Produção e estudo de multicamadas magnéticas em substrato flexível

Magnetic multilayers are the support for the production of spintronic devices, representing great possibilities for miniaturized electronics industry. having the control to produce devices as well as their physical properties from simple multilayer films to highly complex at the atomic scale is a fundamental need for progress in this area, in recent years has highlighted the production of organic and flexible spintronic devices. Because of this trend, the objective of this work was to produce magnetic multilayers deposited on flexible substrate using magnetron sputtering dc technique. Three sets of samples were prepared. The first set composed of the trilayer type CoFe=Cu(t)=CoFe with different thickness of the metallic spacer. The second set consists of two multilayer subgroups, CoFe=Cu in the presence of IrMn layer as a buffer and the next multilayer as cap layer. The third set consisting of non-magnetostrictive multilayer permalloy (Py=Ta and Py=Ag) on flexible substrate and glass. The magnetic properties, were investigated by magnetometry measurements, ferromagnetic resonance and magnetoimpedance (MI), measurements were carried out at room temperature with the magnetic field always applied on the sample plane. For structural analysis, the diffraction X-ray was used. The results of the trilayer showed a high uniaxial anisotropy field for the sample with a spacer of 4.2 nm. For the multilayer in the presence of IrMn layer as the buffer, the study of static and dynamic magnetic properties showed isotropic behavior. For the multilayer in the presence of IrMn layer as a cap, the results of static magnetic properties of the magnetic behavior exhibited a spin valve structure type. However there was a disagreement with results of ferromagnetic resonance measurements, which was justified by the contribution of the unstable and stable grain to the rotatable anisotropy and Exchange bias in ferromagneticantiferromagnetic interface. The third serie of samples showed similar results behavior for the MI Ag multilayers spacer in both substrates. There are also significant MI changes with the Ta spacer, possible associated with the compressive stress on the flexible substrate sample.

Método híbrido para projeto de superfícies seletivas em frequência

This thesis presents a hybrid technique of frequency selective surfaces project (FSS) on a isotropic dielectric layer, considering various geometries for the elements of the unit cell. Specifically, the hybrid technique uses the equivalent circuit method in conjunction with genetic algorithm, aiming at the synthesis of structures with response single-band and dual-band. The equivalent circuit method allows you to model the structure by using an equivalent circuit and also obtaining circuits for different geometries. From the obtaining of the parameters of these circuits, you can get the transmission and reflection characteristics of patterned structures. For the optimization of patterned structures, according to the desired frequency response, Matlab™ optimization tool named optimtool proved to be easy to use, allowing you to explore important results on the optimization analysis. In this thesis, numeric and experimental results are presented for the different characteristics of the analyzed geometries. For this, it was determined a technique to obtain the parameter N, which is based on genetic algorithms and differential geometry, to obtain the algebraic rational models that determine values of N more accurate, facilitating new projects of FSS with these geometries. The optimal results of N are grouped according to the occupancy factor of the cell and the thickness of the dielectric, for modeling of the structures by means of rational algebraic equations. Furthermore, for the proposed hybrid model was developed a fitness function for the purpose of calculating the error occurred in the definitions of FSS bandwidths with transmission features single band and dual band. This thesis deals with the construction of prototypes of FSS with frequency settings and band widths obtained with the use of this function. The FSS were initially reviewed through simulations performed with the commercial software Ansoft Designer ™, followed by simulation with the equivalent circuit method for obtaining a value of N in order to converge the resonance frequency and the bandwidth of the FSS analyzed, then the results obtained were compared. The methodology applied is validated with the construction and measurement of prototypes with different geometries of the cells of the arrays of FSS.

