Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Genesis and Emplacement of Carbonatites and Lamprophyres in the Svecofennian Domain

A small carbonatite dyke swarm has been identified at Naantali, southwest Finland. Several swarms of shoshonitic lamprophyres are also known along the Archean-Proterozoic boundary in eastern Finland and northwest Russia. These intrusions, along with the carbonatite intrusion at Halpanen, eastern Finland, represent a stage of widespread low-volume mantle-sourced alkaline magmatism in the Svecofennian Domain. Using trace element and isotope geochemistry coupled with precise geochronology from these rocks, a model is presented for the Proterozoic metasomatic evolution of the Fennoscandian subcontinental lithospheric mantle. At ~2.2-2.06 Ga, increased biological production in shallow seas linked to continental rifting, resulted in increased burial rates of organic carbon. Subduction between ~1.93-1.88 Ga returned organic carbon-enriched sediments of mixed Archean and Proterozoic provenance to the mantle. Dehydration reactions supplied water to the mantle wedge, driving arc volcanism, while mica, amphibole and carbonate were brought deeper into the mantle with the subducting slab. The cold subducted slab was heated conductively from the surrounding warm mantle, while pressures continued to gradually increase as a result of crustal thickening. The sediments began to melt in a two stage process, first producing a hydrous alkaline silicate melt, which infiltrated the mantle wedge and crystallised as metasomatic veins. At higher temperatures, carbonatite melt was produced, which preferentially infiltrated the pre-existing metasomatic vein network. At the onset of post-collisional extension, deep fault structures formed, providing conduits for mantle melts to reach the upper crust. Low-volume partial melting of the enriched mantle at depths of at least 110 km led to the formation of first carbonatitic magma and subsequently lamprophyric magma. Carbonatite was emplaced in the upper crust at Naantali at 1795.7 ± 6.8 Ma; lamprophyres along the Archean-Proterozoic boundary were emplaced between 1790.1 ± 3.3 Ma and 1781 ± 20 Ma.

Meio de cultura semi-seletivo para detecção de Curtobacterium flaccumfaciens pv. flaccumfaciens em solo e sementes de feijoeiro

A murcha-de-curtobacterium, causada pela bactéria Curtobacterium flaccumfaciens pv. flaccumfaciens (Cff), é um importante problema para o cultivo de feijão (Phaseolus vulgaris L.) na região Centro-Sul do Brasil. A principal forma de disseminação da bactéria é por sementes contaminadas. Embora a ocorrência desta doença seja relativamente recente no Brasil, Cff tem sido disseminado rapidamente nas regiões produtoras de feijão do país. Este trabalho teve como objetivo ajustar o meio de cultura CNS (Corynebacterium Nebraskense Selective Medium) para recuperação e detecção de Cff em solo e sementes de feijoeiro. Suspensões provenientes da lavagem de amostras de solo e sementes contaminadas pela bactéria foram plaqueadas no meio de cultura CNS - modificado. Os ajustes realizados no meio de cultura possibilitaram a recuperação eficiente de Cff presente em solo e sementes contaminadas. As modificações estabelecidas para o meio CNS foram a redução da concentração de sulfato de polimixina para 16 mg/l, exclusão do componente ciclohexamida e substituição do fungicida Daconil 2787-F (530 mg/ml de chlorothalonil) pelo Dacostar 500 (500 mg/ml de chlorothalonil).

Meio semi-seletivo para detectar Xanthomonas axonopodis pv. phaseoli em sementes de feijoeiro e sua erradicação através do tratamento de sementes com o fungicida tolylfluanid

Estudou-se a eficiência do meio semi-seletivo desenvolvido para Xanthomonas axonopodis pv. malvacearum (Xam) do algodoeiro, com algumas modificações, na detecção de Xanthomonas axonopodis pv. phaseoli (Xap) em sementes de feijoeiro, bem como a eficiência do fungicida tolylfluanid na erradicação de Xap através do tratamento de sementes. Foram utilizadas sementes naturalmente infectadas por Xap, procedentes de diferentes municípios do Estado do Paraná. Houve o desenvolvimento de colônias bacterianas ao redor das sementes infectadas sob meio semi-seletivo entre seis e 12 dias de incubação. A freqüência de recuperação de colônias da bactéria em relação ao meio Agar nutriente (AN) variou entre 30 a 112%. O crescimento de Xap foi inibido a concentrações entre 54 a 1500 ppm do fungicida tolylfluanid. A bactéria foi recuperada das sementes não tratadas em meio semi-seletivo, mas não das sementes tratadas em solução do fungicida tolylfluanid (1,20g/L água). Em casa de vegetação, das 400 sementes tratadas com tolylfluanid não foi produzida nenhuma planta com sintomas da doença até 30 dias após a semeadura, enquanto que 9,75% das sementes não tratadas apresentaram sintomas de Xap. Em um outro experimento, das 1200 sementes não tratadas um total de 7,08% e 11,67% das plantas mostraram-se com sintomas da doença, enquanto que das sementes tratadas 0,5% e 2,4% apresentaram sintomas, 26 e 46 dias após a semeadura, respectivamente.

