Avaliação qualitativa e quantitativa na deposição de calda de pulverização em Commelina benghalensis

O objetivo deste estudo foi o de avaliar a quantidade e qualidade da deposição da calda de pulverização em plantas de Commelina benghalensis, considerando os volumes de aplicação, as pontas de pulverização e o ângulo dos bicos na barra de pulverização. Foram utilizadas cinco hastes de plantas por vaso. O delineamento experimental adotado foi o inteiramente casualizado, com 20 repetições. O experimento foi conduzido em casa de vegetação e a aplicação da calda foi efetuada após 40 dias do transplantio das hastes, quando estavam com 30 a 40 cm de comprimento. Os tratamentos foram constituídos por cinco pontas de pulverização (TX-VK 6, TX-VK 8, XR 11001 VS, XR 11002 VS e TJ60 11002 VS), sendo testadas com dois ângulos de aplicação (0º e +30º), exceto a TJ60 11002 VS, e todas com dois volumes de calda distintos (100 e 200 L ha-1). Foi utilizado como traçador o corante Azul Brilhante FDC-1 na concentração de 500 ppm, para determinar a deposição da calda de pulverização. Após a aplicação, 20 hastes no total foram imediatamente coletadas e, em seguida, lavadas em 100 mL de água destilada, para posterior quantificação do traçador em espectrofotômetro. Os dados foram transformados em valores de depósitos por grama de massa seca e ajustados à curva de regressão pelo modelo de Gompertz. Os resultados evidenciaram que, independentemente da ponta utilizada, o volume de 200 L ha-1 proporcionou os maiores depósitos médios e pontuais nas plantas. Quanto à uniformidade do depósito de calda sobre as plantas, a ponta XR 11001 VS no volume de 100 L ha-1 proporcionou a melhor uniformidade. Contudo, quando se utilizou o ângulo de +30º, ocorreram acréscimos dos depósitos ao se utilizar o volume de 100 L ha-1, e, nesse caso, houve melhor uniformidade para o volume de 200 L ha-1.

Fator de crescimento fibroblástico básico e seus receptores em relação à atividade proliferativa na placenta bubalina em diferentes fases da gestação

Estudou-se a distribuição espaço-temporal do fator de crescimento fibroblástico básico (bFGF), do receptor 1 do fator de crescimento fibroblástico (FGFR1) e do receptor 2 do fator de crescimento fibroblástico (FGFR2) na placenta bubalina, correlacionando-a à proliferação celular. Para a detecção do bFGF, FGFR1, FGFR2 e antígeno Ki-67, colheram-se 12 placentas de búfalas nos terços inicial, médio e final da gestação, em abatedouros, e realizaram-se testes de imunoistoquímica. Detectou-se e avaliou-se a expressão do bFGF, do FGFR1, do FGFR2 e do antígeno Ki-67 ao longo da gestação. No compartimento fetal da placenta, observaram-se correlações positivas entre a expressão do bFGF e Ki-67, entre FGFR1 e Ki-67 e entre FGFR2 com Ki-67 (r=0,313, 0,358 e 0,384, respectivamente). No epitélio e estroma maternos observaram-se altas correlações entre FGFR1 e Ki-67 (r=0,739 e r=0,511, respectivamente). Os resultados sugerem envolvimento do bFGF, FGFR1 e FGFR2 na proliferação do trofoblasto enquanto no compartimento materno da placenta bubalina apenas o FGFR1 atuaria como modulador dessa atividade.

Correlação entre métodos tradicionais e espectroscopia de ultra-som na determinação de características físico-químicas do leite

Compararam-se a espectroscopia de ultra-som (US) e os métodos tradicionais (MT) utilizados para a determinação de características físico-químicas do leite e estimaram-se as correlações entre esses métodos e suas acurácias. As características densidade, extrato seco desengordurado (ESD), teor de proteínas e teor de gordura foram determinadas em 65 amostras de leite cru por ambos os métodos. As densidades médias determinadas pelo US e pelos MT não diferiram entre si (P=0,14), e a correlação encontrada entre os dois métodos para a determinação da densidade não foi significativa (P= 0,08). Os teores médios de ESD, proteína e gordura encontrados pelo US e pelos MT foram diferentes (P=0,04, P<0,0001 e P<0,0001, respectivamente), as correlações entre os dois métodos utilizados para a análise dessas características foram positivas e significativas (r=0,0109, r=0,0007, r= <0,0001, respectivamente) e as acurácias dos métodos para essas determinações foram de 0,160, 0,062 e 0,145, respectivamente. Foi determinada a equação de regressão linear, que associa o teor de gordura obtido no método de espectroscopia de ultra-som ao do método butirométrico, que apresentou coeficiente de determinação de 0,5936.

