Estudo da síntese e sinterização de pós compósitos do sistema Ta-Cu

Ta-Cu bulk composites combine high mechanical resistance of the Ta with high electrical and thermal conductivity of the Cu. These are important characteristics to electrical contacts, microwave absorber and heat skinks. However, the low wettability of Ta under Cu liquid and insolubility mutual these elements come hard sintering this composite. High-energy milling (HEM) produces composite powders with high homogeneity and refines the grain size. This work focus to study Ta-20wt%Cu composite powders prepared by mechanical mixture and HEM with two different conditions of milling in a planetary ball mill and then their sintering using hydrogen plasma furnace and a resistive vacuum furnace. After milling, the powders were pressed in a steel dye at a pressure of 200 MPa. The cylindrical samples pressed were sintered by resistive vacuum furnace at 10-4torr with a sintering temperature at 1100ºC / 60 minutes and with heat rate at 10ºC/min and were sintered by plasma furnace with sintering temperatures at 550, 660 and 800ºC without isotherm under hydrogen atmosphere with heat rate at 80ºC/min. The characterizations of the powders produced were analyzed by scanning electron microscopy (SEM), x-ray diffraction (XRD) and laser granulometry. After the sintering the samples were analyzed by SEM, XRD and density and mass loss tests. The results had shown that to high intense milling condition produced composite particles with shorter milling time and amorphization of both phases after 50 hours of milling. The composite particles can produce denser structure than mixed powders, if heated above the Cu melting point. After the Cu to arrive in the melting point, liquid copper leaves the composite particles and fills the pores

Estudo da moagem de alta energia e sinterização de pós compósitos W-Cu

The Tungsten/copper composites are commonly used for electrical and thermal objectives like heat sinks and lectrical conductors, propitiating an excellent thermal and electrical conductivity. These properties are dependents of the composition, crystallite size and production process. The high energy milling of the powder of W-Cu produces an dispersion high and homogenization levels with crystallite size of W very small in the ductile Cu phase. This work discusses the effect of the HEM in preparation of the W-25Cu composite powders. Three techniques of powder preparation were utilized: milling the dry with powder of thick Cu, milling the dry with powder of fine Cu and milling the wet with powder of thick Cu. The form, size and composition of the particles of the powders milled were observed by scanning electron microscopy (SEM). The X-ray diffraction (XRD) was used to analyse the phases, lattice parameters, size and microstrain of the crystallite. The analyse of the crystalline structure of the W-25Cu powders milled made by Rietveld Method suggests the partial solid solubility of the constituent elements of the Cu in lattice of the W. This analyse shows too that the HEM produces the reduction high on the crystallite size and the increase in the lattice strain of both phases, this is more intense in the phase W

Estudo sobre o efeito dos parâmetros de processamento dos pós e sinterização do aço inox 316l reforçado com NbC

This masther dissertation presents a contribution to the study of 316L stainless steel sintering aiming to study their behavior in the milling process and the effect of isotherm temperature on the microstructure and mechanical properties. The 316L stainless steel is a widely used alloy for their high corrosion resistance property. However its application is limited by the low wear resistance consequence of its low hardness. In previous work we analyzed the effect of sintering additives as NbC and TaC. This study aims at deepening the understanding of sintering, analyzing the effect of grinding on particle size and microstructure and the effect of heating rate and soaking time on the sintered microstructure and on their microhardness. Were milled 316L powders with NbC at 1, 5 and 24 hours respectively. Particulates were characterized by SEM and . Cylindrical samples height and diameter of 5.0 mm were compacted at 700 MPa. The sintering conditions were: heating rate 5, 10 and 15◦C/min, temperature 1000, 1100, 1200, 1290 and 1300◦C, and soaking times of 30 and 60min. The cooling rate was maintained at 25◦C/min. All samples were sintered in a vacuum furnace. The sintered microstructure were characterized by optical and electron microscopy as well as density and microhardness. It was observed that the milling process has an influence on sintering, as well as temperature. The major effect was caused by firing temperature, followed by the grinding and heating rate. In this case, the highest rates correspond to higher sintering.

