Mineralogy and major-element chemistry of volcanic ash of ODP Site 131-808

Mineralogical and major-element compositions of 72 samples of volcanic ash, recovered from Site 808 at Nankai Trough during Leg 131, were analyzed in relation to the early diagenetic alteration. Alteration products are first observed at the following depths: smectite, 200 mbsf; clinoptilolite, 646 mbsf; and analcite, 810 mbsf. Glass decomposition dominates over authigenic mineral formation between 200 and 550 mbsf in the sediment column, whereas mineral formation becomes dominant below 550 mbsf. Based on the X-ray diffraction patterns, a broad and asymmetric peak of 15A suggests a presence of illite/smectite (I/S) mixed-layered minerals in a sample from 646 mbsf. I/S mixed-layered mineral formation, however, rarely occurs even at the bottom of the sediment column (1290 mbsf) at 120° C. This is possibly because zeolite (especially clinoptilolite) formed in the ash interferes with illite formation in the smectite. The formation of alteration minerals affects the major-element chemistry of the ash and the interstitial waters. H4SiO4 concentrations in interstitial waters increase during glass decomposition and decrease with smectite and clinoptilolite formation. K is removed from interstitial water into smectite and/or clinoptilolite. Mg is fixed into smectite (and/or chlorite).

Composite depth scales, ash layer correlations and splice tie points of ODP Site 186-1151

We present composite depth scales for the multiply cored intervals from Sites 1150 and 1151. These new depth scales place coeval strata recovered in cores from different holes at a single site into a common stratigraphic framework. At Site 1150, double coring between Holes 1150A and 1150B occurred over only a short interval between ~703 and 713 meters below seafloor (mbsf), but this is sufficient to tie the upper portion of the stratigraphic section cored in Hole 1150A to the lower portion cored in Hole 1150B. The upper ~100 m of the sedimentary section at Site 1151 was double cored with the advanced piston corer and partially cored with the rotary core barrel, resulting in the complete recovery of this interval. The composite depth scales were constructed using Splicer software to vertically adjust the relative depths of various cores from one hole to the depths from another hole so as to align distinct physical properties measured on cores. The magnetic susceptibility data was the physical property most easily correlated between holes, and therefore primarily used to create a composite depth scale and spliced stratigraphic section. The spliced section is a continuous stratigraphic section constructed from representative cored intervals from the holes at a site. Both the splice and the composite depth scale can be applied to other data sets from Site 1151 to provide a stratigraphically continuous and laterally consistent basis for interpreting lithologic features or data sets. The resulting composite scale showed a 30% improvement in correlation of the magnetic susceptibility data relative to the original mbsf depth scale, and comparable improvement when applied to the other data sets.

Composition of bentonite-, smectite-rich- and ash beds from DSDP Leg 19 holes

Late Cenozoic ash deposits cored in Deep Sea Drilling Project Leg 19 in the far northwest Pacific and in the Bering Sea have altered to bentonite beds. Some bentonite layers were subsequently replaced by carbonate beds. A significant part of the Neogene volcanic history of land areas adjacent to the far north Pacific is represented by these diagenetic deposits. Bentonite beds are composed of authigenic smectite and minor amounts of clinoptilolite. Authigenic smectite has fewer illite layers than detrital smectite. Opal-A and opal-CT, abundant in Bering Sea sediment, are not found in ash or bentonite layers. The percentage of smectite in the total clay-mineral assemblage of ash beds is greater than that for adjacent terrigenous sediment, but the total amount of clay minerals in ash sequences is less than in surrounding deposits. Morphology of the 17-Å peak of smectite found in ash may represent newly formed, poorly crystalline smectite. Smectite becomes better crystallized as bentonite layers form. The percentage of smectite of the total clay-mineral assemblage in bentonite beds is greater than that in surrounding sediment, and, in contrast to ash beds, the total amount of clay minerals (mostly smectite) in bentonite layers is greater than in adjacent terrigenous sediment. Apparently, silica is not mobilized when volcanic ash layers transform to bentonite beds. Saponite-nontronite varieties of smectite and high Fe/Al and Ti/Al ratios distinguish bentonite beds derived from basaltic parent material from those beds formed from more silicic volcanic ash. These silicic ash beds produce bentonite composed mostly of montmorillonite. The basal sediment section at site 192 is rich with bentonite beds. Smectite in the upper part of this section (Eocene) was formed by low-temperature diagenesis of volcanic debris of intermediate or more silicic composition derived from arc or Pacific volcanoes. In contrast, smectite from the lowest 10 to 20 m of the sedimentary section (Cretaceous) is formed from either low-temperature or hydrothermal alteration of the underlying basaltic basement and associated pyroclastic debris. This near-basement smectite contains Mg and K acquired from sea water and Si, Al, Fe, Ti, and Mn released from the volcanic material.