Evaluation of inductively coupled plasma mass spectrometry for determining Ca, Cu, Fe, Mg, Mn, Se and Zn in bovine semen samples using a simple sample dilution method

A simple and fast method for the determination of Ca, Cu, Fe, Mg, Mn, Se and Zn in bovine semen by quadrupole inductively coupled plasma spectrometry (q-ICP-MS) is described. Prior to analysis, samples (200 µL) were diluted 1:50 in a solution containing 0.01% v/v Triton® X-100 and 0.5% v/v nitric acid and directly analyzed by ICP-MS. The limits of detection of the method are 0.3, 0.03, 0.2, 0.04, 0.04, 0.03 and 0.03 µg L-1 for 44Ca, 63Cu, 57Fe, 24Mg, 64Zn, 82Se and 55Mn, respectively. For purposes of comparison and method validation, four ordinary bovine semen samples were directly analyzed by ICP-MS and by flame atomic absorption spectrometry (FAAS) or graphite furnace atomic absorption spectrometry (GF AAS), with no statistical difference between the techniques at the 95% level when applying the t-test. Then, the proposed method was applied in the determinations of Ca, Cu, Fe, Mg, Mn, Se and Zn in collected samples of bovine semen from different breeds, which are used in reproduction programs and artificial insemination.

Endothelial function in pre-pubertal children at risk of developing cardiomyopathy: a new frontier

Although it is known that obesity, diabetes, and Kawasaki's disease play important roles in systemic inflammation and in the development of both endothelial dysfunction and cardiomyopathy, there is a lack of data regarding the endothelial function of pre-pubertal children suffering from cardiomyopathy. In this study, we performed a systematic review of the literature on pre-pubertal children at risk of developing cardiomyopathy to assess the endothelial function of pre-pubertal children at risk of developing cardiomyopathy. We searched the published literature indexed in PubMed, Bireme and SciELO using the keywords 'endothelial', 'children', 'pediatric' and 'infant' and then compiled a systematic review. The end points were age, the pubertal stage, sex differences, the method used for the endothelial evaluation and the endothelial values themselves. No studies on children with cardiomyopathy were found. Only 11 papers were selected for our complete analysis, where these included reports on the flow-mediated percentage dilatation, the values of which were 9.80±1.80, 5.90±1.29, 4.50±0.70, and 7.10±1.27 for healthy, obese, diabetic and pre-pubertal children with Kawasaki's disease, respectively. There was no significant difference in the dilatation, independent of the endothelium, either among the groups or between the genders for both of the measurements in children; similar results have been found in adolescents and adults. The endothelial function in cardiomyopathic children remains unclear because of the lack of data; nevertheless, the known dysfunctions in children with obesity, type 1 diabetes and Kawasaki's disease may influence the severity of the cardiovascular symptoms, the prognosis, and the mortality rate. The results of this study encourage future research into the consequences of endothelial dysfunction in pre-pubertal children.

Width of buccal and posterior corridors: differences between cases treated with asymmetric and symmetric extractions

OBJECTIVE: To verify if there is difference in the buccal and posterior corridor width in cases treated with extraction of one and four premolars. METHODS: Through posed smile photographs of 23 Class II patients, subdivision, treated with extraction of one premolar and 25 Class I and Class II patients, subdivision, treated with extraction of four premolars, the percentage of buccal and posterior corridor width was calculated. The two protocols of extractions were compared regarding the buccal and posterior corridor width by independent t tests. RESULTS: There was no statistically significant difference on the buccal and posterior corridor widths between patients treated with symmetric and asymmetric extraction. CONCLUSION: The buccal and posterior corridor did not differ between the evaluated protocols of extractions.

Hydroxocobalamin quantification in human plasma by high-performance liquid chromatography coupled with electrospray tandem mass spectrometry in a pharmacokinetic study

