A novel approach to functionalise pristine unsized carbon fibre using in situ generated diazonium species to enhance interfacial shear strength

Complex molecules have been successfully grafted onto the surface of unsized carbon fibre, a heterogeneous material which is a challenge to functionalise. The in situ generation of highly reactive phenyldiazo-species from their corresponding anilines was employed to achieve this task. The success of an initial proof-of-concept study (bearing a nitro moiety) supported by X-ray Photoelectron Spectroscopy (XPS) and physical characterisation, led to the design and synthesis of a more complex compound possessing a pendant amine moiety which could theoretically react with an epoxide based resin. After attachment to unsized oxidised fibres, analysis by XPS of the resulting fibres (fluorine used as an XPS tag) indicated a marked difference in functionalisation success which was attributed to steric factors, shown to be critical in influencing the attachment of the phenyldiazo-intermediate to the carbon fibre surface. Analysis of key fibre performance parameters of these fibres showed no change in elastic modulus, strength, surface topography or microscopic roughness when compared to the control unsized oxidised fibres. The functionalised fibres did however show a large increase in coefficient of friction. Single fibre fragmentation tests indicated a marked increase in interfacial shear strength, which was attributed to the pendent amine functionalities interacting with the epoxy resin.

Qualitative spectroscopic characterization of the matrix-silane coupling agent interface across metal fibre reinforced ion exchange resin composite membranes

The characterization of novel metal reinforced electro-dialysis ion exchange membranes, for water desalination, by attenuated total reflectance Fourier transform infrared spectroscopy mapping is presented in this paper. The surface of the porous stainless steel fibre meshes was treated in order to enhance the amount of surface oxide groups and increase the material hydrophilicity. Then, the metal membranes were functionalized through a sol-gel reaction with silane coupling agents to enhance the affinity with the ion exchange resins and avoid premature metal oxidation due to redox reactions at the metal-polymer interface. Polished cross sections of the composite membranes embedded into an epoxy resin revealed interfaces between metallic frameworks and the silane layer at the interface with the ion exchange material. The morphology of the metal-polymer interface was investigated with scanning electron microscopy and Fourier transform infrared micro-spectroscopy. Fourier transform infrared mapping of the interfaces was performed using the attenuated total reflectance mode on the polished cross-sections at the Australian Synchrotron. The nature of the interface between the metal framework and the ion exchange resin was shown to be homogeneous and the coating thickness was found to be around 1 μm determined by Fourier transform infrared micro-spectroscopy mapping. The impact of the coating on the properties of the membranes and their potential for water desalination by electro-dialysis are also discussed.

A novel approach to the functionalisation of pristine carbon fibre using azomethine 1,3-dipolar cycloaddition

We demonstrate the utilisation of an azomethine 1,3-dipolar cycloaddition reaction with carbon fibre to graft complex molecules onto the fibre surface. In an effort to enhance the interfacial interaction of the fibre to the matrix, the functionalised fibres possessed a pendant amine that is able to interact with epoxy resins. Functionalisation was supported by X-ray photoelectron spectroscopy and the grafting process had no detrimental effects on tensile strength compared with the control (untreated) fibres. Also, microscopic roughness (as determined by atomic force microscopy) and fibre topography were unchanged after the described treatment process. This methodology complements existing methodology aimed at enhancing the surface of carbon fibres for advanced material applications while not compromising the desirable strength profile. Single-fibre fragmentation tests show a statistically significant decrease in fragment length compared with the control fibres in addition to transverse cracking within the curing resin, both of which indicate an enhanced interaction between fibre and resin.

Exposure to As(III) and As(V) changes the Ca²⁺-activation properties of the two major fibre types from the chelae of the freshwater crustacean Cherax destructor