Uso de dilatador temporário em papilas mamárias de vacas, submetidas a lesões experimentais

Trinta e duas papilas mamárias de vacas da raça Holandesa, em período seco, foram submetidas a telotomia lateral que produziu defeito linear na mucosa da parte papilar do seio lactífero (PPSL). Houve excisão de um retângulo de mucosa de tamanho padronizado que provocou um defeito retangular na mucosa do PPSL, oposto à telotomia. Todas as telotomias foram suturadas e, aleatoriamente, em 16 delas foram introduzidas sondas de Foley de 2,7mm de diâmetro, formando o grupo de papilas com dilatador. A distensão dos balonetes das sondas de Foley provocou a dilatação da PPSL o que forçou a manutenção das sondas, por sete dias, na papila mamária. As 16 papilas restantes formaram o grupo de papilas sem dilatador. Foram realizadas videoteloscopias antes (dia 0) e após as telotomias (dia 8, após a retirada das sondas de Foley e dia 15). As avaliações morfológica e histológica do processo de cicatrização dos defeitos lineares e retangulares evidenciaram que o uso de dilatador na PPSL auxiliou na orientação cicatricial, mantendo a patência do seio lactífero em um maior número de papilas, quando os dois grupos foram comparados. A dilatação da PPSL interferiu na cicatrização das telotomias, e provocou maior número de alterações no epitélio de revestimento do seio lactífero.

Consumo, desempenho e parâmetros econômicos de novilhos Nelore e F1 Brangus x Nelore terminados em pastagens, suplementados com mistura mineral e sal nitrogenado com uréia ou amiréia

Avaliou-se o efeito da suplementação protéica (40% PB) com amiréia ou uréia sobre o consumo de suplemento, desempenho e características econômicas de novilhos terminados em pastagens. Foram utilizados 120 novilhos com 19 meses de idade e 358kg, sendo 60 Nelore e 60 F1 Brangus x Nelore, divididos em três tratamentos com 20 animais, alojados em piquetes de Brachiaria brizantha cv. Marandu de 10 hectares cada, totalizando 120 hectares, sendo dois piquetes por grupo genético e tratamento, pastejados alternadamente a cada pesagem (42 dias). Os tratamentos consistiram em mistura mineral com amiréia-150S (AM), mistura mineral com uréia+milho+enxofre (UR) e mistura mineral (MM). As médias de consumo de suplemento dos animais F1 foram de 206,1; 145,9 e 73,1g/dia, e as dos animais Nelore, 236,0; 205,1 e 94,3g/dia para os tratamentos AM, UR e MM, respectivamente. Para os novilhos Nelore, houve efeito (P<0,05) do suplemento sobre o peso de abate (PA), sendo a média do tratamento UR, 518,85kg, mais alta que a dos demais, 491,89 e 485,20kg, respectivamente, para AM e MM. Para os novilhos F1, foi significativo o efeito da suplementação protéica (P<0,05), com médias de 515,90 e 520,15kg, respectivamente, para os tratamentos UR e AM. A suplementação protéica proporcionou bom desempenho em animais F1 durante períodos de abundância de forragem. O uso de uréia apresentou melhor viabilidade econômica.

Ventilação mandatória intermitente sincronizada versus ventilação com suporte pressórico e volume garantido em coelhos induzidos à hemorragia aguda

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Differentiation of Acidithiobacillus ferrooxidans and A-thiooxidans strains based on 16S-23S rDNA spacer polymorphism analysis

Restriction fragment length polymorphism (RFLP) and sequence analyses of the PCR-amplified 16S-23S rDNA intergenic spacer (ITS) were used for differentiating Acidithiobacillus thiooxidans strains from other related acidithiobacilli, including A. ferrooxidans and A. caldus. RFLP fingerprints obtained with AluI, DdeI, HaeIII, HinfI and MspI enabled the differentiation of all Acidithiobacillus reference strains into species groups. The A. thiooxidans strains investigated (metal mine isolates) yielded identical RFLP patterns to the A. thiooxidans type strain (ATCC 19377(T)), except for strain DAMS, which had a distinct pattern for all enzymes tested. Fourteen A. ferrooxidans mine strains were assigned to 3 RFLP groups, the majority of which were grouped with A. ferrooxidans ATCC 23270(T). The spacer region of one representative strain from each of the RFLP groups obtained was subjected to sequence analysis, in addition to eleven additional A. thiooxidans strains isolated from sediment and water samples, and A. caldus DSM 8584(T). The tRNA(IIe) and tRNA(Ala) genes, present in all strains analyzed, showed high sequence similarity. Phylogenetic analysis of the ITS sequences differentiated all three Acidithiobacillus species. Inter- and infraspecific genetic variations detected were mainly due to the size and sequence polymorphism of the ITS3 region. Mantel tests showed no significant correlation between ITS sequence similarity and the geographical origin of strains. The results showed that the 16S-23S rDNA spacer region is a useful target for the development of molecular-based methods aimed at the detection, rapid differentiation and identification of acidithiobacilli. (C) 2004 Elsevier SAS. All rights reserved.

