Design methodologies of microwawe integrated circuits for satellite telecommunications

The running innovation processes of the microwave transistor technologies, used in the implementation of microwave circuits, have to be supported by the study and development of proper design methodologies which, depending on the applications, will fully exploit the technology potentialities. After the choice of the technology to be used in the particular application, the circuit designer has few degrees of freedom when carrying out his design; in the most cases, due to the technological constrains, all the foundries develop and provide customized processes optimized for a specific performance such as power, low-noise, linearity, broadband etc. For these reasons circuit design is always a “compromise”, an investigation for the best solution to reach a trade off between the desired performances. This approach becomes crucial in the design of microwave systems to be used in satellite applications; the tight space constraints impose to reach the best performances under proper electrical and thermal de-rated conditions, respect to the maximum ratings provided by the used technology, in order to ensure adequate levels of reliability. In particular this work is about one of the most critical components in the front-end of a satellite antenna, the High Power Amplifier (HPA). The HPA is the main power dissipation source and so the element which mostly engrave on space, weight and cost of telecommunication apparatus; it is clear from the above reasons that design strategies addressing optimization of power density, efficiency and reliability are of major concern. Many transactions and publications demonstrate different methods for the design of power amplifiers, highlighting the availability to obtain very good levels of output power, efficiency and gain. Starting from existing knowledge, the target of the research activities summarized in this dissertation was to develop a design methodology capable optimize power amplifier performances complying all the constraints imposed by the space applications, tacking into account the thermal behaviour in the same manner of the power and the efficiency. After a reminder of the existing theories about the power amplifier design, in the first section of this work, the effectiveness of the methodology based on the accurate control of the dynamic Load Line and her shaping will be described, explaining all steps in the design of two different kinds of high power amplifiers. Considering the trade-off between the main performances and reliability issues as the target of the design activity, we will demonstrate that the expected results could be obtained working on the characteristics of the Load Line at the intrinsic terminals of the selected active device. The methodology proposed in this first part is based on the assumption that designer has the availability of an accurate electrical model of the device; the variety of publications about this argument demonstrates that it is so difficult to carry out a CAD model capable to taking into account all the non-ideal phenomena which occur when the amplifier operates at such high frequency and power levels. For that, especially for the emerging technology of Gallium Nitride (GaN), in the second section a new approach for power amplifier design will be described, basing on the experimental characterization of the intrinsic Load Line by means of a low frequency high power measurements bench. Thanks to the possibility to develop my Ph.D. in an academic spin-off, MEC – Microwave Electronics for Communications, the results of this activity has been applied to important research programs requested by space agencies, with the aim support the technological transfer from universities to industrial world and to promote a science-based entrepreneurship. For these reasons the proposed design methodology will be explained basing on many experimental results.

Use of solvents and environmental friendly materials for applications in Green Chemistry

