Spray visualisation and acoustic analysis in a gas-turbine type burner

This paper presents the characterisation of self-excited oscillations in a kerosene burner. The combustion instability exhibits two different modes and frequencies depending on the air flow rate. Experimental results reveal the influence of the spray to shift between these two modes. Pressure and heat release fluctuations have been measured simultaneously and the flame transfer function has been calculated from these measurements. The Mie scattering technique has been used to record spray fluctuations in reacting conditions with a high speed camera. Innovative image processing has enabled us to obtain fluctuations of the Mie scattered light from the spray as a temporal signal acquired simultaneously with pressure fluctuations. This has been used to determine a transfer function relating the image intensity and hence the spray fluctuations to changes in air velocity. This function has identified the different role the spray plays in the two modes of instability. At low air flow rates, the spray responds to an unsteady air flow rate and the time varying spray characteristics lead to unsteady combustion. At higher air flow rates, effective evaporation means that the spray dynamics are less important, leading to a different flame transfer function and frequency of self-excited oscillation. In conclusion, the combustion instabilities observed are closely related with the fluctuations of the spray motion and evaporation.

High sensitive NO2 gas sensor with low power consumption using selectively grown ZnO nanorods.

The noble gas sensor using multiple ZnO nanorods was fabricated with CMOS compatible process and sol-gel growth method on selective area and gas response characteristics to NO2 gas of the sensor device were investigated. We confirmed the sensors had high sensitive response denoted by the sensitivity of several tens for NO2 gas sensing and also showed pretty low power consumption close to 20 mW even though the recovery of resistance come up to almost the initial value.

Gas-phase production of gold-decorated silica nanoparticles.

Gold-decorated silica nanoparticles were synthesized in a two-step process in which silica nanoparticles were produced by chemical vapor synthesis using tetraethylorthosilicate (TEOS) and subsequently decorated using two different gas-phase evaporative techniques. Both evaporative processes resulted in gold decoration of the silica particles. This study compares the mechanisms of particle decoration for a production method in which the gas and particles remain cool to a method in which the entire aerosol is heated. Results of transmission electron microscopy and visible spectroscopy studies indicate that both methods produce particles with similar morphologies and nearly identical absorption spectra, with peak absorption at 500-550 nm. A study of the thermal stability of the particles using heated-TEM indicates that the gold decoration on the particle surface remains stable at temperatures below 900 °C, above which the gold decoration begins to both evaporate and coalesce.

牛耳草Bose hygrometrica 离体叶脱水-复水过程的光合作用及基因表达

本文以复苏植物牛耳草Boea hygrometrica成熟植株的离体叶片为试材，对比非复苏植物烟叶唇苣苔Chirita heterotricha, 以光合作用在脱水－复水过程中的变化为切入点，从生理水平上探讨其脱水保护位点：应用mRNA差异显示技术，从分子水平上探讨其脱水保护机制。 光合放氧速率、快速荧光诱导动力学、慢速荧光诱导动力学、荧光发射光谱、荧光激发谱的结果表明，相对于烟叶唇柱苣苔，脱水对牛耳草净光合速率、PS II和PS I光化学活性、电子传递、光合磷酸化及CO_2固定的影响有一个共同的特点，即脱水时迅速降低，复水后恢复能力强。通过非变性绿胶的研究牛耳草叶片类囊体膜叶绿素－蛋白复合体在脱水－复水过程中保持高度稳定。色素含量分析表明牛耳草的叶绿素含量在脱水－复水过程中也相对稳定。这些特征可能是牛耳草叶片光合作用脱水保护机制的一部分。 SDS－PAGE和IEF电泳结果表明，牛耳草脱水复苏过程中蛋白质表达有差异，或增或减，并分别发现了一条（SDS－PAGE）和两条（IEF）在脱水过程中特异出现的蛋白质。 本文以银染法代替放射自显影用于mRNA差异显示，不但简化了实验步骤，缩短了实验周期，而且在不降低灵敏度的前提下避免了放射性危害，降低了实验成本。本文证明了mRNA差异银染显示法用于复苏植物牛耳草脱水－复水过程中基因表达变化的研究是可行的。 mRNA差异银染显示法揭示牛耳草耐脱水复苏机制涉及到基因表达的调控。脱水－复水过程中差异表达的基因有6种，其中脱水特异诱导表达的13个cDNA所相应的基因、脱水上调节的15个cDNA所相应的基因可能参与牛耳草叶片脱水保护机制，复水特异诱导的8个cDNA的所相应基因可能参与牛耳草复水后的修复机制。2个脱水特异诱导表达的cDNA片段进行了克隆和测序。