A rapid, sensitive and specific method for quantifying hydroxocobalamin in human plasma using paracetamol as the internal standard (IS) is described. The analyte and the IS were extracted from plasma by liquid-liquid extraction using an organic solvent (ethanol 100%; -20°C). The extracts were analyzed by high performance liquid chromatography coupled with electrospray tandem mass spectrometry (HPLC-MS-MS). Chromatography was performed on Prevail C8 3 μm, analytical column (2.1×100 mm i.d.). The method had a chromatographic run time of 3.4 min and a linear calibration curve over the range 5-400 ng.mL-1 (r>0.9983). The limit of quantification was 5 ng.mL-1. The method was also validated without the use of the internal standard. The precision in the intra-batch validation with IS was 9.6%, 8.9%, 1.0% and 2.8% whereas without IS was 9.2%, 8.2%, 1.8% and 1.5% for 5, 15, 80 and 320 ng/mL, respectively. The accuracy in intra-batch validation with IS was 108.9%, 99.9%, 98.9% and 99.0% whereas without IS was 101.1%, 99.3%, 97.5% and 92.5% for 5, 15, 80 and 320 ng/mL, respectively. The precision in the inter-batch validation with IS was 9.4%, 6.9%, 4.6% and 5.5% whereas without IS was 10.9%, 6.4%, 5.0% and 6.2% for 5, 15, 80 and 320 ng/mL, respectively. The accuracy in inter-batch validation with IS was 101.9%, 104.1%, 103.2% and 99.7% whereas without IS was 94.4%, 101.2%, 101.6% and 96.0% for 5, 15, 80 and 320 ng/mL, respectively. This HPLC-MS-MS procedure was used to assess the pharmacokinetics of Hydroxo cobalamin following intramuscular injection 5000 μg in healthy volunteers of both sexes (10 males and 10 females). The volunteers had the following clinical characteristics (according to gender and expressed as mean ± SD [range]): males: age: 32.40 ± 8.00 y [23.00-46.00], height: 1.73 ± 0.07 m [1.62-1.85], body weight: 72.48 ± 10.22 Kg [60.20- 88.00]; females: age: 28.60 ± 9.54 y [18.00-44.00], height: 1.60 ± 0.05 m [1.54-1.70], body weight: 58.64 ± 6.09 Kg [51.70- 66.70]. The following pharmacokinetic parameters were obtained from the hydroxocobalamin plasma concentration vs. time curves: AUClast, T1/2, Tmax, Vd, Cl, Cmax and Clast. The pharmacokinetic parameters were 120 (± 25) ng/mL for Cmax, 2044 (± 641) ng.h/mL for AUClast, 8 (± 3.2) ng.mL-1 for Clast, 38 (± 15.8) hr for T1/2 and 2.5 (range 1-6) hr for Tmax. Female volunteers presented significant (p=0.0136) lower AUC (1706 ± 704) ng.h/mL) and larger (p=0.0205) clearance (2.91 ± 1.41 L/hr), as compared to male 2383 ± 343 ng.h/mL and 1.76 ± 0.23 L/hr, respectively. These pharmacokinetic differences could explain the higher prevalence of vitamin B12 deficiency in female patients. The method described validated well without the use of the internal standard and this approach should be investigated in other HPLC-MS-MS methods.

Sviluppo di metodologie di localizzazione nel contesto del Comprehensive Nuclear Test-Ban Treaty

Since the first underground nuclear explosion, carried out in 1958, the analysis of seismic signals generated by these sources has allowed seismologists to refine the travel times of seismic waves through the Earth and to verify the accuracy of the location algorithms (the ground truth for these sources was often known). Long international negotiates have been devoted to limit the proliferation and testing of nuclear weapons. In particular the Treaty for the comprehensive nuclear test ban (CTBT), was opened to signatures in 1996, though, even if it has been signed by 178 States, has not yet entered into force, The Treaty underlines the fundamental role of the seismological observations to verify its compliance, by detecting and locating seismic events, and identifying the nature of their sources. A precise definition of the hypocentral parameters represents the first step to discriminate whether a given seismic event is natural or not. In case that a specific event is retained suspicious by the majority of the State Parties, the Treaty contains provisions for conducting an on-site inspection (OSI) in the area surrounding the epicenter of the event, located through the International Monitoring System (IMS) of the CTBT Organization. An OSI is supposed to include the use of passive seismic techniques in the area of the suspected clandestine underground nuclear test. In fact, high quality seismological systems are thought to be capable to detect and locate very weak aftershocks triggered by underground nuclear explosions in the first days or weeks following the test. This PhD thesis deals with the development of two different seismic location techniques: the first one, known as the double difference joint hypocenter determination (DDJHD) technique, is aimed at locating closely spaced events at a global scale. The locations obtained by this method are characterized by a high relative accuracy, although the absolute location of the whole cluster remains uncertain. We eliminate this problem introducing a priori information: the known location of a selected event. The second technique concerns the reliable estimates of back azimuth and apparent velocity of seismic waves from local events of very low magnitude recorded by a trypartite array at a very local scale. For the two above-mentioned techniques, we have used the crosscorrelation technique among digital waveforms in order to minimize the errors linked with incorrect phase picking. The cross-correlation method relies on the similarity between waveforms of a pair of events at the same station, at the global scale, and on the similarity between waveforms of the same event at two different sensors of the try-partite array, at the local scale. After preliminary tests on the reliability of our location techniques based on simulations, we have applied both methodologies to real seismic events. The DDJHD technique has been applied to a seismic sequence occurred in the Turkey-Iran border region, using the data recorded by the IMS. At the beginning, the algorithm was applied to the differences among the original arrival times of the P phases, so the cross-correlation was not used. We have obtained that the relevant geometrical spreading, noticeable in the standard locations (namely the locations produced by the analysts of the International Data Center (IDC) of the CTBT Organization, assumed as our reference), has been considerably reduced by the application of our technique. This is what we expected, since the methodology has been applied to a sequence of events for which we can suppose a real closeness among the hypocenters, belonging to the same seismic structure. Our results point out the main advantage of this methodology: the systematic errors affecting the arrival times have been removed or at least reduced. The introduction of the cross-correlation has not brought evident improvements to our results: the two sets of locations (without and with the application of the cross-correlation technique) are very similar to each other. This can be commented saying that the use of the crosscorrelation has not substantially improved the precision of the manual pickings. Probably the pickings reported by the IDC are good enough to make the random picking error less important than the systematic error on travel times. As a further justification for the scarce quality of the results given by the cross-correlation, it should be remarked that the events included in our data set don’t have generally a good signal to noise ratio (SNR): the selected sequence is composed of weak events ( magnitude 4 or smaller) and the signals are strongly attenuated because of the large distance between the stations and the hypocentral area. In the local scale, in addition to the cross-correlation, we have performed a signal interpolation in order to improve the time resolution. The algorithm so developed has been applied to the data collected during an experiment carried out in Israel between 1998 and 1999. The results pointed out the following relevant conclusions: a) it is necessary to correlate waveform segments corresponding to the same seismic phases; b) it is not essential to select the exact first arrivals; and c) relevant information can be also obtained from the maximum amplitude wavelet of the waveforms (particularly in bad SNR conditions). Another remarkable point of our procedure is that its application doesn’t demand a long time to process the data, and therefore the user can immediately check the results. During a field survey, such feature will make possible a quasi real-time check allowing the immediate optimization of the array geometry, if so suggested by the results at an early stage.

