Influência de diferentes métodos de limpeza sobre a eficiência de corte e as características morfológicas de fresas Carbide

Introduction: Currently, there are many questions regarding the cleaning methods seeking greater efficiency and less loss of burs. Aim: the aim of this study was to evaluate the influence of cleaning methods on the cutting efficiency and morphological characteristics of stainless steel burs tungsten carbide (carbide). Materials and method: Thirty burs were divided into five groups (n = 5) according with the cleaning method: L1 - steel brush, L2 - nylon brush, L3 - ultrasound  +  distilled water, L4 - ultrasound + descaling solution and L5 - no cleaning method (control). The burs were used for the cutting of bovine enamel during six periods of 12 minutes each. After each period, the burs were cleaned (except L5 ) following the protocol established for each group. The cutting efficiency was determined by mass loss and morphological characteristics. Result: The average amount of wear after 72 minutes of use were L1  = 0.3558 g; L2  = 0.4275 g; L3  = 0.4652 g; L4  = 0.4396 g e L5  = 0.4854 g; significant differences in the time of use (p  <  0.001) and cleaning method (p  <  0.001). The L1 group showed the worst performance. Regardless of the experimental group, morphological analysis revealed alterations in the cutting blades soon after the first 12 minutes, being L1 the most affected group. Conclusion: The cleaning with wire brush was the most damaging method to the cutting efficiency and to the morphology of carbide burs.

Reproducibility of microhandeness measurements in different surfices

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos da aplicação de resina hidrofóbica sobre a resistência de união de adesivos autocondicionantes de frasco único

Introduction: It is known that self-etching adhesive systems can act as semi-permeable membranes. Objective: Evaluate the effects of additional layer of hydrophobic resin on the microtensile bond strength of self-etching one-bottle adhesives. Material and method: Sixty bovine incisors were used in this study. The facial enamel surfaces of the crowns were abraded with silicon carbide paper to expose flat, mid-coronal dentin surfaces. The following adhesives were used: Clearfil Tri S Bond (CTSB), AdheSE One (ADH) and One Coat  7.0 (OC). Each material was tested with and without applying an additional layer of hydrophobic material from the same manufacturer. Z-350 composite resin was inserted in three 1 mm increments. All adhesive restorative procedure was performed under simulated pulpal pressure and the microtensile test was performed immediately after curing the composite resin. Data were submitted to ANOVA and Tukey test (p < 0.05). Result: For all adhesives tested, the worst results were observed in groups which the additional layer of hydrophobic resin was not applied. Conclusion: The application of additional layer of hydrophobic material can improve the adhesion of self-etching all-in-one adhesive systems.

Microdureza e rugosidade superficial do esmalte submetido ao clareamento: uma revisão de literatura

The increasing importance of aesthetic in the Dentistry for the patients and the consumers brought a constant rise in the number of products and procedures to facilitate the confection of the dental bleaching. Concomitantly, thone was a sudden increase in the number of research and publications, in vitro and in vivo, about its possible adverse reactions. Through literature revision this study aims to verify the possible morphologic alterations of the submitted enamel and dentine with different bleaching agents making critical analysis of the results of the current research with relation to the study of the microhardness and superficial roughness.

Hipersensibilidade dentinária cervical: em busca de um tratamento eficaz

The knowledge of the etiology of any disease or condition is paramount to a safe and effective treatment. This literature review aims to show some options to treat dentine hypersensitivity (HSDC). The loss of cervical enamel and cementum exposure of tubules leads to a painful condition and patient discomfort, called HSDC. This loss of tooth structure occurs due to formation of cervical lesions in cases of gingival recession, abrasion, erosion, or abfraction by the association of two or more factors. Some treatments are not effective, but there are effective therapies, such as: application of ferric oxalate, potassium oxalate, potassium nitrate, fluoride varnish, solutions of calcium phosphate, adhesives and Bonding procedures. Therefore, the identification and removal of etiological factors is essential to successful treatment of HSDC normally associated to tubules obliterate and consequent reduction of fluid motion within the dentin.

Comparative analysis of three rotary instruments used for coronal pre-enlargement in radicular dentin thickness and root canal area of mandibular molars

Purpose: The purpose of this study was to evaluate the increase of the cervical area and dentin thickness in mesial and distal walls of the mesial canals from mandibular molars after the use of LA Axxess (LA), CP Drill (CP) and Gates-Glidden (GG) rotary instruments. Material and Methods: Sixty root canals from thirty mandibular first molar were sectioned 3 mm below the cement-enamel junction, divided in 3 groups (n = 20 root canals, each) according to rotary instrument used, and the cervical images were captured before and after pre-enlargement instrumentation. The increase of the instrumented cervical area (mm2) and the dentin removal thickness (mm), at mesial and distal walls were calculated using Image tools software, by comparison of images. Data were analyzed by ANOVA and Tukey tests (p=0.05). Results: All rotary instruments promoted thickness reduction in dentin walls. In mesial wall, all rotary instruments promoted similar thickness reduction of dentinal wall and did not differ from each other (p>0.05). In distal wall, LA Axxess instrument promoted higher dentin thickness reduction than other groups (p<0.05). The three rotary instruments promoted different increase at the instrumented cervical area (p<0.05), LA promoted the highest increase area and GG and CP presented similar results. Conclusion: LA 20/0.06 promoted the highest thickness reduction in distal wall and increase of cervical area of root canal. On the other hand, CP was the safest instrument, with lower dentin removal of distal wall and similar increased area to GG.

