Two-phase flow measurements with spacer grid in a rod bundle geometry

Heat transfer effectiveness in nuclear rod bundles is of great importance to nuclear reactor safety and economics. An important design parameter is the Critical Heat Flux (CHF), which limits the transferred heat from the fuel to the coolant. The CHF is determined by flow behaviour, especially the turbulence created inside the fuel rod bundle. Adiabatic experiments can be used to characterize the flow behaviour separately from the heat transfer phenomena in diabatic flow. To enhance the turbulence, mixing vanes are attached to spacer grids, which hold the rods in place. The vanes either make the flow swirl around a single sub-channel or induce cross-mixing between adjacent sub-channels. In adiabatic two-phase conditions an important phenomenon that can be investigated is the effect of the spacer on canceling the lift force, which collects the small bubbles to the rod surfaces leading to decreased CHF in diabatic conditions and thus limits the reactor power. Computational Fluid Dynamics (CFD) can be used to simulate the flow numerically and to test how different spacer configurations affect the flow. Experimental data is needed to validate and verify the used CFD models. Especially the modeling of turbulence is challenging even for single-phase flow inside the complex sub-channel geometry. In two-phase flow other factors such as bubble dynamics further complicate the modeling. To investigate the spacer grid effect on two-phase flow, and to provide further experimental data for CFD validation, a series of experiments was run on an adiabatic sub-channel flow loop using a duct-type spacer grid with different configurations. Utilizing the wire-mesh sensor technology, the facility gives high resolution experimental data in both time and space. The experimental results indicate that the duct-type spacer grid is less effective in canceling the lift force effect than the egg-crate type spacer tested earlier.

Cross-transmission of vancomycin-resistant Enterococcus in patients undergoing dialysis and kidney transplant

The objective of this study was to investigate the occurrence of vancomycin-resistant Enterococcus (VRE) cross-transmission between two patient groups (long-term dialysis and kidney transplant patients). Molecular typing, by automated ribotyping with the RiboPrinter Microbial Characterization System (Qualicon, USA), was used to analyze VRE isolates from 31 fecal samples of 320 dialysis patients and 38 fecal samples of 280 kidney transplant patients. Clonal spread of E. faecalis and E. casseliflavus was observed intragroup, but not between the two groups of patients. In turn, transmission of E. gallinarum and E. faecium between the groups was suggested by the finding of vancomycin-resistant isolates belonging to the same ribogroup in both dialysis and transplant patients. The fact that these patients were colonized by VRE from the same ribogroup in the same health care facility provides evidence for cross-transmission and supports the adoption of stringent infection control measures to prevent dissemination of these bacteria.

Arctic Offshore Management - uusi liiketoimintakonsepti offshoreteollisuudelle

Aker Arctic Technology Inc. (AACR) on kansainvälisesti tunnettu jäänmurtajien ja muiden arktisten alueiden laivojen suunnitteluun ja tekniseen konsultointiin erikoistuneena yhtiönä. Työn tavoitteena on luoda uusi arktisille alueille suunnattu liiketoimintakonsepti, jossa liiketoimintamallia kehitetään asiakastarpeen mukaan vastaamaan ja luomaan kysyntää palvelulle. Fyysisen kehitystyön tuloksena voidaan tarjota globaalisti ainutlaatuista teknistä testaustoimintaa ja säilytetään mallikoelaitoksen etumatka kilpailijoihin rakenteiden, tasanteiden ja alusten jäissä toimivuuden osalta. Tämän diplomityön teoreettisessa osuudessa kuvataan uusien ja jo olemassa olevien liiketoimintamallien kehittämiseen tarvittavaa johdon strategista välinettä Business Model Canvasia (BMC) ja muita analyysityökaluja. Työn teoreettisessa osuudessa käytettiin tieteellistä kirjallista aineistoa, julkaisuja sekä koti- että ulkomailta. Työn tutkimuksellisessa osuudessa havainnoitiin kuuden kuukauden ajan yrityksen sisällä toiminnassa tapahtuvaa liiketoimintaa. Havainnoinnin kautta kerättiin analyysien tiedot, joiden perusteella yhdessä yrityksen edustajien kanssa saatiin aikaan BMC. Uusi liiketoimintakonseptin todettiin olevan tarpeellinen arktisten offshore-palveluiden lisääntyvässä tarpeessa. Konseptin myötä saadaan nykyinen yrityksen palveluiden kompleksisuus pois ja samalla kyetään aggressiivisemmin markkinoimaan uusia tuotteita asiakkaille. Konseptin suurimpana vahvuutena on omat mallinnustilat, jonka monikäyttöisyys antaa liiketoiminnalle tarvittavan kilpailuedun.