Trasmission and Reflection (ATR)Far-Infrared Spectroscopy Applied in the Analysis of Cultural Heritage Materials

FIR spectroscopy is an alternative way of collecting spectra of many inorganic pigments and corrosion products found on art objects, which is not normally observed in the MIR region. Most FIR spectra are traditionally collected in transmission mode but as a real novelty it is now also possible to record FIR spectra in ATR (Attenuated Total Reflectance) mode. In FIR transmission we employ polyethylene (PE) for preparation of pellets by embedding the sample in PE. Unfortunately, the preparation requires heating of the PE in order to produces at transparent pellet. This will affect compounds with low melting points, especially those with structurally incorporated water. Another option in FIR transmission is the use of thin films. We test the use of polyethylene thin film (PETF), both commercial and laboratory-made PETF. ATR collection of samples is possible in both the MIR and FIR region on solid, powdery or liquid samples. Changing from the MIR to the FIR region is easy as it simply requires the change of detector and beamsplitter (which can be performed within a few minutes). No preparation of the sample is necessary, which is a huge advantage over the PE transmission method. The most obvious difference, when comparing transmission with ATR, is the distortion of band shape (which appears asymmetrical in the lower wavenumber region) and intensity differences. However, the biggest difference can be the shift of strong absorbing bands moving to lower wavenumbers in ATR mode. The sometimes huge band shift necessitates the collection of standard library spectra in both FIR transmission and ATR modes, provided these two methods of collecting are to be employed for analyses of unknown samples. Standard samples of 150 pigment and corrosion compounds are thus collected in both FIR transmission and ATR mode in order to build up a digital library of spectra for comparison with unknown samples. XRD, XRF and Raman spectroscopy assists us in confirming the purity or impurity of our standard samples. 24 didactic test tables, with known pigment and binder painted on the surface of a limestone tablet, are used for testing the established library and different ways of collecting in ATR and transmission mode. In ATR, micro samples are scratched from the surface and examined in both the MIR and FIR region. Additionally, direct surface contact of the didactic tablets with the ATR crystal are tested together with water enhanced surface contact. In FIR transmission we compare the powder from our test tablet on the laboratory PETF and embedded in PE. We also compare the PE pellets collected using a 4x beam condenser, focusing the IR beam area from 8 mm to 2 mm. A few samples collected from a mural painting in a Nepalese temple, corrosion products collected from archaeological Chinese bronze objects and samples from a mural paintings in an Italian abbey, are examined by ATR or transmission spectroscopy.

Machine learning methods for prediction of disulphide bonding states of cysteine residues in proteins

The goal of this thesis work is to develop a computational method based on machine learning techniques for predicting disulfide-bonding states of cysteine residues in proteins, which is a sub-problem of a bigger and yet unsolved problem of protein structure prediction. Improvement in the prediction of disulfide bonding states of cysteine residues will help in putting a constraint in the three dimensional (3D) space of the respective protein structure, and thus will eventually help in the prediction of 3D structure of proteins. Results of this work will have direct implications in site-directed mutational studies of proteins, proteins engineering and the problem of protein folding. We have used a combination of Artificial Neural Network (ANN) and Hidden Markov Model (HMM), the so-called Hidden Neural Network (HNN) as a machine learning technique to develop our prediction method. By using different global and local features of proteins (specifically profiles, parity of cysteine residues, average cysteine conservation, correlated mutation, sub-cellular localization, and signal peptide) as inputs and considering Eukaryotes and Prokaryotes separately we have reached to a remarkable accuracy of 94% on cysteine basis for both Eukaryotic and Prokaryotic datasets, and an accuracy of 90% and 93% on protein basis for Eukaryotic dataset and Prokaryotic dataset respectively. These accuracies are best so far ever reached by any existing prediction methods, and thus our prediction method has outperformed all the previously developed approaches and therefore is more reliable. Most interesting part of this thesis work is the differences in the prediction performances of Eukaryotes and Prokaryotes at the basic level of input coding when ‘profile’ information was given as input to our prediction method. And one of the reasons for this we discover is the difference in the amino acid composition of the local environment of bonded and free cysteine residues in Eukaryotes and Prokaryotes. Eukaryotic bonded cysteine examples have a ‘symmetric-cysteine-rich’ environment, where as Prokaryotic bonded examples lack it.

