Designing intrinsically photostable low band gap polymers:a smart tool combining EPR spectroscopy and DFT calculations

A rapid and efficient method to identify the weak points of the complex chemical structure of low band gap (LBG) polymers, designed for efficient solar cells, when submitted to light exposure is reported. This tool combines Electron Paramagnetic Resonance (EPR) using the 'spin trapping method' coupled with density functional theory modelling (DFT). First, the nature of the short life-time radicals formed during the early-stages of photo-degradation processes are determined by a spin-trapping technique. Two kinds of short life-time radical (R and R′O) are formed after 'short-duration' illumination in an inert atmosphere and in ambient air, respectively. Second, simulation allows the identification of the chemical structures of these radicals revealing the most probable photochemical process, namely homolytical scission between the Si atom of the conjugated skeleton and its pendent side-chains. Finally, DFT calculations confirm the homolytical cleavage observed by EPR, as well as the presence of a group that is highly susceptible to photooxidative attack. Therefore, the synergetic coupling of a spin trapping method with DFT calculations is shown to be a rapid and efficient method for providing unprecedented information on photochemical mechanisms. This approach will allow the design of LBG polymers without the need to trial the material within actual solar cell devices, an often long and costly screening procedure.

Étude paléopathologique préliminaire à travers l'analyse macroscopique et scanographique : exemple du cimetière St. Matthew, ville de Québec (1771-1860)

Sachant que plusieurs maladies entrainent des lésions qui ne sont pas toujours observables à l’oeil, cette étude préliminaire en paléopathologie humaine utilise une approche complémentaire issue de l’imagerie médicale, le ct-scan, afin de fournir des diagnostics plus précis. L’objectif est donc de tester ici l’efficacité et les limites de l’analyse scanographique durant l’analyse de spécimens archéologiques. Un échantillon de 55 individus a été sélectionné à partir de la collection ostéologique provenant du cimetière protestant St. Matthew (ville de Québec, 1771 – 1860). Une analyse macroscopique et scanographique complète a alors été effectuée sur chaque squelette. Les observations macroscopiques ont consisté à enregistrer une dizaine de critères standardisés par la littérature de référence en lien avec des manifestations anormales à la surface du squelette. Les ct-scans ont été réalisés à l’Institut National de la Recherche Scientifique de la Ville de Québec avec un tomodensitomètre Somatom de Siemens (définition AS+ 128). Les données scanographiques ont permis d’enregistrer une série de critères complémentaires sur la structure interne de l’os (amincissement/épaississement de la corticale, variation de densité, etc.) Selon la méthode du diagnostic différentiel, des hypothèses ou diagnostics ont été proposés. Ils sont principalement basés sur les critères diagnostiques mentionnés dans les manuels de référence en paléopathologie, mais aussi à l’aide de la littérature clinique et l’expertise de médecins. Les résultats présentés ici supportent que: 1) Dans 43% des cas, les données scanographiques ont apporté des informations essentielles dans la diagnose pathologique. Cette tendance se confirme en fonction de certaines maladies, mais pas d’autres, car certains diagnostics ne peuvent se faire sans la présence de tissus mous. 2) La distribution spatiale de la plupart des lésions varie selon les régions anatomiques, aussi bien en macroscopie qu’en scanographie. 3) Certains types de maladie semblent associés à l’âge et au sexe, ce qui est conforté par la littérature. 4) Cette recherche démontre aussi que le processus de diagnose nécessite, dans 38% des cas, une analyse complémentaire (ex. histologie, scintigraphie, radiographie) pour préciser le diagnostic final.

Produktutveckling av en provdocka för lekredskapsutveckling

Detta projekt beställdes av lekredskapstillverkaren HAGS i Aneby. De behövde en docka i en 4-årings storlek till sin produktutveckling. Det företaget frågar efter är en så antropomorfiskt korrekt docka som möjligt med framför allt korrekta proportioner på huvud och lemmar. Denna docka skulle användas för att fastställa måtten på nya produkter och för säkrare säkerhetstester. För att dockan skulle vara könsneutral så fick både dockan och projektet namnet KIM. Projektet har gått igenom flera faser. Först specificerades vad som skulle göras och vilka delar som var viktigast att fokusera på. Sedan löstes hur dockans alla leder skall fungera, hur ytan skall behandlas och hur allting skall monteras. Den huvudsakliga metoden för framtagandet av koncept och slutresultat har varit en iterativ process där lösningar har tagits fram, testats, ändrats och testats igen. Det som har framställts i projektet är koncept för ett helt skelett som med lättare modifieringar kan användas till flera applikationer. Delarna i skelettet är konstruerade efter en ”One Size Fits All” princip där ett litet antal delar kan användas till flera funktionsområden. En del arbete återstår, huvudet har inte fått sin slutgiltiga konstruktion och både händer och fötter behöver gå igenom ett par designfaser för att färdigställas. Det som framför allt återstår av projektet är tillverkning av alla delar, vilket innebär mycket arbete med en 3d-skrivare för alla leder och skulptering för hand för alla mjukdelar.