Economics of Power-to-Gas integration to wastewater treatment plant

Solar and wind power produce electricity irregularly. This irregular power production is problematic and therefore production can exceed the need. Thus sufficient energy storage solutions are needed. Currently there are some storages, such as flywheel, but they are quite short-term. Power-to-Gas (P2G) offers a solution to store energy as a synthetic natural gas. It also improves nation’s energy self-sufficiency. Power-to-Gas can be integrated to an industrial or a municipal facility to reduce production costs. In this master’s thesis the integration of Power-to-Gas technologies to wastewater treatment as a part of the VTT’s Neo-Carbon Energy project is studied. Power-to-Gas produces synthetic methane (SNG) from water and carbon dioxide with electricity. This SNG can be considered as stored energy. Basic wastewater treatment technologies and the production of biogas in the treatment plant are studied. The utilisation of biogas and SNG in heat and power production and in transportation is also studied. The integration of the P2G to wastewater treatment plant (WWTP) is examined mainly from economic view. First the mass flows of flowing materials are calculated and after that the economic impact based on the mass flows. The economic efficiency is evaluated with Net Present Value method. In this thesis it is also studied the overall profitability of the integration and the key economic factors.

Water chemistry management for future large experimental facilities

The thesis focuses on the water chemistry of the experimental test facilities and their reference VVER reactors. The main objective of the thesis is to provide recommendations for water chemistry management for laboratory facilities (VEERA, PACTEL) simulating the VVERs and for the large future facilities of the Lappeenranta University of Technology. In the beginning, the concept of nuclear power generation and the applicability of the nuclear power usage is discussed. Next, different water chemistry and water purification systems in primary and secondary circuits currently used at the power plant have been outlined. Also the construction geometry and design of test facilities PACTEL and VEERA, as well as the operation principles of their main equipment has been described. Finally, the appropriate water chemistry and water treatment system have been proposed for the existing and future experimental facilities of LUT.

Mikro-ORC-energianmuuntimen suorituskyvyn todentaminen ja kaupallistaminen

Tässä työssä esitellään yleisesti ORC-prosessi, sen toimintaperiaate ja käyttökohteet. Työn tavoitteena oli todentaa diesel-moottorin savukaasujen lämpöenergian sähköenergiaksi muuntavan mikro-ORC-energianmuuntimen suorituskyky. Suorituskyky pyrittiin toteamaan laskemalla laboratoriomittauksista saadusta datasta koelaitoksen sähköntuotannon hyötysuhde ja vertaamalla sitä mallinnuksessa laskettuun hyötysuhteeseen. Esitys käytännöstä suorituskyvyn todentamiseen kuuluu työn sisältöön. Koelaitoksen suorituskykyä ei pystytty toteamaan turbogeneraattoriin liittyvien ongelmien vuoksi. Tarkasteltavaksi tähän työhön jäi koelaitoksen suorituskykyyn olennaisesti liittyvien laitoskomponenttien toiminta niille tyypillisten mittausdatasta laskettujen tunnuslukujen kautta. Koelaitoksella käytettyjen lämmönsiirrinten todettiin olevan kykeneviä siirtämään tarpeeksi lämpöenergiaa 130 kW jarruteholla toimivan diesel-moottorin savukaasujen lämmöstä sähköenergian tuotantoon. Laitoksen kaupallistamista tarkasteltiin asiakkaan ja valmistajan näkökulmasta. Tarkasteluun sisältyi katsaus kaupalliseen versioon kuuluvista ominaisuuksista, alihankinnasta ja säädöksistä, jotka laitoksen on täytettävä markkinoille päästäkseen.

Asiakasarvopohjaisten palveluiden kehittäminen kiinteistöpalvelualan yrityksessä

Tämän työn tavoitteena oli tutkia asiakasarvopohjaisten palveluiden kehittämistä ja luoda kiinteistöpalvelualan yritykselle kehitysprosessimalli, jonka avulla yritys voisi optimoida toimintojaan tulevaisuudessa. Tutkimuksen päätavoitteina oli tutkia asiakasarvoa kiinteistöpalveluissa, kartoittaa potentiaalisten uusien asiakkaiden palveluiden nykytila ja toiveet sekä tarkastella kohdeyrityksen palveluiden kehitysprosessia. Työn teoreettisessa osiossa tarkasteltiin palveluliiketoimintaa yleisellä tasolla, yrityksen palveluprosessin kehittämistä, asiakasarvon muodostumista sekä SERVQUAL- ja QFD-työkalujen avulla palvelun laatua ja asiakastarpeita. Työn teoriaosuuden kautta saatiin myös selville, että asiakasarvon hallinta on palveluiden kehitysprosessin ydin. Tutkimuksen empiirinen aineisto kerättiin syvähaastatteluiden avulla avainasiakkailta eri asiakassegmentteihin liittyen. Haastattelujen analysoinnissa hyödynnettiin laadullista sisällönanalyysiä. Työn tuloksissa määriteltiin asiakasarvo ja tärkeimmät asiakastarpeet kiinteistöpalveluissa, kartoitettiin asiakkaiden odotusten ja nykytilan väliset kuilut sekä luotiin yritykselle palveluiden kehitysprosessimalli, jota yritys voi toiminnoissaan tapauskohtaisesti hyödyntää tulevaisuudessa.