Método híbrido para projeto de superfícies seletivas em frequência

This thesis presents a hybrid technique of frequency selective surfaces project (FSS) on a isotropic dielectric layer, considering various geometries for the elements of the unit cell. Specifically, the hybrid technique uses the equivalent circuit method in conjunction with genetic algorithm, aiming at the synthesis of structures with response single-band and dual-band. The equivalent circuit method allows you to model the structure by using an equivalent circuit and also obtaining circuits for different geometries. From the obtaining of the parameters of these circuits, you can get the transmission and reflection characteristics of patterned structures. For the optimization of patterned structures, according to the desired frequency response, Matlab™ optimization tool named optimtool proved to be easy to use, allowing you to explore important results on the optimization analysis. In this thesis, numeric and experimental results are presented for the different characteristics of the analyzed geometries. For this, it was determined a technique to obtain the parameter N, which is based on genetic algorithms and differential geometry, to obtain the algebraic rational models that determine values of N more accurate, facilitating new projects of FSS with these geometries. The optimal results of N are grouped according to the occupancy factor of the cell and the thickness of the dielectric, for modeling of the structures by means of rational algebraic equations. Furthermore, for the proposed hybrid model was developed a fitness function for the purpose of calculating the error occurred in the definitions of FSS bandwidths with transmission features single band and dual band. This thesis deals with the construction of prototypes of FSS with frequency settings and band widths obtained with the use of this function. The FSS were initially reviewed through simulations performed with the commercial software Ansoft Designer ™, followed by simulation with the equivalent circuit method for obtaining a value of N in order to converge the resonance frequency and the bandwidth of the FSS analyzed, then the results obtained were compared. The methodology applied is validated with the construction and measurement of prototypes with different geometries of the cells of the arrays of FSS.

Estudo fitoquímico e biológico das folhas de Banisteriopsis argyrophylla (A. Juss.) B. Gates (Malpighiaceae)

With the increasing fungi resistance compared with existing drugs on the market and the side effects reported by some compounds with antioxidant properties and enzymatic inhibitors, in particular against α-amylase and α-glucosidase, the discovery of new compounds with biological potential, becomes a need. In this context, natural products can be an important source for the discovery of new active molecular architectures. Then, this study aimed to evaluate the antioxidant activity, the enzymatic inhibitory activity of α-amylase and α-glucosidase, the antifungal and cytotoxic activities of ethanolic extract (EE) the leaves of Banisteriopsis argyrophylla (Malpighiaceae) and their fractions, obtained by liquid-liquid extraction using solvents of increasing polarity. The antioxidant activity was evaluated by the free radical DPPH scavenging method (2,2-diphenyl-1-picrylhydrazyl) and the ethyl acetate fractions (FAE) and n-butanol (FB) were the most active, confirmed by the peak current and the oxidation potential obtained by differential pulse voltammetry (DPV). The inhibitory activity of the α-amylase and α-glucosidase was analyzed considering the reactions between substrates α-(2-chloro-4-nitrophenyl)-β-1,4-galactopiranosilmaltoside (Gal-α-G2-CNP) and 4-nitrophenyl-α-D-glucopyranoside (p-NPG), respectively. Initially, it was found that the EE showed considerable activity against α-amylase (EC50 = 2.89±0.1 μg m L–1) compared to the acarbose used as positive control (EC50 = 0.08±0.1 μg mL–1) and that did not showed promising activity against the α-glucosidase. After this observation we evaluated the inhibitory activity of α-amylase fractions, with FAE (EC50 = 2.33±0.1 μg mL–1) and FB (EC50 = 2.57 ± 0.1 μg mL–1) showing the best inhibitions. The antifungal activity was evaluated against Candida species, and the FAE had better antifungal potential (MIC's between 93.75 and 11.72 μg mL–1) compared with amphotericin as positive standard (MIC = 1.00 and 2.00 μg L–1 for C. parapsilosis and C. krusei used as controls, respectively). The EE (CC50 = 360.00 ± 12 μg mL–1) and fractions (CC50's> 270.00 μg mL–1) were considerably less toxic to Vero cells than the cisplatin used as positive control (CC50 = 7.01 ± 0 6 μg mL–1). The FAE showed the best results for the activities studied, this fraction was submitted to ultra performance liquid chromatography coupled with mass spectrometry (UPLC-MS)), and the following flavonoids have been identified: (±)-catechin, quercetin-3-O-β-D-Glc/ quercetin-3-O-β-D-Gal, quercetin-3-O-β-L-Ara, quercetin-3-O-β-D-Xyl, quercetin-3-O-α-L-Rha, kaempferol-3-O-α-L-Rha, quercetin-3-O-(2''-galoil)-α-L-Rha, quercetin-3-O-(3''-galoil)-α-L-Rha and kaempferol-3-O-(3''-galoil)-α-L-Rha,. FAE was submitted to column chromatography using C18 phase, and (±)-catechin was isolated (FAE-A1, 73 mg) and three fractions consisting of a mixture of flavonoids were obtained (FAE-A2, FAE-A3 and FAE-A4). These compounds were identified by thin layer chromatography (TLC) and (–)-ESI-MS. The (±)-catechin fraction showed an MIC = 2.83 μg ml–1 in assay using C. glabrata, with amphotericin as positive control. The fractions FAE-A2, FAE-A3, FAE-A4, showed less antifungal potential in tested concentrations. The identified flavonoids are described in the literature, regarding their antioxidant capacity and (±)-catechin, quercetin-3-O-Rha and kaempferol-3-O-Rha are described as α-amylase inhibitors. Thus, B. argyrophylla is an important species that produces compounds with antioxidant potential that can be related to the traditional use as anti-inflammatory and also has antifungal compounds and inhibitors of α-amylase. Therefore, these leaves are promising resources for the production of new drugs.

Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas

ALVES, Ana paula Melo. Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas. 2009. 124 f. Tese (Doutorado em Quimica) - Centro de Ciências Exatas e da Natureza, Universidade Federal da Paraíba, João Pessoa, PB, 2009.

Fibronectin/phosphorylcholine coatings on fluorocarboned surfaces: a study upon adsorption and grafting processes

Depuis ces dernières décennies, le domaine des biomatériaux a connu un essor considérable, évoluant de simples prothèses aux dispositifs les plus complexes pouvant détenir une bioactivité spécifique. Outre, le progrès en science des matériaux et une meilleure compréhension des systèmes biologiques a offert la possibilité de créer des matériaux synthétiques pouvant moduler et stimuler une réponse biologique déterminée, tout en améliorant considérablement la performance clinique des biomatériaux. En ce qui concerne les dispositifs cardiovasculaires, divers recouvrements ont été développés et étudiés dans le but de modifier les propriétés de surface et d’améliorer l’efficacité clinique des tuteurs. En effet, lorsqu’un dispositif médical est implanté dans le corps humain, son succès clinique est fortement influencé par les premières interactions que sa surface établit avec les tissus et les fluides biologiques environnants. Le recouvrement à la surface de biomatériaux par diverses molécules ayant des propriétés complémentaires constitue une approche intéressante pour atteindre différentes cibles biologiques et orienter la réponse de l’hôte. De ce fait, l’élucidation de l’interaction entre les différentes molécules composant les recouvrements est pertinente pour prédire la conservation de leurs propriétés biologiques spécifiques. Dans ce travail, des recouvrements pour des applications cardiovasculaires ont été créés, composés de deux molécules ayant des propriétés biologiques complémentaires : la fibronectine (FN) afin de promouvoir l’endothélialisation et la phosphorylcholine (PRC) pour favoriser l’hémocompatibilité. Des techniques d’adsorption et de greffage ont été appliquées pour créer différents recouvrements de ces deux biomolécules sur un polymère fluorocarboné déposé par traitement plasma sur un substrat en acier inoxydable. Dans un premier temps, des films de polytétrafluoroéthylène (PTFE) ont été utilisés en tant que surface modèle afin d’explorer l’interaction de la PRC et de la FN avec les surfaces fluorocarbonées ainsi qu’avec des cellules endothéliales et du sang. La stabilité des recouvrements de FN sur l’acier inoxydable a été étudiée par déformation, mais également par des essais statiques et dynamiques sous-flux. Les recouvrements ont été caractérisés par Spectroscopie Photoéléctronique par Rayons X, immunomarquage, angle de contact, Microscopie Électronique de Balayage, Microscopie de Force Atomique et Spectrométrie de Masse à Ionisation Secondaire à Temps de Vol (imagerie et profilage en profondeur). Des tests d’hémocompatibilité ont été effectués et l’interaction des cellules endothéliales avec les recouvrements a également été évaluée. La FN greffée a présenté des recouvrements plus denses et homogènes alors que la PRC quant à elle, a montré une meilleure homogénéité lorsqu’elle était adsorbée. La caractérisation de la surface des échantillons contenant FN/PRC a été corrélée aux propriétés biologiques et les recouvrements pour lesquels la FN a été greffée suivie de l’adsorption de la PRC ont présenté les meilleurs résultats pour des applications cardiovasculaires : la promotion de l’endothélialisation et des propriétés d’hémocompatibilité. Concernant les tests de stabilité, les recouvrements de FN greffée ont présenté une plus grande stabilité et densité que dans le cas de l’adsorption. En effet, la pertinence de présenter des investigations des essais sous-flux versus des essais statiques ainsi que la comparaison des différentes stratégies pour créer des recouvrements a été mis en évidence. D’autres expériences sont nécessaires pour étudier la stabilité des recouvrements de PRC et de mieux prédire son interaction avec des tissus in vivo.