Calcolo della posizione di reti di stazioni permanenti

Con il trascorrere del tempo, le reti di stazioni permanenti GNSS (Global Navigation Satellite System) divengono sempre più un valido supporto alle tecniche di rilevamento satellitare. Esse sono al tempo stesso un’efficace materializzazione del sistema di riferimento e un utile ausilio ad applicazioni di rilevamento topografico e di monitoraggio per il controllo di deformazioni. Alle ormai classiche applicazioni statiche in post-processamento, si affiancano le misure in tempo reale sempre più utilizzate e richieste dall’utenza professionale. In tutti i casi risulta molto importante la determinazione di coordinate precise per le stazioni permanenti, al punto che si è deciso di effettuarla tramite differenti ambienti di calcolo. Sono stati confrontati il Bernese, il Gamit (che condividono l’approccio differenziato) e il Gipsy (che utilizza l’approccio indifferenziato). L’uso di tre software ha reso indispensabile l’individuazione di una strategia di calcolo comune in grado di garantire che, i dati ancillari e i parametri fisici adottati, non costituiscano fonte di diversificazione tra le soluzioni ottenute. L’analisi di reti di dimensioni nazionali oppure di reti locali per lunghi intervalli di tempo, comporta il processamento di migliaia se non decine di migliaia di file; a ciò si aggiunge che, talora a causa di banali errori, oppure al fine di elaborare test scientifici, spesso risulta necessario reiterare le elaborazioni. Molte risorse sono quindi state investite nella messa a punto di procedure automatiche finalizzate, da un lato alla preparazione degli archivi e dall’altro all’analisi dei risultati e al loro confronto qualora si sia in possesso di più soluzioni. Dette procedure sono state sviluppate elaborando i dataset più significativi messi a disposizione del DISTART (Dipartimento di Ingegneria delle Strutture, dei Trasporti, delle Acque, del Rilevamento del Territorio - Università di Bologna). E’ stato così possibile, al tempo stesso, calcolare la posizione delle stazioni permanenti di alcune importanti reti locali e nazionali e confrontare taluni fra i più importanti codici scientifici che assolvono a tale funzione. Per quanto attiene il confronto fra i diversi software si è verificato che: • le soluzioni ottenute dal Bernese e da Gamit (i due software differenziati) sono sempre in perfetto accordo; • le soluzioni Gipsy (che utilizza il metodo indifferenziato) risultano, quasi sempre, leggermente più disperse rispetto a quelle degli altri software e mostrano talvolta delle apprezzabili differenze numeriche rispetto alle altre soluzioni, soprattutto per quanto attiene la coordinata Est; le differenze sono però contenute in pochi millimetri e le rette che descrivono i trend sono comunque praticamente parallele a quelle degli altri due codici; • il citato bias in Est tra Gipsy e le soluzioni differenziate, è più evidente in presenza di determinate combinazioni Antenna/Radome e sembra essere legato all’uso delle calibrazioni assolute da parte dei diversi software. E’ necessario altresì considerare che Gipsy è sensibilmente più veloce dei codici differenziati e soprattutto che, con la procedura indifferenziata, il file di ciascuna stazione di ciascun giorno, viene elaborato indipendentemente dagli altri, con evidente maggior elasticità di gestione: se si individua un errore strumentale su di una singola stazione o se si decide di aggiungere o togliere una stazione dalla rete, non risulta necessario il ricalcolo dell’intera rete. Insieme alle altre reti è stato possibile analizzare la Rete Dinamica Nazionale (RDN), non solo i 28 giorni che hanno dato luogo alla sua prima definizione, bensì anche ulteriori quattro intervalli temporali di 28 giorni, intercalati di sei mesi e che coprono quindi un intervallo temporale complessivo pari a due anni. Si è così potuto verificare che la RDN può essere utilizzata per l’inserimento in ITRF05 (International Terrestrial Reference Frame) di una qualsiasi rete regionale italiana nonostante l’intervallo temporale ancora limitato. Da un lato sono state stimate le velocità ITRF (puramente indicative e non ufficiali) delle stazioni RDN e, dall’altro, è stata effettuata una prova di inquadramento di una rete regionale in ITRF, tramite RDN, e si è verificato che non si hanno differenze apprezzabili rispetto all’inquadramento in ITRF, tramite un congruo numero di stazioni IGS/EUREF (International GNSS Service / European REference Frame, SubCommission for Europe dello International Association of Geodesy).

