Estudo da digestão de sedimento de curtume visando a extração do cromo por microemulsão

Leather tanneries generate effluents with high content of heavy metals, especially chromium, which is used in the mineral tanning process. Microemulsions have been studied in the extraction of heavy metals from aqueous solutions. Considering the problems related with the sediment resulting from the tanning process, due to its high content in chromium, in this work this sediment was characterized and microemulsion systems were applied for chromium removal. The extraction process consists in the removal of heavy metal ions present in an aqueous feeding solution (acid digestion solution) by a microemulsion system. First three different solid sludge digestion methods were evaluated, being chosen the method with higher digestion capacity. For this digestion method, seeking its optimization, was evaluated the influence of granule size, temperature and digestion time. Experimental results showed that the method proposed by USEPA (Method A) was the most efficient one, being obtained 95.77% of sample digestion. Regarding to the evaluated parameters, the best results were achieved at 95°C, 14 Mesh granule size, and 60 minutes digestion time. For chromium removal, three microemulsion extraction methods were evaluated: Method 1, in a Winsor II region, using as aqueous phase the acid digestion solution; Method 2, in a Winsor IV region, being obtained by the addition of the acid digestion solution to a microemulsion phase, whose aqueous phase is distilled water, until the formation of Winsor II system; and Method 3, in a Winsor III region, consisting in the formation of a Winsor III region using as aqueous phase the acid digestion solution, diluted in NaOH 0.01N. Seeking to optimize the extraction process only Method 1 (Systems I, II, and VIII) and Method 2 (System IX) were evaluated, being chosen points inside the interest regions (studied domains) to study the influence of contact time and pH in the extraction percentiles. The studied systems present the following compositions: System I: Surfactant Saponified coconut oil, Cosurfactant 1-Butanol, Oil phase Kerosene, Aqueous phase 2% NaCl solution; System II: Aqueous phase Acid digestion solution with pH adjusted using KOH (pH 3.5); System VIII: Aqueous phase - Acid digestion solution (pH 0.06); and System IX Aqueous phase Distilled water (pH 10.24), the other phases of Systems II, VIII and IX are similar to System I. Method 2 showed to be the more efficient one regarding chromium extraction percentile (up to 96.59% - pH 3.5). Considering that with Method 2 the microemulsion region only appears in the Winsor II region, it was studied Method 3 (System X) for the evaluation and characterization of a triphasic system, seeking to compare with a biphases system. System X is composed by: Surfactant Saponified coconut oil, Cosurfactant 1-Butanol, Oil phase Kerosene, Aqueous phase Acid digestion solution diluted with water and with its pH adjusted using 0.01N NaOH solution. The biphasic and triphasic microemulsion systems were analyzed regarding its viscosity, extraction efficiency and drop effective diameter. The experimental results showed that for viscosity studies the obtained values were low for all studied systems, the diameter of the drop is smaller in the Winsor II region, with 15.5 nm, reaching 46.0 nm in Winsor III region, being this difference attributed to variations in system compositions and micelle geometry. In chromium extraction, these points showed similar results, being achieved 99.76% for Winsor II system and 99.62% for Winsor III system. Winsor III system showed to be more efficient due to the obtaining of a icroemulsion with smaller volume, with the possibility to recover the oil phase in excess, and the use of a smaller proportion of surfactant and cosurfactant (C/S)

Estudo etnofarmacológico e fitoquímico das espécies medicinais Cleome spinosa Jacq, Pavonia varians Moric e Croton cajucara Benth