Effect of two formulations of 10% sodium ascorbate on fracture resistance of endodontically treated tooth submitted to dental bleaching with hydrogen peroxide associated titanium dioxide nanoparticles

Purpose: This study evaluated the effect of 10% sodium ascorbate (10SA), in gel (10SAg) or aqueous solution (10SAs) formulations, on fracture resistance of endodontically treated tooth submitted to dental bleaching procedures with 15% hydrogen peroxide associated with titanium dioxide (15HP-TiO2) nanoparticles and photoactivated by LED-laser. Material and methods: Forty maxillary premolars were endodontically-treated and embedded in acrylic resin up to the cement-enamel junction. The specimens were divided into four groups (n=10): G1 (negative control): no bleaching, coronal access restored with composite resin; G2 (positive control): three dental bleaching sessions using 15HP-TiO2 and LED-laser photoactivation and restored with composite resin (positive control); G3 (10SAg): similar procedures to G2, but applied 10SA, in gel formulation, for 24 hours before restoration; G4 (10SAs): similar procedures to G3, but applied 10SA, in aqueous solution formulation. The 15HP-TiO2 was applied on buccal and lingual surfaces of the crown tooth and inside the pulp chamber and photoactivated by LED-laser. Between each bleaching session, the teeth were maintained in artificial saliva, at 37oC, for 7 days. In sequence, the teeth were submitted to fracture resistance testing using an eletromechanical machine test. The data was analyzed using Kruskal Wallis test (p = 0.05) Results: There are no differences significant among the groups in relation to fracture resistance of endodontically treated teeth (p>0.05). Conclusions: The use of 10% sodium ascorbate, in gel or aqueous solution formulations, did not interfered on the fracture resistance teeth after dental bleaching using 15HP-TiO2 and LED-laser photoactivation.

Influence of standard load micro and nanopatterned in surface roughness of bleached teeth and submitted to different surface treatments?

The aim of this study was evaluate the dental enamel after whitening treatment with Opalescence Boost PF® 38%, correlating the structural alterations in the surface of the enamel with its respective pH and verify if whitened teeth submitted to different finishing and polishing techniques show similar surface texture to healthy teeth (control group). Sixty premolars were divided in 6 groups (n = 10), which had been immersed in artificial saliva during all the experiment. Protocol whitening was performed according to the manufacturer recommendations, and then the specimens were submitted to different polishing technique with Sof-Lex Pop On® disks, Flex Diamond® felt disks using two different micrometric polishing pastes (Enamelize® and Diamond Polish®) and two nanometric polishing pastes (Lummina-E Diamond and Lummina-E Alumina), according to the groups. Representative specimens were analyzed in scanning electronic microscopy (SEM). Whitening gel used in this experiment had modified the morphologic aspect of the enamel surface. It was found that two nanometric polishing pastes (G5 and G6) promoted a less rough surface compared to control group even after the whitening process.

Fluorescence Level of Composites Assessed by Computer Processing of Digital Images - ScanWhite

The human dentition is naturally translucent, opalescent and fluorescent. Differences between the level of fluorescence of tooth structure and restorative materials may result in distinct metameric properties and consequently perceptible disparate esthetic behavior, which impairs the esthetic result of the restorations, frustrating both patients and staff. In this study, we evaluated the level of fluorescence of different composites (Durafill in tones A2 (Du), Charisma in tones A2 (Ch), Venus in tone A2 (Ve), Opallis enamel and dentin in tones A2 (OPD and OPE), Point 4 in tones A2 (P4), Z100 in tones A2 ( Z1), Z250 in tones A2 (Z2), Te-Econom in tones A2 (TE), Tetric Ceram in tones A2 (TC), Tetric Ceram N in tones A1, A2, A4 (TN1, TN2, TN4), Four seasons enamel and dentin in tones A2 (and 4SD 4SE), Empress Direct enamel and dentin in tones A2 (EDE and EDD) and Brilliant in tones A2 (Br)). Cylindrical specimens were prepared, coded and photographed in a standardized manner with a Canon EOS digital camera (400 ISO, 2.8 aperture and 1/ 30 speed), in a dark environment under the action of UV light (25 W). The images were analyzed with the software ScanWhite©-DMC/Darwin systems. The results showed statistical differences between the groups (p < 0.05), and between these same groups and the average fluorescence of the dentition of young (18 to 25 years) and adults (40 to 45 years) taken as control. It can be concluded that: Composites Z100, Z250 (3M ESPE) and Point 4 (Kerr) do not match with the fluorescence of human dentition and the fluorescence of the materials was found to be affected by their own tone.