Untersuchungen zur Visuomotorik des Menschen

Motorische Bewegungen werden über die visuelle Rückmeldung auf ihre Genauigkeit kontrolliert und ggf. korrigiert. Über einen technischen Eingriff, wie beispielsweise einer Prismenbrille, kann man eine Differenz zwischen optisch wahrgenommener und haptisch erlebter Umwelt erzeugen, um die Fähigkeiten des visuomotorischen Systems zu testen. In dieser Arbeit wurde eine computergestützte Methode entwickelt, eine solche visuomotorische Differenz zu simulieren. Die Versuchspersonen führen eine ballistische Bewegung mit Arm und Hand aus in der Absicht, ein vorgegebenes Ziel zu treffen. Die Trefferpunkte werden durch einen Computer mit Hilfe eines Digitalisierungstablettes aufgenommen. Die visuelle Umwelt, welche den Versuchspersonen präsentiert wird, ist auf einem Monitor dargestellt. Das Monitorabbild – ein Kreuz auf weißem Hintergrund – betrachten die Testpersonen über einen Spiegel. Dieser ist in einem entsprechenden Winkel zwischen Monitor und Digitalisierungstablett angebracht, so dass das Zielbild auf dem Digitalisierungstablett projiziert wird. Die Testpersonen nehmen das Zielkreuz auf dem Digitalisierungstablett liegend wahr. Führt die Versuchsperson eine Zielbewegung aus, können die aufgenommenen Koordinaten als Punkte auf dem Monitor dargestellt werden und die Testperson erhält über diese Punktanzeige ein visuelles Feedback ihrer Bewegung. Der Arbeitsbereich des Digitalisierungstabletts kann über den Computer eingerichtet und so motorische Verschiebungen simuliert werden. Die verschiedenartigen Möglichkeiten dieses Aufbaus wurden zum Teil in Vorversuchen getestet um Fragestellungen, Methodik und technische Einrichtungen aufeinander abzustimmen. Den Hauptversuchen galt besonderes Interesse an der zeitlichen Verzögerung des visuellen Feedbacks sowie dem intermanuellen Transfer. Hierbei ergaben sich folgende Ergebnisse: ● Die Versuchspersonen adaptieren an eine räumlich verschobene Umwelt. Der Adaptationsverlauf lässt sich mit einer Exponentialfunktion mathematisch berechnen und darstellen. ● Dieser Verlauf ist unabhängig von der Art des visuellen Feedbacks. Die Beobachtung der Handbewegung während der Adaptation zeigt die gleiche Zielabfolge wie eine einfache Punktprojektion, die den Trefferort der Bewegung darstellt. ● Der exponentielle Verlauf der Adaptationsbewegung ist unabhängig von den getesteten zeitlichen Verzögerungen des visuellen Feedbacks. ● Die Ergebnisse des Folgeeffektes zeigen, dass bei zunehmender zeitlicher Verzögerung des visuellen Feedbacks während der Adaptationsphase, die Größe des Folgeeffektwertes geringer wird, d.h. die anhaltende Anpassungsleistung an eine visuomotorische Differenz sinkt. ● Die Folgeeffekte weisen individuelle Eigenheiten auf. Die Testpersonen adaptieren verschieden stark an eine simulierte Verschiebung. Ein Vergleich mit den visuomotorischen Herausforderungen im Vorleben der Versuchspersonen ließ vermuten, dass das visuomotorische System des Menschen trainierbar ist und sich - je nach Trainingszustand – unterschiedlich an wahrgenommene Differenzen anpasst. ● Der intermanuelle Transfer konnte unter verschiedenen Bedingungen nachgewiesen werden. ● Ein deutlich stärkerer Folgeeffekt kann beobachtet werden, wenn die wahrgenommene visuomotorische Differenz zwischen Ziel und Trefferpunkt in eine Gehirnhälfte projiziert wird und der Folgeeffekt mit der Hand erfolgt, welche von dieser Hirnhemisphäre gesteuert wird. Der intermanuelle Transfer wird demnach begünstigt, wenn die visuelle Projektion der Fehlerbeobachtung in die Gehirnhälfte erfolgt, die während der Adaptationsphase motorisch passiv ist.

