Plastic Deformation Of Nanocrystalline Nickel

A high-resolution electron microscopy study has uncovered the plastic behavior of accommodating large strains in nanocrystalline (NC) Ni subject to cold rolling at liquid nitrogen temperature. The activation of grain-boundary-mediated-plasticity is evidenced in NC-Ni, including twinning and formation of stacking fault via partial dislocation slips from the grain boundary. The formation and storage of 60A degrees full dislocations are observed inside NC-grains. The grain/twin boundaries act as the barriers of dislocation slips, leading to dislocation pile-up, severe lattice distortion, and formation of sub-grain boundary. The vicinity of grain/twin boundary is where defects preferentially accumulate and likely the favorable place for onset of plastic deformation. The present results indicate the heterogeneous and multiple natures of accommodating plastic strains in NC-grains.

Deformation Of Pdms Membrane And Microcantilever By A Water Droplet: Comparison Between Mooney-Rivlin And Linear Elastic Constitutive Models

In this paper, we studied the role of vertical component Of Surface tension of a water droplet on the deformation of membranes and microcantilevers (MCLs) widely used in lab-on-a-chip and micro-and nano-electromechanical system (MEMS/NEMS). Firstly, a membrane made of a rubber-like material, poly(dimethylsiloxane) (PDMS), was considered. The deformation was investigated using the Mooney-Rivlin (MR) model and the linear elastic constitutive relation, respectively. By comparison between the numerical solutions with two different models, we found that the simple linear elastic model is accurate enough to describe such kind of problem, which would be quite convenient for engineering applications. Furthermore, based on small-deflection beam theory, the effect of a liquid droplet on the deflection of a MCL was also studied. The free-end deflection of the MCL was investigated by considering different cases like a cylindrical droplet, a spherical droplet centered on the MCL and a spherical droplet arbitrarily positioned on the MCL. Numerical simulations demonstrated that the deflection might not be neglected, and showed good agreement with our theoretical analyses. (C) 2008 Elsevier Inc. All rights reserved.

Vergleichende Texturuntersuchungen an Filets von Kliesche (Limanda limanda) und Scholle (Pleuronectes platessa) in Abhängigkeit von Eislagerzeit post mortem, TK-Lagerung und Erhitzen

Instrumental investigations of texture have been performed using texture profile analysis. The following textural parameters have been assessed: hardness, gumminess, chewiness, springiness, cohesiveness and adhesiveness. The fillets of both species have been prepared from deep frozen headed and gutted raw material without fins after frozen storage of 0, 23 and 34 weeks, respectively. Deep freezing of fishes has been performed on board immediately after hauling or after 6 day’s storage in ice. Before texture measurement the raw material has been thawed and the measurement was carriedout on both thawed and microwave-heated fillets. In general, it can be concluded that both fish species are comparable in their texture parameters. The hardness of heated dab has been slightly higher comparing with that one of plaice. All other texture parameters showed a fairly good conformity between both species. While the hardness of dab increased during heating, it was decreasing in plaice. This was the only one significant difference between both fishes during heating. Adhesiveness as well as cohesiveness increased remarkably during heating. Changes effected by ice storage were only slight. Frozen storage, in contrast, caused a significant decrease of adhesiveness measured after heating the fillets of both species.