The present Thesis studies three alternative solvent groups as sustainable replacement of traditional organic solvents. Some aspects of fluorinated solvents, supercritical fluids and ionic liquids, have been analysed with a critical approach and their effective “greenness” has been evaluated from the points of view of the synthesis, the properties and the applications. In particular, the attention has been put on the environmental and human health issues, evaluating the eco-toxicity, the toxicity and the persistence, to underline that applicability and sustainability are subjects with equal importance. The “green” features of fluorous solvents and supercritical fluids are almost well-established; in particular supercritical carbon dioxide (scCO2) is probably the “greenest” solvent among the alternative solvent systems developed in the last years, enabling to combine numerous advantages both from the point of view of industrial/technological applications and eco-compatibility. In the Thesis the analysis of these two classes of alternative solvents has been mainly focused on their applicability, rather than the evaluation of their environmental impact. Specifically they have been evaluated as alternative media for non-aqueous biocatalysis. For this purpose, the hydrophobic ion pairing (HIP), which allows solubilising enzymes in apolar solvents by an ion pairing between the protein and a surfactant, has been investigated as effective enzymatic derivatisation technique to improve the catalytic activity under homogeneous conditions in non conventional media. The results showed that the complex enzyme-surfactant was much more active both in fluorous solvents and in supercritical carbon dioxide than the native form of the enzyme. Ionic liquids, especially imidazolium salts, have been proposed some years ago as “fully green” alternative solvents; however this epithet does not take into account several “brown” aspects such as their synthesis from petro-chemical starting materials, their considerable eco-toxicity, toxicity and resistance to biodegradation, and the difficulty of clearly outline applications in which ionic liquids are really more advantageous than traditional solvents. For all of these reasons in this Thesis a critical analysis of ionic liquids has been focused on three main topics: i) alternative synthesis by introducing structural moieties which could reduce the toxicity of the most known liquid salts, and by using starting materials from renewable resources; ii) on the evaluation of their environmental impact through eco-toxicological tests (Daphnia magna and Vibrio fischeri acute toxicity tests, and algal growth inhibition), toxicity tests (MTT test, AChE inhibition and LDH release tests) and fate and rate of aerobic biodegradation in soil and water; iii) and on the demonstration of their effectiveness as reaction media in organo-catalysis and as extractive solvents in the recovery of vegetable oil from terrestrial and aquatic biomass. The results about eco-toxicity tests with Daphnia magna, Vibrio fischeri and algae, and toxicity assay using cultured cell lines, clearly indicate that the difference in toxicity between alkyl and oxygenated cations relies in differences of polarity, according to the general trend of decreasing toxicity by decreasing the lipophilicity. Independently by the biological approach in fact, all the results are in agreement, showing a lower toxicity for compounds with oxygenated lateral chains than for those having purely alkyl lateral chains. These findings indicate that an appropriate choice of cation and anion structures is important not only to design the IL with improved and suitable chemico-physical properties but also to obtain safer and eco-friendly ILs. Moreover there is a clear indication that the composition of the abiotic environment has to be taken into account when the toxicity of ILs in various biological test systems is analysed, because, for example, the data reported in the Thesis indicate a significant influence of salinity variations on algal toxicity. Aerobic biodegradation of four imidazolium ionic liquids, two alkylated and two oxygenated, in soil was evaluated for the first time. Alkyl ionic liquids were shown to be biodegradable over the 6 months test period, and in contrast no significant mineralisation was observed with oxygenated derivatives. A different result was observed in the aerobic biodegradation of alkylated and oxygenated pyridinium ionic liquids in water because all the ionic liquids were almost completely degraded after 10 days, independently by the number of oxygen in the lateral chain of the cation. The synthesis of new ionic liquids by using renewable feedstock as starting materials, has been developed through the synthesis of furan-based ion pairs from furfural. The new ammonium salts were synthesised in very good yields, good purity of the products and wide versatility, combining low melting points with high decomposition temperatures and reduced viscosities. Regarding the possible applications as surfactants and biocides, furan-based salts could be a valuable alternative to benzyltributylammonium salts and benzalkonium chloride that are produced from non-renewable resources. A new procedure for the allylation of ketones and aldehydes with tetraallyltin in ionic liquids was developed. The reaction afforded high yields both in sulfonate-containing ILs and in ILs without sulfonate upon addition of a small amount of sulfonic acid. The checked reaction resulted in peculiar chemoselectivity favouring aliphatic substrates towards aromatic ketones and good stereoselectivity in the allylation of levoglucosenone. Finally ILs-based systems could be easily and successfully recycled, making the described procedure environmentally benign. The potential role of switchable polarity solvents as a green technology for the extraction of vegetable oil from terrestrial and aquatic biomass has been investigated. The extraction efficiency of terrestrial biomass rich in triacylglycerols, as soy bean flakes and sunflower seeds, was comparable to those of traditional organic solvents, being the yield of vegetable oils recovery very similar. Switchable polarity solvents as been also exploited for the first time in the extraction of hydrocarbons from the microalga Botryococcus braunii, demonstrating the efficiency of the process for the extraction of both dried microalgal biomass and directly of the aqueous growth medium. The switchable polarity solvents exhibited better extraction efficiency than conventional solvents, both with dried and liquid samples. This is an important issue considering that the harvest and the dewatering of algal biomass have a large impact on overall costs and energy balance.