In this present work an ethnographic research was performed with 84 native medicinal specimens from the Litoral Norte Riograndense, from which two plants Cleome spinosa Jacq e Pavonia varians Moric were submitted to ethnobotanic, phytochemistry and pharmacologic investigations. Additionally, a phytopharmacological research of the medicinal specimen Croton cajucara Benth ( native plant of the Amazon region of Brazil) was improved. The obtained phytochemical results of the C. spinosa and P. varians showed the presence of flavonoids constituents, among other components. The two flavonoids (2S)-5-hydroxy-7,4 -dimethoxy-flavanone and 5,4 -dihydroxy-3,7,3 -trimethoxy-flavone were isolated from C. spinosa. The antioxidant activity of the hydroalcoholic extracts of C. spinosa and P. varians solubilized in the microemulsion systems SME-1 and SME-4, was evaluated in the DPPHmethod. The used SME systems [obtained with Tween 80: Span 20 (3:1) and isopropyl myristate (IPM)] improved the dissolution of those tested polar extracts, with higher efficacy to the SME-1 system (in which ethanol was included as cosurfactant). The CE50 values evidenced for P. varians were 114 [g/mL (SME-1) and 246 [g/mL (SME-4); for C. spinosa it was 224 [g/mL (SME-1) and 248 [g/mL (SME-4), being the system SME-1 more effective for both tested extracts. The hydroalcoholic extracts of P. varians (HAE-PV) was also submitted to pharmacological screening for antinociceptive activity in animal models. The oral administration of this extract (100, 300 and 1000 mg/kg) inhibited the acetic acid-induced writhing in mice. The higher inhibition (74%) was evidenced to the 1000 mg/kg administered dose. Its effect on the central nervous system (CNS) was investigated by tail flick and formalin-method and reveled that it has negligible antinociceptive action on the CNS. After taking consideration of HAE-PV interaction, Pavonia varians Moric could be used as a potent analgesic agent in case of peripheral algesia, without affecting the CNS. The phytochemical study of the stem bark of Croton cajucara Benth lead to the isolation of 19-nor-clerodanetype diterpenes, as well as to the separation of its fixed oil FO-CC. This non polar oil material reveled to be rich in sesquiterpenes and 19-nor-clerodanes components. The biologic effect of OF-CC was evaluated in the development in vitro of the fungis phytopatogens such as Fusarium oxysporum, Rhizoctonia solani and Sclerotium rolfsii. Significant inhibitory effect of the tested fungis (at 0,2 mg.mL-1 dosage) were comproved. A Mass Spectrometry study of clerodane-type diterpenes was developed in order to identify characteristic fragments on mass spectrometra of both clerodane and 19-nor-clerodane presenting an α,β-insaturated carbonyl moiety at ring A of the decalin-system. For that study, mass spectroscopy data were analysed for 19-nor-clerodanes [trans-dehydrocrotonin (DCTN), trans-crotonin (CTN), cis-cajucarin B (c-CJC-B), and cajucarinolide (CJCR)] and for clerodanes [isosacacarin (ISCR) and transcajucarin A (t-CJC-A)] obtained from the stem bark of C. cajucara, and also clerodane-type from other species. The trans-junction of the enone-system clerodanes was clear correlated with the presence of the characteristic ions at m/z 95, 121 e 205. Meanwhile, the characteristics ions at m/z 122 e 124 were correlated to cis-junction. The trans-junction of the enone-system 19-nor-clerodanes showed characteristics ions at m/z 161, 134 e 121. This study could be successful employed for identification of clerodane constituents from other specimens without any additional spectroscopic analyses, as well as a previously phytochemical analyzes in clerodane project search

Assinaturas antropogênicas de elementos maiores e traços em poeira urbana na cidade do Natal-RN