On the origin of shear banding instability in metallic glasses

To uncover the physical origin of shear-banding instability in metallic glass (MG), a theoretical description of thermo-mechanical deformation of MG undergoing one-dimensional simple shearing is presented. The coupled thermo-mechanical model takes into account the momentum balance, the energy balance and the dynamics of free volume. The interplay between free-volume production and temperature increase being two potential causes for shear-banding instability is examined on the basis of the homogeneous solution. It is found that the free-volume production facilitates the sudden increase in the temperature before instability and vice versa. A rigorous linear perturbation analysis is used to examine the inhomogeneous deformation, during which the onset criteria and the internal length and time scales for three types of instabilities, namely free-volume softening, thermal softening and coupling softening, are clearly revealed. The shear-banding instability originating from sole free-volume softening takes place easier and faster than that due to sole thermal softening, and dominates in the coupling softening. Furthermore, the coupled thermo-mechanical shear-band analysis does show that an initial slight distribution of local free volume can incur significant strain localization, producing a shear band. During such a localization process, the local free-volume creation occurs indeed prior to the increase in local temperature, indicating that the former is the cause of shear localization, whereas the latter is its consequence. Finally, extension of the above model to include the shear-induced dilatation shows that such dilatation facilitates the shear instability in metallic glasses.

Formation of Single and Multiple Deformation Twins in Nanocrystalline fcc Metals

Deformation twins are often observed to meet each other to form multi-fold twins in nanostructured face-centered cubic (fcc) metals.Here we propose two types of mechanism for the nucleation and growth of four different single and multiple twins. These mechanisms provide continuous generation of twinning partials for the growth of the twins after ucleation. A relatively high stress or high strain rate is needed to activate these mechanisms, making them more prevalent in nanocrystalline materials than in their coarse-grained counterparts.Experimental observations that support the proposed mechanisms are presented.

Growth of deformation twins in room-temperature rolled nanocrystalline nickel

Deformation twinning has been observed in room-temperature rolled nanocrystalline Ni. The growth of the deformation twins via the emission of partial dislocations from a grain boundary has been examined in detail. Partial dislocations on neighboring slip planes may migrate for different distances and then remain in the grain interior, leading to the formation of a steplike twin boundary TB . With continued twin growth, the TBs become gradually distorted and lose their coherent character due to accumulated high stresses. Moreover, we propose that microtwins may form near such TBs due to the emission of partial dislocations from the TB.

Elastic deformation of soft membrane with finite thickness induced by a sessile liquid droplet

In this paper, the role of vertical component of Surface tension of a droplet on the elastic deformation of a finite-thickness flexible membrane was theoretically analyzed using Hankel transformation. The vertical displacement at the Surface was derived and can be reduced to Lester's or Rusanov's solutions when the thickness is infinite. Moreover, some Simulations of the effect of a liquid droplet on a membrane with a finite thickness were made. The numerical results showed that there exists a saturated membrane thickness of the order of millimeter, when the thickness of a membrane is larger than such a value, the membrane can be regarded as a half-infinite body. Further numerical calculations for soft membrane whose thickness is far below the saturated thickness were made. By comparison between the maximum vertical displacement of an ultrathin soft membrane and a half-infinite body, we found that Lester's or Rusanov's solutions for a half-infinite body cannot correctly describe Such cases. In other words, the thickness of a soft membrane has great effect on the surface deformation of the ultrathin membrane induced by a liquid droplet. (C) 2009 Elsevier Inc. All rights reserved.

Shape effects on the yield stress and deformation of silicon nanowires: A molecular dynamics simulation

The tension and compression of single-crystalline silicon nanowires (SiNWs) with different cross-sectional shapes are studied systematically using molecular dynamics simulation. The shape effects on the yield stresses are characterized. For the same surface to volume ratio, the circular cross-sectional SiNWs are stronger than the square cross-sectional ones under tensile loading, but reverse happens in compressive loading. With the atoms colored by least-squares atomic local shear strain, the deformation processes reveal that the failure modes of incipient yielding are dependent on the loading directions. The SiNWs under tensile loading slip in {111} surfaces, while the compressive loading leads the SiNWs to slip in the {110} surfaces. The present results are expected to contribute to the design of the silicon devices in nanosystems.

