation for activation. To our surprise, relatively low amounts (as low as 25 μg/ml) of acid soluble type I collagen added to fibroblast cultures also induced potent MMP-2 activation. However, the requirement for collagen fibril formation by the added collagen was indicated by the inhibition seen when the collagen was pre-incubated with a fibril-blocking peptide, and the reduced activation seen with alkali-treated collagen preparations known to have impaired fibrilisation. Pre-treatment of the collagen with sodium periodate also abrogated MMP-2 activation induction. Further evidence of the requirement for collagen fibril formation was provided by the lack of activation when type IV collagen, which does not form collagen fibrils, was added in the cultures. Fibroblasts derived from MT1-MMP-deficient mice were unable to activate MMP-2 in response to either three-dimensional collagen gel or added collagen solutions, compared to their littermate controls. Collectively, these data indicate that the fibrillar structure of collagen and MT1-MMP are essential for the MMP-2 activational response in fibroblasts.

Maternal feeding self-efficacy and fruit and vegetable intakes in infants. Results from the SAIDI study

Adequate consumption of fruits and vegetables (FV) is a characteristic of a healthy diet but remains a challenge in nutrition interventions. This cross-sectional study explored the multi-directional relationships between maternal feeding self-efficacy, parenting confidence, child feeding behaviour, exposure to new food and FV intake in a cohort of 277 infants. Mothers with healthy infants weighing ≥2500 g and ≥37 weeks gestation were recruited post-natally from 11 South Australian hospitals. Socio-demographic datawere collected at recruitment. At 6 months postnatal, infantswereweighed and measured, andmothers completed a questionnaire exploring their perceptions of child feeding behaviour and child exposure to newfoods. The questionnaire also included the Short Temperament Scale for Infants, Kessler 10 to measure maternal psychological distress and 5 items measuring maternal feeding self-efficacy. The number of occasions and variety of FV (number of subgroups within food groups) consumed by infants were estimated from a 24-hour dietary recall and 2 days food record. Structural equation modellingwas performed using Mplus version 6.11. Median (IQR) variety scores were 2 (1–3) for fruit and 3 (2–5) for vegetable intake. The most popular FV consumed were apple (n = 108, 45.0%) and pumpkin (n = 143, 56.3%). None of the variables studied predicted the variety of child fruit intake. Parenting confidence, exposure to new foods and child feeding behaviourwere indirectly related to child vegetable intake through maternal feeding self-efficacy while total number of children negatively predicted child vegetable variety (p < 0.05). This highlights the need for addressing antecedents of maternal feeding self-efficacy and the family eating environment as key strategies towards development of healthy eating in children.

The influence of maternal infant feeding practices and beliefs on the expression of food neophobia in toddlers

Food neophobia is a highly heritable trait characterized by the rejection of foods that are novel or unknown and potentially limits dietary variety, with lower intake and preference particularly for fruits and vegetables. Understanding non-genetic (environmental) factors that may influence the expression of food neophobia is essential to improving children’s consumption of fruits and vegetables and encouraging the adoption of healthier diets. The aim of this study was to examine whether maternal infant feeding beliefs (at four months) were associated with the expression of food neophobia in toddlers and whether controlling feeding practices mediated this relationship. Participants were 244 first-time mothers (M = 30.4, SD = 5.1 years) allocated to the control group of the NOURISH randomized controlled trial. The relationships between infant feeding beliefs (Infant Feeding Questionnaire) at four months and controlling child feeding practices (Child Feeding Questionnaire) and food neophobia (Child Food Neophobia Scale) at 24 months were tested using correlational and multiple linear regression models (adjusted for significant covariates). Higher maternal Concern about infant under-eating and becoming underweight at four months was associated with higher child food neophobia at two years. Similarly, lower Awareness of infant hunger and satiety cues was associated with higher child food neophobia. Both associations were significantly mediated by mothers’ use of Pressure to eat. Intervening early to promote positive feeding practices to mothers may help reduce the use of controlling practices as children develop. Further research that can further elucidate the bi-directional nature of the mother-child feeding relationship is still required.

A particle based model to simulate microscale morphological changes of plant tissues during drying

Fundamental understanding on microscopic physical changes of plant materials is vital to optimize product quality and processing techniques, particularly in food engineering. Although grid-based numerical modelling can assist in this regard, it becomes quite challenging to overcome the inherited complexities of these biological materials especially when such materials undergo critical processing conditions such as drying, where the cellular structure undergoes extreme deformations. In this context, a meshfree particle based model was developed which is fundamentally capable of handling extreme deformations of plant tissues during drying. The model is built by coupling a particle based meshfree technique: Smoothed Particle Hydrodynamics (SPH) and a Discrete Element Method (DEM). Plant cells were initiated as hexagons and aggregated to form a tissue which also accounts for the characteristics of the middle lamella. In each cell, SPH was used to model cell protoplasm and DEM was used to model the cell wall. Drying was incorporated by varying the moisture content, the turgor pressure, and cell wall contraction effects. Compared to the state of the art grid-based microscale plant tissue drying models, the proposed model can be used to simulate tissues under excessive moisture content reductions incorporating cell wall wrinkling. Also, compared to the state of the art SPH-DEM tissue models, the proposed model better replicates real tissues and the cell-cell interactions used ensure efficient computations. Model predictions showed good agreement both qualitatively and quantitatively with experimental findings on dried plant tissues. The proposed modelling approach is fundamentally flexible to study different cellular structures for their microscale morphological changes at dehydration.