Although there are many studies on urban dust contamination by heavy metals in developed countries, little attention has been paid to this type of study in developing countries, including Brazil. Therefore, a series of investigations were performed to provide signatures of heavy metals in urban dust and assess the potential sources in the city of Natal - RN-Brazil. The fraction of these sediments was studied to pass through a sieve of 63 micrometers. For the study analyzed two groups of samples, one collected in September 2009 at the end of the rainy season (9 samples) and one collected in January 2010 in the dry season (21 samples). So in all, thirty sediment samples were collected from the street. Then, in Fluorescence Spectrometry X-rays were determined major elements SiO2, Na2O, K2O, Al2O3, MgO, P2O5, Fe2O3, MnO, TiO2 and CaO, and trace Rb, Cr, Ni, Cu, Zn, Sr and Pb by an ICPOES was determined Zn, V, Na, K, Ni, Mn, Mg, P, Fe, Cr, Cu, Pb, Ba, Ca and Al from leaching HCl 0.5 mol L-1 . The results of the concentrations of elements show that the greater presence of these occurs in the dry season, except for Si which is higher in the rainy season. Analyses by geoaccumulation Index (IGEO) Enrichment Factor (EF), Contamination Factor (CF), analysis correlation and Hierarchical Cluster, confirm that Zn, Cu and Pb is anthropogenic character. Zinc may be derived from various sources related to motor vehicles or the road signs and street grids. The elements Na, K, Mg and Ca may be related to droplets suspended in air containing cations and anions present in seawater (salty), common in Christmas throughout the year, brought by winds SE-NW. The elements Na, Mg, Ca and K are the most abundant in seawater and were analyzed in this study. This indicates that the source of these additional elements detected by analyzing the contamination factor may be the very sea. Moreover, Ni, Fe, Cr and Ba can be either as a source of anthropogenic geogênica. The source of Ca is different, because it comes in lime and paint (painting guides of buildings and streets) in construction materials, but may also be present in sediments in the fragments of shells or carbonate bioclasts common in the coastal area

Matrizes poliméricas puras e modificadas para adsorção do gás sulfeto de hidrogênio

The underground natural gas found associated or not with oil is characterized by a mixture of hydrocarbons and residual components such as carbon dioxide (CO2), nitrogen gas (N2) and hydrogen sulfide (H2S), called contaminants. The H2S especially promotes itself as a contaminant of natural gas to be associated with corrosion of pipelines, to human toxicity and final applications of Natural Gas (NG). The sulfur present in the GN must be fully or partially removed in order to meet the market specifications, security, transport or further processing. There are distinct and varied methods of desulfurization of natural gas processing units used in Natural Gas (UPGN). In order to solve these problems have for example the caustic washing, absorption, the use of membranes and adsorption processes is costly and great expenditure of energy. Arises on such findings, the need for research to active processes of economic feasibility and efficiency. This work promoted the study of the adsorption of sulfide gas in polymer matrices hydrogen pure and modified. The substrates of Poly(vinyl chloride) (PVC), poly(methyl methacrylate) (PMMA) and sodium alginate (NaALG) were coated with vanadyl phosphate compounds (VOPO4.2H2O), vanadium pentoxide (V2O5), rhodamine B (C28H31N2O3Cl) and ions Co2+ and Cu2+, aiming to the adsorption of hydrogen sulfide gas (H2S). The adsorption tests were through a continuous flow of H2S in a column system (fixed bed reactor) adsorption on a laboratory scale. The techniques used to characterize the adsorbents were Infrared spectroscopy (FTIR), thermogravimetry analysis (TGA), X-ray fluorescence (XRF), the X-ray diffraction (XRD) electron microscopy (SEM). Such work indicates, the results obtained, the adsorbents modified PMMA, PVC and NaALG have a significant adsorptive capacity. The matrix that stood out and had the best adsorption capacity, was to ALG modified Co2+ with a score of 12.79 mg H2S / g matrix

Estudo das características magnéticas e absorvedoras das ferritas de nizn, niznmn, mnzn, nimg, nicuzn e nicuznmg obtidas via método do citrato precursor