Arsenic is a known carcinogen found in the soil in gold mining regions at concentrations thousands of times greater than gold. Mining releases arsenic into the environment and surrounding water bodies. The main chemical forms of arsenic found in the environment are inorganic arsenite (As(III)) and arsenate (As(V)). Yabbies (Cherax destructor) accumulate arsenic at levels comparable to those in the sediment of their environment but the effect on their physiological function is not known. The effects of arsenic exposure (10 ppm sodium arsenite, AsNaO2 - 5.7 ppm As(III)) and 10 ppm arsenic acid, Na2HAsO4·7H2O - 2.6 ppm As(V)) for 40 days on the contractile function of the two major fibre types from the chelae were determined. After exposure, individual fibres were isolated from the chela, "skinned" (membrane removed) and attached to the force recording apparatus. Contraction was induced in solutions containing increasing [Ca(2+)] until a maximum Ca(2+)-activation was obtained. Submaximal force responses were plotted as a percentage of the maximum Ca(2+)-activated force. As(V) exposure resulted in lower levels of calcium required for activation than As(III) indicating an increased sensitivity to Ca(2+) after long term exposure to arsenate compared to arsenite. Myosin heavy chain and tropomyosin content in individual fibres was also decreased as a result of arsenic exposure. Single fibres exposed to As(V) produced significantly more force than muscle fibres from control animals. Long-term exposure of yabbies to arsenic alters the contractile function of the two major fibre types in the chelae.

Shape morphing in fibre reinforced composite beams containing NiTi

The present research investigates the design, activation and modelling of a new generation of hybrid materials; called shape memory alloy-composites. These hybrid materials exhibit reversible bending motion with a temperature change and have the potential to be employed in aerospace, automotive and robotic application.

Functionalisation of carbon fibre toward enhanced fibre/matrix adhesion

This study developed new methodologies to enhance the performance of carbon fiber in epoxy-based composites. A unique interdisciplinary approach of organic chemistry and engineering resulting in excellent real world outcomes.

Wear of permanent incisors with age on commercial Australian Angora goat farms

OBJECTIVE: To quantify if, and to what extent, permanent incisor wear differed with age of goat and farm of origin on commercial Australian Angora goat farms. DESIGN: Observations were made on three Angora goat farms in the wheat-sheep zone of Victoria, each managed according to the farmer's practices. Farmers provided a representative flock of does. METHODS: The proportion and pattern of wear of permanent incisors were recorded and percentage wear calculated. After log(y + 10) transformation, a parsimonious general linear model was developed to relate wear to farm and age, with age considered as a continuous variate. RESULTS: The range in wear of the permanent incisors was 0-100%. For each farm, the most parsimonious model for permanent first incisor wear and average wear of all permanent incisors was a separate straight line relating the transformed incisor wear to the age of doe. The models accounted for 66-73% of variance. On each farm the incisor wear was similar and low for ages up to approximately 4 years. On all farms, the amount of incisor wear increased dramatically with age, although the rate of increase differed with each farm. CONCLUSIONS: Permanent incisor wear increased with age of goat and differed with farm of origin. Angora goat farmers need to be aware of the potential for incisor wear to affect doe production and health.

Fabric handle properties of superfine wool fabrics with different fibre curvature, cashmere content and knitting tightness

The handle properties of single jersey fabrics composed of superfine wools (17 μm) of different fibre curvature (114 vs. 74 °/mm) in blends with cashmere (fibre curvature 49 °/mm) were investigated. There were four blend ratios of cashmere (0, 25, 50, 75%) plus 100% cashmere. Each of the nine fibre blend combinations were replicated three times, and each was knitted into three tightness factors. The 81 fabrics were evaluated using the Wool HandleMeter, which measures seven primary handle attributes and Overall handle, and have been calibrated using a panel of experts and a wide variety of commercial fabrics. Results were analysed by ANOVA and general linear modelling. Tightness factor significantly affected all Wool HandleMeter attribute values, with the effect of tightness factor varying according to handle attribute. The Wool HandleMeter was able to detect differences between fabrics composed of superfine wool differing in fibre curvature, with lower fibre curvature wool fabrics having more preferred Overall handle and softer, looser, cooler, lighter and less dry handle attributes at some or all tightness factors compared with fabrics composed of higher fibre curvature superfine wool. Progressively blending cashmere with wool significantly improved Overall handle, increased soft and smooth handle, reduced dry, heavy and tight handle. Linear regression modelling indicated that fabric mass per unit area explained more than 50% of the variance in overall fabric handle and in combination with variations in fabric thickness and yarn elongation could explain 71% of the variance in Overall handle.