Analysis and developments of uncertainty processors for real time flood forecasting

The hydrologic risk (and the hydro-geologic one, closely related to it) is, and has always been, a very relevant issue, due to the severe consequences that may be provoked by a flooding or by waters in general in terms of human and economic losses. Floods are natural phenomena, often catastrophic, and cannot be avoided, but their damages can be reduced if they are predicted sufficiently in advance. For this reason, the flood forecasting plays an essential role in the hydro-geological and hydrological risk prevention. Thanks to the development of sophisticated meteorological, hydrologic and hydraulic models, in recent decades the flood forecasting has made a significant progress, nonetheless, models are imperfect, which means that we are still left with a residual uncertainty on what will actually happen. In this thesis, this type of uncertainty is what will be discussed and analyzed. In operational problems, it is possible to affirm that the ultimate aim of forecasting systems is not to reproduce the river behavior, but this is only a means through which reducing the uncertainty associated to what will happen as a consequence of a precipitation event. In other words, the main objective is to assess whether or not preventive interventions should be adopted and which operational strategy may represent the best option. The main problem for a decision maker is to interpret model results and translate them into an effective intervention strategy. To make this possible, it is necessary to clearly define what is meant by uncertainty, since in the literature confusion is often made on this issue. Therefore, the first objective of this thesis is to clarify this concept, starting with a key question: should be the choice of the intervention strategy to adopt based on the evaluation of the model prediction based on its ability to represent the reality or on the evaluation of what actually will happen on the basis of the information given by the model forecast? Once the previous idea is made unambiguous, the other main concern of this work is to develope a tool that can provide an effective decision support, making possible doing objective and realistic risk evaluations. In particular, such tool should be able to provide an uncertainty assessment as accurate as possible. This means primarily three things: it must be able to correctly combine all the available deterministic forecasts, it must assess the probability distribution of the predicted quantity and it must quantify the flooding probability. Furthermore, given that the time to implement prevention strategies is often limited, the flooding probability will have to be linked to the time of occurrence. For this reason, it is necessary to quantify the flooding probability within a horizon time related to that required to implement the intervention strategy and it is also necessary to assess the probability of the flooding time.

Synthesis and application of new ion-tagged ligands and organocatalysts

We report the synthesis and application of some ion-tagged catalysts in organometallic catalysis and organocatalysis. With the installation of an ionic group on the backbone of a known catalyst, two main effects are generally obtained. i) a modification of the solubility of the catalyst: if judicious choice of the ion pair is made, the ion-tag can confer to the catalyst a solubility profile suitable for catalyst recycling. ii) the ionic group can play a non-innocent role in the process considered: if stabilizing interaction between the ionic group and the developing charges in the transition state are established, the reaction can speed up. We describe the use of ion-tagged diphenylprolinol as Zn ligand. The chiral ligand grafted onto an ionic liquid (IL) was recycled 10 times with no loss of reactivity and selectivity, when it was employed in the first example of enantioselective addition of ZnEt2 to aldehydes in ILs. An ammonium-tagged phosphine displayed the capability to stabilize Pd catalysts for the Suzuki reaction in ILs. The ionic phase was recycled 6 times with no detectable loss of activity and very low Pd leaching in the organic phase. This catalytic system was also employed for the functionalization of the challenging substrate 5,11-dibromotetracene. In the field of organocatalysis, we prepared two ion-tagged derivatives of the McMillan imidazolidinone. The results of the asymmetric Diels-Alder reaction between trans-cinnamaldehyde and cyclopentadiene exhibited great dependence on the position and nature of the ionic group. Finally, when O-TMS-diphenylprolinol was tagged with an imidazolium ion, exploiting a silyl ether linker, an efficient catalyst for the asymmetric addition of aldehydes to nitroolefins was achieved. The catalyst displayed enhanced reactivity and the same high level of selectivity of the untagged parent catalyst and it could be employed in a wide range of reaction conditions, included use of water as solvent.