"O que é que há? O que é que está se passando" nessas cabeças? : um estudo sobre a concepção de projetos recentes da arquitetura residencial unifamiliar em Natal

L étude se fonde sur la recherche du processus inhérent à la conception du projet par le biais de l approche architecturologique proposée par Philippe Boudon et al (2000) ; un modèle théorique qui sert de fondement à la construction d une connaissance de l architecture au moyen d une étude de la nature des opérations mentales de chaque architecte lorsqu il organise son travail de conception. La modélisation de l architecturologie concentre son étude sur le travail qui a lieu avant même la confection matérielle du projet (représentation graphique finale). De cette façon, douze projets furent analysés d architecture résidencielle unifamiliale; conçus récemment par six architectes « potiguares » pour Natal et sa région périphérique. Les résultats mettent en évidence un ensemble de modèles substrats (comme point de départ) et téléologiques (comme point d arrivée) adoptés par les auteurs au cours de la conception de leurs projets. Ces modèles, de façon générale, sont liés aux pertinences socio-culturelles (conventions, formes traditionnelles ou coutumes) du contexte pour lesquels ils sont conçus (lotissements privés de co-propriété des classes moyennes et moyennes-supérieures) et en même temps, ils sont le fruit de croyances, d idéologies et d expériences antérieures propres à l espace de la conception de chaque architecte

Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas

ALVES, Ana paula Melo. Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas. 2009. 124 f. Tese (Doutorado em Quimica) - Centro de Ciências Exatas e da Natureza, Universidade Federal da Paraíba, João Pessoa, PB, 2009.

Functional alkali tantalate 2D structures for microelectronics and related applications

