Evaluation of APD and SiPM Matrices as Sensors for Monolithic PET Detector Block

Gamma detectors based on monolithic scintillator blocks coupled to APDs matrices have proved to be a good alternative to pixelated ones for PET scanners. They provide comparable spatial resolution, improve the sensitivity and make easier the mechanical design of the system. In this study we evaluate by means of Geant4-based simulations the possibility of replacing the APDs by SiPMs. Several commercial matrices of light sensors coupled to LYSO:Ce monolithic blocks have been simulated and compared. Regarding the spatial resolution and linearity of the detector, SiPMs with high photo detection efficiency could become an advantageous replacement for the APDs

Projector Model for Efficient List-Mode Reconstruction in PET Scanners with Parallel Planar Detectors

We have developed a new projector model specifically tailored for fast list-mode tomographic reconstructions in Positron emission tomography (PET) scanners with parallel planar detectors. The model provides an accurate estimation of the probability distribution of coincidence events defined by pairs of scintillating crystals. This distribution is parameterized with 2D elliptical Gaussian functions defined in planes perpendicular to the main axis of the tube of response (TOR). The parameters of these Gaussian functions have been obtained by fitting Monte Carlo simulations that include positron range, acolinearity of gamma rays, as well as detector attenuation and scatter effects. The proposed model has been applied efficiently to list-mode reconstruction algorithms. Evaluation with Monte Carlo simulations over a rotating high resolution PET scanner indicates that this model allows to obtain better recovery to noise ratio in OSEM (ordered-subsets, expectation-maximization) reconstruction, if compared to list-mode reconstruction with symmetric circular Gaussian TOR model, and histogram-based OSEM with precalculated system matrix using Monte Carlo simulated models and symmetries.

Applications for wireless sensor networks : tracking with binary proximity sensors