Design, synthesis and photochemical studies of stilbenoid dendrimers

Stilbenoid dendrimers with stilbene in the periphery and stilbene in periphery as well as core were synthesized by convergent approach except 2nd generation dendrimer with stilbene in the periphery as well as in core (D-5). All dendrimers were characterized by standard techniques such as 1H NMR, 13C NMR, MS and IR spectroscopy. The MALDI-TOF technique proved to be very helpful in the identification of the 2nd generation dendrimer (D-5) with a mass of 3231 a.m.u. The dendrimers were designed in such a way that an intramolecular photochemical CC bond formation was favored. As two stilbene units of the same molecule were close enough so they preferred an intramolecular cyclic process except for zero generation dendrimers. Apart from the cycloaddition, some E/Z isomerization and oligomer formation was also observed on irradiation. These processes were observed by 1H NMR and MALDI-TOF MS. The photochemical behavior was also studied by UV absorption spectroscopy. Irradiating by monochromatic light led to an initial E/Z isomerization and by prolonged irradiation, an irreversible cyclic structure was formed. The choice of the wavelength of incident light is very important as irradiation at 320 nm leads to a reversible E/Z isomerization and a non-reversible cyclobutane formation, but irradiation at 340 nm favors the one-way process E Z. The [2+2] cycloaddition of molecule Tm2De was also studied by irradiating thin films on a quartz surface. An AFM image was taken before irradiation, after 3 sec irradiation and after long irradiation (1 hour). AFM studies show that a short irradiation leads to a cyclic structure as formation of hills of about 20-30 nm on the surface. A prolonged irradiation leads to a CC cross linking which can be monitored on AFM images as disappearance of hills. The roughness goes back to an almost smooth surface. These results prove a very complex material transport, which accompanies the reaction in the surface region.

Electrothermal characterization and nonlinear modelling of GaN transistors for telecommunication circuit design

This thesis starts showing the main characteristics and application fields of the AlGaN/GaN HEMT technology, focusing on reliability aspects essentially due to the presence of low frequency dispersive phenomena which limit in several ways the microwave performance of this kind of devices. Based on an equivalent voltage approach, a new low frequency device model is presented where the dynamic nonlinearity of the trapping effect is taken into account for the first time allowing considerable improvements in the prediction of very important quantities for the design of power amplifier such as power added efficiency, dissipated power and internal device temperature. An innovative and low-cost measurement setup for the characterization of the device under low-frequency large-amplitude sinusoidal excitation is also presented. This setup allows the identification of the new low frequency model through suitable procedures explained in detail. In this thesis a new non-invasive empirical method for compact electrothermal modeling and thermal resistance extraction is also described. The new contribution of the proposed approach concerns the non linear dependence of the channel temperature on the dissipated power. This is very important for GaN devices since they are capable of operating at relatively high temperatures with high power densities and the dependence of the thermal resistance on the temperature is quite relevant. Finally a novel method for the device thermal simulation is investigated: based on the analytical solution of the tree-dimensional heat equation, a Visual Basic program has been developed to estimate, in real time, the temperature distribution on the hottest surface of planar multilayer structures. The developed solver is particularly useful for peak temperature estimation at the design stage when critical decisions about circuit design and packaging have to be made. It facilitates the layout optimization and reliability improvement, allowing the correct choice of the device geometry and configuration to achieve the best possible thermal performance.

New catalytic processes for the synthesis of adipic acid

The aim of my Ph.D. research was to study the new synthetic ways for the production of adipic acid. Three different pathways were studied: i) oxidation of cyclohexanone with molecular oxygen using Keggin – heteropolycompounds as the catalyst, ii) Baeyer – Villiger oxidation of cyclohexanone with hydrogen peroxide in the presence of two different heterogeneous catalysts, titanium silicalite and silica grafted decatungstate, iii) two step synthesis of adipic acid starting from cyclohexene via 1,2-cyclohexanediol. The first step was catalyzed by H2WO4 in the presence of the phase transfer catalyst, the oxidant was hydrogen peroxide. The second step, oxidation of 1,2 – cyclohexanediol was performed in the presence of oxygen and the heterogeneous catalyst – ruthenium on alumina. The results of my research showed that: i) Oxidation of cyclohexanone with molecular oxygen using Keggin heteropolycompounds is possible, anyway the conversion of ketone is low and the selectivity to adipic acid is lowered by the consecutive reaction to from lower diacids. Moreover it was found out, that there are two mechanisms involved: redox type and radicalic chain-reaction autoxidation. The presence of the different mechanism is influenced by the reaction condition. ii) It is possible to perform thermally activated oxidation of cyclohexanone and obtain non negligible amount of the products (caprolactone and adipic acid). Performing the catalyzed reaction it was demonstrated that the choice of the reaction condition and of the catalyst plays a crucial role in the product selectivity, explaining the discrepancies between the literature and our research. iii) Interesting results can be obtained performing the two step oxidation of cyclohexene via 1,2-cyclohexanediol. In the presence of phase transfer catalyst it is possible to obtain high selectivity to alcohol with stoichiometric amount of oxidant. In the second step of the synthesis, the conversion of alcohol is rather low with modest selectivity to adipic acid

