Microcontroller-based interface circuit for inductive sensors

This work proposes a fully-digital interface circuit for the measurement of inductive sensors using a low-cost microcontroller (µC) and without any intermediate active circuit. Apart from the µC and the sensor, the circuit just requires an external resistor and a reference inductance so that two RL circuits with a high-pass filter (HPF) topology are formed. The µC appropriately excites such RL circuits in order to measure the discharging time of the voltage across each inductance (i.e. sensing and reference) and then it uses such discharging times to estimate the sensor inductance. Experimental tests using a commercial µC show a non-linearity error (NLE) lower than 0.5%FSS (Full-Scale Span) when measuring inductances from 1 mH to 10 mH, and from 10 mH to 100 mH.

Quantificação de fluxos de mercúrio gasoso na interface solo/atmosfera utilizando câmara de fluxo dinâmica: aplicação na bacia do Rio Negro

Gaseous mercury sampling conditions were optimized and a dynamic flux chamber was used to measure the air/surface exchange of mercury in some areas of the Negro river basin with different vegetal coverings. At the two forest sites (flooding and non-flooding), low mercury fluxes were observed: maximum of 3 pmol m-2 h-1 - day and minimum of -1 pmol m-2 h-1 - night. At the deforested site, the mercury fluxes were higher and always positive: maximum of 26 pmol m-2 h-1 - day and 17 pmol m-2 h-1 - night. Our results showed that deforestation could be responsible for significantly increasing soil Hg emissions, mainly because of the high soil temperatures reached at deforested sites.

Estimativa do fluxo de amônia na interface ar-mar na Baía de Guanabara: estudo preliminar

In the begining of April 2004, concentrations of NHx (NH3 + NH4+) were measured in surface waters of the Guanabara Bay. Concentrations varied from 2 to 143 mmol L-1. Ammonia exchange at the air-sea interface was quantified using a numerical model. No measurement of NH3 concentration in air (c air) was performed. Thus, calculations of NH3 flux were based on the assumptions of c air = 1 and 5 µg m-3. Fluxes were predominantly from the water to the atmosphere and varied from -20 to almost 3500 µg N m-2 h-1.

Emergency Management and Wildland-Urban Interface Fires in the United States of America

FEMA's mission is to support our citizens and first responders to ensure that as a Nation we work together to build, sustain, and improve our capability to prepare for, protect against, respond to, recover from, and mitigate all hazards.

Brain Computer Interface for Virtual Reality Control

A brain-computer interface (BCI) is a new communication channel between the human brain and a computer. Applications of BCI systems comprise the restoration of movements, communication and environmental control. In this study experiments were made that used the BCI system to control or to navigate in virtual environments (VE) just by thoughts. BCI experiments for navigation in VR were conducted so far with synchronous BCI and asynchronous BCI systems. The synchronous BCI analyzes the EEG patterns in a predefined time window and has 2 to 3 degrees of freedom.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

An Interface Damage Model for the Simulation of Delamination Under Variable-Mode Ratio in Composite Materials

A thermodynamically consistent damage model for the simulation of progressive delamination under variable mode ratio is presented. The model is formulated in the context of the Damage Mechanics. The constitutive equation that results from the definition of the free energy as a function of a damage variable is used to model the initiation and propagation of delamination. A new delamination initiation criterion is developed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. The formulation proposed accounts for crack closure effets avoiding interfacial penetration of two adjacent layers aftercomplete decohesion. The model is implemented in a finite element formulation. The numerical predictions given by the model are compared with experimental results

Efeitos dos parâmetros operacionais na fotodegradação do azo corante direct red 23 na interface dióxido de titânio/água

The decolorization and degradation of direct red 23 azo dye have been investigated in aqueous suspension of titanium dioxide under artificial irradiation. The effects of some operational parameters such as azo dye concentration, catalyst loading, and solution pH were investigated at 30.0 ºC and optimized values were obtained. The first-order kinetic model was used to discuss the results. The UV-Vis spectra changes showed that the azo dye sample, collected after 6 h irradiation, was 98% decolorized while the residual total carbon was 97.9% degraded, indicating simultaneous photodecolorization and degradation.