Were synthesized systems Ni0,5Zn0,5Fe2O4, i0,2Zn0,5Mn0,3Fe2O4, Mn0,5Zn0,5Fe2O4, Ni0,5Mg0,5Fe2O4, Ni0,2Cu0,3Zn0,5Fe2O4 and Ni0,2Cu0,3Zn0,5Mg0,08Fe2O4, the precursors citrate method. The decomposition of the precursors was studied by thermogravimetric analysis and spectroscopy in the infrared region, the temperature of 350°C/3h. The evolution of the phases formed after calcinations at 350, 500, 900 and 1100ºC/3h was accompanied by X-ray diffraction using the Rietveld refinement to better identify the structures formed. The materials were also analyzed by scanning electron microscopy, magnetic measurements and analysis of the reflectivity of the material. The samples calcined at different temperatures showed an increase of crystallinity with increasing calcination temperature, verifying that for some compositions at temperatures above 500°C precipitates of second phase such as hematite and CuO. The compositions of manganese present in the structure diffusion processes slower due to the ionic radius of manganese is greater than for other ions substitutes, a fact that delays the stabilization of spinel structure and promotes the precipitation of second phase. The compositions presented with copper precipitation CuO phase at a temperature of 900 and 1100ºC/3h This occurs according to the literature because the concentration of copper in the structure is greater than 0.25 mol%. The magnetic measurements revealed features of a soft ferrimagnetic material, resulting in better magnetic properties for the NiZn ferrite and NiCuZnMg at high temperatures. The reflectivity measurements showed greater absorption of electromagnetic radiation in the microwave band for the samples calcined at 1100ºC/3h, which has higher crystallite size and consequently the formation of multi-domain, increasing the magnetization of the material. The results of absorption agreed with the magnetic measurements, indicating among the ferrites studied, those of NiZn and NiCuZnMg as better absorbing the incident radiation.

Caracterização dos eletrocatalisadores LaMnO3, LaFeO3, LaFe0,2Mn0,8O3 E La0,5Fe0,5MnO3 preparados por autocombustão assistida por microondas para cátodos de células a combustível do tipo SOFC

Materials consisting of perovskite-type oxides (ABO3) have been developed in this work for applications in fuel cell cathodes of solid oxide type (SOFC). These ceramic materials are widely studied for this type of application because they have excellent electrical properties, conductivity and electrocatalytic. The oxides LaMnO3, LaFeO3, LaFe0.2Mn0.8O3 e La0.5Fe0.5MnO3 were synthesized by the method of microwave assisted combustion and after sintering at 800°C in order to obtain the desired phases. The powders were characterized by thermogravimetry (TG), X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM) and voltammetric analysis (cyclic voltammetry and polarization curves). The results obtained by XRF technique showed that the microwave synthesis method was effective in obtaining doping oxides with values near stoichiometric. In general, powders were obtained with particle size less than 0.5 μm, having a porous structure and uniform particle size distribution. The particles showed spherical form, irregular and crowded of varying sizes, according to the analysis of SEM. The behavior of the oxides opposite the thermal stability was monitored by thermogravimetric curves (TG), which showed low weight loss values for all samples, especially those of manganese had its structure. By means of Xray diffraction of the samples sintered at 800°C was possible to observe the formation of powders having high levels of crystallinity. Furthermore, undesirable phases such as La2O3 and MnOx were not identified in the diffractograms. These phases block the transport of oxygen ions in the electrode/electrolyte interface, affecting the electrochemical activity of the system. The voltammetric analysis of the electrocatalysts LF-800, LM-800, LF2M8-800 e L5F5M-800 revealed that these materials are excellent electrical conductors, because it increased the passage of electrical current of the working electrode significantly. Best performance for the oxygen reduction reaction was observed with iron-rich structures, considering that the materials obtained have characteristics suitable for use in fuel cell cathodes of solid oxide type

Obtenção e caracterização do sistema compósito alginato de sódio-dióxido de titânio em formas de pó e de membrana