Alkali tantalates and niobates, including K(Ta / Nb)O3, Li(Ta / Nb)O3 and Na(Ta / Nb)O3, are a very promising ferroic family of lead-free compounds with perovskite-like structures. Their versatile properties make them potentially interesting for current and future application in microelectronics, photocatalysis, energy and biomedics. Among them potassium tantalate, KTaO3 (KTO), has been raising interest as an alternative for the well-known strontium titanate, SrTiO3 (STO). KTO is a perovskite oxide with a quantum paraelectric behaviour when electrically stimulated and a highly polarizable lattice, giving opportunity to tailor its properties via external or internal stimuli. However problems related with the fabrication of either bulk or 2D nanostructures makes KTO not yet a viable alternative to STO. Within this context and to contribute scientifically to the leverage tantalate based compounds applications, the main goals of this thesis are: i) to produce and characterise thin films of alkali tantalates by chemical solution deposition on rigid Si based substrates, at reduced temperatures to be compatible with Si technology, ii) to fulfil scientific knowledge gaps in these relevant functional materials related to their energetics and ii) to exploit alternative applications for alkali tantalates, as photocatalysis. In what concerns the synthesis attention was given to the understanding of the phase formation in potassium tantalate synthesized via distinct routes, to control the crystallization of desired perovskite structure and to avoid low temperature pyrochlore or K-deficient phases. The phase formation process in alkali tantalates is far from being deeply analysed, as in the case of Pb-containing perovskites, therefore the work was initially focused on the process-phase relationship to identify the driving forces responsible to regulate the synthesis. Comparison of phase formation paths in conventional solid-state reaction and sol-gel method was conducted. The structural analyses revealed that intermediate pyrochlore K2Ta2O6 structure is not formed at any stage of the reaction using conventional solid-state reaction. On the other hand in the solution based processes, as alkoxide-based route, the crystallization of the perovskite occurs through the intermediate pyrochlore phase; at low temperatures pyrochlore is dominant and it is transformed to perovskite at >800 °C. The kinetic analysis carried out by using Johnson-MehlAvrami-Kolmogorow model and quantitative X-ray diffraction (XRD) demonstrated that in sol-gel derived powders the crystallization occurs in two stages: i) at early stage of the reaction dominated by primary nucleation, the mechanism is phase-boundary controlled, and ii) at the second stage the low value of Avrami exponent, n ~ 0.3, does not follow any reported category, thus not permitting an easy identification of the mechanism. Then, in collaboration with Prof. Alexandra Navrotsky group from the University of California at Davis (USA), thermodynamic studies were conducted, using high temperature oxide melt solution calorimetry. The enthalpies of formation of three structures: pyrochlore, perovskite and tetragonal tungsten bronze K6Ta10.8O30 (TTB) were calculated. The enthalpies of formation from corresponding oxides, ∆Hfox, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -203.63 ± 2.84 kJ/mol, - 358.02 ± 3.74 kJ/mol, and -1252.34 ± 10.10 kJ/mol, respectively, whereas from elements, ∆Hfel, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -1408.96 ± 3.73 kJ/mol, -2790.82 ± 6.06 kJ/mol, and -13393.04 ± 31.15 kJ/mol, respectively. The possible decomposition reactions of K-deficient KTa2.2O6 pyrochlore to KTaO3 perovskite and Ta2O5 (reaction 1) or to TTB K6Ta10.8O30 and Ta2O5 (reaction 2) were proposed, and the enthalpies were calculated to be 308.79 ± 4.41 kJ/mol and 895.79 ± 8.64 kJ/mol for reaction 1 and reaction 2, respectively. The reactions are strongly endothermic, indicating that these decompositions are energetically unfavourable, since it is unlikely that any entropy term could override such a large positive enthalpy. The energetic studies prove that pyrochlore is energetically more stable phase than perovskite at low temperature. Thus, the local order of the amorphous precipitates drives the crystallization into the most favourable structure that is the pyrochlore one with similar local organization; the distance between nearest neighbours in the amorphous or short-range ordered phase is very close to that in pyrochlore. Taking into account the stoichiometric deviation in KTO system, the selection of the most appropriate fabrication / deposition technique in thin films technology is a key issue, especially concerning complex ferroelectric oxides. Chemical solution deposition has been widely reported as a processing method to growth KTO thin films, but classical alkoxide route allows to crystallize perovskite phase at temperatures >800 °C, while the temperature endurance of platinized Si wafers is ~700 °C. Therefore, alternative diol-based routes, with distinct potassium carboxylate precursors, was developed aiming to stabilize the precursor solution, to avoid using toxic solvents and to decrease the crystallization temperature of the perovskite phase. Studies on powders revealed that in the case of KTOac (solution based on potassium acetate), a mixture of perovskite and pyrochlore phases is detected at temperature as low as 450 °C, and gradual transformation into monophasic perovskite structure occurs as temperature increases up to 750 °C, however the desired monophasic KTaO3 perovskite phase is not achieved. In the case of KTOacac (solution with potassium acetylacetonate), a broad peak is detected at temperatures <650 °C, characteristic of amorphous structures, while at higher temperatures diffraction lines from pyrochlore and perovskite phases are visible and a monophasic perovskite KTaO3 is formed at >700 °C. Infrared analysis indicated that the differences are due to a strong deformation of the carbonate-based structures upon heating. A series of thin films of alkali tantalates were spin-coated onto Si-based substrates using diol-based routes. Interestingly, monophasic perovskite KTaO3 films deposited using KTOacac solution were obtained at temperature as low as 650 °C; films were annealed in rapid thermal furnace in oxygen atmosphere for 5 min with heating rate 30 °C/sec. Other compositions of the tantalum based system as LiTaO3 (LTO) and NaTaO3 (NTO), were successfully derived as well, onto Si substrates at 650 °C as well. The ferroelectric character of LTO at room temperature was proved. Some of dielectric properties of KTO could not be measured in parallel capacitor configuration due to either substrate-film or filmelectrode interfaces. Thus, further studies have to be conducted to overcome this issue. Application-oriented studies have also been conducted; two case studies: i) photocatalytic activity of alkali tantalates and niobates for decomposition of pollutant, and ii) bioactivity of alkali tantalate ferroelectric films as functional coatings for bone regeneration. Much attention has been recently paid to develop new type of photocatalytic materials, and tantalum and niobium oxide based compositions have demonstrated to be active photocatalysts for water splitting due to high potential of the conduction bands. Thus, various powders of alkali tantalates and niobates families were tested as catalysts for methylene blue degradation. Results showed promising activities for some of the tested compounds, and KNbO3 is the most active among them, reaching over 50 % degradation of the dye after 7 h under UVA exposure. However further modifications of powders can improve the performance. In the context of bone regeneration, it is important to have platforms that with appropriate stimuli can support the attachment and direct the growth, proliferation and differentiation of the cells. In lieu of this here we exploited an alternative strategy for bone implants or repairs, based on charged mediating signals for bone regeneration. This strategy includes coating metallic 316L-type stainless steel (316L-SST) substrates with charged, functionalized via electrical charging or UV-light irradiation, ferroelectric LiTaO3 layers. It was demonstrated that the formation of surface calcium phosphates and protein adsorption is considerably enhanced for 316L-SST functionalized ferroelectric coatings. Our approach can be viewed as a set of guidelines for the development of platforms electrically functionalized that can stimulate tissue regeneration promoting direct integration of the implant in the host tissue by bone ingrowth and, hence contributing ultimately to reduce implant failure.

