Detection of millimetric deformation using a terrestrial laser scanner: experiment and application to a rockfall event

Terrestrial laser scanning (TLS) is one of the most promising surveying techniques for rockslope characterization and monitoring. Landslide and rockfall movements can be detected by means of comparison of sequential scans. One of the most pressing challenges of natural hazards is combined temporal and spatial prediction of rockfall. An outdoor experiment was performed to ascertain whether the TLS instrumental error is small enough to enable detection of precursory displacements of millimetric magnitude. This consists of a known displacement of three objects relative to a stable surface. Results show that millimetric changes cannot be detected by the analysis of the unprocessed datasets. Displacement measurement are improved considerably by applying Nearest Neighbour (NN) averaging, which reduces the error (1¿) up to a factor of 6. This technique was applied to displacements prior to the April 2007 rockfall event at Castellfollit de la Roca, Spain. The maximum precursory displacement measured was 45 mm, approximately 2.5 times the standard deviation of the model comparison, hampering the distinction between actual displacement and instrumental error using conventional methodologies. Encouragingly, the precursory displacement was clearly detected by applying the NN averaging method. These results show that millimetric displacements prior to failure can be detected using TLS.

Rockfall monitoring by Terrestrial Laser Scanning ¿ case study of the basaltic rock face at Castellfollit de la Roca (Catalonia, Spain)

This case study deals with a rock face monitoring in urban areas using a Terrestrial Laser Scanner. The pilot study area is an almost vertical, fifty meter high cliff, on top of which the village of Castellfollit de la Roca is located. Rockfall activity is currently causing a retreat of the rock face, which may endanger the houses located at its edge. TLS datasets consist of high density 3-D point clouds acquired from five stations, nine times in a time span of 22 months (from March 2006 to January 2008). The change detection, i.e. rockfalls, was performed through a sequential comparison of datasets. Two types of mass movement were detected in the monitoring period: (a) detachment of single basaltic columns, with magnitudes below 1.5 m3 and (b) detachment of groups of columns, with magnitudes of 1.5 to 150 m3. Furthermore, the historical record revealed (c) the occurrence of slab failures with magnitudes higher than 150 m3. Displacements of a likely slab failure were measured, suggesting an apparent stationary stage. Even failures are clearly episodic, our results, together with the study of the historical record, enabled us to estimate a mean detachment of material from 46 to 91.5 m3 year¿1. The application of TLS considerably improved our understanding of rockfall phenomena in the study area.

Examination of Heterogeneous Crossing Sequences Between Toner and Rollerball Pen Strokes by Digital Microscopy and 3-D Laser Profilometry

The determination of line crossing sequences between rollerball pens and laser printers presents difficulties that may not be overcome using traditional techniques. This research aimed to study the potential of digital microscopy and 3-D laser profilometry to determine line crossing sequences between a toner and an aqueous ink line. Different paper types, rollerball pens, and writing pressure were tested. Correct opinions of the sequence were given for all case scenarios, using both techniques. When the toner was printed before the ink, a light reflection was observed in all crossing specimens, while this was never observed in the other sequence types. The 3-D laser profilometry, more time-consuming, presented the main advantage of providing quantitative results. The findings confirm the potential of the 3-D laser profilometry and demonstrate the efficiency of digital microscopy as a new technique for determining the sequence of line crossings involving rollerball pen ink and toner. With the mass marketing of laser printers and the popularity of rollerball pens, the determination of line crossing sequences between such instruments is encountered by forensic document examiners. This type of crossing presents difficulties with optical microscopic line crossing techniques involving ballpoint pens or gel pens and toner (1-4). Indeed, the rollerball's aqueous ink penetrates through the toner and is absorbed by the fibers of the paper, leaving the examiner with the impression that the toner is above the ink even when it is not (5). Novotny and Westwood (3) investigated the possibility of determining aqueous ink and toner crossing sequences by microscopic observation of the intersection before and after toner removal. A major disadvantage of their study resides in destruction of the sample by scraping off the toner line to see what was underneath. The aim of this research was to investigate the ways to overcome these difficulties through digital microscopy and three-dimensional (3-D) laser profilometry. The former was used as a technique for the determination of sequences between gel pen and toner printing strokes, but provided less conclusive results than that of an optical stereomicroscope (4). 3-D laser profilometry, which allows one to observe and measure the topography of a surface, has been the subject of a number of recent studies in this area. Berx and De Kinder (6) and Schirripa Spagnolo (7,8) have tested the application of laser profilometry to determine the sequence of intersections of several lines. The results obtained in these studies overcome disadvantages of other methods applied in this area, such as scanning electron microscope or the atomic force microscope. The main advantages of 3-D laser profilometry include the ease of implementation of the technique and its nondestructive nature, which does not require sample preparation (8-10). Moreover, the technique is reproducible and presents a high degree of freedom in the vertical axes (up to 1000 μm). However, when the paper surface presents a given roughness, if the pen impressions alter the paper with a depth similar to the roughness of medium, the results are not always conclusive (8). It becomes difficult in this case to distinguish which characteristics can be imputed to the pen impressions or the quality of the paper surface. This important limitation is assessed by testing different types of paper of variable quality (of different grammage and finishing) and the writing pressure. The authors will therefore assess the limits of 3-D laser profilometry technique and determine whether the method can overcome such constraints. Second, the authors will investigate the use of digital microscopy because it presents a number of advantages: it is efficient, user-friendly, and provides an objective evaluation and interpretation.