The alginates are copolymers of 1→4-linked β-D-mannuronic acid (M) and α-Lguluronic acid (G) residues that are arranjed in a block structure along a linear chain. Titanium dioxide, TiO2, is a ceramic material and can exist in three distinct crystallography forms: anatase, brookite and rutile. composites of organic and inorganic materials have better properties than the components alone. Thus, this study aims to synthesize, characterize and analyze the composite NaAlg-TiO2 in the form of powder and film. The synthesis of composite powders was performed using the sol-gel process and obtain the composite film was performed using the slow evaporation process, then the composites were analyzed by infrared spectroscopy, fluorescence x ray, thermal analysis, attenuated total reflection (ATR), x ray diffraction and impedance spectroscopy. The X ray diffraction patterns of composite powders show that with increasing calcination temperature, there were no complete transition of rutile-anatase crystalline phase, since at all temperatures studied (300, 500, 700, 900 and 1100ºC) were observed peaks of anatase phase. Thermal analysis shows that at 400°C caused the decomposition of sodium alginate in sodium carbonate and above 600°C, we observe an exothermic peak related to the decomposition of sodium carbonate and in the presence of titanium dioxide becomes sodium titanate. The XRD results confirm the formation of sodium carbonate at 700ºC and the formation sodium titanate in the temperature range 900-1100ºC. The sodium titanate influenced the electrical properties of the material, because with increasing temperature there was a decrease in conductivity, probably due to the creation of Ti vacancies, since the sodium can induce the reduction of surface Ti4+ ions into Ti3+ species. The infrared spectra of the composites in the form of powder and film showed a small shift in the bands compared to the spectrum of pure alginate, indicating that these shifts, even small ones, have evidence of miscibility between the polymer and ceramic material

Avaliação da poatencialidade da perlita natural e expandida na adsorção de metais

The contamination by metal ions has been occurring for decades through the introduction of liquid effluent not treated, mainly from industrial activities, rivers and lakes, affecting water quality. For that the effluent can be disposed in water bodies, environmental standards require that they be adequately addressed, so that the concentration of metals does not exceed the limits of standard conditions of release in the receptor. Several methods for wastewater treatment have been reported in the literature, but many of them are high cost and low efficiency. The adsorption process has been used as effective for removal of metal ions. This paper presents studies to evaluate the potential of perlite as an adsorbent for removing metals in model solution. Perlite, in its natural form (NP) and expanded (EP), was characterized by X-ray fluorescence, X-ray diffraction, surface area analysis using nitrogen adsorption (BET method), scanning electron microscopy and Fourier transform infrared spectroscopy. The physical characteristic and chemical composition of the material presented were appropriate for the study of adsorption. Adsorption experiments by the method of finite bath for model solutions of metal ions Cr3+, Cu2+, Mn2+ and Ni2+ were carried out in order to study the effect of pH, mass of the adsorbent and the contact time on removal of ions in solution. The results showed that perlite has good adsorption capacity. The NP has higher adsorption capacity (mg g-1) than the EP. According to the values of the constant of Langmuir qm (mg g-1), the maximum capacity of the monolayer was obtained and in terms of proportion of mass, we found the following order experimental adsorption: Cr3+ (2.194 mg g- 1) > Ni2+ (0.585 mg g-1) > Mn2+ (0.515 mg g-1) > Cu2+ (0.513 mg g-1) and Cr3+ (1.934 mg g-1)> Ni2+ (0.514 mg g-1) > Cu2+ (0.421 mg g-1) > Mn2+ (0.364 mg g-1) on the NP and EP, respectively. The experimental data were best fitted the Langmuir model compared to Freundlich for Cu2+, Mn2+ and Ni2+. However, for the Cr3+, both models fit the experimental data

Síntese pelo método pechini e caracterização da zircônia dopada com cério e neodímio