El interés cada vez mayor por las redes de sensores inalámbricos pueden ser entendido simplemente pensando en lo que esencialmente son: un gran número de pequeños nodos sensores autoalimentados que recogen información o detectan eventos especiales y se comunican de manera inalámbrica, con el objetivo final de entregar sus datos procesados a una estación base. Los nodos sensores están densamente desplegados dentro del área de interés, se pueden desplegar al azar y tienen capacidad de cooperación. Por lo general, estos dispositivos son pequeños y de bajo costo, de modo que pueden ser producidos y desplegados en gran numero aunque sus recursos en términos de energía, memoria, velocidad de cálculo y ancho de banda están enormemente limitados. Detección, tratamiento y comunicación son tres elementos clave cuya combinación en un pequeño dispositivo permite lograr un gran número de aplicaciones. Las redes de sensores proporcionan oportunidades sin fin, pero al mismo tiempo plantean retos formidables, tales como lograr el máximo rendimiento de una energía que es escasa y por lo general un recurso no renovable. Sin embargo, los recientes avances en la integración a gran escala, integrado de hardware de computación, comunicaciones, y en general, la convergencia de la informática y las comunicaciones, están haciendo de esta tecnología emergente una realidad. Del mismo modo, los avances en la nanotecnología están empezando a hacer que todo gire entorno a las redes de pequeños sensores y actuadores distribuidos. Hay diferentes tipos de sensores tales como sensores de presión, acelerómetros, cámaras, sensores térmicos o un simple micrófono. Supervisan las condiciones presentes en diferentes lugares tales como la temperatura, humedad, el movimiento, la luminosidad, presión, composición del suelo, los niveles de ruido, la presencia o ausencia de ciertos tipos de objetos, los niveles de tensión mecánica sobre objetos adheridos y las características momentáneas tales como la velocidad , la dirección y el tamaño de un objeto, etc. Se comprobara el estado de las Redes Inalámbricas de Sensores y se revisaran los protocolos más famosos. Así mismo, se examinara la identificación por radiofrecuencia (RFID) ya que se está convirtiendo en algo actual y su presencia importante. La RFID tiene un papel crucial que desempeñar en el futuro en el mundo de los negocios y los individuos por igual. El impacto mundial que ha tenido la identificación sin cables está ejerciendo fuertes presiones en la tecnología RFID, los servicios de investigación y desarrollo, desarrollo de normas, el cumplimiento de la seguridad y la privacidad y muchos más. Su potencial económico se ha demostrado en algunos países mientras que otros están simplemente en etapas de planificación o en etapas piloto, pero aun tiene que afianzarse o desarrollarse a través de la modernización de los modelos de negocio y aplicaciones para poder tener un mayor impacto en la sociedad. Las posibles aplicaciones de redes de sensores son de interés para la mayoría de campos. La monitorización ambiental, la guerra, la educación infantil, la vigilancia, la micro-cirugía y la agricultura son solo unos pocos ejemplos de los muchísimos campos en los que tienen cabida las redes mencionadas anteriormente. Estados Unidos de América es probablemente el país que más ha investigado en esta área por lo que veremos muchas soluciones propuestas provenientes de ese país. Universidades como Berkeley, UCLA (Universidad de California, Los Ángeles) Harvard y empresas como Intel lideran dichas investigaciones. Pero no solo EE.UU. usa e investiga las redes de sensores inalámbricos. La Universidad de Southampton, por ejemplo, está desarrollando una tecnología para monitorear el comportamiento de los glaciares mediante redes de sensores que contribuyen a la investigación fundamental en glaciología y de las redes de sensores inalámbricos. Así mismo, Coalesenses GmbH (Alemania) y Zurich ETH están trabajando en diversas aplicaciones para redes de sensores inalámbricos en numerosas áreas. Una solución española será la elegida para ser examinada más a fondo por ser innovadora, adaptable y polivalente. Este estudio del sensor se ha centrado principalmente en aplicaciones de tráfico, pero no se puede olvidar la lista de más de 50 aplicaciones diferentes que ha sido publicada por la firma creadora de este sensor específico. En la actualidad hay muchas tecnologías de vigilancia de vehículos, incluidos los sensores de bucle, cámaras de video, sensores de imagen, sensores infrarrojos, radares de microondas, GPS, etc. El rendimiento es aceptable, pero no suficiente, debido a su limitada cobertura y caros costos de implementación y mantenimiento, especialmente este ultimo. Tienen defectos tales como: línea de visión, baja exactitud, dependen mucho del ambiente y del clima, no se puede realizar trabajos de mantenimiento sin interrumpir las mediciones, la noche puede condicionar muchos de ellos, tienen altos costos de instalación y mantenimiento, etc. Por consiguiente, en las aplicaciones reales de circulación, los datos recibidos son insuficientes o malos en términos de tiempo real debido al escaso número de detectores y su costo. Con el aumento de vehículos en las redes viales urbanas las tecnologías de detección de vehículos se enfrentan a nuevas exigencias. Las redes de sensores inalámbricos son actualmente una de las tecnologías más avanzadas y una revolución en la detección de información remota y en las aplicaciones de recogida. Las perspectivas de aplicación en el sistema inteligente de transporte son muy amplias. Con este fin se ha desarrollado un programa de localización de objetivos y recuento utilizando una red de sensores binarios. Esto permite que el sensor necesite mucha menos energía durante la transmisión de información y que los dispositivos sean más independientes con el fin de tener un mejor control de tráfico. La aplicación se centra en la eficacia de la colaboración de los sensores en el seguimiento más que en los protocolos de comunicación utilizados por los nodos sensores. Las operaciones de salida y retorno en las vacaciones son un buen ejemplo de por qué es necesario llevar la cuenta de los coches en las carreteras. Para ello se ha desarrollado una simulación en Matlab con el objetivo localizar objetivos y contarlos con una red de sensores binarios. Dicho programa se podría implementar en el sensor que Libelium, la empresa creadora del sensor que se examinara concienzudamente, ha desarrollado. Esto permitiría que el aparato necesitase mucha menos energía durante la transmisión de información y los dispositivos sean más independientes. Los prometedores resultados obtenidos indican que los sensores de proximidad binarios pueden formar la base de una arquitectura robusta para la vigilancia de áreas amplias y para el seguimiento de objetivos. Cuando el movimiento de dichos objetivos es suficientemente suave, no tiene cambios bruscos de