A study of nitronyl and imino nitroxide radicals attached to heterocyclic cores

Stabile organische Radikale mit zusätzlichen Funktionalitäten wie Donor/Akzepotor Eigenschaften und Ligandeneignung für Übergangsmetallkomplexierung repräsentieren eine synthetische Herausforderung beim Streben nach der Konstruktion hochdimensionaler heterospin Strukturen. In diesem Hinblick wurden acht neue Hochspinbiradikal-Moleküle zusammen mit ihren Monoradikal- Pendants in dieser Arbeit hergestellt. Die Wahl der Liganden als organische Distanzhalter der Radikaleinheiten wurde auf stickstoffhaltige Heterozyklen (Pyridin und Pyrazol) gelenkt. Diese wurden weiterhin mit den stabilen Spinträgern Nitronylnitroxid- (NN) und Iminonitroxidfragmenten (IN) dekoriert. Ihre Synthese beinhaltete mehrstufige Umsetzungen (Brominierung, Iodierung, N- und Carbaldehyd Schutzgruppen, Stille-Kupplung, Grignard Reaktion, etc.) um die Mono- und Dicarbaldehyd-heterocyclenderivate als Schlüsselvorläufer der Radikaleinheiten zu gewinnen. Die Carbaldehyd-Zwischenstufen wurden Kondensationsreaktionen mit 2,3-Dimethyl-2,3-bis(hydroxylamino)-butan unterworfen (üblicherweise in Dioxan unter Argon für ~ 7 Tage), gefolgt von der Oxidation der Bis-hydroxylimidazolidin-Vorläufer unter Phasentransferkatalyse (NaIO4/H2O). Die Radikalmoleküle wurden mit verschiedenen spektroskopischen Methoden untersucht (FT/IR, UV/Vis/ EPR etc.) und ihre Einkristalle mit Röntgenstrahlbeugung gemessen. Die UV/VIS- Lösungsspektren zeigten in einem breiten Bereich verschiedener Lösungsmittelpolaritäten keine spezifische Wechselwirkung zwischen Lösungsmittel und Radikaleinheit, während ihre Stabilitäten in protischen Lösunsgmitteln wie MeOH stark abnahmen. Als Pulver konnten sie jedoch im Kühlschrank an der Luft für eine Jahr gelagert werden, ohne sich zu zersetzen. Die spektroskopischen Fingerabdrücke der Radikale wurden eindeutig identifiziert and erschienen stark abhängig vom Typ des pi-Ringsystems an das die Spinträger gekoppelt wurden. Basierend auf diesen Informationen wurde ein schnelles Protokoll etabliert, das eine direkte Zuordnung der Art der Radikale und ihrer Anzahl ermöglicht, sowie ihre Reinheit und Verunreinigungen zu definieren. In Lösung bestätigte die Analyse der EPR Spektren der Biradikale die starke Austauschwechselwirkung J zwischen den Radikalfragmenten über die Kopplungseinheiten (J >> an, an ist die Stickstoffhyperfeinkopplungskonstante). Dies wurde weiter unterstützt durch die Beobachtungen in gefrorener Lösung über die Nullfeldaufspaltungen und verbotenen Halbfeldübergänge (Δms = 2). Die Temperaturabhängigkeiten der Δms = 2 - EPR Signale wurden bis herunter auf 4 K gemessen und das exakte Vorzeichen und die Größe von J ermittelt. Diese Arbeit unterstreicht die Möglichkeit über synthetische Chemie eine Feineinstellung der „through bond“ Austauschwechselwirkung zwischen verwandten pi- und sigma- konjugierten Heterozyklen zu erreichen, in denen der S = 1 Grundzustand angenommen wird. Zusätzlich zeigten diese Resultate, dass die Übertragung der Spinpolarisation durch verschiedene Koppler sehr effektiv war.