Influência do método de síntese e caracterização de pós compósitos de NiO- Ce1-xEuxO2-δ para anodos catalíticos de células a combustível

Fuel cells are electrochemical devices that convert chemical energy into electricity. Due to the development of new materials, fuel cells are emerging as generating clean energy generator. Among the types of fuel cells, categorized according to the electrode type, the solid oxide fuel cells (SOFC) stand out due to be the only device entirely made of solid particles. Beyond that, their operation temperature is relatively high (between 500 and 1000 °C), allowing them to operate with high efficiency. Another aspect that promotes the use of SOFC over other cells is their ability to operate with different fuels. The CeO2 based materials doped with rare earth (TR+3) may be used as alternatives to traditional NiO-YSZ anodes as they have higher ionic conductivity and smaller ohmic losses compared to YSZ, and can operate at lower temperatures (500-800°C). In the composition of the anode, the concentration of NiO, acting as a catalyst in YSZ provides high electrical conductivity and high electrochemical activity of reactions, providing internal reform in the cell. In this work compounds of NiO - Ce1-xEuxO2-δ (x = 0.1, 0.2 and 0.3) were synthesized from polymeric precursor, Pechini, method of combustion and also by microwave-assisted hydrothermal method. The materials were characterized by the techniques of TG, TPR, XRD and FEG-SEM. The refinement of data obtained by X-ray diffraction showed that all powders of NiO - Cex-1EuxO2-δ crystallized in a cubic phase with fluorite structure, and also the presence of Ni. Through the characterizations can be proved that all routes of preparation used were effective for producing ceramics with characteristics suitable for application as SOFC anodes, but the microwave-assisted hydrothermal method showed a significant reduction in the average grain size and improved control of the compositions of the phases

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Obtenção de pós de tântalo metálico a partir da redução aluminotérmica com ignição a plasma

Metallic tantalum has a high commercial value due to intrinsic properties like excellent ductility, corrosion resistance, high melt and boiling points and good electrical and thermal conductivities. Nowadays, it is mostly used in the manufacture of capacitors, due to excellent dielectric properties of its oxides. In the nature, tantalum occurs in the form of oxide and it is extracted mainly from tantalite-columbite ores. The tantalum is usually produced by the reduction of its oxide, using reductants like carbon, silicon, calcium, magnesium and aluminum. Among these techniques, the aluminothermic reduction has been used as the industrial method to produce niobium, tantalum and their alloys, due to the easy removal of the Al and Al2O3 of the system, easing further refining. In conventional aluminothermic reduction an electrical resistance is used to trigger the reaction. This reaction self-propagates for all the volume of material. In this work, we have developed a novel technique of aluminothermic reduction that uses the hydrogen plasma to trigger the reaction. The results obtained by XRD, SEM and EDS show that is possible to obtain a compound rich in tantalum through this technique of aluminothermic reduction in the plasma reactor

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Termoterapia e quimioterapia de banana 'Prata-Anã' associadas à temperatura de armazenamento no controle de podridões em pós-colheita