Développement des bétons autoplaçants à faible teneur en poudre, Éco-BAP: formulation et performance

Abstract : Although concrete is a relatively green material, the astronomical volume of concrete produced worldwide annually places the concrete construction sector among the noticeable contributors to the global warming. The most polluting constituent of concrete is cement due to its production process which releases, on average, 0.83 kg CO[subscript 2] per kg of cement. Self-consolidating concrete (SCC), a type of concrete that can fill in the formwork without external vibration, is a technology that can offer a solution to the sustainability issues of concrete industry. However, all of the workability requirements of SCC originate from a higher powder content (compared to conventional concrete) which can increase both the cost of construction and the environmental impact of SCC for some applications. Ecological SCC, Eco-SCC, is a recent development combing the advantages of SCC and a significantly lower powder content. The maximum powder content of this concrete, intended for building and commercial construction, is limited to 315 kg/m[superscript 3]. Nevertheless, designing Eco-SCC can be challenging since a delicate balance between different ingredients of this concrete is required to secure a satisfactory mixture. In this Ph.D. program, the principal objective is to develop a systematic design method to produce Eco-SCC. Since the particle lattice effect (PLE) is a key parameter to design stable Eco-SCC mixtures and is not well understood, in the first phase of this research, this phenomenon is studied. The focus in this phase is on the effect of particle-size distribution (PSD) on the PLE and stability of model mixtures as well as SCC. In the second phase, the design protocol is developed, and the properties of obtained Eco-SCC mixtures in both fresh and hardened states are evaluated. Since the assessment of robustness is crucial for successful production of concrete on large-scale, in the final phase of this work, the robustness of one the best-performing mixtures of Phase II is examined. It was found that increasing the volume fraction of a stable size-class results in an increase in the stability of that class, which in turn contributes to a higher PLE of the granular skeleton and better stability of the system. It was shown that a continuous PSD in which the volume fraction of each size class is larger than the consecutive coarser class can increase the PLE. Using such PSD was shown to allow for a substantial increase in the fluidity of SCC mixture without compromising the segregation resistance. An index to predict the segregation potential of a suspension of particles in a yield stress fluid was proposed. In the second phase of the dissertation, a five-step design method for Eco-SCC was established. The design protocol started with the determination of powder and water contents followed by the optimization of sand and coarse aggregate volume fractions according to an ideal PSD model (Funk and Dinger). The powder composition was optimized in the third step to minimize the water demand while securing adequate performance in the hardened state. The superplasticizer (SP) content of the mixtures was determined in next step. The last step dealt with the assessment of the global warming potential of the formulated Eco-SCC mixtures. The optimized Eco-SCC mixtures met all the requirements of self-consolidation in the fresh state. The 28-day compressive strength of such mixtures complied with the target range of 25 to 35 MPa. In addition, the mixtures showed sufficient performance in terms of drying shrinkage, electrical resistivity, and frost durability for the intended applications. The eco-performance of the developed mixtures was satisfactory as well. It was demonstrated in the last phase that the robustness of Eco-SCC is generally good with regards to water content variations and coarse aggregate characteristics alterations. Special attention must be paid to the dosage of SP during batching.

The dehydrogenation reactions between LiH and organic amines for solid state hydrogen storage systems

