Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Brazilian cerrado antioxidant sources: cytotoxicity and phototoxicity in vitro

Annona crassiflora (araticum), Eugenia dysenterica (cagaita), and Caryocar brasiliense (pequi) are tropical fruits of the second biggest Brazilian biome: the cerrado. Nowadays, the cerrado faces two different realities: 1) the great possibility of food production since it is considered as the biggest storehouse of the world; and 2) the rich biodiversity that has been newly discovered and known. Previous studies showed that certain cerrado fruits demonstrate high content of total phenols and excellent antioxidant activity in in vitro models. Moreover, using fingerprinting analysis, important bioactive molecules were identified as probably responsible for their antioxidant activity. In this study, the cytotoxicity and phototocixity of ethanolic extracts from cerrado fruits were evaluated using the in vitro Neutral Red Uptake (NRU). Regarding cytotoxicity, the extracts of araticum peel and cagaita seed did not shown any cytotoxic potential up to 300 µg.mL-1. Ethanolic extracts of araticum seed and pequi peel presented low cytotoxic potential and, according to linear regressions, the estimated LD50 were de 831.6 and 2840.7 mg.kg-1, respectively. In the evaluated conditions, only the araticum peel extract presented a phototoxic potential. This is the first attempt to screen the toxicity of cerrado fruits with high antioxidant activity.

Application of Response Surface Methodology to study the effect of different calcium sources in fish muscle-alginate restructured products

Sodium alginate needs the presence of calcium ions to gelify. For this reason, the contribution of the calcium source in a fish muscle mince added by sodium alginate, makes gelification possible, resulting a restructured fish product. The three different calcium sources considered were: Calcium Chloride (CC); Calcium Caseinate (CCa); and Calcium lactate (CLa). Several physical properties were analyzed, including mechanical properties, colour and cooking loss. Response Surface Methodology (RSM) was used to determine the contribution of different calcium sources to a restructured fish muscle. The calcium source that modifies the system the most is CC. A combination of CC and sodium alginate weakened mechanical properties as reflected in the negative linear contribution of sodium alginate. Moreover, CC by itself increased lightness and cooking loss. The mechanical properties of restructured fish muscle elaborated were enhanced by using CCa and sodium alginate, as reflected in the negative linear contribution of sodium alginate. Also, CCa increased cooking loss. The role of CLa combined with sodium alginate was not so pronounced in the system discussed here.

Characterization of new sources of derivative starches as wall materials of essential oil by spray drying

Starch derivatives of taro (Colocasia esculenta L. Schott) and rice were characterized as wall materials of orange oil (d-limonene) by spray drying. Native starches were initially hydrolyzed with HCl and then esterified. Succinylated starches were modified using a conventional method in a slurry and were extruded; whereas, the phosphorylated starches were modified using the extrusion process. Viscosity and solubility of starches reduced after acid hydrolysis, derivatization, and extrusion. The particle size of the wall materials ranged between 20.05 and 31.81 µm. The encapsulation efficiency of the phosphorylated taro, rice, and waxy corn starches was 96.9, 96.8 and 97.1% respectively, and 98.6, 98.1, and 98.8% for succynilated taro, rice, and waxy corn starches, respectively. Starch derivatives of taro and rice could potentially be used as wall materials of orange oil d-limonene.

Effect of different calcium sources on the antioxidant stability of tortilla chips from extruded and nixtamalized blue corn (Zea mays L.) flours

This research aimed to develop tortilla chips (TC) high in antioxidants from extruded and nixtamalized blue corn flours prepared with calcium hydroxide Ca(OH)2 and calcium lactate C6H10O6Ca. Tortilla chips were made with extruded flours [0.1% Ca(OH)2; 0.9% C6H10O6Ca; without calcium] and nixtamalized flours [1% Ca(OH)2; 2.95% C6H10O6Ca] using the frying process. Total anthocyanin, total phenolics content, antioxidant activity, color, texture, and oil content were determined. The color of tortilla chips from extruded flours (TCEF) showed high values of the parameters a* and b* indicating a reduction in the blue color. These color parameters were significantly different from those observed in tortilla chips from nixtamalized flours (TCNF), which tended to be more blue. The TCEF retained 15% anthocyanins, 34% phenolics, and 54% antioxidant activity. Pearson's correlation analysis indicated that anthocyanins and phenolics correlated significantly with antioxidant activity and color. TCEF with both calcium sources showed higher fracturability compared with that of TCNF. Oil absorption showed an opposite effect, with lower oil content in TCEF. Nixtamalization and extrusion with C6H10O6Ca resulted in flours and TC high in anthocyanins and antioxidant activity, representing an alternative production process for corn snack high in antioxidants.