Conservative treatment for amelogenesis imperfecta: a case report

Amelogenesis imperfecta is a hereditary condition that can alter the thickness, color, and shape of tooth enamel. Recent adhesive materials and techniques have provided less invasive treatment options. This case report presents the treatment of a patient whose anterior teeth had color alterations, white spots, pits, and shape defects. Using a more conservative technique, the mandibular and maxillary anterior teeth were restored using veneer direct composite restorations. After 6 years, the restorations demonstrated no deterioration, and no pathology was seen in association with the rehabilitation.

Methods for removal of resin remaining after debonding of orthodontic brackets: a literature review

The removal of resin debris and/or resin cement from the enamel surface without causing iatrogenic is the main objective when removing the orthodontic brackets. Some factors such as the time required for removal, damage to the tooth structure, are essential factors for the clinician at the time of removal. Various techniques are used for the removal of orthodontic brackets after the treatment; it is known that the use of clinical procedures such as the use of diamond burs and some pliers removers can damage the structure of the enamel, often depending on the bond strength that should be taken into consideration at the time of removal. This literature review aims to gather the most relevant studies that can clarify the clinical technique, which may be more suitable for removal of the brackets.

Estudio descriptivo in vitro de dos agentes blanqueadores de distinta concentración sobre la micromorfología del esmalte bovino

Dental tooth bleaching is a conservative option for the treatment of tooth stains. It is based on the use of hydrogen peroxide as an active agent. Despite its effectiveness to lighten tooth colour, there is concern regarding its use due to the effects it could have over enamel surface. There is scarce evidence on the subject and contradictions exist between different authors. The aim of this study was to compare enamel surface micromorphology after bleaching teeth with different concentrations of hydrogen peroxide solutions. Method: 50 healthy bovine incisors sectioned horizontally at the cemento-enamel junction were prepared. Contents of pulp chamber and tooth surfaces were cleaned. The buccal surface of each tooth was divided vertically, assigning one half to the control group (CG) and the other randomly to: Group 1: 25 samples treated with 15% hydrogen peroxide with nitrogen doped titanium dioxide. Group 2: 25 samples treated with 35% hydrogen peroxide. Square samples (2x2 mm.) were obtained and observed by SEM (magnification of 5.000x and 10.000x). Results: All treated groups showed longitudinal depressions on the surface and increased surface roughness. Conclusions: Tooth bleaching with hydrogen peroxide produces subclinical alterations over bovine enamel surface. 15% hydrogen peroxide bleaching agent produced less micromorphology alteration over bovine enamel surface than the 35% hydrogen peroxide agent.

Estado actual del blanqueamiento: sigue siendo un tratamiento seguro? review

The demand for cosmetic dentistry, including teeth whitening, has increased in recent years. The home teeth whitening and in-office, are widely used in dental practice. The mechanism by which it works is by oxidation of the chromogenic existing tooth structure. This is an effective and minimally invasive procedure that achieves tooth lighten the color, however, may cause alterations in the enamel surface, such as a dental permeability increase. Another effect caused by this procedure is tooth sensitivity, being the most common side effect, up to 65% of individuals have had a secondary effect at least once during treatment. This sensitivity and gingival irritation caused by bleaching may vary depending on the patient and used bleaching product

Hidden caries: a critical review

Hidden caries is a type of lesion visualized in dentin, mainly by means of bitewing radiographs, in which, clinically, the occlusal enamel appears healthy or minimally demineralized and radiographically presents progressive demineralization in dentin, which may progress and compromise the pulp-dentin complex. Although the etiology of hidden caries is unknown, many theories have been studied, including structural and anatomical defects of enamel, their specific microbiota and the use of fluoride, which is most accepted theory. Considering the clinical concern, since these lesions have a silent progression and often are not detected on routine clinical examinations, this study aims to conduct a critical discussion of the etiology, prevalence, diagnostic methods and treatment decision for lesions of hidden caries, alerting professionals about the importance of routine use of bitewing radiographs even in patients considered “cariesfree” or low risk of caries, for more effective diagnosis.

Análise dos troncos radiculares, abertura da raízes e projeções cervicais de esmalte de furcas de molares superiores e inferiores: Estudo in vitro

Periodontal treatment of teeth with furcation lesions often have unpredictable results due to several factors that may hinder therapy or influence the progress of periodontal disease. Of these, the length of the root trunk may contribute to the early injury of the furcations or even cause complications for the application of the treatment; the opening of the roots can guide the type of treatment to be instituted and cervical enamel projections may hinder the instrumentation of the region or even act as a retention plate niche. Thus, the purpose of this study was measured using a digital caliper, root logs database 400 molar both the 1st and the 2nd and both upper and lower as well as analyze using appropriate index type projection cervical enamel and through appropriate classification the opening of the roots in order to guide the diagnosis and treatment plan. We conclude that there is variation in measures of root trunk between the faces of the teeth examined and that greater cervical enamel projection (ECP) correlates with a decrease in the length of the root trunk in the sample evaluated as the first molars have higher occurrence of roots with a degree of opening larger than the second molars.