Palveluväylän hyödyntäminen palvelukeskeisessä arkkitehtuurissa

Palvelukeskeinen arkkitehtuuri on uusi tapa rakentaa tietojärjestelmiä. Se perustuu siihen, että logiikasta koostetaan yleiskäyttöisiä palveluita, joita tarjotaan muiden järjestelmän osien käyttöön. Tällöin samoja asioita ei tarvitse toteuttaa moneen kertaan ja järjestelmää voidaan hyödyntää tehokkaasti ja monipuolisesti. Näiden palveluiden hallinnassa voidaan hyödyntää palveluväyliä, eli ESB -tuotteita. Palveluväylät sisältävät erilaisia mekanismeja, joiden avulla palveluihin liittyvää viestiliikennettä voidaan reitittää, muokata ja valvoa eri tavoin. Nykyisissä palvelukeskeisissä toteutuksissa käytetään usein XML -kieleen pohjautuvia Web Service -määrityksiä. Ne tarjoavat ympäristöriippumattoman pohjan, joka täyttää suoraan useita palvelukeskeisen arkkitehtuurin vaatimuksia. Määritysten ympärille on myös paljon valmiita laajennuksia, joiden avulla palveluihin voidaan liittää lisätoiminnallisuutta. Lahden kaupunki lähti Fenix -projektin yhteydessä kehittämään uutta kuntien käyttöön soveltuvaa järjestelmää, joka hyödyntää palvelukeskeisen arkkitehtuurin periaatteita. Järjestelmä jaettiin selkeisiin kerroksiin siten, että käyttöliittymä erotettiin palvelulogiikoista palveluväylän avulla. Tällöin järjestelmä saatiin jaettua loogisiin kokonaisuuksiin, joilla on selkeä rooli. Taustapalvelut hoitavat käsitteiden hallinnan, sekä niihin liittyvät liiketoimintasäännöt. Käyttöliittymäkerros hoitaa tiedon esittämisen ja tarjoaa graafisen, selainpohjaisen käyttöliittymän palveluihin. Palveluväylä hoitaa liikenteen reitittämisen, sekä huolehtii palveluihin liittyvistä käyttöoikeuksista ja tilastoinnista. Lopputuloksena on loputtomiin laajennettavissa oleva järjestelmä, jonka päälle voidaan kehittää erilaisia sähköisiä palveluita kunnan ja sen asukkaiden välille.

Fluxos de óxido nitroso na interface ar-mar na Baía de Guanabara

In Surface water concentrations of N2O were measured at 37 stations in Guanabara Bay and fluxes estimated across the air-sea interface. Concentrations averaged 8.2 ± 2.2 nmol L-1 and 90% of the stations showed supersaturation averaging 33%. N2O fluxes were estimated using a two-film model which is given by the product of the concentration difference across the film and the gas transfer coefficient (k w). Two parametrizations of k w were used which provided average fluxes of 0.3 and 3.0 µg N m-2 h-1. Flux measurements using floating chambers (not reported here) seem to agree with the upper limit of these estimates.

Diretrizes para a formação de professores da educação básica em interface com a licenciatura em química: em contexto as possibilidades formativas

We developed and applied an educational instrument (ID) to discuss, in the discipline of Supervised Pre Service Teachers Practice 1, guidelines for teacher education to redefine teacher knowledge with a specific focus on chemistry teachers. The study used methodological fundamentals of Discursive Textual Analysis that involves identifying and isolating a set of materials subjected to analysis, categorizing these statements and producing texts, integrating these descriptions and interpretations, basing its construction on the category system built. Data were collected through participant observation and text readings used by the students in performing the activity. It was noted that the chemistry teachers trained were able to express opinions that indicated the Construction of Meanings Interface that was the category of analysis established a priori.

Improving and User Interface to E-Procurement Software Used in Asset Accounting and Investigating Effects to Efficiency

This diploma thesis has been done to international organization which takes care from the accounting actions of two major companies. In this organization are used three different purchasing tools which are used when new asset master data is wanted to input to SAP R/3- system. The aim of this thesis is to find out how much changing the user interface of one of these three e-procurement programs will affect to overall efficiency in asset accounting. As an addition will be introduced project framework which can be used in future projects and which help to avoid certain steps in the development process. At the moment data needs to be inputted manually with many useless mouse clicks and data needs to be searched from many various resources which slow down the process. Other organization has better tools at the moment than the myOrders system which is under investigation Research was started by exploring the main improvement areas. After this possible defects were traced. Suggested improvements were thought by exploring literature which has been written from usability design and research. Meanwhile also directional calculations from the benefits of the project were done alongside with the analysis of the possible risks and threats. After this NSN IT approved the changes which they thought was acceptable. The next step was to program them into tool and test them before releasing to production environment. The calculations were made also from implemented improvements and compared them to planned ones From whole project was made a framework which can be utilized also to other similar projects. The complete calculation was not possible because of time schedule of the project. Important observation in the project was that efficiency is not improved not only by changing the GUI but also improving processes without any programming. Feedback from end user should be also listened more in development process. End-user is after all the one who knows the best how the program should look like.

