V-CE Sensing for IGBT Protection in NPC Three Level Converters-Causes For Spurious Trippings and Their Elimination

Neutral point clamped (NPC), three level converters with insulated gate bipolar transistor devices are very popular in medium voltage, high power applications. DC bus short circuit protection is usually done, using the sensed voltage across collector and emitter (i.e., V-CE sensing), of all the devices in a leg. This feature is accommodated with the conventional gate drive circuits used in the two level converters. The similar gate drive circuit, when adopted for NPC three level converter protection, leads to false V-CE fault signals for inner devices of the leg. The paper explains the detailed circuit behavior and reasons, which result in the occurrence of such false V-CE fault signals. This paper also illustrates that such a phenomenon shows dependence on the power factor of the supplied three-phase load. Finally, experimental results are presented to support the analysis. It is shown that the problem can be avoided by blocking out the V-CE sense fault signals of the inner devices of the leg.

Synthesis, structure and redox properties of (?-oxo)bis(?-carboxylato)diruthenium(III) complexes containing three different terminal ligands

Blue coloured, unstable, essentially diamagnetic and non-electrolytic diruthenium(III) complexes of the formation [Ru2O(O2CR)4(en)2(PPh3)2] were prepared by reacting [Ru2O(O2CR)4(PPh3)2] with 1,2-diaminoethane (en) in CH2Cl2 (R = C6H4-p-X; X = H, Me and OMe). The molecular structure of the complexes is proposed as [{(?1-O2CR)(?1-en)(PPH3)Ru}2(?-O)(?-O2CR)2] based on the 1H NMR spectral data. The electronic spectra of the complexes display a band near 569 nm with a shoulder at 630 nm. In CH2Cl2-0.1 M [Bun4N]ClO4, the complexes exhibit redox couples Ru2III,III/Ru2III,IV and Ru2III,IV/Ru2IV,IV near 0.1 and 1.2 V (vs SCE), respectively. The potentials are the lowest among diruthenium(III) complexes with a similar core structure.

Decoupled three-dimensional finite element computation of thermoelastic damping using Zener's approximation

We consider three dimensional finite element computations of thermoelastic damping ratios of arbitrary bodies using Zener's approach. In our small-damping formulation, unlike existing fully coupled formulations, the calculation is split into three smaller parts. Of these, the first sub-calculation involves routine undamped modal analysis using ANSYS. The second sub-calculation takes the mode shape, and solves on the same mesh a periodic heat conduction problem. Finally, the damping coefficient is a volume integral, evaluated elementwise. In the only other decoupled three dimensional computation of thermoelastic damping reported in the literature, the heat conduction problem is solved much less efficiently, using a modal expansion. We provide numerical examples using some beam-like geometries, for which Zener's and similar formulas are valid. Among these we examine tapered beams, including the limiting case of a sharp tip. The latter's higher-mode damping ratios dramatically exceed those of a comparable uniform beam.

Barrier crossing in one and three dimensions by a long chain

We consider the Kramers problem for a long chain polymer trapped in a biased double-well potential. Initially the polymer is in the less stable well and it can escape from this well to the other well by the motion of its N beads across the barrier to attain the configuration having lower free energy. In one dimension we simulate the crossing and show that the results are in agreement with the kink mechanism suggested earlier. In three dimensions, it has not been possible to get an analytical `kink solution' for an arbitrary potential; however, one can assume the form of the solution of the nonlinear equation as a kink solution and then find a double-well potential in three dimensions. To verify the kink mechanism, simulations of the dynamics of a discrete Rouse polymer model in a double well in three dimensions are carried out. We find that the time of crossing is proportional to the chain length, which is in agreement with the results for the kink mechanism. The shape of the kink solution is also in agreement with the analytical solution in both one and three dimensions.

Cloning and characterization of a cluster of genes coding for 5S rRNA and three tRNAs from Azospirillum lipoferum

A genomic library was constructed from a HindIII digest of Azospirillum lipoferum chromosomal DNA in the HindIII site of pUC19. From the library, a clone, pALH64, which showed strong hybridization with 3' end labeled A. lipoferum total tRNAs and which contains a 2.9 kb insert was isolated and restriction map of the insert established. The nucleotide sequence of a 490 bp HindIII-HincII subfragment containing a cluster of genes coding for 5S rRNA, tRNA(Val)(UAC), tRNA(Thr)(UGA) and tRNA(Lys)(UUU) has been determined. The gene organization is 5S rRNA (115 bp), spacer (10 bp), tRNA(Val) (76 bp), spacer (3 bp), tRNA(Thr) (76 bp), spacer (7 bp) and tRNA(Lys) (76 bp). Hybridization experiments using A. lipoferum total tRNAs and 5S rRNA with the cloned DNA probes revealed that all three tRNA genes and the 5S rRNA gene are expressed in vivo in the bacterial cells.

Dynamic analysis of three point bend specimens under impact

A simple one dimensional inertial model is presented for transient response analysis of notched beams under impact, and extracting dynamic initiation toughness values. The model includes the effects of striker mass interactions, and contact deformations of the beam. Displacement time history of the striker mass is applied to the model as forcing function. The model is validated by comparison with the experimental investigation on ductile aluminium 6061 alloy and brittle polymer, PMMA.