In this study five compositions were synthesized zirconia doped with cerium and neodymium ions in the system Ce10-xNdx Zr90O2 with 0,5 ≤ x ≤ 4,0 using the Pechini method. The powders were characterized by thermogravimetric analysis, differential thermal analysis, infrared spectroscopy and X-ray diffraction, with application of Rietveld refinement of the calcination temperatures of 350ºC/3h and 30 minutes at 900ºC/3h. All compositions stabilized with a mixture of cubic and tetragonal phase zirconia. The samples were pressed into bars and sintered at 1500°C/3h and 1500°C/6h, being characterized by Xray diffraction, with application of the Rietveld refinement, density and porosity using Archimedes method, scanning electron microscopy and resistance the three point bending. It has been observed the increase in strength with increasing sintering temperature for the compositions x = 2,0 and x = 4,0. For x = 2,0 the main phase was the cubic with 92,56% with crystallite size of 0,56 μm, density and porosity of 96,82% from 1,36%. For x = 4,0 was a mixture of cubic and tetragonal phase with 21% and 37,98%, respectively. The crystallite size was 54,21 nm and 49,64 nm with a density porosity of 97,45% and 1,32% respectively. In the analysis of the fracture surface was observed a greater amount of grain fracture intragranular type, which contribute to increase the mechanical strength of the ceramic. Increased addition of the neodymium ion in the crystal lattice of the zirconium showed a nearly linear behavior with increasing mechanical strength of the zirconia ceramic. Was obtained a bending resistance of 537 ± 38 MPa for the composition x = 2,0 predominantly attributed to cubic phase with 92,56%

Síntese e caracterização de compostos de coordenação homolépticos e heterolépticos com o ligante ácido kójico

The present work has as main objective to contribute to the coordination chemistry of the ligand kojic acid, with the synthesis and characterization of the homoleptic compounds [Al(kj)3], [Fe(kj)3], [Fe(kj)2], [Cu(kj)2] e [Ru(kj)3], and the new heteroleptic complexes, trans- K2[Fe(kj)2(CN)2] and trans-Na2[Ru(kj)2(CN)2]. The obtained compounds were characterized by vibrational spectroscopy in the infrared region (IV) and Electronic spectroscopy in the ultraviolet and visible region (Uv-Vis). The infrared results indicated the coordination of the bidentate ligand kojic acid, due to reductions in the values of the stretching frequencies of the carbonyl and double bonds, compared to the free ligand for all complexes obtained. The presence of new vibrational modes indicated the change of symmetry of the molecules in the new compounds synthesized. Additionally, the presence of vibrational modes assigned to metal-oxygen also contributed to confirm the ligand coordinating to the metal ions. Through this technique, was also possible to perform correlations of the numbers of vibrational modes, in the region 1400-900 cm-1 and the compounds geometry. The heteroleptic compounds exhibited υC≡N in 2065 and 2053 cm-1, respectively, for the trans-K2[Fe(kj)2(CN)2] and trans-Na2[Ru(kj)2(CN)2], indicating coordination of the cyano ligand to metal ions FeII e RuII. Comparing the obtained values with literature data was possible to identify the complex isomerism as trans. In relation to the results of electronic spectroscopy, studies of pH variation of kojic acid provided information on the distribution of electron density in the molecule, showing characteristic spectral profile of kojic ion and its protonated form (Hkj, kojic acid), with two bands at 215 and 269 nm, or deprotonated (kj-), with bands at 226 and 315 nm. The electronic spectra obtained for all complexes in aqueous medium, in the ultraviolet region, exhibited variations of the energies assigned to kojic acid intraligand transitions while in the visible region, only transitions assigned to charge transfer of iron and ruthenium complex have been identified

Síntese e caracterização de redes metalorgânicas baseadas em zinco e ácidos benzenodicarboxílicos

Metal Organic Frameworks (MOFs) are supramolecular structures consisted of ions or metal clusters coordinated to organic ligands which are repeated in two or three dimensions. These structures have atracted much attention due to their properties such as low density, high specific surface area and large volume of pores. In this work, MOFs consisted of zinc clusters connected by ditopic ligands, terephthalic acid (1,4- H2BDC) or isophthalic acid (1,3-H2BDC) were synthesized. To obtain the proposed materials, different routes and synthetic parameters were tested, such as the molar ratio of the precursors, the addition of template molecules, the type of solvente, the addition of organic base or the type of a counter-ion of Zn salt. It was found that the variation of these parameters led to the formation of different metalorganic structures. The solids obtained were characterized by XRD, SEM and IR. For the samples identified as MOF- 5, it was verified that the structure was composed of both interpenetrated and non interpenetrated structures. These samples showed a low stability, becoming totally transformed into another structure within less than 72 hours. The addition of the nickel and/or cobalt was found to be a promissing method for increasing the stability of MOF- 5, which in this case, still remained unconverted to another structure even after 15 days of exposure to air. The samples prepared from 1,3-H2BDC were probably new, still unknown Metal Organic Frameworks