O objetivo deste estudo foi avaliar o efeito da termoterapia (56 ºC por 6 min) e quimioterapia (propiconazole 250 ml.l-1) associado com temperatura de armazenamento (temperatura ambiente, 18 ºC e 13 ºC) no controle de podridões de bananas (Musa spp.) 'Prata-Anã' (AAB) em pós-colheita. Os tratamentos apresentaram diferenças significativas na percentagem de área lesionada por fruto, perda de peso e coloração externa da casca em todas as temperaturas de armazenamento. A quimioterapia e a combinação termoterapia e quimioterapia evitaram a manifestação de podridões nas três condições de armazenamento, enquanto a termoterapia reduziu a percentagem de área lesionada por fruto de 98% para 11% em temperatura ambiente, de 8% para 7% em 18 ºC e de 10% para 0% em 13 ºC, sendo mais eficiente sob a temperatura de 13 ºC. Frutos não tratados perderam 25%, 10% e 3% de peso e atingiram a cor 7, 5 e 1 em temperatura ambiente, 18 ºC e 13 ºC, respectivamente. Frutos tratados com termoterapia e quimioterapia perderam 24, 11 e 5% e 20, 10 e 3%, e atingiram índice médio de cor 4 e 3,5, respectivamente. O período de conservação foi estendido para 18, 24 e 45 dias em temperatura ambiente, 18 ºC e 13 ºC, respectivamente. A combinação dos métodos evitou a manifestação de podridões, reduziu a perda de peso e manteve a cor da casca e a qualidade dos frutos.

Termoterapia de banana 'Prata-Anã' no controle de podridões em pós-colheita

O objetivo desse estudo foi determinar a tolerância de banana (Musa spp.) 'Prata-Anã' (AAB) e do fungo Colletotrichum musae à termoterapia no controle de podridões em pós-colheita. Experimentos in vivo e in vitro foram instalados em delineamento inteiramente casualizado, seguindo um esquema fatorial 4x5 (temperatura x tempo). Os tratamentos consistiram na imersão dos frutos (buquês) e do fungo (esporos e micélio) em água aquecida a 47, 50, 53 e 56 ºC, durante 0, 3, 6, 9 e 12 min. A exposição dos frutos a 56 ºC durante 9 min causou escurecimento da casca nas extremidades dos frutos, porém, as características físicas e químicas dos frutos não foram alteradas pelos tratamentos. Frutos inoculados e tratados a 56 ºC durante 6 min não apresentaram podridões nem escurecimento da casca, enquanto aqueles não tratados apresentaram 64% da área lesionada / fruto. A partir das combinações 53 ºC / 9 mi. e 56 ºC / 3 min a germinação de esporos foi reduzida para 4% e 0%, respectivamente. A combinação 56 ºC / 12 min reduziu, mas não paralisou o crescimento micelial. O tratamento 56 ºC / 6 min retardou mas não paralisou o crescimento micelial in vitro, porém foi efetivo no controle completo das podridões in vivo. Esse tratamento evitou a manifestação de podridões no inverno (maio), mas não no verão (novembro), mostrando-se influenciado pelas condições climáticas próximas à colheita dos cachos. A termoterapia pode ser recomendada para controle de podridão em pós-colheita de banana devendo ser ajustada para diferentes estações do ano.

Incidência de fungos em pós-colheita de banana 'Prata anã'(Musa AAB)

Este trabalho teve por objetivo determinar a ocorrência e a freqüência de fungos em banana 'Prata anã' e elucidar o agente causal das podridões em pós-colheita de frutos provenientes do norte de Minas Gerais. Dois métodos de isolamento foram adotados: diluição em placas, a partir da lavagem de frutos verdes, e direto de frutos maduros. Os fungos Colletotrichum musae, Trichoderma harzianum, Fusarium equisetii, Penicillium sp. Aspergillus parasiticus, Trichothecium roseum, Colletotrichum acutatum, Alternaria sp., Cladosporium musae e Curvularia lunata foram os mais freqüentemente associados aos frutos. A patogenicidade desses fungos foi testada pela substituição de discos da casca de frutos verdes por discos de micélio. Colletotrichum musae apresentou área média lesionada em torno do ponto de inoculação igual a 5,8 cm², enquanto para os demais fungos testados não passou de 1,50 cm². Os resultados mostraram que C. musae é o agente primário das podridões dos frutos examinados com 100 % de incidência e os demais fungos limitaram-se a necrosar os ferimentos em torno do ponto de inoculação. O modo de infecção latente, causada por C. musae, parece favorecer, primeiramente, a colonização interna dos tecidos e, posteriormente, a ação dos fungos oportunistas, que aceleram as podridões nos frutos e na coroa.