Reconstruction of Etna recent flank eruptions for assessing diversion barrier project

The thesis contributed to the volcanic hazard assessment through the reconstruction of some historical flank eruptions of Etna in order to obtain quantitative data (volumes, effusion rates, etc.) for characterizing the recent effusive activity, quantifying the impact on the territory and defining mitigation actions for reducing the volcanic risk as for example containment barriers. The reconstruction was based on a quantitative approach using data extracted from aerial photographs and topographic maps. The approach allows to obtain the temporal evolution of the lava flow field and estimating the Time Average Discharge Rate (TADR) by dividing the volume emplaced over a given time interval for the corresponding duration. The analysis concerned the 2001, 1981 and 1928 Etna eruptions. The choice of these events is linked to their impact on inhabited areas. The results of the analysis showed an extraordinarily high effusion rate for the 1981 and 1928 eruptions (over 600 m^3/s), unusual for Etna eruptions. For the 1981 Etna eruption an eruptive model was proposed to explain the high discharge rate. The obtained TADRs were used as input data for simulations of the propagation of the lava flows for evaluating different scenarios of volcanic hazard and analyse different mitigation actions against lava flow invasion. It was experienced how numerical simulations could be adopted for evaluating the effectiveness of barrier construction and for supporting their optimal design. In particular, the gabions were proposed as an improvement for the construction of barriers with respect to the earthen barriers. The gabion barriers allow to create easily modular structures reducing the handled volumes and the intervention time. For evaluating operational constrain an experimental test was carried out to test the filling of the gabions with volcanic rock and evaluating their deformation during transport and placement.

Geometric and Combinatorial Aspects of NonEquilibrium Statistical Mechanics

Non-Equilibrium Statistical Mechanics is a broad subject. Grossly speaking, it deals with systems which have not yet relaxed to an equilibrium state, or else with systems which are in a steady non-equilibrium state, or with more general situations. They are characterized by external forcing and internal fluxes, resulting in a net production of entropy which quantifies dissipation and the extent by which, by the Second Law of Thermodynamics, time-reversal invariance is broken. In this thesis we discuss some of the mathematical structures involved with generic discrete-state-space non-equilibrium systems, that we depict with networks in all analogous to electrical networks. We define suitable observables and derive their linear regime relationships, we discuss a duality between external and internal observables that reverses the role of the system and of the environment, we show that network observables serve as constraints for a derivation of the minimum entropy production principle. We dwell on deep combinatorial aspects regarding linear response determinants, which are related to spanning tree polynomials in graph theory, and we give a geometrical interpretation of observables in terms of Wilson loops of a connection and gauge degrees of freedom. We specialize the formalism to continuous-time Markov chains, we give a physical interpretation for observables in terms of locally detailed balanced rates, we prove many variants of the fluctuation theorem, and show that a well-known expression for the entropy production due to Schnakenberg descends from considerations of gauge invariance, where the gauge symmetry is related to the freedom in the choice of a prior probability distribution. As an additional topic of geometrical flavor related to continuous-time Markov chains, we discuss the Fisher-Rao geometry of nonequilibrium decay modes, showing that the Fisher matrix contains information about many aspects of non-equilibrium behavior, including non-equilibrium phase transitions and superposition of modes. We establish a sort of statistical equivalence principle and discuss the behavior of the Fisher matrix under time-reversal. To conclude, we propose that geometry and combinatorics might greatly increase our understanding of nonequilibrium phenomena.

Innovation and economic performance of the firms in the service sector: relevant issues and open problems

This thesis is a collection of essays related to the topic of innovation in the service sector. The choice of this structure is functional to the purpose of single out some of the relevant issues and try to tackle them, revising first the state of the literature and then proposing a way forward. Three relevant issues has been therefore selected: (i) the definition of innovation in the service sector and the connected question of measurement of innovation; (ii) the issue of productivity in services; (iii) the classification of innovative firms in the service sector. Facing the first issue, chapter II shows how the initial width of the original Schumpeterian definition of innovation has been narrowed and then passed to the service sector form the manufacturing one in a reduce technological form. Chapter III tackle the issue of productivity in services, discussing the difficulties for measuring productivity in a context where the output is often immaterial. We reconstruct the dispute on the Baumol’s cost disease argument and propose two different ways to go forward in the research on productivity in services: redefining the output along the line of a characteristic approach; and redefining the inputs, particularly analysing which kind of input it’s worth saving. Chapter IV derives an integrated taxonomy of innovative service and manufacturing firms, using data coming from the 2008 CIS survey for Italy. This taxonomy is based on the enlarged definition of “innovative firm” deriving from the Schumpeterian definition of innovation and classify firms using a cluster analysis techniques. The result is the emergence of a four cluster solution, where firms are differentiated by the breadth of the innovation activities in which they are involved. Chapter 5 reports some of the main conclusions of each singular previous chapter and the points worth of further research in the future.

