Gender-based differences in stride and limb dimensions between healthy red-wing tinamou (Rhynchotus rufescens) Temminck, 1815

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento de Uma Órtese Ativa Para os Membros Inferiores Com Sistema Eletrônico Embarcado

This work presents the development of a prototype of an intelligent active orthosis for lower limbs whit an electronic embedded system. The proposed orthosis is an orthopedical device with the main objective of providing walking capacity to people with partial or total loss of lower limbs movements. In order to design the kinematics, dynamics and the mechanical characteristics of the prototype, the biomechanics of the human body was analized. The orthosis was projected to reproduce some of the movements of the human gait as walking in straight forward, sit down, get up, arise and go down steps. The joints of the orthosis are controlled by DC motors equipped with mechanical reductions, whose purpose is to reduce rotational speed and increase the torque, thus generating smooth movements. The electronic embedded system is composed of two motor controller boards with two channels that communicate with a embedded PC, position sensors and limit switches. The gait movements of the orthosis will be controlled by high level commands from a human-machine interface. The embedded electronic system interprets the high level commands, generates the angular references for the joints of the orthosis, controls and drives the actuators in order to execute the desired movements of the user

EFFICIENCY of PNEUMATIC and HORIZONTAL PERFORATED DISK METER MECHANISM IN CORN NO-TILLAGE SEEDERS IN SOIL WITH DIFFERENT MOBILIZATION REPORTS

This work objectified to evaluate the efficiency of two meter mechanism of corn seeds when submitted to different forward speed and soil management system during the non-tillage seeding. It was used a factorial design in randomized blocks. The factors whose effects were examined were related to the seeders with pneumatic and horizontal disk meter mechanisms for the distribution of the seeds, to the set tractor-seeder forward speeds (4.4; 8.0 and 9.8 km h(-1)), and to the soil management system considering the corn no-tillage seeding over minimum tillage with chisel plow and the no-tillage system for the seeding of oat culture (Avena strigosa Schreb). It was verified that the forward speed didn't influence the initial and final stands of plants but it interfered in the regularity of longitudinal distribution of plants. The smallest speed provided the largest percentile of normal spacing between plants. The pneumatic meter mechanism presented better performance than the horizontal disk perforated in the longitudinal distribution of plants. About corn productivity aspect it's indifferent the recommendation of use for pneumatic and perforated horizontal disk meter mechanism of seeds.

Aplicações de Dispositivos de Microondas utilizando Substrato EBG/PBG para Comunicações Móveis

The modern society depends on an efficient communications system able to of transmitting and receiving information with a higher speed and reliability every time. The need for ever more efficient devices raises optimization techniques of microstrip devices, such as techniques to increase bandwidth: thicker substrates and substrate structures with EBG (Electromagnetic Band Gap) and PBG (Photonic Band Gap). This work has how aims the study of the application of PBG materials on substrates of planar structures in microstrip, more precisely in directional quadrature couplers and in rat-race and impedance of transformers. A study of the planar structures in microstrip and substrates EBG is presented. The PBG substrates can be used to optimize the radiation through the air, thus reducing the occurrence of surface waves and the resulting diffraction edge responsible for degradation of radiation pattern. Through specific programs in FORTRAN Power Station obtained the frequencies and couplings for each structure. Are used the program PACMO - Computer Aided Design in Microwave. Results are obtained of the frequency and coupling devices, ranging the frequency band used (cellular communication and Wimax systems) and the permittivity of the substrate, comparing the results of conventional material and PBG materials in the s and p polarizations.