trayectoria, el algoritmo ClusterTrack proporciona un rendimiento excelente en términos de identificación y seguimiento de trayectorias los objetos designados como blancos. Este algoritmo podría, por supuesto, ser utilizado para numerosas aplicaciones y se podría seguir esta línea de trabajo para futuras investigaciones. No es sorprendente que las redes de sensores de binarios de proximidad hayan atraído mucha atención últimamente ya que, a pesar de la información mínima de un sensor de proximidad binario proporciona, las redes de este tipo pueden realizar un seguimiento de todo tipo de objetivos con la precisión suficiente. Abstract The increasing interest in wireless sensor networks can be promptly understood simply by thinking about what they essentially are: a large number of small sensing self-powered nodes which gather information or detect special events and communicate in a wireless fashion, with the end goal of handing their processed data to a base station. The sensor nodes are densely deployed inside the phenomenon, they deploy random and have cooperative capabilities. Usually these devices are small and inexpensive, so that they can be produced and deployed in large numbers, and so their resources in terms of energy, memory, computational speed and bandwidth are severely constrained. Sensing, processing and communication are three key elements whose combination in one tiny device gives rise to a vast number of applications. Sensor networks provide endless opportunities, but at the same time pose formidable challenges, such as the fact that energy is a scarce and usually non-renewable resource. However, recent advances in low power Very Large Scale Integration, embedded computing, communication hardware, and in general, the convergence of computing and communications, are making this emerging technology a reality. Likewise, advances in nanotechnology and Micro Electro-Mechanical Systems are pushing toward networks of tiny distributed sensors and actuators. There are different sensors such as pressure, accelerometer, camera, thermal, and microphone. They monitor conditions at different locations, such as temperature, humidity, vehicular movement, lightning condition, pressure, soil makeup, noise levels, the presence or absence of certain kinds of objects, mechanical stress levels on attached objects, the current characteristics such as speed, direction and size of an object, etc. The state of Wireless Sensor Networks will be checked and the most famous protocols reviewed. As Radio Frequency Identification (RFID) is becoming extremely present and important nowadays, it will be examined as well. RFID has a crucial role to play in business and for individuals alike going forward. The impact of ‘wireless’ identification is exerting strong pressures in RFID technology and services research and development, standards development, security compliance and privacy, and many more. The economic value is proven in some countries while others are just on the verge of planning or in pilot stages, but the wider spread of usage has yet to take hold or unfold through the modernisation of business models and applications. Possible applications of sensor networks are of interest to the most diverse fields. Environmental monitoring, warfare, child education, surveillance, micro-surgery, and agriculture are only a few examples. Some real hardware applications in the United States of America will be checked as it is probably the country that has investigated most in this area. Universities like Berkeley, UCLA (University of California, Los Angeles) Harvard and enterprises such as Intel are leading those investigations. But not just USA has been using and investigating wireless sensor networks. University of Southampton e.g. is to develop technology to monitor glacier behaviour using sensor networks contributing to fundamental research in glaciology and wireless sensor networks. Coalesenses GmbH (Germany) and ETH Zurich are working in applying wireless sensor networks in many different areas too. A Spanish solution will be the one examined more thoroughly for being innovative, adaptable and multipurpose. This study of the sensor has been focused mainly to traffic applications but it cannot be forgotten the more than 50 different application compilation that has been published by this specific sensor’s firm. Currently there are many vehicle surveillance technologies including loop sensors, video cameras, image sensors, infrared sensors, microwave radar, GPS, etc. The performance is acceptable but not sufficient because of their limited coverage and expensive costs of implementation and maintenance, specially the last one. They have defects such as: line-ofsight, low exactness, depending on environment and weather, cannot perform no-stop work whether daytime or night, high costs for installation and maintenance, etc. Consequently, in actual traffic applications the received data is insufficient or bad in terms of real-time owed to detector quantity and cost. With the increase of vehicle in urban road networks, the vehicle detection technologies are confronted with new requirements. Wireless sensor network is the state of the art technology and a revolution in remote information sensing and collection applications. It has broad prospect of application in intelligent transportation system. An application for target tracking and counting using a network of binary sensors has been developed. This would allow the appliance to spend much less energy when transmitting information and to make more independent devices in order to have a better traffic control. The application is focused on the efficacy of collaborative tracking rather than on the communication protocols used by the sensor nodes. Holiday crowds are a good case in which it is necessary to keep count of the cars on the roads. To this end a Matlab simulation has been produced for target tracking and counting using a network of binary sensors that e.g. could be implemented in Libelium’s solution. Libelium is the enterprise that has developed the sensor that will be deeply examined. This would allow the appliance to spend much less energy when transmitting information and to make more independent devices. The promising results obtained indicate that binary proximity sensors can form the basis for a robust architecture for wide area surveillance and tracking. When the target paths are smooth enough ClusterTrack particle filter algorithm gives excellent performance in terms of identifying and tracking different target trajectories. This algorithm could, of course, be used for different applications and that could be done in future researches. It is not surprising that binary proximity sensor networks have attracted a lot of attention lately. Despite the minimal information a binary proximity sensor provides, networks of these sensing modalities can track all kinds of different targets classes accurate enough.