Development and testing of anode-supported solid oxide fuel cells with slurry-coated electrolyte and cathode

A laboratory setup was designed and put into operation for the development of solid oxide fuel cells (SOFCs). The whole project consisted of the preparation of the component materials: anode, cathode and electrolyte, and the buildup of a hydrogen leaking-free sample chamber with platinum leads and current collectors for measuring the electrochemical properties of single SOFCs. Several anode-supported single SOFCs of the type (ZrO(2):Y(2)O(3)+NiO) thick anode/(ZrO(2):Y(2)O(3)) thin electrolyte/(La(0.65)Sr(0.35)MnO(3)+ZrO(2):Y(2)O(3)) thin cathode have been prepared and tested at 700 and 800 degrees C after in situ H(2) anode reduction. The main results show that the slurry-coating method resulted in single-cells with good reproducibility and reasonable performance, suggesting that this method can be considered for fabrication of SOFCs. (c) 2005 Elsevier B.V. All rights reserved.

Influence of different extraction methods on the yield and linalool content of the extracts of Eugenia uniflora L.

This work has been developed using a sylvestral fruit tree, native to the Brazilian forest, the Eugenia uniflora L., one of the Mirtaceae family. The main goal of the analytical study was focused on extraction methods themselves. The method development pointed to the Clevenger extraction as the best yield in relation to SFE and Soxhlet. The SFE method presented a good yield but showed a big amount of components in the final extract, demonstrating low selectivity. The essential oil extracted was analyzed by GC/FID showing a large range of polarity and boiling point compounds, where linalool, a widely used compound, was identified. Furthermore, an analytical solid phase extraction method was used to clean it up and obtain separated classes of compounds that were fractionated and studied by GC/FlD and GUMS. (c) 2006 Elsevier B.V. All rights reserved.

Effect of oxidizing and reducing atmospheres on the electrical properties of dense SnO2-based varistors

The SnO2 based varistor systems recently presented in the literature appear to have a promising potential in commercial applications. Experimental evidence shows that there is a dependence of nonlinear constant values with thermal treatment under different atmospheres. Thermal treatments in oxygen and nitrogen rich atmospheres at 900 degreesC prove this dependence, indicating that the nonlinear constant values are significantly lower when the material is submitted to a nitrogen atmosphere. Moreover, electrical properties can be restored when the varistor is subjected to thermal treatment at the same temperature in an oxygen atmosphere, indicating that the mechanism seems to be reversible. This paper discusses this behavior focusing in the grain boundary region. Ta2O5 mol% concentrations are also analyzed and the results indicate an optimum Ta2O5 concentration of 0.05 mol% for the electrical properties (alpha = 44 and E-B = 6150 V cm(-1)). (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Effect of tillage on fractal indices describing soil surface microrelief of a Brazilian Alfisol

Soil surface roughness is known to influence water infiltration, runoff and erosion. Soil surface roughness changes with management and weather and its mathematical description still remains an important issue. The main objective of this study was to investigate the effect of tillage on the two fractal indices, fractal dimension, D, and crossover length, 1, currently used in characterizing soil surface microrelief. The statistical index random roughness, RR, was also assessed. Field experiments were done on an Alfisol located at Rio Grande do Sul State (Brazil). Two tillage treatments (conventional versus direct drilling) were tested. The soil surface microrelief was assessed by point elevation measurements in 16 plots for each treatment. The sampling scheme was a square grid with 20 x 20 mm between point spacing and the plot size was 280 x 280 mm, so that each data set consisted of 225 individual elevation points. All indices were calculated after trend removal, both by slope correction, i.e., oriented microrelief, and by slope plus tillage marks correction, i.e., random microrelief. The implemented algorithm for estimating D and 1 consisted in evaluating the roughness around the local root mean square deviation (RMS) of the point elevation values. Irrespective of tillage treatment and detrending procedure, fractal behavior extended only over a bounded range of scales, from 40 to 100 mm, due to the experimental setup. In these conditions, assessing fractal indices was not always straightforward. The statistical index RR and the fractal index I were significantly different between tillage treatments for oriented and random surface conditions. D values of random soil surfaces were not affected by tillage treatment, whereas D values of oriented microrelief were significantly lower in the direct drilled plots. Removal of tillage marks trend resulted in a significant increase in D values. Within each tillage treatment, 1 and D were significantly correlated. (c) 2006 Elsevier B.V. All rights reserved.