KRAB-zinc finger proteins and KAP1 can mediate long-range transcriptional repression through heterochromatin spreading.

Krüppel-associated box domain-zinc finger proteins (KRAB-ZFPs) are tetrapod-specific transcriptional repressors encoded in the hundreds by the human genome. In order to explore their as yet ill-defined impact on gene expression, we developed an ectopic repressor assay, allowing the study of KRAB-mediated transcriptional regulation at hundreds of different transcriptional units. By targeting a drug-controllable KRAB-containing repressor to gene-trapping lentiviral vectors, we demonstrate that KRAB and its corepressor KAP1 can silence promoters located several tens of kilobases (kb) away from their DNA binding sites, with an efficiency which is generally higher for promoters located within 15 kb or less. Silenced promoters exhibit a loss of histone H3-acetylation, an increase in H3 lysine 9 trimethylation (H3K9me3), and a drop in RNA Pol II recruitment, consistent with a block of transcriptional initiation following the establishment of silencing marks. Furthermore, we reveal that KRAB-mediated repression is established by the long-range spreading of H3K9me3 and heterochromatin protein 1 beta (HP1beta) between the repressor binding site and the promoter. We confirm the biological relevance of this phenomenon by documenting KAP1-dependent transcriptional repression at an endogenous KRAB-ZFP gene cluster, where KAP1 binds to the 3' end of genes and mediates propagation of H3K9me3 and HP1beta towards their 5' end. Together, our data support a model in which KRAB/KAP1 recruitment induces long-range repression through the spread of heterochromatin. This finding not only suggests auto-regulatory mechanisms in the control of KRAB-ZFP gene clusters, but also provides important cues for interpreting future genome-wide DNA binding data of KRAB-ZFPs and KAP1.

High Range Water Reducer in Portland Cement Concrete Made with D-Cracking Susceptible Coarse Aggregate, HR-1021, 1980

The objective of this research was to determine of the use of High Range Water Reducers (HRWR) (resulting in a lower water content ratio) with a D-cracking susceptible crushed limestone coarse aggregate would yield significant improvement in the durability.

Non-contact microdrilling of mouse zona pellucida with an objective-delivered 1.48-microns diode laser.

BACKGROUND and OBJECTIVE: A non-touch laser-induced microdrilling procedure is studied on mouse zona pellucida (ZP). STUDY DESIGN/MATERIALS and METHODS: A 1.48-microns diode laser beam is focused in a 8-microns spot through a 45x objective of an inverted microscope. Mouse zygotes, suspended in a culture medium, are microdrilled by exposing their ZP to a short laser irradiation and allowed to develop in vitro. RESULTS: Various sharp-edged holes can be generated in the ZP with a single laser irradiation. Sizes can be varied by changing irradiation time (3-100 ms) or laser power (22-55 mW). Drilled zygotes present no signs of thermal damage under light and scanning electron microscopy and develop as expected in vitro, except for a distinct eight-shaped hatching behavior. CONCLUSION: The microdrilling procedure can generate standardized holes in mouse ZP, without any visible side effects. The hole formation can be explained by a local photothermolysis of the protein matrix.