Neutron spectrometry using artificial neural networks for a bonner sphere spectrometer with 3He detector

Neutron spectra unfolding and dose equivalent calculation are complicated tasks in radiation protection, are highly dependent of the neutron energy, and a precise knowledge on neutron spectrometry is essential for all dosimetry-related studies as well as many nuclear physics experiments. In previous works have been reported neutron spectrometry and dosimetry results, by using the ANN technology as alternative solution, starting from the count rates of a Bonner spheres system with a LiI(Eu) thermal neutrons detector, 7 polyethylene spheres and the UTA4 response matrix with 31 energy bins. In this work, an ANN was designed and optimized by using the RDANN methodology for the Bonner spheres system used at CIEMAT Spain, which is composed of a He neutron detector, 12 moderator spheres and a response matrix for 72 energy bins. For the ANN design process a neutrons spectra catalogue compiled by the IAEA was used. From this compilation, the neutrons spectra were converted from lethargy to energy spectra. Then, the resulting energy ?uence spectra were re-binned by using the MCNP code to the corresponding energy bins of the He response matrix before mentioned. With the response matrix and the re-binned spectra the counts rate of the Bonner spheres system were calculated and the resulting re-binned neutrons spectra and calculated counts rate were used as the ANN training data set.

Analysis of noise temperature sensitivity for the design of a broadband thermal noise primary standard

A broadband primary standard for thermal noise measurements is presented and its thermal and electromagnetic behaviour is analysed by means of a novel hybrid analytical?numerical simulation methodology. The standard consists of a broadband termination connected to a 3.5mm coaxial airline partially immersed in liquid nitrogen and is designed in order to obtain a low reflectivity and a low uncertainty in the noise temperature. A detailed sensitivity analysis is made in order to highlight the critical characteristics that mostly affect the uncertainty in the noise temperature, and also to determine the manufacturing and operation tolerances for a proper performance in the range 10MHz to 26.5 GHz. Aspects such as the thermal bead design, the level of liquid nitrogen or the uncertainties associated with the temperatures, the physical properties of the materials in the standard and the simulation techniques are discussed.

Liquid-crystal electro-optic modulator based on electrohydrodynamic effects

A new method of light modulation is reported. This method is based on the electro-optical properties of nematic materials and on the use of a new wedge structure. The advantages of this structure are the possibility of modulating nonpolarized light and the improved signal-to-noise ratio. The highest modulating frequency obtained is 25 kHz.