Post-larval feeding of Clarias gariepinus (Burchell, 1802) on cultured zooplankton and artemia diets

The findings are presented of a study undertaken to provide baseline information that may be employed to develop a simplified hatchery technique for postlarval feeding of Clarias gariepinus on zooplankton cultured indoors in small aquaria. Three series of experiments were undertaken to identify the type and quantity of organic manure that would produce maximum densities of zooplankton in the shortest time in indoor cultures. Results suggest the possibility of the culture of natural zooplankton populations for use in larval feeding of C. gariepinus fry. Its effective hatchery application would bring about reduction in the unit cost per fingerling and ensure continuous hatchery operations even in the absence of Artemia cysts

Numerical Simulation of Liquefaction Deformation of Sand Layer around Bucket Foundations under Dynamic Loadings

Bucket Foundations under Dynamic Loadings The liquefaction deformation of sand layer around a bucket foundation is simulated under equivalent dynamic ice-induced loadings. A simplified numerical model is presented by taking the bucket-soil interaction into consideration. The development of vertical and horizontal liquefaction deformations are computed under equivalent dynamic ice-induced loadings. Firstly, the numerical model and results are proved to be reliable by comparing them with the centrifuge testing results. Secondly, the factors and the development characteristics of liquefaction deformation are analyzed. Finally, the following numerical simulation results are obtained: the liquefaction deformation of sand layer increases with the increase of loading amplitude and with the decrease of loading frequency and sand skeleton’s strength. The maximum vertical deformation is located on the sand layer surface and 1/4 times of the bucket’s height apart from the bucket’s side wall (loading boundary). The maximum horizontal deformation occurs at the loading boundary. When the dynamic loadings is applied for more than 5 hours, the vertical deformation on the sand layer surface reaches 3 times that at the bottom, and the horizontal deformation at 2.0 times of the bucket height apart from the loading boundary is 3.3% of which on the loading boundary.

Assessment of post-harvest losses in Nigeria fishery: the Kainji Lake model

The paper provides a description of a methodology used for quantitative assessment of post harvest losses in the Kainji Lake Fishery (Nigeria). The sample population was made up of 314 fisherfolk, 115 processors, 125 fish buyers and 111 fish sellers. For the determination of handling losses, 24,839 fishes weighing 2,389.31 kg belonging to 43 species were examined of which 10% by number and 9% by weight deteriorated at checking and 4% by number and 3% by weight at landing. Processing losses recorded 22% by number and 16% by weight deteriorated prior to and during smoking with the traditional 'Banda' kiln. During marketing, 16% of fish sold had deteriorated and 6% by weight of fish bought also deteriorated, mainly due to insect infestation during storage. Based on the 1995 yield estimate for Kainji Lake fishery, approximately 1000 tons of fish estimated at 80 million Naira were lost during handling alone. This figure would be much higher if the level of losses during processing and marketing are included. This assessment technique is recommended for use in obtaining quantifiable data on post harvest losses from other water bodies in Nigeria

A preliminary investigation into the post harvest losses of fish in Shiroro Lake area

The findings are presented of a study conducted to assess the post harvest losses in Shiroro Lake, Nigeria. The major objectives were to identify and quantify the types of losses, to provide recommendations that would enhance formulation of policy guidelines for utilization and exploitation of the declining fishery resources of the lake

Post harvest losses in the fisheries of Kainji Lake

An assessment is given of the post-harvest losses in the Lake Kainji fisheries of Nigeria. The study focussed on quantifiable information on post-harvest technology and post-harvest losses from fisherfolk, fish processors and fish traders operating within the Kainji Lake basin. The information was obtained from questionnaires sent to a total of 665 respondents, comprising 317 fishermen, 115 fish processors, 125 fish buyers, and 111 fish sellers in 45 fishing villages and collection centres within the lake basin. Considering the total catch from gillnets, longlines, traps and cast nets estimated at 14,000 in 1995 about 1,000 t of fish was either discarded or lost value due to spoilage during handling by fisherfolk. Assuming an average prices of 80 Naira/kg of fish, the loss to the economy amounted to 80 million Naira annually. Appropriate recommendations are made to significantly reduce post-harvest losses in the Kainji Lake fishery. (PDF contains 91 pages)