Estudo cinético da degradação térmica e catalítica de petróleo pesado usando Al-MCM-41

The mesoporous nanostructured materials have been studied for application in the oil industry, in particular Al-MCM-41, due to the surface area around 800 to 1.000 m2 g-1 and, pore diameters ranging from 2 to 10 nm, suitable for catalysis to large molecules such as heavy oil. The MCM-41 has been synthesized by hydrothermal method, on which aluminum was added, in the ratio Si/Al equal to 50, to increase the generation of active acid sites in the nanotubes. The catalyst was characterized by X-ray diffraction (XRD), surface area by the BET method and, the average pore volume BJH method using the N2 adsorption, absorption spectroscopy in the infrared Fourier Transform (FT-IR) and determination of surface acidity with application of a probe molecule - n-butylamine. The catalyst showed well-defined structural properties and consistent with the literature. The overall objective was to test the Al-MCM-41 as catalyst and thermogravimetric perform tests, using two samples of heavy oil with API º equal to 14.0 and 18.5. Assays were performed using a temperature range of 30-900 ° C and heating ratios (β) ranging from 5, 10 and 20 °C min-1.The aim was to verify the thermogravimetric profiles of these oils when subjected to the action of the catalyst Al- MCM-41. Therefore, the percentage ranged catalyst applied 1, 3, 5, 10 and 20 wt%, and from the TG data were applied two different kinetic models: Ozawa-Flynn-Wall (OFW) and Kissinger-Akahrira-Sunose (KAS).The apparent activation energies found for both models had similar values and were lower for the second event of mass loss known as cracking zone, indicating a more effective performance of Al-MCM-41 in that area. Furthermore, there was a more pronounced reduction in the value of activation energy for between 10 and 20% by weight of the oil-catalyst mixture. It was concluded that the Al-MCM-41 catalyst has applicability in heavy oils to reduce the apparent activation energy of a catalyst-oil system, and the best result with 20% by weight of Al-MCM-41

Estudo integrado do potencial fitorremediador da Eichhornia crassipes em ambientes naturais e sua utilização para obtenção de extratos proteicos

This study aimed to analyze the phytoremediation potential of Eichhornia crassipes in natural environments, optimize the extraction process of crude protein from plant tissue and, obtain and characterize this process in order to determine its viability of use instead of the protein sources of animal and/or human feed. For this, it has been determined in Apodi/Mossoró river water the concentration of ammonium ions, nitrite, nitrate, calcium, magnesium, potassium, iron, copper, manganese, zinc, nickel, cobalt, sodium, aluminum, cádmium, lead, and total chromium; It was determined in plant tissue of aquatic macrophytes of Eichhornia crassipes species present in Apodi/Mossoró River the moisture content, ash, calcium, magnesium, potassium, iron, copper, manganese, zinc, nickel, cobalt, sodium, aluminum, cadmium, lead, total chromium, total nitrogen and crude protein. It was also determined the translocation factor and bioaccumulation of all the quantified elements; It was developed and optimized the extraction procedure of crude protein based on the isoelectric method and a factorial design 24 with repetition; It was extracted and characterized the extract obtained by determining the moisture content, ash, magnesium, potassium, iron, copper, manganese, zinc, nickel, cobalt, sodium, cadmium, total nitrogen and crude protein. And finally, it was also characterized the protein extract using Thermogravimetric Analysis (TG), Derived Thermogravimetric (DTG), Differential Scanning Calorimetry (DSC), Infrared Spectroscopy (FT-IR) and jelly-like electrophoresis of polyacrylamide (SDS -PAGE) to assess the their molecular weights/mass. Thus, from the results obtained for the translocation and bioaccumulation factors was found that the same can be used as phytoremediation agent in natural environments of all quantified elements. It was also found that the developed method of extraction and protein precipitation was satisfactory for the purpose of the work, which gave the best conditions of extraction and precipitation of proteins as: pH extraction equal to 13.0, extraction temperature equals 60 ° C, reaction time equals to 30 minutes, and pH precipitation equals to 4.0. As for the extract obtained, the total nitrogen and crude protein were quantified higher than those found in the plant, increasing the crude protein content approximately 116.88% in relation to the quantified contente in the vegetal tissue of macrophyte. The levels of nickel and cadmium were the unique that were found below the detection limit of used the equipment. The electrophoretic analysis allowed us to observe that the protein extract obtained is composed of low polypeptide chains by the molecular and phytochelatins, with 6 and 15 kDa bands. Analysis of TG, DTG, DSC and FT-IR showed similarities in protein content of the obtained extracts based on different collection points and 9 parts of the plant under study, as well as commercial soy protein and casein. Finally, based on all these findings, it was concluded that the obtained extract in this work can be used instead of the protein sources of animal feed should, before that, test its digestibility. As human supplementation, it is necessary to conduct more tests associated with the optimization process in the sense of removing undesirable components and constant monitoring of the water body and the raw material used