Phosphorus sources and fractions in an oxisol under no-tilled soybean

A dinâmica do P no solo pode ser modificada em sistemas com semeadura direta. Os agricultores brasileiros vêm aplicando fósforo na superfície do solo para otimizar a operação de máquinas, embora não seja uma prática recomendada pela pesquisa. Foi conduzido um experimento para estudar os efeitos da aplicação de duas fontes de fósforo na superfície do solo e no sulco de semeadura da soja. Os tratamentos consistiram da aplicação ou não de 80 kg ha-1 de P total como fosfato natural reativo e superfosfato, aplicados na superfície do solo, sobre os resíduos da cultura anterior. Na semeadura da soja, tratamentos adicionais (80 kg ha-1 de fosfato natural ou superfosfato) foram aplicados ao sulco de semeadura. O solo foi amostrado até 40 cm de profundidade, antes da semeadura da soja e após a colheita. Uma amostra controle foi tomada de área adjacente, sem cultivo. Houve aumento nos teores de P até 40 cm de profundidade, após a colheita da soja, de modo que o aumento foi observado principalmente no P ligado ao Ca e no P orgânico. Entretanto houve decréscimo nos teores de P ligado ao Fe. A adubação com ambas as fontes de fosfato levaram a um decréscimo nos teores de P ocluso na superfície do solo quando comparada com a área sem cultivo.

Composto orgânico na produção e qualidade de sementes de brócolis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Otimização do fresamento de roscas internas com a técnica de interpolação helicoidal

In machining of internal threads, dedicated tools, known as taps, are needed for each profile type, diameter, and low cutting speed values are used when compared to main machining processes. This restriction in the cutting speed is associated with the difficulty of synchronizing the tool s rotation speed and feed velocity in the process. This fact restricts the flexibility and makes machining lead times longer when manufacturing of components with threads is required. An alternative to the constraints imposed by the tap is the thread milling with helical interpolation technique. The technique is the fusion of two movements: rotation and helical interpolation. The tools may have different configurations: a single edge or multiple edges (axial, radial or both). However, thread milling with helical interpolation technique is relatively new and there are limited studies on the subject, a fact which promotes challenges to its wide application in the manufacturing shop floor. The objective of this research is determine the performance of different types of tools in the thread milling with helical interpolation technique using hardened steel workpieces. In this sense, four tool configurations were used for threading milling in AISI 4340 quenched and tempered steel (40 HRC). The results showed that climb cut promoted a greater number of machined threads, regardless of tool configuration. The upcut milling causes chippings in cutting edge, while the climb cutting promotes abrasive wear. Another important point is that increase in hole diameter by tool diameter ratio increases tool lifetime

Oxidação úmida de fenóis com catalisadores de ferro suportado em argilominerais em reator de leito de lama (slurry)

The wet oxidation of organic compounds with CO2 and H2O has been demonstrated to be an efficient technique for effluent treatment. This work focuses on the synthesis, characterization and catalytic performance of Fe-MnO2/CeO2, K-MnO2/CeO2/ palygorskite and Fe/ palygorskite toward the wet oxidative degradation of phenol. The experiments were conducted in a sludge bed reactor with controlled temperature, pressure and stirring speed and sampling of the liquid phase. Experiments were performed on the following operating conditions: temperature 130 ° C, pressure 20.4 atm, catalyst mass concentration of 5 g / L initial concentration of phenol and 0.5 g / L. The catalytic tests were performed in a slurry agitated reactor provided with temperature, pressure and agitation control and reactor liquid sampling. The influences of iron loaded on the support (0.3; 7 and 10%, m/m) and the initial pH of the reactant medium (3.1; 6.8; 8.7) were studied. The iron dispersion on the palygorskite, the phase purity and the elemental composition of the catalyst were evaluated by X-Ray Difraction (XRD), Scanning Electron Microscopy (SEM) and X-Ray Flourescence (XRF). The use of palygorskite as support to increase the surface area was confirmed by the B.E.T. surface results. The phenol degradation curves showed that the Fe3+ over palygorskite when compared with the other materials tested has the best performance toward the (Total Organic carbonic) TOC conversion. The decrease in alkalinity of the reaction medium also favors the conversion of TOC. The maximum conversion obtained from the TOC with the catalyst 3% Fe / palygorskite was around 95% for a reaction time of 60 minutes, while reducing the formation of acids, especially acetic acid. With products obtained from wet oxidation of phenol, hydroquinone, p-benzoquinone, catechol and oxalic acid, identified and quantified by High Performance Liquid Chromatography was possible to propose a reaction mechanism of the process where the phenol is transformed into the homogeneous and heterogeneous phase in the other by applying a kinetic model, Langmuir-Hinshelwood type, with evaluation of kinetic constants of different reactions involved.

