Modelling the combined impacts of climate change and direct anthropogenic drivers on the ecosystem of the northwest European continental shelf

The potential response of the marine ecosystem of the northwest European continental shelf to climate change under a medium emissions scenario (SRES A1B) is investigated using the coupled hydrodynamics-ecosystem model POLCOMS-ERSEM. Changes in the near future (2030–2040) and the far future (2082–2099) are compared to the recent past (1983–2000). The sensitivity of the ecosystem to potential changes in multiple anthropogenic drivers (river nutrient loads and benthic trawling) in the near future is compared to the impact of changes in climate. With the exception of the biomass of benthic organisms, the influence of the anthropogenic drivers only exceeds the impact of climate change in coastal regions. Increasing river nitrogen loads has a limited impact on the ecosystem whilst reducing river nitrogen and phosphate concentrations affects net primary production(netPP) and phytoplankton and zooplankton biomass. Direct anthropogenic forcing is seen to mitigate/amplify the effects of climate change. Increasing river nitrogen has the potential to amplify the effects of climate change at the coast by increasing netPP. Reducing river nitrogen and phosphate mitigates the effects of climate change for netPP and the biomass of small phytoplankton and large zooplankton species but amplifies changes in the biomass of large phytoplankton and small zooplankton.

Using hypnosis to facilitate direct observation of multiple tics and self-monitoring in a typically developing teenager

A hypnotic induction technique was used to facilitate direct observation of multiple tics in a typically developing teenager in a home setting. A comprehensive habit reversal program then was implemented, including awareness training, competing response training, relaxation training, self-monitoring, social support and contingency management. Duration of relaxation was then self-monitored using a changing criterion design. The procedure eliminated multiple tics and achieved long-term maintenance of treatment gains. Implications for assessing and treating tics are discussed.

The Development of a Two-Dimensional Transient Catalyst Model for Direct Injection Two-Stroke Applications.

This paper describes the development of a two-dimensional transient catalyst model. Although designed primarily for two-stroke direct injection engines, the model is also applicable to four-stroke lean burn and diesel applications. The first section describes the geometries, properties and chemical processes simulated by the model and discusses the limitations and assumptions applied. A review of the modeling techniques adopted by other researchers is also included. The mathematical relationships which are used to represent the system are then described, together with the finite volume method used in the computer program. The need for a two-dimensional approach is explained and the methods used to model effects such as flow and temperature distribution are presented. The problems associated with developing surface reaction rates are discussed in detail and compared with published research. Validation and calibration of the model is achieved by comparing predictions with measurements from a flow reactor. While an extensive validation process, involving detailed measurements of gas composition and thermal gradients, has been completed, the analysis is too detailed for publication here and is the subject of a separate technical paper.

The Validation of a Two-Dimensional Transient Catalyst Model for Direct Injection Two-Stroke Applications

This paper describes the detailed validation of a computer model designed to simulate the transient light-off in a two-stroke oxidation catalyst. A plug flow reactor is employed to provide measurements of temperature and gas concentration at various radial and axial locations inside the catalyst. These measurements are recorded at discrete intervals during a transient light-off in which the inlet temperature is increased from ambient to 300oC at rates of up to 6oC/sec. The catalyst formulation used in the flow reactor, and its associated test procedures, are then simulated by the computer and a comparison made between experimental readings and model predictions. The design of the computer model to which this validation exercise relates is described in detail in a separate technical paper. The first section of the paper investigates the warm-up characteristics of the substrate and examines the validity of the heat transfer predictions between the wall and the gas in the absence of chemical reactions. The predictions from a typical single-component CO transient light-off test are discussed in the second section and are compared with experimental data. In particular the effect of the temperature ramp on the light-off curve and reaction zone development is examined. An analysis of the C3H6 conversion is given in the third section while the final section examines the accuracy of the light-off curves which are produced when both CO and C3H6 are present in the feed gas. The analysis shows that the heat and mass transfer calculations provided reliable predictions of the warm-up behaviour and post light-off gas concentration profiles. The self-inhibition and cross-inhibition terms in the global rate expressions were also found to be reasonably reliable although the surface reaction rates required calibration with experimental data.

Influence of Manufacturing Tolerance on Aircraft Direct Operating Cost (DOC)

The influence of manufacturing tolerance on direct operating cost (DOC) is extrapolated from an engine nacelle to be representative of an entire aircraft body. Initial manufacturing tolerance data was obtained from the shop floor at Bombardier Aerospace Shorts, Belfast while the corresponding costs were calculated according to various recurring elements such as basic labour and overtime labour, rework, concessions, and redeployment; along with the non-recurrent costs due to tooling and machinery, etc. The relation of tolerance to cost was modelled statistically so that the cost impact of tolerance change could be ascertained. It was shown that a relatively small relaxation in the assembly and fabrication tolerances of the wetted surfaces resulted in reduced costs of production that lowered aircraft DOC, as the incurred drag penalty was predicted and taken into account during the optimisation process.