Hydrogen is considered as an appealing alternative to fossil fuels in the pursuit of sustainable, secure and prosperous growth in the UK and abroad. However there exists a persisting bottleneck in the effective storage of hydrogen for mobile applications in order to facilitate a wide implementation of hydrogen fuel cells in the fossil fuel dependent transportation industry. To address this issue, new means of solid state chemical hydrogen storage are proposed in this thesis. This involves the coupling of LiH with three different organic amines: melamine, urea and dicyandiamide. In principle, thermodynamically favourable hydrogen release from these systems proceeds via the deprotonation of the protic N-H moieties by the hydridic metal hydride. Simultaneously hydrogen kinetics is expected to be enhanced over heavier hydrides by incorporating lithium ions in the proposed binary hydrogen storage systems. Whilst the concept has been successfully demonstrated by the results obtained in this work, it was observed that optimising the ball milling conditions is central in promoting hydrogen desorption in the proposed systems. The theoretical amount of 6.97 wt% by dry mass of hydrogen was released when heating a ball milled mixture of LiH and melamine (6:1 stoichiometry) to 320 °C. It was observed that ball milling introduces a disruption in the intermolecular hydrogen bonding network that exists in pristine melamine. This effect extends to a molecular level electron redistribution observed as a function of shifting IR bands. It was postulated that stable phases form during the first stages of dehydrogenation which contain the triazine skeleton. Dehydrogenation of this system yields a solid product Li2NCN, which has been rehydrogenated back to melamine via hydrolysis under weak acidic conditions. On the other hand, the LiH and urea system (4:1 stoichiometry) desorbed approximately 5.8 wt% of hydrogen, from the theoretical capacity of 8.78 wt% (dry mass), by 270 °C accompanied by undesirable ammonia and trace amount of water release. The thermal dehydrogenation proceeds via the formation of Li(HN(CO)NH2) at 104.5 °C; which then decomposes to LiOCN and unidentified phases containing C-N moieties by 230 °C. The final products are Li2NCN and Li2O (270 °C) with LiCN and Li2CO3 also detected under certain conditions. It was observed that ball milling can effectively supress ammonia formation. Furthermore results obtained from energetic ball milling experiments have indicated that the barrier to full dehydrogenation between LiH and urea is principally kinetic. Finally the dehydrogenation reaction between LiH and dicyandiamide system (4:1 stoichiometry) occurs through two distinct pathways dependent on the ball milling conditions. When ball milled at 450 RPM for 1 h, dehydrogenation proceeds alongside dicyandiamide condensation by 400 °C whilst at a slower milling speed of 400 RPM for 6h, decomposition occurs via a rapid gas desorption (H2 and NH3) at 85 °C accompanied by sample foaming. The reactant dicyandiamide can be generated by hydrolysis using the product Li2NCN.

Seláceos do Farol das Lagostas (Bacia do Cuanza, Angola)

O presente trabalho consiste na apresentação da diversidade de seláceos do Farol das Lagostas pertencente à Bacia do Cuanza. Os condrichthyes são componentes comuns da fauna aquática desde o Paleozoico. No entanto, devido à natureza cartilaginosa do esqueleto, o registo paleontológico dos mesmos restringe-se, basicamente, às partes mineralizadas como dentes, dentículos dérmicos e espinhas cefálicas O lugar Farol das Lagostas contém uma fauna de seláceos relativamente rica e variada, representada neste estudo por cerca de 1.000 dentes isolados, além de outras peças esqueléticas. Foram identificados e descritos quarenta e quatro taxa, pertencentes às seguintes ordens: Hexanchiformes, Squaliformes, Pristiophoriformes, Squatiniformes, Lamniformes, Carcharhiniformes, Rajiformes e Myliobatiformes. Trata-se de uma diversidade faunística cuja maioria dos géneros possui representantes atuais. Os Carcharhiniformes representam 53% dos taxa identificados. Estão representadas as famílias Scyliorhinidae, Triakidae, Hemigaleidae, Carcharhinidae e Sphyrnidae, com 18 espécies. Verifica-se a presença de formas bentónicas e nectónicas que indicam condições térmicas moderadas, quentes e tropicais a temperadas, que habitam frequentemente zonas costeiras. A relação faunística identificada corresponde a uma zona litoral. Ora, considerando o conjunto de dados em face da presença de fauna pelágica e dos grandes predadores, especialmente Isurus hastalis e Carcharocles megalodon, podemos admitir que existisse então um Golfo relativamente largo de uma faixa Atlântica aberta (Antunes & Balbino, 2004); ABSTRACT: Selachians from Farol the Lagostas (Cuanza Basin, Angola) The present work consists of the presentation of diversity of selachians from Farol das Lagostas, which belongs to the Cuanza Basin. The condrichthyes are a part of aquatic fauna since the Paleozoic. However, due to the nature of the cartilaginous skeleton, the paleontological registration of the same ones is restricted to mineralized parts like teeth, dermal denticles and cephalic spines. The of formation, Farol das Lagostas has a fauna of selachian relatively rich and diverse, represented in this study for around 1.000 isolated teeth, and other skeletal parts. Forty four taxa were described and identified, belonging to the following orders: Hexanchiformes, Squaliformes, Pristiophoriformes, Squatiniformes, Lamniformes, Carcharhiniformes, Rajiformes e Myliobatiformes. It’s a faunal diversity whose most genera have current representatives. The Carcharhiniformes represente 53% of the identified taxa. The represented families are Scyliorhinidae, Triakidae, Hemigaleidae, Carcharhinidae e Sphyrnidae, with 18 species. There is presence of benthic and nektonic forms that indicate moderate thermal conditions, the temperate and tropical hot, often inhabit coastal areas. The identified faunal relation corresponds to a coastal zone. So, considering the data set, due to the presence of pelagic fauna and large predators, especially Isurus hastalis e Carcharocles megalodon, we can admit that then there was a relatively large Gulf of open Atlantic range (Antunes & Balbino, 2004).