Boundary identification in the domain of a parabolic partial differential equation

Bakgrunden och inspirationen till föreliggande studie är tidigare forskning i tillämpningar på randidentifiering i metallindustrin. Effektiv randidentifiering möjliggör mindre säkerhetsmarginaler och längre serviceintervall för apparaturen i industriella högtemperaturprocesser, utan ökad risk för materielhaverier. I idealfallet vore en metod för randidentifiering baserad på uppföljning av någon indirekt variabel som kan mätas rutinmässigt eller till en ringa kostnad. En dylik variabel för smältugnar är temperaturen i olika positioner i väggen. Denna kan utnyttjas som insignal till en randidentifieringsmetod för att övervaka ugnens väggtjocklek. Vi ger en bakgrund och motivering till valet av den geometriskt endimensionella dynamiska modellen för randidentifiering, som diskuteras i arbetets senare del, framom en flerdimensionell geometrisk beskrivning. I de aktuella industriella tillämpningarna är dynamiken samt fördelarna med en enkel modellstruktur viktigare än exakt geometrisk beskrivning. Lösningsmetoder för den s.k. sidledes värmeledningsekvationen har många saker gemensamt med randidentifiering. Därför studerar vi egenskaper hos lösningarna till denna ekvation, inverkan av mätfel och något som brukar kallas förorening av mätbrus, regularisering och allmännare följder av icke-välställdheten hos sidledes värmeledningsekvationen. Vi studerar en uppsättning av tre olika metoder för randidentifiering, av vilka de två första är utvecklade från en strikt matematisk och den tredje från en mera tillämpad utgångspunkt. Metoderna har olika egenskaper med specifika fördelar och nackdelar. De rent matematiskt baserade metoderna karakteriseras av god noggrannhet och låg numerisk kostnad, dock till priset av låg flexibilitet i formuleringen av den modellbeskrivande partiella differentialekvationen. Den tredje, mera tillämpade, metoden kännetecknas av en sämre noggrannhet förorsakad av en högre grad av icke-välställdhet hos den mera flexibla modellen. För denna gjordes även en ansats till feluppskattning, som senare kunde observeras överensstämma med praktiska beräkningar med metoden. Studien kan anses vara en god startpunkt och matematisk bas för utveckling av industriella tillämpningar av randidentifiering, speciellt mot hantering av olinjära och diskontinuerliga materialegenskaper och plötsliga förändringar orsakade av “nedfallande” väggmaterial. Med de behandlade metoderna förefaller det möjligt att uppnå en robust, snabb och tillräckligt noggrann metod av begränsad komplexitet för randidentifiering.

Towards input/output-free modelling of linear infinite-dimensional systems in continuous time

This dissertation describes a networking approach to infinite-dimensional systems theory, where there is a minimal distinction between inputs and outputs. We introduce and study two closely related classes of systems, namely the state/signal systems and the port-Hamiltonian systems, and describe how they relate to each other. Some basic theory for these two classes of systems and the interconnections of such systems is provided. The main emphasis lies on passive and conservative systems, and the theoretical concepts are illustrated using the example of a lossless transfer line. Much remains to be done in this field and we point to some directions for future studies as well.

Semi-selective medium for Fusarium graminearum detection in seed samples

Fungi of the genus Fusarium cause a variety of difficult to control diseases in different crops, including winter cereals and maize. Among the species of this genus Fusarium graminearum deserves attention. The aim of this work was to develop a semi-selective medium to study this fungus. In several experiments, substrates for fungal growth were tested, including fungicides and antibiotics such as iprodiona, nystatin and triadimenol, and the antibacterial agents streptomycin and neomycin sulfate. Five seed samples of wheat, barley, oat, black beans and soybeans for F. graminearum detection by using the media Nash and Snyder agar (NSA), Segalin & Reis agar (SRA) and one-quarter dextrose agar (1/4PDA; potato 50g; dextrose 5g and agar 20g), either unsupplemented or supplemented with various concentrations of the antimicrobial agents cited above. The selected components and concentrations (g.L-1) of the proposed medium, Segalin & Reis agar (SRA-FG), were: iprodiona 0.05; nystatin 0,025; triadimenol 0.015; neomycin sulfate 0.05; and streptomycin sulfate, 0.3 added of ¼ potato sucrose agar. In the isolation from seeds of cited plant species, the sensitivity of this medium was similar to that of NSA but with de advantage of maintaining the colony morphological aspects similar to those observed in potato-dextrose-agar medium.