Long-term and long range migration of radioisotopes in terrestrial systems : mechanisms of radioisotopes (Cs, Sr, Pu, Am) mobilization in soils

Summary Artificial radionuclides were released in the environment during the atmospheric nuclear weapon tests and after accidental events involving nuclear industries. As a primary receptor of the deposition, the soil is a very sensitive compartment and understanding the interaction and migration of radionuclides within soils allows the development of scenario for the contamination risk of the population and of the environment. Most available field studies on radionuclides in soils only concern one or two isotopes, mostly 137Cs, and few physico-chemical soil parameters. The purpose of this study was a broader understanding of the radioecology of an Alpine valley. In a first part, we aimed to describe the depth distribution of 137Cs, 90Sr, 239+240Pu, and 241Am within different alpine soils and to identify some stable elements as indicators for accumulating layers. In the central part of the study, the goal was to investigate the repartition of ^Sr and 239Pu between the truly dissolved fraction and the colloidal fraction of the soil solutions and to identify the nature of colloids involved in the adsorption of ^Sr and 239Pu. These results were integrated in an "advection- sorption" transport model seeking to explain the migration of 239Pu and 90Sr within the soils and to assess the importance of colloidal transport for these two isotopes. A further aspect studied was the role of the competition between the radioisotopes (137Cs and 90Sr) and their stable chemical analogues (K and Ca) with respect to plant uptake by different plant species. The results on the depth distribution within the soils showed that 137Cs was mostly retained in the topsoil, to the exception of an organic-rich soil (Histosol 2) receiving important surface runoff, where migration down to a depth of 30 cm was observed. 137Cs depth distribution within the soils was similar to unsupported 210Pb depth distribution. The plant uptake of 137Cs clearly depended on the concentration of exchangeable potassium in the soils. Moreover, we showed that the 137Cs uptake by certain species of the taxonomic orders Poales and Rosales was more sensitive to the increase in exchangeable Κ compared to other orders. Strontium-90 was much more mobile in the soils than 137Cs and depth migration and accumulation in specific AI- and Fe-rich layers were found down to 30 cm. Copper and Ni showed accumulations in these same layers, indicating their potential to be used as indicators for the migration of ^Sr within the soils. In addition, we observed a 90Sr activity peak in the topsoil that can be attributable to recycling of 90Sr by plant uptake. We demonstrated for the first time that a part of 90Sr (at least 40%) was associated with the colloids in organic-rich soil solutions. Therefore, we predict a significant effect of the colloidal migration of ^Sr in organic-rich soil solutions. The plant uptake results for 90Sr indicated a phylogenetic effect between Non-Eudicot and Eudicots: the order Poales concentrating much less 90Sr than Eudicots do. Moreover, we were able to demonstrate that the sensitivity of the 90Sr uptake by 5 different Alpine plant species to the amount of exchangeable Ca was species-independent. Plutonium and 241Am accumulated in the second layer of all soils and only a slight migration deeper than 20 cm was observed. Plutonium and 241Am showed a similar depth distribution in the soils. The model results suggested that the present day migration of 239Pu was very slow and that the uptake by plants was negligible. 239Pu activities between 0.01 to 0.08 mBq/L were measured in the bulk soil solutions. Migration of 239Pu with the soil solution is dominated by colloidal transport. We reported strong evidences that humic substances were responsible of the sorption of 239Pu to the colloidal fraction of the soil solutions. This was reflected by the strong correlation between 239Pu concentrations and the content of (colloidal) organic matter in the soil solution. Résumé Certains radioéléments artificiels ont été disséminés dans l'environnement suite aux essais atmosphériques de bombes nucléaires et suite à des accidents impliquant les industries nucléaires. En tant que récepteur primaire de la déposition, le sol est un compartiment sensible et des connaissances sur les interactions et la migration des radioéléments dans le sol permettent de développer des modèles pour estimer la contamination de la population et de l'environnement. Actuellement, la plupart des études de terrain sur ce sujet concernent uniquement un ou deux radioéléments, surtout le 137Cs et peu d'études intègrent les paramètres du sol pour expliquer la migration des radioéléments. Le but général de cette étude était une compréhension étendue de la radio-écologie d'une vallée alpine. Notre premier objectif était de décrire la distribution en profondeur de 137Cs, ^Sr, 239+240pu et 241Am dans différents sols alpins en relation avec des éléments stables du sol, dans le but d'identifier des éléments stables qui pourraient servir d'indicateurs pour des horizons accumulateurs. L'objectif de la deuxième partie, qui était la partie centrale de l'étude, était d'estimer le pourcentage d'activité sous forme colloïdale du 239Pu et du 90Sr dans les solutions des sols. De plus nous avons déterminé la nature des colloïdes impliqués dans la fixation du ^Sr et 239Pu. Nous avons ensuite intégré ces résultats dans un modèle de transport développé dans le but de décrire la migration du 239Pu et 90Sr dans le sol. Finalement, nous avons étudié l'absorption de 137Cs et 90Sr par les plantes en fonction de l'espèce et de la compétition avec leur élément analogue stable (K et Ca). Les résultats sur la migration en profondeur du 137Cs ont montré que ce radioélément était généralement retenu en surface, à l'exception d'un sol