Spin polarised Heusler compounds

In der vorliegenden Dissertation dient ein einfaches Konzept zur Systematisierung der Suche nach neuen Materialien mit hoher Spinpolarisation. Dieses Konzept basiert auf zwei semi-empirischen Modellen. Zum einen kann die Slater-Pauling Regel zur Abschätzung magnetischer Momente verwendet werden. Dieses Modell wird dabei durch Rechnungen zur elektronischen Struktur unterstützt. Das zweites Modell kann insbesondere für die Co2YZ Heusler Verbindungen beim Vergleich ihrer magnetischen Eigenschaften gefunden werden. Für diese Verbindungen ergibt sich eine scheinbare lineare Abhängigkeit der Curie-Temperatur beim Auftragen als Funktion des magnetischen Momentes. Angeregt durch diese Modelle wurde die Heusler Verbindung Co2FeSi nochmals detailliert im Hinblick auf ihre geometrische und magnetische Struktur hin untersucht. Als Methoden dienten dabei die Pulver-Röntgenbeugung, die EXAFS Spektroskopie, Röntgen Absorptions- and Mößbauer Spektroskopie sowie Hoch- und Tieftemperatur Magnetometrie, XMCD and DSC. Die Messungen zeigten, dass es sich bei Co2FeSi um das Material mit dem höchsten magnetischen Moment (6 B) und der höchsten Curie Temperatur (1100 K) sowohl in der Klasse der Heusler Verbindungen als auch in der Klasse der halbmetallischen Ferromagnete handelt. Zusätzlich werden alle experimentellen Ergebnisse durch detaillierte Rechnungen zur elektronischen Struktur unterstützt. Die gleichen Konzepte wurden verwendet, um die Eigenschaften der Heusler Verbindung Co2Cr1-xFexAl vorherzusagen. Die elektronische Struktur und die spektroskopischen Eigenschaften wurden mit der voll-relativistischen Korringa-Kohn-Rostocker Methode berechnet, unter Verwendung kohärenter Potentialnäherungen um der zufälligen Verteilung von Cr und Fe Atomen sowie zufälliger Unordnung Rechnung zu tragen. Magnetische Effekte wurden durch die Verwendung Spin-abhängiger Potentiale im Rahmen der lokalen Spin-Dichte-Näherung mit eingeschlossen. Die strukturellen und chemischen Eigenschaften der quaternären Heusler Verbindung Co2Cr1-xFexAl wurden an Pulver und Bulkproben gemessen. Die Fernordnung wurde mit der Pulver Röntgenbeugung und Neutronenbeugung untersucht, während die Nahordnung mit der EXAFS Spektroskopie aufgeklärt wurde. Die magnetische Struktur von Pulver und Bulkproben wurde mitttels 57Fe-Mößbauer Spektroskopie gemessen. Die chemische Zusammensetzung wurde durch XPS analysiert. Die Ergebnisse dieser Methoden wurden verglichen, um eine Einsicht in die Unterschiede zwischen Oberflächen und Volumeneigenschaften zu erlangen sowie in das Auftreten von Fehlordnung in solchen Verbindungen. Zusätzlich wurde XMCD an den L3,2 Kanten von Co, Fe, and Cr gemessen, um die elementspezifischen magnetischen Momente zu bestimmen. Rechnungen und Messungen zeigen dabei eine Zunahme des magnetischen Momentes bei steigendem Fe-Anteil. Resonante Photoemission mit weicher Röntgenstrahlung sowie Hochenergie Photoemission mit harter Röntgenstrahlung wurden verwendet, um die Zustandsdichte der besetzten Zustände in Co2Cr0.6Fe0.4Al zu untersuchen. Diese Arbeit stellt außerdem eine weitere, neue Verbindung aus der Klasse der Heusler Verbindungen vor. Co2CrIn ist L21 geordnet, wie Messungen mittels Pulver Röntgenbeugung zeigen. Die magnetischen Eigenschaften wurden mit magnetometrisch bestimmt. Co2CrIn ist weichmagnetisch mit einer Sättigungsmagnetisierung von 1.2B bei 5 K. Im Gegensatz zu den bereits oben erwähnten Co2YZ Heusler Verbindungen ist Co2CrIn kein halbmetallischer Ferromagnet. Im Rahmen dieser Arbeit wird weiterhin eine Regel zur Vorhersage von halbmetallischen komplett kompensierten Ferrimagneten in der Klasse der Heusler Verbindungen vorgestellt. Dieses Konzept resultiert aus der Kombination der Slater-Pauling Regel mit der Kübler-Regel. Die Kübler Regel besagt, dass Mn auf der Y Position zu einem hoch lokalisierten magnetischen Moment tendiert. Unter Verwendung dieses neuen Konzeptes werden für einige Kandidaten in der Klasse der Heusler Verbindungen die Eigenschaft des halbmetallischen komplett kompensierten Ferrimagnetismus vorhergesagt. Die Anwendung dieses Konzeptes wird anhand von Rechnungen zur elektronischen Struktur bestätigt.

A Phase Space Box-counting based Method for Arrhythmia Prediction from Electrocardiogram Time Series

Arrhythmia is one kind of cardiovascular diseases that give rise to the number of deaths and potentially yields immedicable danger. Arrhythmia is a life threatening condition originating from disorganized propagation of electrical signals in heart resulting in desynchronization among different chambers of the heart. Fundamentally, the synchronization process means that the phase relationship of electrical activities between the chambers remains coherent, maintaining a constant phase difference over time. If desynchronization occurs due to arrhythmia, the coherent phase relationship breaks down resulting in chaotic rhythm affecting the regular pumping mechanism of heart. This phenomenon was explored by using the phase space reconstruction technique which is a standard analysis technique of time series data generated from nonlinear dynamical system. In this project a novel index is presented for predicting the onset of ventricular arrhythmias. Analysis of continuously captured long-term ECG data recordings was conducted up to the onset of arrhythmia by the phase space reconstruction method, obtaining 2-dimensional images, analysed by the box counting method. The method was tested using the ECG data set of three different kinds including normal (NR), Ventricular Tachycardia (VT), Ventricular Fibrillation (VF), extracted from the Physionet ECG database. Statistical measures like mean (μ), standard deviation (σ) and coefficient of variation (σ/μ) for the box-counting in phase space diagrams are derived for a sliding window of 10 beats of ECG signal. From the results of these statistical analyses, a threshold was derived as an upper bound of Coefficient of Variation (CV) for box-counting of ECG phase portraits which is capable of reliably predicting the impeding arrhythmia long before its actual occurrence. As future work of research, it was planned to validate this prediction tool over a wider population of patients affected by different kind of arrhythmia, like atrial fibrillation, bundle and brunch block, and set different thresholds for them, in order to confirm its clinical applicability.