Análisis y diseño de un patrón de ruido térmico de 10 MHz a 26,5 GHz en tecnología coaxial

Esta Tesis Doctoral presenta las investigaciones y los trabajos desarrollados durante los años 2008 a 2012 para el análisis y diseño de un patrón primario de ruido térmico de banda ancha en tecnología coaxial. Para ubicar esta Tesis en su campo científico es necesario tomar conciencia de que la realización de mediciones fiables y trazables forma parte del sostenimiento del bienestar de una sociedad moderna y juega un papel crítico en apoyo de la competitividad económica, la fabricación y el comercio, así como de la calidad de vida. En el mundo moderno actual, una infraestructura de medición bien desarrollada genera confianza en muchas facetas de nuestra vida diaria, porque nos permite el desarrollo y fabricación de productos fiables, innovadores y de alta calidad; porque sustenta la competitividad de las industrias y su producción sostenible; además de contribuir a la eliminación de barreras técnicas y de dar soporte a un comercio justo, garantizar la seguridad y eficacia de la asistencia sanitaria, y por supuesto, dar respuesta a los grandes retos de la sociedad moderna en temas tan complicados como la energía y el medio ambiente. Con todo esto en mente se ha desarrollado un patrón primario de ruido térmico con el fin de aportar al sistema metrológico español un nuevo patrón primario de referencia capaz de ser usado para desarrollar mediciones fiables y trazables en el campo de la medida y calibración de dispositivos de ruido electromagnético de radiofrecuencia y microondas. Este patrón se ha planteado para que cumpla en el rango de 10 MHz a 26,5 GHz con las siguientes especificaciones: Salida nominal de temperatura de ruido aproximada de ~ 83 K. Incertidumbre de temperatura de ruido menor que ± 1 K en todo su rango de frecuencias. Coeficiente de reflexión en todo su ancho de banda de 0,01 a 26,5 GHz lo más bajo posible. Se ha divido esta Tesis Doctoral en tres partes claramente diferenciadas. La primera de ellas, que comprende los capítulos 1, 2, 3, 4 y 5, presenta todo el proceso de simulaciones y ajustes de los parámetros principales del dispositivo con el fin de dejar definidos los que resultan críticos en su construcción. A continuación viene una segunda parte compuesta por el capítulo 6 en donde se desarrollan los cálculos necesarios para obtener la temperatura de ruido a la salida del dispositivo. La tercera y última parte, capítulo 7, se dedica a la estimación de la incertidumbre de la temperatura de ruido del nuevo patrón primario de ruido obtenida en el capítulo anterior. Más concretamente tenemos que en el capítulo 1 se hace una exhaustiva introducción del entorno científico en donde se desarrolla este trabajo de investigación. Además se detallan los objetivos que se persiguen y se presenta la metodología utilizada para conseguirlos. El capítulo 2 describe la caracterización y selección del material dieléctrico para el anillo del interior de la línea de transmisión del patrón que ponga en contacto térmico los dos conductores del coaxial para igualar las temperaturas entre ambos y mantener la impedancia característica de todo el patrón primario de ruido. Además se estudian las propiedades dieléctricas del nitrógeno líquido para evaluar su influencia en la impedancia final de la línea de transmisión. En el capítulo 3 se analiza el comportamiento de dos cargas y una línea de aire comerciales trabajando en condiciones criogénicas. Se pretende con este estudio obtener la variación que se produce en el coeficiente de reflexión al pasar de temperatura ambiente a criogénica y comprobar si estos dispositivos resultan dañados por trabajar a temperaturas criogénicas; además se estudia si se modifica su comportamiento tras sucesivos ciclos de enfriamiento – calentamiento, obteniendo una cota de la variación para poder así seleccionar la carga que proporcione un menor coeficiente de reflexión y una menor variabilidad. En el capítulo 4 se parte del análisis de la estructura del anillo de material dieléctrico utilizada en la nota técnica NBS 1074 del NIST con el fin de obtener sus parámetros de dispersión que nos servirán para calcular el efecto que produce sobre el coeficiente de reflexión de la estructura coaxial completa. Además se realiza un estudio posterior con el fin de mejorar el diseño de la nota técnica NBS 1074 del NIST, donde se analiza el anillo de material dieléctrico, para posteriormente realizar modificaciones en la geometría de la zona donde se encuentra éste con el fin de reducir la reflexión que produce. Concretamente se estudia el ajuste del radio del conductor interior en la zona del anillo para que presente la misma impedancia característica que la línea. Y para finalizar se obtiene analíticamente la relación entre el radio del conductor interior y el radio de la transición de anillo térmico para garantizar en todo punto de esa transición la misma impedancia característica, manteniendo además criterios de robustez del dispositivo y de fabricación realistas. En el capítulo 5 se analiza el comportamiento térmico del patrón de ruido y su influencia en la conductividad de los materiales metálicos. Se plantean las posibilidades de que el nitrógeno líquido sea exterior a la línea o que éste penetre en su interior. En ambos casos, dada la simetría rotacional del problema, se ha simulado térmicamente una sección de la línea coaxial, es decir, se ha resuelto un problema bidimensional, aunque los resultados son aplicables a la estructura real tridimensional. Para la simulación térmica se ha empleado la herramienta PDE Toolbox de Matlab®. En el capítulo 6 se calcula la temperatura de ruido a la salida del dispositivo. Se parte del estudio de la aportación a la temperatura de ruido final de cada sección que compone el patrón. Además se estudia la influencia de las variaciones de determinados parámetros de los elementos que conforman el patrón de ruido sobre las características fundamentales de éste, esto es, el coeficiente de reflexión a lo largo de todo el dispositivo. Una vez descrito el patrón de ruido electromagnético se procede, en el capítulo 7, a describir los pasos seguidos para estimar la incertidumbre de la temperatura de ruido electromagnético a su salida. Para ello se utilizan dos métodos, el clásico de la guía para la estimación de la incertidumbre [GUM95] y el método de simulación de Monte Carlo. En el capítulo 8 se describen las conclusiones y lo logros conseguidos. Durante el desarrollo de esta Tesis Doctoral se ha obtenido un dispositivo novedoso susceptible de ser patentado, que ha sido registrado en la Oficina Española de Patentes y Marcas (O.E.P.M.) en Madrid, de conformidad con lo establecido en el artículo 20 de la Ley 11/1986, de 20 de Marzo, de Patentes, con el título Patrón Primario de Ruido Térmico de Banda Ancha (Referencia P-101061) con fecha 7 de febrero de 2011. ABSTRACT This Ph. D. work describes a number of investigations that were performed along the years 2008 to 2011, as a preparation for the study and design of a coaxial cryogenic reference noise standard. Reliable and traceable measurement underpins the welfare of a modern society and plays a critical role in supporting economic competitiveness, manufacturing and trade as well as quality of life. In our modern world, a well developed measurement infrastructure gives confidence in many aspects of our daily life, for example by enabling the development and manufacturing of reliable, high quality and innovative products; by supporting industry to be competitive and sustainable in its production; by removing technical barriers to trade and supporting fair trade; by ensuring safety and effectiveness of healthcare; by giving response to the major challenges in key sectors such energy and environment, etc. With all this in mind we have developed a primary standard thermal noise with the aim of providing the Spanish metrology system with a new primary standard for noise reference. This standard will allow development of reliable and traceable measurements in the field of calibration and measurement of electromagnetic noise RF and microwave devices. This standard has been designed to work in the frequency range from 10 MHz to 26.5 GHz, meeting the following specifications: 1. Noise temperature output is to be nominally ~ 83 K. 2. Noise temperature uncertainty less than ± 1 K in the frequency range from 0.01 to 26.5 GHz. 3. Broadband performance requires as low a reflection coefficient as possible from 0.01 to 26.5 GHz. The present Ph. D. work is divided into three clearly differentiated parts. The first one, which comprises Chapters 1 to 5, presents the whole process of simulation and adjustment of the main parameters of the device in order to define those of them which are critical for the manufacturing of the device. Next, the second part consists of Chapter 6 where the necessary computations to obtain the output noise temperature of the device are carried out. The third and last part, Chapter 7, is devoted to the estimation of the uncertainty related to the noise temperature of the noise primary standard as obtained in the preceding chapter. More specifically, Chapter 1 provides a thorough introduction to the scientific and technological environment where this research takes place. It also details the objectives to be achieved and presents the methodology used to achieve them. Chapter 2 describes the characterization and selection of the bead dielectric material inside the transmission line, intended to connect the two coaxial conductors equalizing the temperature between the two of them and thus keeping the characteristic impedance constant for the whole standard. In addition the dielectric properties of liquid nitrogen are analyzed in order to assess their influence on the impedance of the transmission line. Chapter 3 analyzes the behavior of two different loads and of a commercial airline when subjected to cryogenic working conditions. This study is intended to obtain the variation in the reflection coefficient when the temperature changes from room to cryogenic temperature, and to check whether these devices can be damaged as a result of working at cryogenic temperatures. Also we try to see whether the load changes its behavior after successive cycles of cooling / heating, in order to obtain a bound for the allowed variation of the reflection coefficient of the load. Chapter 4 analyzes the ring structure of the dielectric material used in the NBS technical note 1074 of NIST, in order to obtain its scattering parameters that will be used for computation of its effect upon the reflection coefficient of the whole coaxial structure. Subsequently, we perform a further investigation with the aim of improving the design of NBS technical note 1074 of NIST, and modifications are introduced in the geometry of the transition area in order to reduce the reflection it produces. We first analyze the ring, specifically the influence of the radius of inner conductor of the bead, and then make changes in its geometry so that it presents the same characteristic impedance as that of the line. Finally we analytically obtain the relationship between the inner conductor radius and the radius of the transition from ring, in order to ensure the heat flow through the transition thus keeping the same reflection coefficient, and at the same time meeting the robustness requirements and the feasibility of manufacturing. Chapter 5 analyzes the thermal behavior of the noise standard and its influence on the conductivity of metallic materials. Both possibilities are raised that the liquid nitrogen is kept outside the line or that it penetrates inside. In both cases, given the rotational symmetry of the structure, we have simulated a section of coaxial line, i.e. the equivalent two-dimensional problem has been resolved, although the results are applicable to the actual three-dimensional structure. For thermal simulation Matlab™ PDE Toolbox has been used. In Chapter 6 we compute the output noise temperature of the device. The starting point is the analysis of the contribution to the overall noise temperature of each section making up the standard. Moreover the influence of the variations in the parameters of all elements of the standard is analyzed, specifically the variation of the reflection coefficient along the entire device. Once the electromagnetic noise standard has been described and analyzed, in Chapter 7 we describe the steps followed to estimate the uncertainty of the output electromagnetic noise temperature. This is done using two methods, the classic analytical approach following the Guide to the Estimation of Uncertainty [GUM95] and numerical simulations made with the Monte Carlo method. Chapter 8 discusses the conclusions and achievements. During the development of this thesis, a novel device was obtained which was potentially patentable, and which was finally registered through the Spanish Patent and Trademark Office (SPTO) in Madrid, in accordance with the provisions of Article 20 of Law 11/1986 about Patents, dated March 20th, 1986. It was registered under the denomination Broadband Thermal Noise Primary Standard (Reference P-101061) dated February 7th, 2011.