Cimentos convencionais e adesivos na cimentação final em prótese fixa

Os cimentos dentários na função de preencher a interface entre a superfície dentária e superfície interna da prótese nos coloca frente a uma diversidade de substratos e técnicas. O presente trabalho visou rever conceitos associados aos cimentos dentários, a evolução destes materiais junto aos diferentes sistemas cerâmicos e suas limitações no seu universo bem como a estratégia da sua aplicação em superfícies resistentes ou não ao ácido condicionante. Para alcançar a resposta de qual o melhor método na escolha de um material para cimentação de próteses fixas, este trabalho também apresenta uma comparação entre os cimentos dentários convencionais e resinosos. Este trabalho consiste numa revisão bibliográfica de forma a pesquisar de forma geral os cimentos de uso na medicina dentária. Foi realizada uma pesquisa, em abril de 2016, nas bases de dados da PubMed e B-on e em obras de caráter científico com o intuito de recolher informações sobre o assunto em um intervalo temporal de 10 anos. Os critérios escolhidos foram casos clínicos, revisão de literatura e estudos in vitro, segundo o seu rigor científico e interesse para o tema. O resultado sobre os testes de resistência utilizados nos estudos, os testes de aderência do cimento ao dente podem variar amplamente. O tratamento de superfícies e a evolução tecnológica podem ser eficazes na escolha desses materiais, bem como a comparação dos tipos de falhas que ocorrem na interface adesivas. A conclusão que se obteve é que os materiais raramente são comparados com um padrão e muitas vezes as condições experimentais variam.

Potencial do óleo de Aloysia citriodora Palau no controle de fitopatógenos e na indução de resistência ao tombamento de plântulas de feijão, pepino e beterraba

The crops are affected by pests and diseases that decrease productivity. Among them are the damping off of seedlings that can occur in pre and post-emergence. In bean crops, cucumber and beet these diseases occur, being caused by various pathogens, especialy fitopathogenic fungi. Several measures are used for the controle of such diseases, among them, is the chemical seed treatment fungicides. However, society has become increasingly concerned about the quality and food and environmental contamination, generation a growting search for sensitive products to humans and the environment. The use of essential oils to control plant pathogens is an example of alternative tested by science in the search for less aggressive technologies. This study aimed to evaluate the efficiency of the use of essential oil Aloysia citriodora, in control of pathogens causing damping off in beans, cucumber and beet. This thesis was divided in four chapters, the introductory first, and the other addressing the control of Pythium sp. in beans, Sclerotinia sclerotiorum on cucumber, and Fusarium sp. on beet. The methodology consisted of four experiments in each pathosystem, with all the work done at the Federal Technological University of Parana, Campus Dois Vizinhos. In the first experiment evaluated the fungistatic and fungicidal effect of the essential oil of A. citriodora on PDA in vitro in mycelial growth of pathogens studied. In the second experiment evaluated the in vitro effect of essential oil concentrations of A. citriodora in BD medium on microscope slides, on the germination of sporangia Pythium sp. and conidia Fusarium sp., and in Petri dishes with PDA medium, the sclerotia germination speed index of S. sclerotiorum. In the third experiment, we evaluated in germination test in paper roll (PR), the phytotoxic effect or not the use of essential oil concentrations of A. citriodora in dry bean seed, cucumber and beet. The variables used to assess this experiment were the germination percentage, mediun green mass per plant and average length of seedlings. In the fourth experiment we assessed the effect of treating bean seeds, cucumber and beet with essential oil contents of A. citriodora, seeds in their subsequent substrates contamined with pathogens studied, Pythium sp., S. sclerotiorum and Fusarium sp. In this experiment we used the following variables: percentage of emergence, percentage of post-emergence damping off, green average mass per plant, average length per plant and biochemical analyzes. The biochemistry of plant tissues evaluated were as follows: protein content, enzymatic activities of peroxidases, phenylalanine ammonia-liase (PAL), chitinases and β-1,3-glucanases. The in vitro results show that the essential oil has fungistatic and fungicidal effect on mycelial growth, on sporangia germination, conidia and sclerotia of the pathogens studied in this work, wich may be related to its major components, citral and limonene. The oil also exhibits low phytotoxicity to seeds of the species studied, only in beans decreases germination in most studied dosage (0,25%), cucumber also in the higher dosage (0,25%) reduce the length of seedlings, and beet there were no negative effects to the seedlings. In the test in substrate contaminated with the pathogens, the use of essential oil: increased germination and decreased post emergence damping off of beans seedlings; at a concentration of 0,0625% decreases post emergence damping off in cucumber. In biochemical analyzes found an increase in the enzymatic activity of peroxidases and β-1,3-glucanases on beans, and glucanases on cucumber, and increased enzyme activity of peroxidases on beet, showing action in resistance induction at damping off.