Main food sources of carotenoids, according to the purpose and degree of processing, for beneficiaries of the 'Bolsa Família' in Brazil

The intake of carotenoids is associated with antioxidant properties and some of these substances have activity of pro-vitamin A. This study aimed to estimate the intake of carotenoids (average values) by the Brazilian population focusing on beneficiaries of the 'Bolsa Família' Program and identify the dietary sources, according to the purpose and degree of processing and the inclusion of food additives. The database used is the personal food consumption module of the Household Budget Survey of 2008-2009, conducted by the Brazilian Institute of Geography and Statistics. The content of carotenoids in foods was obtained primarily from a National data source. Food products were classified into three categories: 1) fresh and minimally processed foods; 2) processed foods (containing food additives, except for flavoring and coloring agents); and 3) highly processed foods (containing flavoring and coloring agents). Insufficient intakes were identified for the conditional cash transfer program beneficiaries (3,547.1 µg). Fresh and minimally processed foods supplied between 48.6% (for girls) and 65.7% (for male adults) of pro-vitamin carotenoids. Processed foods were sources of between 55.5% and 57.0% of lutein + zeaxanthin for elderly and between 58.0% and 67.8% of lycopene for adults. Highly processed foods contributed to less than 5.0% of total carotenoids.

Physicochemical properties, modifications and applications of starches from different botanical sources

Present trends towards technologies and processes that increase the use of residues make starchy vegetal biomass an important alternative material in various applications due to starch’s versatility, low cost and ease of use when its physicochemical properties are altered. Starch is increasingly used in many industrial applications and as a renewable energy resource. Starch can be modified to enhance its positive attributes and eliminate deficiencies in its native characteristics. In this article, the state of knowledge on conventional and unconventional starches and their properties, characteristics, modifications and applications are reviewed.

Physiological quality of soybean and wheat seeds produced with alternative potassium sources

The use of unconventional sources of K for plants has been widely studied, but the effects of alternative materials on physiological seed quality are still relatively unknown. The objective of this study was to evaluate the physiological quality of soybean and wheat seeds after using different potassium sources in a crop succession. The experimental design was a completely randomized block with four replications. Treatments consisted of three K sources (KCl, alkaline rock and ground phonolite, with 58%, 11% and 8.42% of K2O, respectively) applied in four doses (0, 25, 50 and 100 kg K2O ha-1). Potassium doses were applied in soybean and their residual effects were evaluated on the following wheat crop. Soybean and wheat seeds were evaluated immediately after harvesting by tests for moisture content, seed weight, germination, first count, electrical conductivity, seedling length and seedling dry matter. Soybean plants fertilized with alternative sources of K produced heavier seeds with a lower coat permeability compared to KCl; the physiological quality of soybean seeds and the weight of wheat seeds increase due to higher K2O doses, independently of their source.

Physiological quality of coffee seeds produced under different levels of solar radiation and maturation stages

In Brazil, although the coffee plantations are predominantly grown under full sunlight, the use of agroforestry systems can lead to socioeconomic advantages, thus providing a favorable environment to the crop by promoting its sustainability as well as environmental preservation. However, there is a lack of information on physiological quality of the coffee seeds produced under different levels of solar radiation. Within this context, the objective of this study was to evaluate the influence of different levels of solar radiation and maturation stages on the physiological quality of coffee (Coffea arabica L.) seeds, cv. Acaiá Cerrado MG-1474. Three levels of solar radiation (plants grown under full sunlight; under plastic screens of 35% shading; and under plastic screens of 50% shading) and three maturation stages (cherry, greenish-yellow and green) were assessed. Physiological quality of seeds was assessed by using germination test, first count of germination, abnormal seedlings, dead seeds, and seedlings with open cotyledonary leaves. Electrophoretic analysis of isoenzymes catalase, esterase, superoxide dismutase and peroxidase was also performed. With the evolution of development the coffee seeds presents increases on physiological quality, and at its beginning the seeds show improvements on quality with the reduction of solar radiation.

La lettre et la carte de Toscanelli sur la route des Indes par l'Ouest, adressées en 1474 au Portugais Fernam Martins et transmises plus tard à Christophe Colomb : étude critique sur l'authenticité et la valeur de ces documents et sur les sources des idées cosmographiques de Colomb, suivie des divers textes de la lettre de 1474 / trad., annot. et fac-sim., par Henry Vignaud,...

Collection : Recueil de voyages et de documents pour servir à l'histoire de la géographie depuis le XIIIe jusqu'à la fin du XVIe siècle ; 18

1er mai 1920 à Paris, [des policiers molestent des manifestants devant le café Aux sources, à l'angle du boulevard de Magenta et de la rue Beaurepaire] : [photographie de presse] / [Agence Rol]

Référence bibliographique : Rol, 59135

[1er mai 1920 à Paris, des policiers molestent des manifestants devant le café Aux sources, à l'angle du boulevard de Magenta et de la rue Beaurepaire] : [photographie de presse] / [Agence Rol]

Référence bibliographique : Rol, 59137 bis