Grazing incidence X-ray diffraction and atomic force microscopy analysis of BaBi2Ta2O9 thin films

Thin films of BaBi2Ta2O9 (BBT) composition were prepared through the metal organic decomposition method. The crystallinity, phase formation, crystallite size and morphology of the thin films were measured as a function of the type of substrate, stoichiometry of solution and process variables such as thickness and temperature. The thin films were investigated by grazing incidence X-ray diffractometry and atomic force microscopy (AFM) techniques. For the sample without excess of bismuth, diffraction peaks other than that of the BBT phase were observed. A well crystallized BBT single phase was observed for films prepared from a solution with 10% excess of bismuth, deposited on Si/Pt substrate, with a thickness up to 150 nm and sintered at temperatures of 700 degreesC. The thin BBT phase films heat-treated at 600 degreesC presented a diffraction pattern characteristic of samples with lower degree of crystallinity whereas for the thin films heat-treated at 800 degreesC, we observed the presence of other phases than the BBT. For the thin film deposited on the Sin+ substrate, we observe that the peaks corresponding to the BBT phase are broader than that observed on the samples deposited on the Pt and Si/Pt substrates. No variation of average crystallite size was observed as the excess of Bi increased from 10 to 20%. AFM images for the samples showed that the increasing the amount of bismuth promotes grain growth. The average surface roughness measured was in the range of 16-22 nm showing that the bismuth amount had no or little effect on the roughness of films. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Strategies of karyotype differentiation in Elateridae (Coleoptera, Polyphaga)

The chromosome study of five species of the family Elateridae, belonging to the subfamilies Agrypninae and Elaterinae, and the analysis of the cytogenetic data previously recorded for this family permitted the establishment of the main strategies of karyotypic differentiation that has occurred in the elaterids. In Agrypninae, the three species studied (Conoderus fuscofasciatus, Conoderus rufidens, and Conoderus sp.) showed the male karyotype 2n = 16 + X0. This karyotypic uniformity detected in these Conoderus species has also been shared with other species of the same genus, differing considerably from chromosomal heterogeneity verified in the subfamily Agrypninae. The use of the C-banding technique in C. fuscofasciatus and Conoderus sp. revealed constitutive heterochromatin in the pericentromeric region of the majority of the chromosomes. In C. fuscofasciatus, additional constitutive heterochromatin were also observed in the long arm terminal region of almost all chromosomes. Among the representatives of Elaterinae, the karyotype 2n = 18 + Xy(p) of Pomachilius sp.2 was similar to that verified in the majority of the Coleoptera species, contrasting with the chromosomal formula 2n = 18 + X0 detected in Cardiorhinus rufilateris, which is most common in the species of Elaterinae. In the majority of the elaterids, the chromosomal differentiation has frequently been driven by reduction of the diploid number; but, among the four cytogenetically examined subfamilies, there are some differences in relation to the trends of karyotypic evolution. (C) 2006 Elsevier Ltd. All rights reserved.

The influence of internal surface treatments on tensile bond strength for two ceramic systems

Statement of the Problem: the ceramic composition and surface microstructure of all-ceramic restorations are important components of an effective bonding substrate. Hydrofluoric acid and sandblasting are well-known procedures for surface treatment; however, surface treatment for high alumina-containing and lithium disilicate ceramics have not been fully investigated.Purpose: This in vitro study evaluated the tensile bond strength of resin cement to two types of ceramic systems with different surface treatments.Methods and Materials: Thirty specimens of each ceramic system were made according to the manufacturer's instructions and embedded in polyester resin. Specimens of In-Ceram Alumina [1] and IPS Empress 2 [E] were distributed to three groups with differing surface treatments (n=10): sandblasting with 50 jam aluminum oxide (APA); sandblasting with 110 pm aluminum oxide modified with silica particles (ROCATEC System-RS); a combination of sandblasting with APA and 10% hydrofluoric acid etching (HA) for two minutes on In-Ceram and for 20 seconds for IPS Empress 2. After the respective surface treatments, all the specimens were silanated, and Rely-X resin cement was injected onto the ceramic surface and light polymerized. The specimens were stored in distilled water at 37 degrees C for 24 hours and thermally cycled 1,100 times (5 degrees C/55 degrees C). The tensile bond strength test was performed in a universal testing machine at a 0.5 mm/minute crosshead speed.Results: the mean bond strength values (AWa) for IPS Empress 2 were 12.01 +/- 5.93 (EAPA), 10.34 +/- 1.77 (ERS) and 14.49 +/- 3.04 (EHA). The mean bond strength values for In-Ceram Alumina were 9.87 +/- 2.40 JAPA) and 20.40 +/- 6.27 (IRS). All In-Ceram specimens treated with 10% hydrofluoric acid failed during thermal cycling.Conclusion: the Rocatec system was the most effective surface treatment for In-Ceram Alumina ceramics; whereas, the combination of aluminum oxide sandblasting and hydrofluoric acid etching for 20 seconds worked more effectively for Empress 2 ceramics.