Evuloção cognitiva e funcional de pacientes pós-acidente vascular cerebral - AVC

PURPOSE: Stroke is a high-incidence cerebrovascular disease with elevated morbidity that results in impairments such as functional disabilities. This study aimed to investigate the functional evolution of individuals in the first six months post-stroke. METHOD: Longitudinal study with 42 stroke patients. The functional independence measure (FIM) and The National Institutes of Health Stroke Scale (NIHSS) were used by multidisciplinary staff 3 times in each participant; the first application was at admission to rehabilitation and the others three and six months later. RESULTS: Sample predominantly female (57%), married (52%), mean age 65.26 ±10.72 years, elementary schooling level (43%), ischemic stroke (91%), and right cerebral hemisphere (74%). Motor FIM scores and NIHSS scale showed improvement in the 3 evaluations, with significant p-value (<0.001). There was a strong relation between motor FIM evolution and NIHSS evolution (r = - 0.69 p-value< 0.001). CONCLUSIONS: It was observed that functional evolution at 6 months post-stroke was significant and the smaller the evolution of clinical impairment in these patients, the larger the evolution of their functional independence. The study is important because it allows a more appropriate therapeutic planning according with functional evolution in stroke rehabilitation

Síndrome metabólica e risco cardiovascular na pós- menopausa: avaliação por diferentes critérios diagnósticos e influência de fatores sócio-econômicos

The metabolic syndrome (MetS) involves a group of risk factors and is associated with a significantly higher risk of developing cardiovascular diseases (CVD) and type 2 diabetes. Recent studies have shown the importance of preventing CVD through early diagnosis and treatment of patients with MetS. The objective of our study was to determine the prevalence of MetS by different diagnostic criteria in postmenopausal women and analyze the influence of socioeconomic factors on cardiovascular risk in this sample of the population. A cross-sectional study involving 127 postmenopausal women (45 to 64 years) from Natal and Mossoró, Brazil. The study was approved by the Research Ethics Committee of the Federal University of Rio Grande do Norte. The experimental protocol consisted of applying structured interview, clinical examination and implementation of dosages blood. The diagnosis of MetS was based on NCEP-ATP III (National Cholesterol Education Program-Adult Treatment Panel III) and IDF (International Diabetes Federation) criteria. The research was accomplished with the participation of an interdisciplinary team in their several phases. The result of the sample studied had mean age of 53.9 ± 4.6 years and per capita income of 54.5 dollars. The prevalence of MetS, according to NCEP-ATP III and IDF criteria, was 52.8% and 61.4$, respectively. The agreement rate between NCEP-ATP III and IDF criteria was 81.9%, with a kappa value of 0.63 (CI 95%, 0.49-0.76), indicating good agreement between the two definitions. The most prevalent cardiovascular risk factor was HDL < 50 mg/dl, observed in 96.1% of the women analyzed, followed by increased waist circumference (≥ 80 cm) in 78.0%, elevated blood pressure in 51.2%, triglycerides ≥ 150 mg/dl in 40.9% and glycemia ≥ 100 mg/dl in 37.0% of the women. The occurrence of MetS was significantly associated with schooling and body mass index (BMI). High blood pressure was significantly associated with low family income, low schooling and weight gain. There was no significant association between the intensity of climacteric symptomatology and the occurrence of MetS. The conclusions of the research were that MetS and its individual components show a high prevalence in postmenopausal Brazilian women, and significant associations with weight gain and low socioeconomic indicators. The data point to the need for an interdisciplinary approach at the basic health care level, directed toward the early identification of risk factors and the promotion of cardiovascular health of climacteric women.