Semi-selective culture medium for Exserohilum turcicum isolation from corn seeds

Northern corn leaf blight, caused by Exserohilum turcicum (Et), is a disease of widespread occurrence in regions where corn, sweetcorn and popcorn are grown. This disease has great potential to cause damage and has been studied for years, but the association of its causal agent with seeds remains unconfirmed. Thus, the availability of a sensitive method to detect and quantify the inoculum in seeds, even at low incidence, is essential. The aim of this study was to develop a method to detect and quantify the presence of the fungus infecting and infesting corn and popcorn seeds. Artificially and naturally infected seeds were employed to develop the medium. The semi-selective medium was composed of carbendazim (active ingredient) (60 mg/L), captan (30 mg/L), streptomycin sulfate (500 mg/L) and neomycin sulfate (600 mg/L) aggregated to the medium lactose casein hydrolysate agar medium. By using this, Et was detected in naturally infected corn seeds, showing 0.124% incidence, in four out of ten analyzed samples. In addition, 1.04 conidia were detected per infested seed. By means of isolation, pathogenicity test, morphological characterization and comparison with descriptions of the species in the literature, the fungus isolated from the seeds was confirmed to be Et. Both infection and infestation were considered low; thus, for studies of Et detection in corn seeds, the use of semi-selective medium and more than 1,200 seeds/sample is suggested.

Meios de cultura semi-seletivos para Macrophomina phaseolina

Macrophomina phaseolina (Tassi) Golidanich é um fungo habitante do solo importante economicamente devido ao amplo número de espécies de plantas que infectam e da dificuldade do seu controle. Vários estudos envolvendo densidade de inóculo, taxonomia, sobrevivência, necessitam de meios de cultura seletivo ou semi-seletivo. O objetivo do trabalho foi avaliar 16 meios de cultura quanto à especificidade a este patógeno, proporcionando maior porcentagem de detecção do seu crescimento e menor número de contaminações, para substituir o meio semi-seletivo RB modificado, rotineiramente utilizado em estudos deste patógeno. O meio semi-seletivo RB modificado é bastante eficiente e contém em sua composição o fungicida metalaxyl (inibidor de oomycetos), que atualmente não se encontra disponível comercialmente em formulação simples, sem adição do Mancozeb ou Clorotalonil que inibem o crescimento do fungo M. phaseolina. Os meios de cultura avaliados foram repicados com o inóculo do fungo produzido em substrato areno-orgânico, contido em bolsas de náilon, recuperados após 30 dias de um solo não autoclavado, contido em uma bandeja. Cada meio de cultura avaliado tiveram 7 repetições, representadas por uma placa de Petri. Para as comparações das médias das porcentagens do crescimento de M. phaseolina e do número de contaminantes foi utilizado o teste de Scott-knott a 5% de probabilidade e os valores em porcentagem foram transformados em arc sem (√/100). Dentre os meios de cultura avaliados os MSTP 1 [(BDA com tetraciclina 50 mg.L-1 mais propamocarb a 1 mL.L-1(Previcur N® 72,2% p.a.)], MSRP 0,5 (BDA com rifampicina 100 mg.L-1 mais fungicida propamocarb a 0,5 mL.L-1) e MSRP 1 (BDA com rifampicina 100 mg.L-1 mais fungicida propamocarb a 1 mL.L-1) proporcionaram maior porcentagem e detecção do fungo M. phaseolina e menor número de contaminações por outros fungos e bactérias. Estes meios de cultura semi-seletivos podem ser utilizados em futuros trabalhos visando estudos epidemiológicos e de medidas de controle do fungo M. phaseolina.