Unsteady three-dimensional boundary layer flow due to a stretching surface

In this numerical study, the unsteady laminar incompressible boundary-layer flow over a continuously stretching surface has been investigated when the velocity of the stretching surface varies arbitrarily with time. Both the nodal and the saddle point regions of flow have been considered for the analysis. Also, constant wall temperature/concentration and constant heat/mass flux at the stretching surface have been taken into account. The quasilinearisation method with an implicit finite-difference scheme is used in the nodal point region (0 less-than-or-equal-to c less-than-or-equal-to 1) where c denotes the stretching ratio. This method fails in the saddle point region (-1 less-than-or-equal-to c less-than-or-equal-to 0) due to the occurrence of reverse flow in the y-component of velocity. In order to overcome this difficulty, the method of parametric differentiation with an implicit finite-difference scheme is used, where the values at c = 0 are taken as starting values. Results have been obtained for the stretching velocities which are accelerating and decelerating with time. Results show that the skin friction, the heat transfer and the mass transfer parameters respond significantly to the time dependent stretching velocities. Suction (A > 0) is found to be an important parameter in obtaining convergent solution in the case of the saddle point region of flow. The Prandtl number and the Schmidt number strongly affect the heat and mass transfer of the diffusing species, respectively.

Influence of anvil supports and overhangs in dynamic analysis of three point bend testing

Optimum design of dynamic fracture test rigs demands a thorough appreciation of beam vibration under impact. Analyses invariably presume rigid anvils, and neglect overhang effects. The beam response predicted analytically and numerically in this paper highlights the significant role of anvil rigidity and beam overhangs on the impact dynamics of three point bend (3PB) specimens.

Orientational ordering in C70. Evidence for three distinct phase transitions

Variable-temperature X-ray diffraction studies of C70 suggest the occurrence of two phase transitions around 350 and 280 K where the high-temperature phase is fcc and the low-temperature phase is monoclinic, best described as a distorted hcp structure with a doubled unit cell; two like-phases (possibly hcp) seem to coexist in the 280-350 K range. Application of pressure gives rise to three distinct transitions associated with characteristic pressure coefficients, the extrapolated values of the transition temperatures at ambient pressure being around 340, 325 and 270 K. Pressure delineates closely related phases Of C70 just as in the case Of C60 which exhibits two orientational phase transitions at high pressures.

Soft chemical synthesis of new layered and three-dimensional oxide hydrates, hxVxW1-xO3×yH2O, related to WO3×2 H2O and WO3. times.1/3 H2O

Two new vanadium-tungsten oxide hydrates of the formulas, H0.125V0.125W0.875O3.1.5H2O (I) and Ho.33V0.33W0.67O3.1/3H2O (II), have been synthesized by acid-leaching of LiVWO6 with aqueous HNO3/HCl. While phase I obtained by treatment of LiVWO6 with dilute HNO3/HCl possesses an orthorhombic structure (a = 7.77(3), b = 13.87(6), c = 7.44(3) angstrom) related to WO3.2H2O, phase II, prepared by refluxing LiVWO6 with concentrated HNO3, is isostructural with WO3.1/3H2O. Dehydration of II around 330-degrees-C yields a hexagonal phase (III, a = 7.25(4), c = 7.74(3) angstrom) isotypic with hexagonal WO3. Both land III exhibit redox and acid-base intercalation reactivity characteristic of layered and tunnel structures.

Solid finite elements through three decades

conventionally, solid finite elements have been looked upon as just generalizations of two-dimensional finite elements. In this article we trace their development starting from the days of their inception. Keeping in tune with our perceptions on developing finite elements, without taking recourse to any extra variational techniques, we discuss a few of the techniques which have been applied to solid finite elements. Finally we critically examine our own work on formulating solid finite elements based on the solutions to the Navier equations.

High-Throughput Study of the Cu(CH3COO)(2)center dot H2O-5-Nitroisophthalic Acid Heterocyclic Ligand System: Synthesis, Structure, Magnetic, and Heterogeneous Catalytic Studies of Three Copper Nitroisophthalates

A high-throughput screening was employed to identify new compounds in Cu(CH3COO)(2)center dot H2O-NIPA-heterocyclic ligand systems. Of the compounds identified, three compounds, Cu-3{(NO2)-C6H3-(COO)(2)}(3)(C3N6H6)] (1), Cu-2(mu(3)-OH)(H2O){(NO2)-C6H3-(COO)(2)}(CN4H)]center dot-(H2O) (II), and Cu-2(mu(3)-OH)(H2O){(NO2)-C6H3-(COO)(2}-)(CN5H2)]center dot 2(H2O) (III), have been isolated as good quality single crystals by employing conventional hydrothermal methods. Three other compounds, Cu-2{(NO2)-C6H3-(COO)(2)}-(CN4H)(H2O) (IIa), Cu-2{(NO2)-C6H3-(COO)(2)}(CN5H2) (IIIa), and Cu-2{(NO2)-C6H3-(COO)(2)}{(CN5H2)(2)}2H(2)O (IIIb), were identified by a combination of elemental analysis, thermogravimetric analysis (TGA), and IR spectroscopic studies, although their structures are yet to be determined. The single crystalline compounds were also characterized by elemental analysis, TGA, IR, UV vis, magnetic, and catalytic studies. The structures of the compounds have paddle wheel (I) and infinite Cu 0(H) Cu chains (II and HI) connected with NLPA and heterocyclic ligands forming two-(II) and three-dimensional (I and III) structures. The bound and lattice water molecules in 11 and 111 could be reversibly removed/inserted without affecting the structure. In the case of II, the removal of water gives rise to a structural transition, but the dehydrated phase reverts back to the original phase on prolonged exposure to atmospheric conditions. Magnetic studies indicate an overall antiferromagnetism in all of the compounds. Lewis acid catalytic studies indicate that compounds II and HI are active for cyanosilylation of imines.