Avaliação da incontinência urinária de esforço em mulheres na pós-menopausa com e sem queixa de perda urinária através da aplicação do pad-test de 1 hora

Stress urinary incontinence (SUI) is defined as "involuntary loss of urine" due to several processes that alter the ability of the bladder to hold urine properly, regarded as a social and hygienic problem that adversely affects quality of life. In postmenopausal women, IU is associated with atrophy and weakness of the pelvic floor muscles. The objective this study was investigate, using the onehour pad test, stress urinary leakage (SUI), evaluate and compare their results in postmenopausal and premenopausal women. The survey was characterized as a cross-sectional study. The study consisted of 60 postmenopausal women were divided into GIU - consisting of 34 volunteers complaining of involuntary loss of urine during stress - and GSIU - consisting of 26 volunteers without complaints of loss of urine during stress, and 15 women, during the premenopausal (GPM), and ovulatory with normal menstrual cycle. All volunteers were evaluated clinically, subjected to one-hour pad test, after the biochemical evaluation of blood and sex hormones. Statistical analysis was performed by descriptive analysis, ANOVA, Turkey´s post-test and Pearson correlation. The results showed that 100% of postmenopausal patients had involuntary loss of urine during one hour pad test (GIU: 4.0 g; GSIU: 4.5 g). GPM remained continent after an hour pad test (GPM: 0.4 g). In addition, Pearson showed a strong correlation between urine loss with time since menopause (r = 0.8, p <0.01) and body mass index - BMI (r = 0.7; p = 0.01). These data suggest that the one-hour pad test is a useful test to assess and quantify urinary leakage, including those volunteers who had no previous complaint of SUI

Avaliação da eficácia analgésica no pós-operatório de revascularização do miocárdio: ensaio clínico randomizado controlado

A analgesia pós-operatória eficaz é especialmente importante após cirurgias torácicas, pois, além de aliviar a dor, facilita a retomada de atividades normais, incluindo a deambulação, a respiração e a tosse. Dessa forma, os objetivos deste estudo são: avaliar a eficácia analgésica da associação entre anestesia geral e raquianestesia com morfina e ropivacaína mais esquema multimodal em relação à anestesia geral e esquema multimodal em cirurgia de revascularização do miocárdio; analisar a eficácia analgésica da injeção subcutânea de lidocaína e analgesia multimodal na remoção de tubos torácicos em cirurgia de revascularização do miocárdio. A metodologia consiste em ensaio clínico randomizado, controlado, envolvendo 58 pacientes, de ambos os sexos, com idade média de 59,8  8,9 anos, estado físico ASA II e III. Os participantes foram alocados em dois grupos, sendo o GI composto por indivíduos submetidos à anestesia geral combinada à raquianestesia com morfina 400μg e 6 ml (30mg) a 8 ml (40mg) de ropivacaína a 0,5% e analgesia multimodal; já o GII foi composto por indivíduos submetidos à anestesia geral associada à analgesia multimodal. Foi avaliada a dor, ao despertar, nas primeiras 24 horas, e ao realizar exercício respiratório, ao retirar drenos de torácicos e o tempo para extubação. A análise estatística foi realizada pelos testes do Qui-quadrado e Teste t de Student e o teste de Fisher. O resultado obtido foi o seguinte: o GI apresentou menor intensidade de dor ao despertar (p= 0,001), nas primeiras 24 horas (p= 0,001) e durante a realização dos exercícios respiratórios (p= 0,004). Houve maior necessidade de analgesia complementar no grupo GII, com maior consumo de morfina (p= 0,05), e os efeitos colaterais leves, como náuseas (p= 0,001), vômito (p= 0,002), prurido (p= 0,030), predominaram no GI. Não houve diferença estatisticamente significante entre os grupos (P= 0,47), em relação à intensidade de dor na remoção dos drenos. Após as observações feitas, o estudo sugere que a anestesia geral combinada à raquianestesia com morfina associada à ropivacaína oferece melhor efeito analgésico no pós-operatório de cirurgia cardíaca. Adicionalmente, o estudo sugere que o efeito analgésico da injeção subcutânea de lidocaína 1% associado à analgesia multimodal não é eficaz