Biocontrol of Sclerotinia sclerotiorum and white mold of soybean using saprobic fungi from semi-arid areas of Northeastern Brazil

ABSTRACTThe incidence and the levels of yield loss caused by the white mold of soybean (caused by the fungus Sclerotinia sclerotiorum) have increased in areas of higher altitude at Cerrado and Southern Brazil, causing yield losses of up to 60%. The aim of this study was to select saprobic fungi with the potential to control the white mold of soybean. First, in vitroantagonism screening was carried out to test eight saprobic fungi against S. sclerotiorum. Assessment of S. sclerotiorum mycelial growth was done at four and seven days after its placement on the culture medium. The isolate showing greatest antagonistic effect in all tests/assessments was Myrothecium sp. An in vivo experiment was conducted in a greenhouse and growth chamber, where plants previously treated with eight saprobic fungi were artificially inoculated with S. sclerotiorum. The fungal culture medium (potato-dextrose) and the commercial resistance inducer acibenzolar-S-methyl were used as controls. In the in vivotests, severity of the white mold was assessed at 8, 14 and 21 days after inoculation. The highest reduction percentage in the lesion length was observed for the treatment with Myrothecium sp. (70%), which has the greater potential to be used as biocontrol agent of soybean under the conditions of this experiment.

Estrutura genética espacial de duas populações naturais de Myracrodruon urundeuva M. Allemão na região semi-árida, Brasil

Para determinar se a distribuição espacial dos genótipos é aleatória ou se está estruturada, utilizou-se a autocorrelação espacial dos genótipos para investigar dados alozímicos de duas populações naturais de Myracrodruon urundeuva do semi-árido brasileiro (Estação Ecológica do Seridó/RN, com 1.166,38/ha e Sítio Mata dos Alves/PB com 84/ha). A primeira população encontra-se em áreas mais preservadas, enquanto a segunda está em uma área fragmentada. O programa utilizado foi o "Autocorr". A autocorrelação estimada para os locos polimórficos foi realizada nos indivíduos adultos. Foram analisados dois alelos na Estação Ecológica do Seridó e quatro no Sítio Mata dos Alves. Utilizaram-se de três métodos para o pareamento de indivíduos a serem comparados: conexão de Gabriel (Ig), vizinho mais próximo (Ivmp) e comparações dentro de classes de distâncias preestabelecidas. Os resultados obtidos para Ig e Ivmp (Pgm-2: 0,032 e 0,236; Est-1: 0,263 e 0,242, respectivamente) na estação ecológica e Ig e Ivmp (Pgm-1: -0,349 e -0,288; Pgm-2: -0,341 e-0,278; Est-1: -0,349 e -0,284 e Mdh-1: -0,345 e 0,282, respectivamente) no sítio não mostraram a presença de estruturação genética espacial, o que possibilita pressupor que exista uma distribuição aleatória dos genótipos dentro delas. O mesmo foi detectado para as comparações dentro de classes de distâncias preestabelecidas. Os resultados mantiveram o mesmo padrão encontrado para algumas populações naturais de espécies arbóreas tropicais já estudadas.

Applications of graph transformation in tools for domain-specific modeling languages

The use of domain-specific languages (DSLs) has been proposed as an approach to cost-e ectively develop families of software systems in a restricted application domain. Domain-specific languages in combination with the accumulated knowledge and experience of previous implementations, can in turn be used to generate new applications with unique sets of requirements. For this reason, DSLs are considered to be an important approach for software reuse. However, the toolset supporting a particular domain-specific language is also domain-specific and is per definition not reusable. Therefore, creating and maintaining a DSL requires additional resources that could be even larger than the savings associated with using them. As a solution, di erent tool frameworks have been proposed to simplify and reduce the cost of developments of DSLs. Developers of tool support for DSLs need to instantiate, customize or configure the framework for a particular DSL. There are di erent approaches for this. An approach is to use an application programming interface (API) and to extend the basic framework using an imperative programming language. An example of a tools which is based on this approach is Eclipse GEF. Another approach is to configure the framework using declarative languages that are independent of the underlying framework implementation. We believe this second approach can bring important benefits as this brings focus to specifying what should the tool be like instead of writing a program specifying how the tool achieves this functionality. In this thesis we explore this second approach. We use graph transformation as the basic approach to customize a domain-specific modeling (DSM) tool framework. The contributions of this thesis includes a comparison of di erent approaches for defining, representing and interchanging software modeling languages and models and a tool architecture for an open domain-specific modeling framework that e ciently integrates several model transformation components and visual editors. We also present several specific algorithms and tool components for DSM framework. These include an approach for graph query based on region operators and the star operator and an approach for reconciling models and diagrams after executing model transformation programs. We exemplify our approach with two case studies MICAS and EFCO. In these studies we show how our experimental modeling tool framework has been used to define tool environments for domain-specific languages.