'A Distortion in the mirror of being': verso un modello liquido di personaggio. Da Nabokov alle sperimentazioni contemporanee in ambito slavo

La tesi mira a ridefinire lo statuto del personaggio nell’ambito del self-conscious novel postmoderno, alla luce delle più recenti tendenze narratologiche, con particolare riferimento all’unnatural narratology. Per poter presentare un modello scientificamente valido si è fatto ricorso alla comparazione della produzione letteraria di due macro-aree: quella britannica e quella slava (Russia - Unione Sovietica - e Polonia). Come figura di mediazione tra queste due culture si pone senza dubbio Vladimir V. Nabokov, cardine e personalità di spicco della ricerca. Tra le analisi testuali proposte sono stati presi in considerazione i seguenti autori: Julian Barnes, Vladimir Nabokov, Daniil Charms, Konstantin Vaginov, Andrej Bitov, Saša Sokolov, Bruno Schulz e Tadeusz Kantor.

The gaseous halo of the Milky Way

In the last decade, sensitive observations have revealed that disc galaxies are surrounded by multiphase gaseous halos produced by the circulation of gas from the discs to the environment and vice-versa. This Thesis is a study of the gaseous halo of the Milky Way carried out via the modelling of the HI emission and the available absorption-line data. We fitted simple kinematical models to the HI LAB Survey and found that the Galaxy has a massive (~3x10^8 Mo) HI halo extending a few kiloparsecs above the plane. This layer rotates more slowly than the disc and shows a global inflow motion, a kinematics similar to that observed in the HI halos of nearby galaxies. We built a dynamical model of the galactic fountain to reproduce the properties of this layer. In this model, fountain clouds are ejected from the disc by SN feedback and - as suggested by hydrodynamical simulations - triggers the cooling of coronal gas, which is entrained by the cloud wakes and accretes onto the disc when the clouds fall back. For a proper choice of the parameters, the model reproduces well the HI data and predicts an accretion of coronal gas onto the disc at a rate of 2 Mo/yr. We extended this model to the warm-hot component of the halo, showing that most of the ion absorption features observed towards background sources are consistent with being produced in the turbulent wakes that lag behind the fountain clouds. Specifically, the column densities, positions, and velocities of the absorbers are well reproduced by our model. Finally, we studied the gas content of galaxies extracted from a cosmological N-body+SPH simulation, and found that an HI halo with the forementioned properties is not observed, probably due ti the relatively low resolution of the simulations.

Subject-specific musculoskeletal models of the lower limbs for the prediction of skeletal loads during motion

The determination of skeletal loading conditions in vivo and their relationship to the health of bone tissues, remain an open question. Computational modeling of the musculoskeletal system is the only practicable method providing a valuable approach to muscle and joint loading analyses, although crucial shortcomings limit the translation process of computational methods into the orthopedic and neurological practice. A growing attention focused on subject-specific modeling, particularly when pathological musculoskeletal conditions need to be studied. Nevertheless, subject-specific data cannot be always collected in the research and clinical practice, and there is a lack of efficient methods and frameworks for building models and incorporating them in simulations of motion. The overall aim of the present PhD thesis was to introduce improvements to the state-of-the-art musculoskeletal modeling for the prediction of physiological muscle and joint loads during motion. A threefold goal was articulated as follows: (i) develop state-of-the art subject-specific models and analyze skeletal load predictions; (ii) analyze the sensitivity of model predictions to relevant musculotendon model parameters and kinematic uncertainties; (iii) design an efficient software framework simplifying the effort-intensive phases of subject-specific modeling pre-processing. The first goal underlined the relevance of subject-specific musculoskeletal modeling to determine physiological skeletal loads during gait, corroborating the choice of full subject-specific modeling for the analyses of pathological conditions. The second goal characterized the sensitivity of skeletal load predictions to major musculotendon parameters and kinematic uncertainties, and robust probabilistic methods were applied for methodological and clinical purposes. The last goal created an efficient software framework for subject-specific modeling and simulation, which is practical, user friendly and effort effective. Future research development aims at the implementation of more accurate models describing lower-limb joint mechanics and musculotendon paths, and the assessment of an overall scenario of the crucial model parameters affecting the skeletal load predictions through probabilistic modeling.