Efeito de lodo de esgoto na fertilidade de um Argissolo Vermelho-Amarelo cultivado com cana-de-açúcar

O objetivo deste trabalho foi avaliar os efeitos da aplicação de 0, 20 e 40 Mg ha-1 de lodo de esgoto, na presença e ausência de fertilizante mineral (NPK) na fertilidade e nos teores de metais pesados de um Argissolo Vermelho-Amarelo distrófico, cultivado com cana-de-açúcar. Amostras de solo foram coletadas aos 146, 272 e 484 dias após o plantio da cultura de cana-de-açúcar e foram submetidas à análise de fertilidade pelo método do Instituto Agronômico de Campinas, incluindo a determinação do S, Cr, Cd, Cu, Fe, Mn, Pb e Zn. O lodo de esgoto diminuiu a acidez do solo e forneceu Ca, P, S e Zn, principalmente. Seus efeitos foram de curta duração, restringindo-se a um ano agrícola. Os teores dos metais pesados das amostras de solo tratado foram maiores que os da testemunha, mas menores que os valores considerados perigosos ao ambiente.

Características de carcaça e composição corporal de touros jovens da raça Nelore terminados em diferentes sistemas

O objetivo do trabalho foi avaliar comparativamente as características de carcaça e a composição corporal de machos jovens da raça Nelore não-castrados, filhos de touros com diferencial positivo (Linhagem Seleção) ou nulo (Linhagem Controle) para ganho de peso aos 378 dias de idade. Utilizaram-se informações de 92 zebuínos Nelore, com peso de abate médio de 456,00 kg, sendo 51 animais pertencentes à Linhagem Seleção e 41 animais da Linhagem Controle, foram criados em pastagens cultivadas até os 18 meses, quando foram alocados nos dois sistemas de terminação, de forma a compor grupos homogêneos quanto ao peso e filiação. Os animais de confinamento receberam, em baias individuais, ração para possibilitar ganhos de 1,0 kg/cab/dia. Antes do abate, os animais foram submetidos a jejum e pesados, quando se obteve o peso de abate. Após o armazenamento das carcaças em câmara fria, obteve-se a seção da 9ª-10ª-11ª costelas. Não houve efeito significativo de linhagem para nenhuma das características analisadas, exceto para a porcentagem de ossos, sendo que os animais da Linhagem Seleção superaram os animais da Linhagem Controle. O regime de terminação apresentou efeito significativo para a quase totalidade das características estudadas, com exceção para as características de composição corporal. Não houve efeito significativo de interação entre linhagem e terminação. As classes de idade apresentaram efeito significativo para as características peso de abate, peso de carcaça quente, peso da gordura renal-pélvica-ingüinal, porcentagem de músculo, gordura e osso.