The factorization method for real elliptic problems

The Factorization Method localizes inclusions inside a body from measurements on its surface. Without a priori knowing the physical parameters inside the inclusions, the points belonging to them can be characterized using the range of an auxiliary operator. The method relies on a range characterization that relates the range of the auxiliary operator to the measurements and is only known for very particular applications. In this work we develop a general framework for the method by considering symmetric and coercive operators between abstract Hilbert spaces. We show that the important range characterization holds if the difference between the inclusions and the background medium satisfies a coerciveness condition which can immediately be translated into a condition on the coefficients of a given real elliptic problem. We demonstrate how several known applications of the Factorization Method are covered by our general results and deduce the range characterization for a new example in linear elasticity.

Novel isolates of Cydia pomonella granulovirus (CpGV): deciphering the molecular mechanism for overcoming CpGV resistance in codling moth (Cydia pomonella)

During the last twenty years, Cydia pomonolla granulovirus (CpGV, Baculoviridae) has become the most important biological control agent for the codling moth (CM) in organic and integrated apple production. All registered products in Europe are based on the isolate CpGV-M, which was discovered 1964 in Mexico. A serious threat to future application of CpGV is the occurrence of CM field populations resistant to CpGV. Since 2003, populations with up to 10,000-fold reduced susceptibility were reported from orchards in Germany, France, Italy, Switzerland, Austria and the Netherlands. A putative alternative to CpGV-M are novel CpGV isolates which are able to overcome CM resistance. This thesis focuses on the identification and characterisation of resistance overcoming CpGV isolates and the analysis of their molecular difference to CpGV-M.rnSixteen CpGV isolates were tested against CM lab strains in bioassays. Hereby, five isolates were identified which were able to completely overcome resistance. The genomes of these isolates were compared to CpGV-M by restriction fragment length polymorphism (RFLP) analysis. To identify the molecular factor responsible for improved virulence of some CpGV isolates, major genomic differences were sequenced and analysed. A 0.7 kb insertion was found in CpGV-I01, -I12 and -E2, but not in other resistance overcoming isolates. Analysis of the insertions sequence revealed that it might be due to a transposition event, but not involved in overcoming resistance. rnFor unequivocal identification of CpGV isolates, a new method based on molecular analysis was established. Partial sequencing of the conserved polyhedrin/granulin (polh/gran), late expression factor-8 (lef-8) and late expression factor-9 (lef-9) genes revealed single nucleotide polymorphisms (SNPs). SNP analysis correlated with the grouping obtained by RFLP analysis. A phylogenetic classification due to different genome types A-E is proposed. Phylogenetic analysis suggested that CpGV-M was the phylogenetically youngest of the tested CpGV isolates.rnWhole genome sequencing of two resistance overcoming isolates CpGV-I12 (type D genome) and -S (type E genome) and CpGV-M (type A genome) was performed. Comparison of the three genomes revealed a high sequence identity. Several insertions and deletions ranging from 1-700 nucleotides (nt) were found. Comparison on open reading frame (ORF) level revealed that CpGV-I12 and -S shared only one protein alteration when compared to CpGV-M: a stretch of 24 nt present in ORF cp24 was not found in any of the resistance overcoming isolates. Cp24 codes for the early gene pe38. Combined with the results of phylogenetic analysis, it is proposed that these 24 nt are a recent insertion into the CpGV-M genome. The role of pe38 in overcoming resistance was investigated by knocking out pe38 of a CpGV-M based bacmid and swapping of CpGV-I12 pe38 of into the k.o. bacmid. When pe38 of CpGV-I12 was inserted into the k.o. bacmid, the infectivity could not be rescued, suggesting that the genomic portion of pe38 might play a role in its function.rnIt can be concluded that the recently observed CpGV resistance in CM is only related to type A genomes. RFLP and SNP analysis provide tools for identifying and characterising different CpGV isolates reliably, a pre-condition for a future registration of CpGV products based on novel CpGV isolates.rnrnrn

A new method for the estimation of the reverberation time from measured room impulse responses with application to Italian opera houses

The Schroeder's backward integration method is the most used method to extract the decay curve of an acoustic impulse response and to calculate the reverberation time from this curve. In the literature the limits and the possible improvements of this method are widely discussed. In this work a new method is proposed for the evaluation of the energy decay curve. The new method has been implemented in a Matlab toolbox. Its performance has been tested versus the most accredited literature method. The values of EDT and reverberation time extracted from the energy decay curves calculated with both methods have been compared in terms of the values themselves and in terms of their statistical representativeness. The main case study consists of nine Italian historical theatres in which acoustical measurements were performed. The comparison of the two extraction methods has also been applied to a critical case, i.e. the structural impulse responses of some building elements. The comparison underlines that both methods return a comparable value of the T30. Decreasing the range of evaluation, they reveal increasing differences; in particular, the main differences are in the first part of the decay, where the EDT is evaluated. This is a consequence of the fact that the new method returns a “locally" defined energy decay curve, whereas the Schroeder's method accumulates energy from the tail to the beginning of the impulse response. Another characteristic of the new method for the energy decay extraction curve is its independence on the background noise estimation. Finally, a statistical analysis is performed on the T30 and EDT values calculated from the impulse responses measurements in the Italian historical theatres. The aim of this evaluation is to know whether a subset of measurements could be considered representative for a complete characterization of these opera houses.