Modifiable risk factors for overweight and obesity in children and adolescents from São Paulo, Brazil

Background: Brazil is currently experiencing a nutrition transition: the displacement of traditional diets with foods high in saturated fat, sodium, and cholesterol and an increase in sedentary lifestyles. Despite these trends, our understanding of child obesity in Brazil is limited. Thus, the aims of this study were (1) to investigate the current prevalence of overweight and obesity in a large sample of children and adolescents living in São Paulo, Brazil, and (2) to identify the lifestyle behaviors associated with an increased risk of obesity in young Brazilians.Methods: A total of 3,397 children and adolescents (1,596 male) aged 7-18 years were randomly selected from 22 schools in São Paulo, Brazil. Participants were classified as normal weight, overweight, or obese based on international age-and sex-specific body mass index thresholds. Selected sociodemographic, physical activity, and nutrition behaviors were assessed via questionnaire.Results: Overall, 19.4% of boys and 16.1% of girls were overweight while 8.9% and 4.3% were obese. Two-way analysis of variance revealed that the prevalence of overweight and obesity was significantly higher in boys and in younger children when compared to girls and older children, respectively (P < 0.05 for both). Logistic regression analysis revealed that overweight was associated with more computer usage, parental encouragement to be active, and light soft drink consumption after controlling for differences in sex, age, and parental education (P < 0.05 for all). Conversely, overweight was associated with less active transport to school, eating before sleep, and consumption of breakfast, full-sugar soft drinks, fried food and confectionery (P < 0.05 for all).Conclusions: Our results show that obesity in São Paulo children and adolescents has reached a level equivalent to that seen in many developed countries. We have also identified three key modifiable factors related to obesity that may be appropriate targets for future intervention in Brazilian youth: transport mode to school, computer usage, and breakfast consumption.

Soy beta-Conglycinin (7S Globulin) Reduces Plasma and Liver Cholesterol in Rats Fed Hypercholesterolemic Diet

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Chemical and Bioactive Quality Traits During Fruit Ripening in Eggplant (S-melon gena L.) and Allied Species

A chemical and bioactive quality evaluation of phytochemicals content of 10 eggplant lines and three allied species (S. sodomaeum, S. aethiopicum and S. integrifolium) was performed. The eggplant lines were divided into the two subgroups of delphinidin-3-rutinoside (D3R) and nasunin (NAS) typologies, on the basis of the anthocyanin detected in their fruit skin. The allied species had higher glycoalkaloids content, lower soluble solids and PPO activity and absence of anthocyanins compared to the eggplant lines; S. sodomaeum stood out for high phenols content. Orthogonal contrast revealed a higher sugar content and low PPO activity in NAS- compared to D3R-typologies, whereas higher chlorogenic acid and anthocyanin contents were present in D3R-typologies. The main effect of the ripening was a decrease in phenols and in the PPO activity, not evidenced in S. sodomaeum, and an increase of glycoalkaloids in overripe fruits.A good relationship was found between superoxide anion scavenging capacity and chlorogenic acid. This study highlighted the pattern of accumulation, also evidencing variations, of several phytochemicals during the eggplant fruit development and ripening.

Development and validation of HPLC method for analysis of dexamethasone acetate in microemulsions

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Performance characteristics of bioassay UV-spectrophotometry and high perfomance liquid chromatographic determination of gatifloxacin in tablets

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Performance characteristics of high performance liquid chromatography, first order derivative UV spectrophotometry and bioassay for fluconazole determination in capsules

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Cocaine induces cell death and activates the transcription nuclear factor kappa-b in pc12 cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)