Produção biológica integrada de hidrogénio e metano a partir de resíduos da indústria do biodiesel

Dissertação de Mestrado Integrado em Engenharia da Energia e do Ambiente

Produção de lipidios funcionais por ação de lipase fúngica

A modificação estrutural de óleos e gorduras é uma das principais áreas de interesse de pesquisa em diferentes setores industriais. No caso da indústria de alimentos, a interesterificação é empregada para melhorar propriedades nutricionais e funcionais, em que se obtêm compostos diferentes dos que lhes deram origem. As lipases microbianas são os biocatalisadores mais utilizados industrialmente, por serem mais estáveis, específicas e com propriedades bem mais diversificadas que as lipases de outras fontes. Este trabalho objetivou, primeiramente, a caracterização da gordura da pele de frango (GPF) e sua comparação com óleo de soja, como referência, visando a utilização de GPF em reações de interesterificação. Para isto foram caracterizados quanto aos índices de rancidez hidrolítica e oxidativa, bem como de matéria insaponificável, índices de saponificação, refração e iodo. Foi realizado ainda o fracionamento e perfil de ácidos graxos destes lipídios e suas frações, com o cálculo de seus índices nutricionais. Foi verificado que a GPF apresentou qualidade satisfatória devido aos baixos índices de acidez (0,65 g ácido oleico.100 g -1 ), peróxido (2,14 meq.kg-1 ), p-anisidina (0,70 unidades de absorvância.g-1 ), além de fonte de ácidos graxos mono-insaturados (40%), sendo fonte promissora para estudos de interesterificação. Em um segundo momento o objetivo foi produzir lipídios modificados ricos em ácidos graxos essenciais a partir da gordura da pele de frango e ácidos graxos ramificados, utilizando lipase sn-1,3 específica e interesterificação do tipo acidólise. Foram estudados os fatores concentração de enzima, adição de água, proporção de substratos e tempo, segundo um planejamento experimental fatorial completo 2 4 . As separações analíticas foram executadas em placas de cromatografia de camada delgada, sendo as frações posteriormente extraídas, ressuspensas e injetadas no cromatógrafo a gás. Foi verificado que a adição de água ao meio reacional apresentou efeito significativo (p<0,05) para todos ácidos graxos avaliados dos triacilgliceróis, sendo que para o ácido essencial linoleico (C18:2) o efeito do tempo de reação também foi significativo, sendo verificado que quanto maior o tempo de reação, menor a quantidade de água a ser adicionada. Em um terceiro momento, o objetivo foi produzir éster fenólico a partir do DHCA, além de realizar reações de transesterificação deste éster com tricaprilina. Para a reação de transesterificação, foi utilizado um delineamento composto central rotacional (DCCR) variando a quantidade de enzima, tempo de reação e temperatura sobre a resposta (%) dos reagentes consumidos. A lipase Novozym® 435 de Candida antarctica foi utilizada como catalisador de todas reações. Foi verificado que a maior produção de éster (50%) ocorreu em oito dias. Nas reações de transesterificação, as relações molares em que houve maior consumo do éster produzido foram 1:5 e 1:10, sendo obtidos 21,1% e 29,6% de residual de dihidrocafeato de octila, respectivamente em 24 h. Foi observado que em altas temperaturas e tempo superior a 26 h, houve o menor residual de dihidrocafeato de octila (18,2%). Foram identificados três diferentes compostos fenólicos, contendo em sua estrutura dihidrocafeato de octila e ácido caprílico.