Effects of fibre parameters on the ultraviolet protection of fibre assemblies

Ultraviolet (UV) radiation protection is becoming increasingly necessary for human health, and textiles play an important role. The interaction between UV light and textiles is a complex one, involving fibre, yarn and fabric parameters. In this study, an optical model is presented for examining the influences of fibre parameters on the UV protection offered by a bundle of fibres with a given mass. The effects of mean fibre diameter and fibre type on UV absorption were examined. The model was verified with results of UV–visible diffuse reflectance measurements on natural and synthetic fibres. When the mass of fibres was kept constant, within the measurement range in this study, a bundle of fibres with coarser fibres had a lower UV reflectance than that with finer ones. The model accurately predicted factors influencing UV protection, including fibre diameter, fibre transmittance, porosity and refractive index.

Prestressed natural fibre spun yarn reinforced polymer-matrix composites

Abstract We report that a prestressing technique similar to that traditionally used in prestressed concrete can improve the mechanical performance of flax fibre spun yarn reinforced polymer-matrix composites. Prestressing a low twist yarn not only introduces tension to the constituent fibres and compressive stress to the matrix similar as in prestressed concretes, but also causes changes to the yarn structure that lead to the rearrangement of fibres within the yarn. Prestressing increases the fibre packing density in yarn, causes fibre straightening, and reduces fibre obliquity in yarn (improved fibre alignment along yarn axis). All these changes contribute positively to the mechanical properties of the natural fibre yarn reinforced composites. Crown

A systematic study of carbon fibre surface grafting via in situ diazonium generation for improved interfacial shear strength in epoxy matrix composites

A recently established means of surface functionalization of unsized carbon fibres for enhanced compatibility with epoxy resins was optimised and evaluated using interfacial shear stress measurements. Interfacial adhesion has a strong influence on the bulk mechanical properties of composite materials. In this work we report on the optimisation of our aryl diazo-grafting methodology via a series of reagent concentration studies. The fibres functionalised at each concentration are characterised physically (tensile strength, modulus, coefficient of friction, and via AFM), and chemically (XPS). The interfacial shear strength (IFSS) of all treated fibres was determined via the single fibre fragmentation test, using the Kelly-Tyson model. Large increases in IFSS for all concentrations (28-47%) relative to control fibres were observed. We show that halving the reagent concentration increased the coefficient of friction of the fibre and the interfacial shear strength of the composite while resulting in no loss of the key performance characteristics in the treated fibre.

Weathering, fibre strength and colour properties of processed white cashmere

Weathering refers to the degradation of wool fibres that occur during growth from exposure of the fleece to sunlight, water and air. Weathering damage to Merino wool reduces quantities of fibre that are harvested, reduces length in both raw and processed wools, reduces spinning performance and dyeing outcomes. This work aimed to aimed to quantify if and to what extent weathering occurred in 38 lots of commercial dehaired white cashmere and cashmere top sourced from traditional and new origins of production and the extent of any association between weathering and tensile strength properties of the dehaired cashmere and cashmere top. The cashmere was tested for physical properties, bundle tenacity and extension, tristimulus values brightness (Y) and yellowness (Y-Z) and reflectance. Dye uptake was used as an index of weathering. Linear models, relating to weathering, bundle tenacity and Y-Z were fitted to origin and other objective measurements. Mean attributes (range) were: mean fibre diameter, 17.0 μm (13.5–21.3 μm); bundle tenacity of tops, 10.3 cN/tex (8.3–12.9 cN/tex), for dehaired fibre, 10.1 cN/tex (9.1–11.4 cN/tex). Stain uptake varied from 0.92 to 6.34 mg/g fibre indicating a six-fold variation in the extent of weathering. Both the extent of weathering and the bundle tenacity of commercial lots of cashmere were affected by the origin of the cashmere. Increased weathering reduced bundle tenacity, bundle extension, increased the yellowness and reduced reflectance of white cashmere. Bundle tenacity of cashmere declined as fibre diameter variability increased from 20 to 22.5%. For the samples tested, the cashmere from China, Mongolia, Afghanistan and Iran showed more weathering than cashmere from Australia, New Zealand and the USA. The differences in the extent of weathering and of bundle tenacity between cashmere from different origins were of commercial significance.