riche en matière organique dans lequel nous avons observé une nette migration en profondeur. Dans tous les sols, la distribution en profondeur du 137Cs était corrélée avec la distribution du 210Pb. L'absorption du 137Cs par les plantes, était dépendante de la concentration en Κ échangeable dans le sol, le potassium étant un compétiteur. De plus, nous avons observé que les espèces ne réagissaient pas de la même manière aux variations de la concentration de Κ échangeable. En effet, les espèces appartenant aux ordres des Poales et des Rosales étaient plus sensibles aux variations de potassium échangeable dans le sol. Dans tous les sols Le 90Sr était beaucoup plus mobile que le 137Cs. En effet, nous avons observé des accumulations de 90Sr dans des horizons riches en Fe et Al jusqu'à 30 cm de profondeur. De plus, le Cu et le Ni montraient des accumulations dans les mêmes horizons que le 90Sr, indiquant qu'il pourrait être possible d'utiliser ces deux éléments comme analogues pour la migration du 90Sr. D'après le modèle développé, le pic de 90Sr dans les premiers centimètres du sol peut être attribué à du recyclage par les plantes. Le 90Sr en solution était principalement sous forme dissoute dans des solutions de sols peu organique (entre 60 et 100% de 90Sr dissous). Par contre, dans des solutions organiques, un important pourcentage de 90Sr (plus de 40%) était associé aux colloïdes. La migration colloïdale du 90Sr peut donc être significative dans des solutions organiques. Comme pour le 137Cs, l'absorption du 90Sr par les plantes dépendait de la concentration de son analogue chimique dans la fraction échangeable du sol. Par contre, les espèces de plantes étudiées avaient la même sensibilité aux variations de la concentration du calcium échangeable. Le plutonium et l'américium étaient accumulés dans le deuxième horizon du sol et nous avons observé seulement une faible migration plus profondément que 20 cm. Selon le modèle, la migration actuelle du plutonium est très lente et l'absorption par les plantes semble négligeable. Nous avons mesuré entre 0.01 et 0.08 mBq/L de 239Pu dans les solutions de sol brutes. La migration du plutonium par la solution du sol est due principalement aux colloïdes, probablement de nature humique. Résumé grand public Dans les années 1950 à 1960, l'environnement a été contaminé par des éléments radioactifs (radioéléments) artificiels provenant des essais des armes atomiques et de l'industrie nucléaire. En effet, durant ces années, les premiers essais de bombes atomiques se faisaient dans l'atmosphère, libérant de grandes quantités d'éléments radioactifs. De plus certains accidents impliquant l'industrie nucléaire civile ont contribué à la dissémination d'éléments radioactifs dans l'environnement. Ce fut par exemple le cas de l'accident de la centrale atomique de Tchernobyl en 1986 qui a causé une importante contamination d'une grande partie de l'Europe par le 137Cs. Lorsqu'ils sont libérés dans l'atmosphère, les radioéléments sont dispersés et transportés par les courants atmosphériques, puis peuvent être déposés dans l'environnement, principalement par les précipitations. Une fois déposés sur le sol, les radioéléments vont interagir avec les composants du sol et migrer plus ou moins vite. La connaissance des interactions des éléments radioactifs avec le sol est donc importante pour prédire les risques de contamination de l'environnement et de l'homme. Le but général de ce travail était d'évaluer la migration de différents éléments radioactifs (césium-137, strontium-90, plutonium et américium-241) à travers le sol. Nous avons choisi un site d'étude en milieu alpin (Val Piora, Tessin, Suisse), contaminé en radioéléments principalement par les retombées de l'accident de Tchernobyl et des essais atmosphériques de bombes atomiques. Dans un premier temps, nous avons caractérisé la distribution en profondeur des éléments radioactifs dans le sol et l'avons comparée à divers éléments stables. Cette comparaison nous a permit de remarquer que le cuivre et le nickel s'accumulaient dans les mêmes horizons du sol que le strontium-90 et pourraient donc être utilisés comme analogue pour la migration du strontium-90 dans les sols. Dans la plupart des sols étudiés, la migration du césium-137, du plutonium et de l'américium-241 était lente et ces radioéléments étaient donc accumulés dans les premiers centimètres du sol. Par contre, le strontium-90 a migré beaucoup plus rapidement que les autres radioéléments si bien qu'on observe des accumulations de strontium-90 à plus de 30 cm de profondeur. Les radioéléments migrent dans la solution du sol soit sous forme dissoute, soit sous forme colloïdale, c'est-à-dire associés à des particules de diamètre < Ιμηι. Cette association avec des colloïdes permet à des radioéléments peu solubles, comme le plutonium, de migrer plus rapidement qu'attendu. Nous avons voulu savoir quelle était la part de strontium-90 et plutonium associés à des colloïdes dans la solution du sol. Les résultats ont montré que le plutonium en solution était principalement associé à des colloïdes de type organique. Quant au strontium-90, ce dernier était en partie associé à des colloïdes dans des solutions de sol riches en matière organique, par contre, il était principalement sous forme dissoute dans les solutions de sol peu organiques. L'absorption de radioéléments par les plantes représente une voie importante pour le transfert vers la chaîne alimentaire, par conséquent pour la contamination de l'homme. Nous avons donc étudié le transfert du césium-137 et du strontium-90 de plusieurs sols vers différentes espèces de plantes. Les résultats ont montré que l'absorption des radioéléments par les plantes était liée à la concentration de leur analogue chimique (calcium pour le strontium-90 et potassium pour le césium- 137) dans la fraction échangeable du sol. De plus certaines espèces de plantes accumulent significativement moins de strontium-90.