Modelización y validación experimental del transporte de tritio en metal líquido y otros materiales para reactores de fusión nuclear magnética e inercial

La presente tesis se centra en el estudio de los fenómenos de transporte de los isótopos de hidrógeno, y más concretamente del tritio, en materiales de interés para los reactores de fusión nuclear. Los futuros reactores de fusión nuclear necesitarán una Planta de Tritio, con una envoltura regeneradora (breeding blanket) y unos sistemas auxiliares claves para su diseño. Por lo tanto su desarrollo y cualificación son cruciales para demostrar que los reactores de fusión son una opción viable como futura fuente de energía. Se han resaltado los diferentes retos de la difusión y retención de estas especies ligeras para cada sistema de la Planta de Tritio, y se han identificado las necesidades experimentales y paramétricas para abordar las simulaciones de difusión, como factores de transporte como la difusividad, absorción/desorción, solubilidad y atrapamiento. Se han estudiado los fenómenos de transporte y parámetros del T en el metal líquido LiPb, componente del breeding blanket tanto para una planta de fusión magnética como inercial. Para ello se han utilizado dos experimentos con características diversas, uno de ellos se ha llevado a cabo en un reactor de alto flujo, y por lo tanto, en condiciones de irradiación, y el otro sin irradiación. Los métodos de simulación numérica aplicados se han adaptado a los experimentos para las mediciones y para estudiar el régimen de transporte. En el estudio de estos experimentos se ha obtenido un valor para algunos de los parámetros claves en el transporte y gestión del tritio en el reactor. Finalmente se realiza un cálculo de la acumulación y difusión de tritio en una primera pared de tungsteno para un reactor de fusión inercial. En concreto para el proyecto de fusión por láser europeo, HiPER (para sus fases 4a y 4b). Se ha estudiado: la implantación de los isótopos de H y He en la pared de W tras una reacción de fusión por iluminación directa con un láser de 48MJ; el efecto en el transporte de T de los picos de temperatura en el W debido a la frecuencia de los eventos de fusión; el régimen de transporte en la primera pared. Se han identificado la naturaleza de las trampas más importantes para el T y se ha propuesto un modelo avanzado para la difusión con trampas. ABSTRACT The present thesis focuses into study the transport phenomenons of hydrogen isotopes, more specifically tritium, in materials of interest for nuclear fusion reactors. The future nuclear reactors will be provided of a Tritium Plant, with its breeding blanket and its auxiliary systems, all of them essential components for the plant. Therefore a reliable development and coalification are key issues to prove the viability of the nuclear fusion reactors as an energy source. The currently challenges for the diffusion and accumulation of these light species for each system of the TP has been studied. Experimental and theoretical needs have been identified and analyzed, specially from the viewpoint of the parameters. To achieve reliable simulations of tritium transport, parameters as diffusivity, absorption/desorption, solubility and trapping must be reliables. Transport phenomenon and parameters of T in liquid metal have been studied. Lead lithium is a key component of the breeding blanket, either in magnetic or inertial fusion confinement. Having this aim in mind, two experiments with different characteristics have been used; one of them has been realized in a high flux reactor, and hence, under irradiation conditions. The other one has been realized without radiation. The mathematical methods for the simulation have been adapted to the experiments, for the measures and also to study the transport behavior. A value for some key parameters for tritium management has been obtained in these studies. Finally, tritium accumulation and diffusion in a W first wall of an inertial nuclear fusion reactor has been assessed. A diffusion model of the implanted H, D, T and He species for the two initial phases of the proposed European laser fusion Project HiPER (namely, phase 4a and phase 4b) has been implemented using Tritium Migration Analysis Program, TMAP7. The effect of the prompt and working temperatures and the operational pulsing modes on the diffusion are studied. The nature of tritium traps in W and their performance has been analyzed and discussed.

Passive neutron area monitor with pairs of TLDs as neutron detector

A passive neutron area monitor has been designed using Monte Carlo methods; the monitor is a polyethylene cylinder with pairs of thermoluminescent dosimeters (TLD600 and TLD700) as thermal neutron detector. The monitor was calibrated with a bare and a thermalzed 241AmBe neutron sources and its performance was evaluated measuring the ambient dose equivalent due to photoneutrons produced by a 15 MV linear accelerator for radiotherapy and the neutrons in the output of a TRIGA Mark III radial beam port.