Cultivo artesanal do cogumelo Shiitake: uma potencial atividade para agroecossistemas sustentáveis

Edible mushroom cultivation has been gaining ground in the agricultural environment throughout the country, creating a new product option in the food market. This activity is linked to cultural and artisanal management with environmentally sustainable principles and generates income for small farms. In this context, the present study evaluated the potential for artisanal cultivation of Shiitake as an activity for sustainable agroecosystems. Initially, the historic of implementation and evolution of artisanal cultivation of Shiitake mushroom on properties considered models in Pato Branco, Guarapuava and São José dos Pinhais (Paraná) and Frei Rogerio, (Santa Catarina) were carried out. Consequently, a comparative analysis between the cultivation systems of these properties and the use of small wooded areas and reforested areas was conducted. Aspects of production, income and pluralism of the farms, were also performed. At the end, the nutritional quality parameters of mushrooms produced in different properties were evaluated. The results show economic potential in Shiitake production. The activity also has potential for the sustainable exploitation of native forest and reforested areas, contributing to the optimal use of physical space small properties. In artisanal cultivation of Shiitake there is a systemic interaction verified by the use of wood from the same farm, assisting in the renewal of biomass of the agroecosystem. Finally, it was found that mushrooms produced on different substrates used in the studied properties have high nutritional quality. Shiitake samples exhibited high contents of protein, fiber, minerals and low fat content.

Produção de biogás a partir da co-digestão de resíduos da geração de energia

Aplicações de microalgas tem tornado esses micro-organismos importantes em pesquisas com fins tanto comerciais como energéticos. A biofixação de CO2 por microalgas é vista como uma forma economicamente viável e ambientalmente sustentável para mitigar as emissões de CO2 e geração de biomassa para obtenção de bioprodutos de alto valor agregado como os biocombustíveis. Na digestão anaeróbia da biomassa de microalgas a adição de um cosubstrato rico em carbono pode facilitar o processo de produção de biogás. O glicerol possui alta concentração de carbono orgânico e é solúvel em água. Neste sentido, a combinação de ambos os substratos pode solucionar um dos principais problemas para o processo de digestão, que reside no equilíbrio da razão (C/N). Co-digestão anaeróbia consiste na digestão anaeróbia de uma mistura de dois ou mais substratos com composições complementares. O objetivo do estudo foi avaliar a geração de biogás através da co-digestão anaeróbia de biomassa de Spirulina sp. LEB 18 e glicerol bruto. Para a realização do estudo foram construídos e operados sete biorreatores com volume útil de 1,5 L, alimentados com 5, 6, 10, 15 e 20 g.L -1 da mistura de biomassa de Spirulina e glicerol. A adição de diferentes quantidades de glicerol (5 e 10 g.L -1 ) foi utilizada como um suplemento na digestão anaeróbia em sistema de batelada. A razão C/N variou de 3,3×103 a 23,7. Os ensaios foram realizados a 35 °C, em reatores equipados com sistema de coleta de gás, alimentação e retirada do efluente líquido, operados em batelada sequencial. O efluente líquido dos reatores foi analisado quanto ao pH, nitrogênio amoniacal e alcalinidade. O volume de biogás produzido diariamente foi medido em gasômetro de frasco invertido. Em todos os ensaios, os valores médios de pH variaram de 7,0 a 7,3 e nitrogênio amoniacal de 62,02 a 1100,99 mg.L-1 . A alcalinidade do efluente variou entre 1133,37 e 3578,98 mg.L-1 CaCO3. Em todos os ensaios com adição de glicerol houve incremento na produção específica de biogás (0,16 – 0,24 d -1 ) quando comparado ao ensaio em que somente biomassa microalgal era alimentada no processo (0,03 L.d-1 ), demonstrando ser esta uma alternativa interessante para a produção de biocombustível e concomitante agregação de valor ao glicerol residual da produção de biodiesel.