Calculation of wood volume and stem taper using terrestrial single-image close-range photogrammetry and contemporary software tools

Abstract

Traitement au laser des trous maculaires [Laser treatment of macular holes]

OBJECTIVE: To study a new technic of laser treatment of macular holes. METHODS: 21 eyes with stage II-IV macular hole were treated with Argon-green laser. Pigment epithelium in the area of the hole was whitened with spots of 100-200 microns, 100-300 mW. We expected this treatment to create a cellular proliferation that could close and contract the hole. Follow-up after treatment ranged from 3 to 24 months (mean: 9.3 months). RESULTS: Within one month after treatment, the macular hole was closed in 7 eyes (33%) and partially closed in 5 eyes (24%). The visual acuity increased from 1 to 5 lignes (ETDRS chart) in 9 eyes (43%), it remained the same in 9 eyes (43%) and decreased from 1 to 2 lignes in 3 eyes (14%). CONCLUSION: Laser treatment of macular holes seems to be effective and could be proposed as an alternative to the patients who cannot be operated on by vitrectomy and gas tamponade.

Construction of a Bridge Floor Using High Range Water Reducer, Construction Report, HR-192, 1978

The use of a high range water reducer in bridge floors was initiated by an Iowa Highway Research Board project (HR-192) in 1977 for two basic reasons. One was to determine the feasibility of using a high range water reducer (HRWR) in bridge floor concrete using conventional concrete proportioning, transporting and finishing equipment. The second was to determine the performance and protective qualities against chloride intrusion of a dense concrete bridge floor by de-icing agents used on Iowa's highways during winter months. This project was basically intended to overcome some problems that developed in the original research project. The problems alluded to are the time limits from batching to finishing; use of a different type of finishing machine; need for supplemental vibration on the surface of the concrete during the screeding operation and difficulty of texturing. The use of a double oscillating screed finishing machine worked well and supplemental vibration on one of the screeds was not needed. The limit of 45 minutes from batching the concrete to placement on the deck was verified. This is a maximum when the HRWR is introduced at the batch plant. The problem of texturing was not solved completely but is similar to our problems on the dense "Iowa System" overlay used on bridge deck repair projects. This project reinforced some earlier doubts about using truck transit mixers for mixing and transporting concrete containing HRWR when introduced at the batch plant.

Aplicaciones del laser de baja potencia en odontologia

La utilización de la tecnología láser en Odontología ha tenido una constante evolución y desarrollo. Con este trabajo se pretende hacer una actualización desde un punto de vista crítico, científico y objetivo de los avances y aplicaciones que se han publicado sobre el láser de baja potencia en el ámbito de cada una de las especialidades odontológicas. Asimismo, se exponen sus características, las normas de seguridad necesarias para su utilización, sus efectos secundarios y sus contraindicaciones.

Aplicaciones del laser de diodo en odontologia

El láser de diodo tiene numerosas aplicaciones en la especialidad de Cirugía Bucal siendo utilizado preferentemente para realizar intervenciones quirúrgicas sobre los tejidos blandos siempre que no impliquen un excesivo sangrado. En Endodoncia, Implantología Bucofacial y Periodoncia se emplea por su importante efecto bactericida. También se utiliza en procedimientos de blanqueamiento dentario. Es importante controlar adecuadamente el tiempo de aplicación y la potencia de trabajo para evitar el sobrecalentamiento de los tejidos vecinos, lo que produciría su necrosis. Siempre que se utilice el láser de diodo se debe efectuar la protección ocular recomendada tanto para el profesional, sus ayudantes y personal auxiliar, como para el paciente.