A clustering technique for partial discharge and noise sources identification in power cables by means of waveform parameters

On-line partial discharge (PD) measurements have become a common technique for assessing the insulation condition of installed high voltage (HV) insulated cables. When on-line tests are performed in noisy environments, or when more than one source of pulse-shaped signals are present in a cable system, it is difficult to perform accurate diagnoses. In these cases, an adequate selection of the non-conventional measuring technique and the implementation of effective signal processing tools are essential for a correct evaluation of the insulation degradation. Once a specific noise rejection filter is applied, many signals can be identified as potential PD pulses, therefore, a classification tool to discriminate the PD sources involved is required. This paper proposes an efficient method for the classification of PD signals and pulse-type noise interferences measured in power cables with HFCT sensors. By using a signal feature generation algorithm, representative parameters associated to the waveform of each pulse acquired are calculated so that they can be separated in different clusters. The efficiency of the clustering technique proposed is demonstrated through an example with three different PD sources and several pulse-shaped interferences measured simultaneously in a cable system with a high frequency current transformer (HFCT).

Detection of neuritic plaques in Alzheimer’s disease by magnetic resonance microscopy

Magnetic resonance microscopy (MRM) theoretically provides the spatial resolution and signal-to-noise ratio needed to resolve neuritic plaques, the neuropathological hallmark of Alzheimer’s disease (AD). Two previously unexplored MR contrast parameters, T2* and diffusion, are tested for plaque-specific contrast to noise. Autopsy specimens from nondemented controls (n = 3) and patients with AD (n = 5) were used. Three-dimensional T2* and diffusion MR images with voxel sizes ranging from 3 × 10−3 mm3 to 5.9 × 10−5 mm3 were acquired. After imaging, specimens were cut and stained with a microwave king silver stain to demonstrate neuritic plaques. From controls, the alveus, fimbria, pyramidal cell layer, hippocampal sulcus, and granule cell layer were detected by either T2* or diffusion contrast. These structures were used as landmarks when correlating MRMs with histological sections. At a voxel resolution of 5.9 × 10−5 mm3, neuritic plaques could be detected by T2*. The neuritic plaques emerged as black, spherical elements on T2* MRMs and could be distinguished from vessels only in cross-section when presented in three dimension. Here we provide MR images of neuritic plaques in vitro. The MRM results reported provide a new direction for applying this technology in vivo. Clearly, the ability to detect and follow the early progression of amyloid-positive brain lesions will greatly aid and simplify the many possibilities to intervene pharmacologically in AD.

Photoconductivity and Electro-Optical Properties of Wide Band Gap Metal Oxides

The PhD activity described in this Thesis was focused on the study of metal-oxide wide-bandgap materials, aiming at fabricating new optoelectronic devices such as solar-blind UV photodetectors, high power electronics, and gas sensors. Photocurrent spectroscopy and DC photocurrent time evolution were used to investigate the performance of prototypes under different atmospheres, temperatures and excitation wavelengths (or dark conditions). Cathodoluminescence, absorption spectroscopy, XRD and SEM were used to assess structural, morphologic, electrical and optical properties of materials. This thesis is divided into two main sections, each describing the work done on a different metal-oxide semiconductor. 1) MOVPE-grown Ga2O3 thin films for UV solar-blind photodetectors and high power devices The semiconducting oxides, among them Ga2O3, have been employed for several decades as transparent conducting oxide (TCO) electrodes for fabrication of solar cells, displays, electronic, and opto-electronic devices. The interest was mainly confined to such applications, as these materials tend to grow intrinsically n-type, and attempts to get an effective p-type doping has consistently failed. The key requirements of TCO electrodes are indeed high electrical conductivity and good transparency, while crystallographic perfection is a minor issue. Furthermore, for a long period no high-quality substrates and epi-layers were available, which in turn impeded the development of a truly full-oxide electronics. Recently, Ga2O3 has attracted renewed interest, as large single crystals and high-quality homo- and hetero-epitaxial layers became available, which paved the way to novel application areas. Our research group spent the last two years in developing a low temperature (500-700°C) MOVPE growth procedure to obtain thin films of Ga2O3 on different substrates (Dept. of Physics and IMEM-CNR at UNIPR). We obtained a significant result growing on oriented sapphire epitaxial films of high crystalline, undoped, pure phase -Ga2O3 (hexagonal). The crystallographic properties of this phase were investigated by XRD, in order to clarify the lattice parameters of the hexagonal cell. First design and development of solar blind UV photodetectors based on -phase was carried out and the optoelectronic performance is evaluated by means of photocurrent spectroscopy. The UV-response is adequately fast and reliable to render this unusual phase a subject of great interest for future applications. The availability of a hexagonal phase of Ga2O3 stable up to 700°C, belonging to the same space group of gallium nitride, with high crystallinity and tunable electrical properties, is intriguing in view of the development of nitride-based devices, by taking advantage of the more favorable symmetry and epitaxial relationships with respect to the monoclinic β-phase. In addition, annealing at temperatures higher than 700°C demonstrate that the hexagonal phase converts totally in the monoclinic one. 2) ZnO nano-tetrapods: charge transport mechanisms and time-response in optoelectronic devices and sensors Size and morphology of ZnO at the nanometer scale play a key role in tailoring its physical and chemical properties. Thanks to the possibility of growing zinc oxide in a variety of different nanostructures, there is a great variety of applications, among which gas sensors, light emitting diodes, transparent conducting oxides, solar cells. Even if the operation of ZnO nanostructure-based devices has been recently demonstrated, the mechanisms of charge transport in these assembly is still under debate. The candidate performed an accurate investigation by photocurrent spectroscopy and DC-photocurrent time evolution of electrical response of both single-tetrapod and tetrapod-assembly devices. During the research done for this thesis, a thermal activation energy enables the performance of samples at high temperatures (above about 300°C). The energy barrier is related to the leg-to-leg interconnection in the assembly of nanotetrapods. Percolation mechanisms are responsible for both the very slow photo-response (minutes to hours or days) and the significant persistent photocurrent. Below the bandgap energy, electronic states were investigated but their contribution to the photocurrent are two-three order of magnitude lower than the band edge. Such devices are suitable for employ in photodetectors as well as in gas sensors, provided that the mechanism by which the photo-current is generated and gas adsorption on the surface modify the conductivity of the material are known.