Untersuchungen über ADAMTS13 in Gerinnungsfaktorpräparaten

Zusammenfassung rnIn der vorliegenden Arbeit wurden sechs VWF/FVIII Gerinnungsfaktorkonzentrate unterschiedlicher Chargen auf ihre ADAMTS13 Aktivität, Antigen und VWF Multimere untersucht. Grund dafür ist die Annahme, dass bei der Aufkonzentrierung des VWFs möglicherweise auch erhöhte Mengen an ADAMTS13 vorhanden sind. Wäre dies nachweisbar, könnten die entsprechenden Konzentrate auch Anwendung bei TTP Patienten finden. Neben den Gerinnungsfaktorkonzentraten wurden ebenfalls die zur Plasmapherese verwendeten Therapeutika FFP und s/d Plasma analysiert. Es soll getestet werden, ob Unterschiede hinsichtlich der Qualität zwischen den Präparaten bestehen und inwiefern die Blutgruppen eine Auswirkung auf die ADAMTS13 Aktivität/Antigen haben. Überdies wurde die Bedeutung von ADAMTS13 als wichtiges diagnostisches Merkmal im Rahmen der Gegenüberstellung von Patienten mit thrombotischen Mikroangiopathien erörtert. Alle angewandten Methoden wurden zudem kritisch miteinander verglichen und auf ihre Eignung für die klinische Diagnostik getestet. Zur Untersuchung der ADAMTS13 Aktivität kamen drei unterschiedliche Methoden zur Anwendung, die BCS-Methode nach Böhm und zwei FRET Kits (Technozym®ADAMTS13/ActifluorTMADAMTS13). Für die Bestimmung des ADAMTS13 Antigen wurde das Technozym®ADAMTS13 Kit verwendete als auch der Imubind®ELISA angewendet. Mittels der SDS-Gelelektrophorese konnten die VWF Multimere dargestellt werden. Die Untersuchungen konnten zeigen, dass nur in Haemate®P, deutlich höhere ADAMTS13 Aktivitäten (12,3% bzw. 470ng/ml) sowie ein physiologische Antigenwerte vorlagen. Die anderen Faktorkonzentrate wiesen entweder nur sehr geringe bzw. keine Aktivitäten auf. Das Antigen lag bei allen Konzentraten im nachweisbaren Bereich. Folglich ist ein Einsatz von Haemate®P bei der Therapie der TTP, insbesondere bei hereditären Formen sowie bei Kindern, die durch eine Plasmapherese stark belastet werden, und bei Schwangeren, könnten, in Erwägung zu ziehen und innerhalb der Klinik zu testen. Die Plasmapräparate FFP und Octaplas® wiesen in allen Untersuchungen ADAMTS13 Aktivitäten und Antigen im mittleren bis hohen physiologischen Bereich auf. Insbesondere bei Blutgruppe 0 ließ sich beiden Präparaten eine höhere ADAMTS13 Aktivität und Antigen gegenüber den drei anderen Blutgruppen darstellen. Insgesamt waren die interindividuellen Schwankungen bei FFP deutlich höher als bei Octaplas®, was sich in der unterschiedlichen Herstellung der Präparate begründen lässt. Octaplas® ist also genauso geeignet zur Plasmapherese bei der TTP wie FFP, kann jedoch aufgrund seiner intensiveren Virusinaktivierung eine größere Sicherheit aufweisen und stellt sich auch in der Klinik als nebenwirkungsärmer dar. Bei der Gegenüberstellung der thrombotischen Mikroangiopathien konnte gezeigt werden, dass eine verminderte ADAMTS13 Aktivität ein wichtiges Unterscheidungsmerkmal ist und auch während der Remission schon diagnostizierbar werden kann. Auf der Grundlage der labordiagnostischen Werte und dem klinischen Erscheinungsbild im akuten Schub und in der Remission konnte ein diagnostischer Algorithmus für den klinischen Alltag erstellt werden. In der Methodenvalidierung erwies sich der ActifluorTMADAMTS13 Kit als der beste Kit, da er innerhalb kürzester Zeit zuverlässige Werte in Standardeinheiten liefert. Nach neuesten Erkenntnissen, bei der eine Unterscheidung von ADAMTS13 Aktivitäten über und unter 5 % von großer prognostischer Bedeutung sind, ist die BCS-Methode nach Böhm mit einer unteren Nachweisgrenze von 6,2% zu ungenau und auch hinsichtlich ihres Zeitaufwandes eher ungünstig.rn