Bestimmung der fehlenden transversalen Energie auf der ersten Triggerstufe beim ATLAS-Experiment und Optimierung der Triggerselektion von supersymmetrischen Ereignissen

Das Standardmodell der Teilchenphysik, das drei der vier fundamentalen Wechselwirkungen beschreibt, stimmt bisher sehr gut mit den Messergebnissen der Experimente am CERN, dem Fermilab und anderen Forschungseinrichtungen überein. rnAllerdings können im Rahmen dieses Modells nicht alle Fragen der Teilchenphysik beantwortet werden. So lässt sich z.B. die vierte fundamentale Kraft, die Gravitation, nicht in das Standardmodell einbauen.rnDarüber hinaus hat das Standardmodell auch keinen Kandidaten für dunkle Materie, die nach kosmologischen Messungen etwa 25 % unseres Universum ausmacht.rnAls eine der vielversprechendsten Lösungen für diese offenen Fragen wird die Supersymmetrie angesehen, die eine Symmetrie zwischen Fermionen und Bosonen einführt. rnAus diesem Modell ergeben sich sogenannte supersymmetrische Teilchen, denen jeweils ein Standardmodell-Teilchen als Partner zugeordnet sind.rnEin mögliches Modell dieser Symmetrie ist das R-Paritätserhaltende mSUGRA-Modell, falls Supersymmetrie in der Natur realisiert ist.rnIn diesem Modell ist das leichteste supersymmetrische Teilchen (LSP) neutral und schwach wechselwirkend, sodass es nicht direkt im Detektor nachgewiesen werden kann, sondern indirekt über die vom LSP fortgetragene Energie, die fehlende transversale Energie (etmiss), nachgewiesen werden muss.rnrnDas ATLAS-Experiment wird 2010 mit Hilfe des pp-Beschleunigers LHC mit einer Schwerpunktenergie von sqrt(s)=7-10 TeV mit einer Luminosität von 10^32 #/(cm^2*s) mit der Suche nach neuer Physik starten.rnDurch die sehr hohe Datenrate, resultierend aus den etwa 10^8 Auslesekanälen des ATLAS-Detektors bei einer Bunchcrossingrate von 40 MHz, wird ein Triggersystem benötigt, um die zu speichernde Datenmenge zu reduzieren.rnDabei muss ein Kompromiss zwischen der verfügbaren Triggerrate und einer sehr hohen Triggereffizienz für die interessanten Ereignisse geschlossen werden, da etwa nur jedes 10^8-te Ereignisse für die Suche nach neuer Physik interessant ist.rnZur Erfüllung der Anforderungen an das Triggersystem wird im Experiment ein dreistufiges System verwendet, bei dem auf der ersten Triggerstufe mit Abstand die höchste Datenreduktion stattfindet.rnrnIm Rahmen dieser Arbeit rn%, die vollständig auf Monte-Carlo-Simulationen basiert, rnist zum einen ein wesentlicher Beitrag zum grundlegenden Verständnis der Eigenschaft der fehlenden transversalen Energie auf der ersten Triggerstufe geleistet worden.rnZum anderen werden Methoden vorgestellt, mit denen es möglich ist, die etmiss-Triggereffizienz für Standardmodellprozesse und mögliche mSUGRA-Szenarien aus Daten zu bestimmen. rnBei der Optimierung der etmiss-Triggerschwellen für die erste Triggerstufe ist die Triggerrate bei einer Luminosität von 10^33 #/(cm^2*s) auf 100 Hz festgelegt worden.rnFür die Triggeroptimierung wurden verschiedene Simulationen benötigt, bei denen eigene Entwicklungsarbeit eingeflossen ist.rnMit Hilfe dieser Simulationen und den entwickelten Optimierungsalgorithmen wird gezeigt, dass trotz der niedrigen Triggerrate das Entdeckungspotential (für eine Signalsignifikanz von mindestens 5 sigma) durch Kombinationen der etmiss-Schwelle mit Lepton bzw. Jet-Triggerschwellen gegenüber dem bestehenden ATLAS-Triggermenü auf der ersten Triggerstufe um bis zu 66 % erhöht wird.