Estudo da microestrutura e dinâmica molecular do Poly(3-(2\'-ethylhexyl)thiophene)(P3EHT) via ressonância magnética nuclear

O estudo da microestrutura e dinâmica molecular de polímeros conjugados é de grande importância para o entendimento das propriedades físicas desta classe de materiais. No presente trabalho utilizou-se técnicas de ressonância magnética nuclear em baixo e alto campo para elucidar os processos de dinâmica molecular e cristalização do polímero Poly(3-(2’-ethylhexyl)thiophene) - P3EHT. O P3EHT é um polímero modelo para tal estudo, pois apresenta temperatura de fusão bem inferior a sua temperatura de degradação. Esta característica permite acompanhar os processos de cristalização in situ utilizando RMN. Além disso, sua similaridade ao já popular P3HT o torna um importante candidato a camada ativa em dispositivos eletrônicos orgânicos. O completo assinalamento do espectro de 13C para o P3EHT foi realizado utilizando as técnicas de defasamento dipolar e HETCOR. Os processos de dinâmica molecular, por sua vez, foram sondados utilizando DIPSHIFT. Observou-se um gradiente de mobilidade na cadeia lateral do polímero. Além disso, os baixos valores de parametros de ordem obtidos em comparação a experimentos similares realizados no P3HT na literatura indicam um aparente aumento no volume livre entre cadeias consecutivas na fase cristalina. Isso indica que a presença do grupo etil adicional no P3EHT causa um completo rearranjo das moléculas e dificulta seu empacotamento. Constatou-se ainda pouca variação das curvas de DIPSHIFT para os carbonos da cadeia lateral como função do método de excitação utilizado, o que aponta para um polímero que apresenta cadeia lateral móvel mesmo em sua fase cristalina. Os dados de dinâmica molecular foram corroborados por medidas de T1, T1ρ e TCH. Utilizando filtros dipolares em baixo campo observou-se três temperaturas de transição para o P3EHT: 250 K, 325 K e 350 K. A cristalização desse material é um processo lento. Verificou-se que o mesmo pode se estender por até até 24h a temperatura ambiente. Mudanças no espectro de 13C utilizando CPMAS em alto campo indicam um ordenamento dos anéis tiofeno (empacotamento π – π) como o principal processo de cristalização para o P3EHT.

Azimuthal asymmetry in the risetime of the surface detector signals of the Pierre Auger Observatory.

The azimuthal asymmetry in the risetime of signals in Auger surface detector stations is a source of information on shower development. The azimuthal asymmetry is due to a combination of the longitudinal evolution of the shower and geometrical effects related to the angles of incidence of the particles into the detectors. The magnitude of the effect depends upon the zenith angle and state of development of the shower and thus provides a novel observable, (sec theta)(max), sensitive to the mass composition of cosmic rays above 3 x 10(18) eV. By comparing measurements with predictions from shower simulations, we find for both of our adopted models of hadronic physics (QGSJETII-04 and EPOS-LHC) an indication that the mean cosmic-ray mass increases slowly with energy, as has been inferred from other studies. However, the mass estimates are dependent on the shower model and on the range of distance from the shower core selected. Thus the method has uncovered further deficiencies in our understanding of shower modeling that must be resolved before the mass composition can be inferred from (sec theta)(max).

Signal Processing Techniques for Chipless UWB RFID Thermal Threshold Detector Detection.

This letter presents signal processing techniques to detect a passive thermal threshold detector based on a chipless time-domain ultrawideband (UWB) radio frequency identification (RFID) tag. The tag is composed by a UWB antenna connected to a transmission line, in turn loaded with a biomorphic thermal switch. The working principle consists of detecting the impedance change of the thermal switch. This change occurs when the temperature exceeds a threshold. A UWB radar is used as the reader. The difference between the actual time sample and a reference signal obtained from the averaging of previous samples is used to determine the switch transition and to mitigate the interferences derived from clutter reflections. A gain compensation function is applied to equalize the attenuation due to propagation loss. An improved method based on the continuous wavelet transform with Morlet wavelet is used to overcome detection problems associated to a low signal-to-noise ratio at the receiver. The average delay profile is used to detect the tag delay. Experimental measurements up to 5 m are obtained.