A novel approach for numerical simulation of plant tissue shrinkage during drying

Drying is a key processing techniques used in food engineering which demands continual developments on advanced analysis techniques in order to optimize the product and the process. In this regard, plant based materials are a frequent subject of interest where microstructural studies can provide a clearer understanding on the fundamental physical mechanisms involved. In this context, considering numerous challenges of using conventional numerical grid-based modelling techniques, a meshfree particle based model was developed to simulate extreme deformations of plant microstructure during drying. The proposed technique is based on a particle based meshfree method: Smoothed Particle Hydrodynamics (SPH) and a Discrete Element Method (DEM). A tissue model was developed by aggrading individual cells modelled with SPH-DEM coupled approach by initializing the cells as hexagons and aggregating them to form a tissue. The model also involves a middle lamella resembling real tissues. Using the model, different dried tissue states were simulated with different moisture content, the turgor pressure, and cell wall contraction effects. Compared to the state of the art grid-based microscale plant tissue drying models, the proposed model is capable of simulating plant tissues at lower moisture contents which results in excessive shrinkage and cell wall wrinkling. Model predictions were compared with experimental findings and a fairly good agreement was observed both qualitatively and quantitatively.

Food and beverage intake in Australian children aged 12-16 months participating in the NOURISH and SAIDI studies

Objective To describe the quantity and diversity of food and beverage intake in Australian children aged 12–16 months and to determine if the amount and type of milk intake is associated with dietary diversity. Methods Mothers participating in the NOURISH and South Australian Infant Dietary Intake (SAIDI) studies completed a single 24-hour recall of their child's food intake, when children (n=551) were aged 12–16 months. The relationship between dietary diversity and intake of cow's milk, formula or breastmilk was examined using one-way ANOVA. Results Dairy and cereal were the most commonly consumed food groups and the greatest contributors to daily energy intake. Most children ate fruit (87%) and vegetables (77%) on the day of the 24-hour recall while 91% ate discretionary items. Half the sample ate less than 30 g of meat/alternatives. A quarter of the children were breastfeeding while formula was consumed by 32% of the sample, providing 29% of daily energy intake. Lower dietary diversity was associated with increased formula intake. Conclusions The quality of dietary intake in this group of young children is highly variable. Most toddlers were consuming a diverse diet, though almost all ate discretionary items. The amount and type of meat/alternatives consumed was poor. Implications Health professionals should advise parents to offer iron-rich foods, while limiting discretionary choices and use of formula at an age critical in the development of long-term food preferences.

Application of meshfree methods to numerically simulate microscale deformations of different plant food materials during drying

Plant food materials have a very high demand in the consumer market and therefore, improved food products and efficient processing techniques are concurrently being researched in food engineering. In this context, numerical modelling and simulation techniques have a very high potential to reveal fundamentals of the underlying mechanisms involved. However, numerical modelling of plant food materials during drying becomes quite challenging, mainly due to the complexity of the multiphase microstructure of the material, which undergoes excessive deformations during drying. In this regard, conventional grid-based modelling techniques have limited applicability due to their inflexible grid-based fundamental limitations. As a result, meshfree methods have recently been developed which offer a more adaptable approach to problem domains of this nature, due to their fundamental grid-free advantages. In this work, a recently developed meshfree based two-dimensional plant tissue model is used for a comparative study of microscale morphological changes of several food materials during drying. The model involves Smoothed Particle Hydrodynamics (SPH) and Discrete Element Method (DEM) to represent fluid and solid phases of the cellular structure. Simulation are conducted on apple, potato, carrot and grape tissues and the results are qualitatively and quantitatively compared and related with experimental findings obtained from the literature. The study revealed that cellular deformations are highly sensitive to cell dimensions, cell wall physical and mechanical properties, middle lamella properties and turgor pressure. In particular, the meshfree model is well capable of simulating critically dried tissues at lower moisture content and turgor pressure, which lead to cell wall wrinkling. The findings further highlighted the potential applicability of the meshfree approach to model large deformations of the plant tissue microstructure during drying, providing a distinct advantage over the state of the art grid-based approaches.