Fragment d'un discours d'une méthode

Ce qui suit est le début de la présentation d'une sélection de mes articles, traduits en portugais, et supposés représentatifs de la "méthode" que j'ai pratiquée dans mes publications. J'y retrace en détail deux épisodes déjà anciens de "l'histoire de mon esprit" (si j'ose employer une expression de Descartes), qui ont fortement influencé mes travaux ultérieurs, en m'incitant à tout faire pour concilier le respect de la "lettre" avec le souci de "l'esprit", et l'attention aux genèses avec l'analyse des structure.

Perspectives interculturelles et interlinguistiques sur le discours académique – Crosscultural and Crosslinguistic Perspectives on Academic Discourse. Volume 1

The Department of French Studies of the University of Turku (Finland) organized an International Bilingual Conference on Crosscultural and Crosslinguistic Perspectives on Academic Discourse from 2022 May 2005. The event hosted specialists on Academic Discourse from Belgium, Finland, France, Germany, Italy, Norway, Spain, and the USA. This book is the first volume in our series of publications on Academic Discourse (AD hereafter). The following pages are composed of selected papers from the conference and focus on different aspects and analytical frameworks of Academic Discourse. One of the motivations behind organizing the conference was to examine and expand research on AD in different languages. Another one was to question to what extent academic genres are culturebound and language specific or primarily field or domain specific. The research carried out on AD has been mainly concerned with the use of English in different academic settings for a long time now – mainly written contexts – and at the expense of other languages. Alternatively the academic genre conventions of English and English speaking world have served as a basis for comparison with other languages and cultures. We consider this first volume to be a strong contribution to the spreading out of researches based on other languages than English in AD, namely Finnish, French, Italian, Norwegian and Romanian in this book. All the following articles have a strong link with the French language: either French is constitutive of the AD corpora under examination or the article was written in French. The structure of the book suggests and provides evidence that the concept of AD is understood and tackled to varying degrees by different scholars. Our first volume opens up the discussion on what AD is and backs dissemination, overlapping and expansion of current research questions and methodologies. The book is divided into three parts and contains four articles in English and six articles in French. The papers in part one and part two cover what we call the prototypical genre of written AD, i.e. the research article. Part one follows up on issues linked to the 13 Research Article (RA hereafter). Kjersti Fløttum asks wether a typical RA exists and concentrates on authors’ voices in RA (self and other dimensions), whereas Didriksen and Gjesdal’s article focuses on individual variation of the author’s voice in RA. The last article in this section is by Nadine Rentel and deals with evaluation in the writing of RA. Part two concentrates on the teaching and learning of AD within foreign language learning, another more or less canonical genre of AD. Two aspects of writing are covered in the first two articles: foreign students’ representations on rhetorical traditions (Hidden) and a contrastive assessment of written exercices in French and Finnish in Higher Education (Suzanne). The last contribution in this section on AD moves away from traditional written forms and looks at how argumentation is constructed in students’ oral presentations (Dervin and Fauveau). The last part of the book continues the extension by featuring four articles written in French exploring institutional and scientific discourses. Institutional discourses under scrutiny include the European Bologna Process (Galatanu) and Romanian reform texts (Moilanen). As for scientific discourses, the next paper in this section deconstructs an ideological discourse on the didactics of French as a foreign language (Pescheux). Finally, the last paper in part three reflects on varied forms of AD at university (Defays). We hope that this book will add some fuel to continue discussing diverse forms of and approches to AD – in different languages and voices! No need to say that with the current upsurge in academic mobility, reflecting on crosscultural and crosslinguistic AD has just but started.

O Cuidado Empático: Contribuições para a Ética e Sua Interface com a Educação Moral na Formação em Saúde

RESUMO O presente artigo apresenta alguns pontos essenciais do pensamento do filósofo Michael Slote em sua obra “The ethics of care and empathy”. Situamos a sua produção no contexto em que a ética do cuidado foi desenvolvida e problematizada, evidenciando, sobretudo, a questão de gênero que atravessa essa perspectiva ética. Assim, convocamos autores e autoras que dialogam estreitamente com as questões levantadas por Slote como interlocutores fundamentais para se pensar a empatia como componente fundamental da ética do cuidado. Em sequência, resgatamos o sentido ontológico do cuidado e da responsabilidade, correlacionando-os com a prática do cuidado em saúde. Ao final, apresentamos um caso paradigmático para um debate concreto da ética do cuidado e empatia no âmbito da educação moral, destacando sua importância no processo de formação dos profissionais de saúde no Brasil.