Chlorophyll fluorescence of tropical tree species in a semi-deciduous forest gap

The characterization of different ecological groups in a forest formation/succession is unclear. To better define the different successional classes, we have to consider ecophysiological aspects, such as the capacity to use or dissipate the light energy available. The main objective of this work was to assess the chlorophyll fluorescence emission of tropical tree species growing in a gap of a semi-deciduous forest. Three species of different ecological groups were selected: Croton floribundus Spreng. (pioneer, P), Astronium graveolens Jacq. (early secondary, Si), and Esenbeckia febrifuga A. Juss. (late secondary, St). The potential (Fv/Fm) and effective (deltaF/Fm') quantum efficiency of photosystem II, apparent electron transport rate (ETR), non-photochemical (qN) and photochemical (qP) quenching of fluorescence were evaluated, using a modulated fluorometer, between 7:30 and 11:00 h. Values of Fv/Fm remained constant in St, decreasing in P and Si after 9:30 h, indicating the occurrence of photoinhibition. Concerning the measurements taken under light conditions (deltaF/Fm', ETR, qP and qN), P and Si showed better photochemical performance, i.e., values of deltaF/Fm', ETR and qP were higher than St when light intensity was increased. Values of qN indicated that P and Si had an increasing tendency of dissipating the excess of energy absorbed by the leaf, whereas the opposite was found for St. The principal component analysis (PCA), considering all evaluated parameters, showed a clear distinction between St, P and Si, with P and Si being closer. The PCA results suggest that chlorophyll fluorescence may be a potential tool to differentiate tree species from distinct successional groups.

Resistência natural de nove madeiras do semi-árido brasileiro a fungos xilófagos em condições de laboratório

Objetivou-se avaliar a resistência natural de nove madeiras do semi-árido brasileiro a fungos xilófagos, em condições de laboratório. As madeiras estudadas foram a algaroba (Prosopis juliflora), o angico (Anadenanthera macrocarpa), a aroeira (Myracrodruon urundeuva), a braúna (Schinopsis brasiliensis), a cássia (Senna siamea), a craibeira (Tabebuia aurea), o cumaru (Amburana cearensis), o ipê (Tabebuia impetiginosa) e o pereiro (Aspidosperma pyrifolium). De cada espécie foram retirados corpos-de-prova de 2,54 x 2,00 x 1,00 cm, com a maior dimensão na direção das fibras, em quatro posições na direção medula-casca. As amostras foram submetidas, por 14 semanas, à ação dos fungos Postia placenta e Neolentinus lepideus. A resistência natural, com exceção da algaroba e do angico (P. placenta), da craibeira (N. lepideus) e da cássia (P. placenta e N. lepideus), foi afetada pela posição na direção medula-casca, sem estar relacionada à densidade das madeiras ensaiadas. A madeira de ipê e a madeira de cerne da aroeira e braúna foram as mais resistentes aos fungos testados. As diferenças entre a resistência natural, exceto para a aroeira e braúna, não estavam associadas à concentração de extrativos solúveis em água quente.

Resistência natural de nove madeiras do semi-árido brasileiro a fungos causadores da podridão-mole

O objetivo desta pesquisa foi avaliar a resistência de nove madeiras de ocorrência no semi-árido brasileiro a fungos de podridão-mole, em condições de laboratório. As madeiras estudadas foram algaroba (Prosopis juliflora), angico (Anadenanthera colubrina var. cebil), aroeira (Myracrodruon urundeuva), braúna (Schinopsis brasiliensis), cássia (Senna siamea), craibeira (Tabebuia aurea), cumaru (Amburana cearensis), pau-d'arco (Tabebuia impetiginosa) e pereiro (Aspidosperma pyrifolium). De cada espécie foram retirados corpos-de-prova de 3,0 x 1,5 x 0,5 cm, com a maior dimensão no sentido das fibras, em quatro posições na direção medula-casca do tronco. As amostras permaneceram por 120 dias sob a ação da microflora natural existente em solo orgânico. A resistência ao apodrecimento da aroeira, braúna e cássia não foi afetada pela posição na direção medula-casca, não esteve relacionada à densidade das madeiras ensaiadas. As madeiras de aroeira e braúna (cerne), pereiro e pau-d'arco apresentaram melhor desempenho. A resistência natural não esteve associada à concentração de extrativos solúveis em água quente.