The Impact of Foreign Direct Investment Inflows on the Economic Growth of Bangladesh. The Roles of Infrastructural Facilities

Foreign direct investment (FDI) inflow has been a key concern for Bangladesh to obtain additional support for the economic development. The Government of Bangladesh continuously competing with other South Asian countries and putting more effort to increase the number of FDI inflows in the country. From the country’s perspective, the constant increasing rate of economic growth shows a positive outcome of FDI inflow. However, the country still not performing up to the mark to pull enough FDI inflows to its potential. Thus, this study discusses about the major determinants and factors affecting FDI inflows in Bangladesh. Among those determinants and factors, infrastructural facility is considered as the most important to affect FDI inflows. FDI inflow is fundamentally depending upon infrastructural facilities to achieve its desire success. Foreign investors take this issue very seriously because based on this they can measure their ease of doing business in the host country. Despite of providing a large market size, due to having weak and lack of infrastructural facilities, Bangladesh is facing trouble in drawing attention of the foreign investors. In order to make the infrastructural facilities happen, it is highly required to organize each of the systems under of it. The body of this study discussed about the weak infrastructures in Bangladesh such as transport and communication, power and energy, education system, and governance services. Improvement in one of these systems cannot provide valuable positive changes on FDI inflows. It requires improvement in all the weak systems to grasp multinational companies and attract foreign investors. On the basis of this research problem, research questions are established. Both qualitative and quantitative methods are used to answer the research questions. Furthermore, several theories have been applied to justify possible scenarios from the research problem. In addition, the history in between Bangladesh, trade liberalization, and FDI inflows is presented briefly.

The Impact of Foreign Direct Investment Inflows on the Economic Growth of Bangladesh. The Roles of Infrastructural Facilities

Foreign direct investment (FDI) inflow has been a key concern for Bangladesh to obtain additional support for the economic development. The Government of Bangladesh continuously competing with other South Asian countries and putting more effort to increase the number of FDI inflows in the country. From the country’s perspective, the constant increasing rate of economic growth shows a positive outcome of FDI inflow. However, the country still not performing up to the mark to pull enough FDI inflows to its potential. Thus, this study discusses about the major determinants and factors affecting FDI inflows in Bangladesh. Among those determinants and factors, infrastructural facility is considered as the most important to affect FDI inflows. FDI inflow is fundamentally depending upon infrastructural facilities to achieve its desire success. Foreign investors take this issue very seriously because based on this they can measure their ease of doing business in the host country. Despite of providing a large market size, due to having weak and lack of infrastructural facilities, Bangladesh is facing trouble in drawing attention of the foreign investors. In order to make the infrastructural facilities happen, it is highly required to organize each of the systems under of it. The body of this study discussed about the weak infrastructures in Bangladesh such as transport and communication, power and energy, education system, and governance services. Improvement in one of these systems cannot provide valuable positive changes on FDI inflows. It requires improvement in all the weak systems to grasp multinational companies and attract foreign investors. On the basis of this research problem, research questions are established. Both qualitative and quantitative methods are used to answer the research questions. Furthermore, several theories have been applied to justify possible scenarios from the research problem. In addition, the history in between Bangladesh, trade liberalization, and FDI inflows is presented briefly

Operatiivinen säteilysuojelu Posivan kapselointi- ja loppusijoituslaitoksella

Olkiluodon ja Loviisan ydinvoimalaitoksilla syntyvä käytetty ydinpolttoaine tullaan kapseloimaan ja loppusijoittamaan Posiva Oy:n kapselointi- ja loppusijoituslaitoksella, joka rakennetaan Olkiluotoon. Käytetyn polttoaineen käsittelyssä on huomioitava säteilytyöhön liittyviä säteilysuojelunäkökohtia. Kapseloinnissa ja loppusijoituksessa käsitellään vaarallisia säteilylähteitä, joista merkittävimmät ovat käytetty ydinpolttoaine ja täyden loppusijoituskapselin röntgentarkastuslaitteisto. Posivan laitosten käyttötoiminnalle muodostetaan tässä diplomityössä säteilysuojelun vaatimusmäärittely. Kapseloinnin ja loppusijoituksen säteilytyövaiheet käsitellään yksitellen säteilysuojelun näkökulmasta. Työvaiheille määritetään tarpeelliset säteilysuojelutoimenpiteet ja työvaiheiden suorittamisen säteilysuojeluvaatimukset. Molempien laitosten valvonta-aluejärjestelyjä ja säteilyolosuhteiden vyöhykejakoa tarkennetaan. Työssä määritetään vyöhyke- ja aluerajoilla vaadittavat säteilysuojelutoiminnot sekä kontaminaationhallinnan laatuvaatimukset. Työssä käsitellään myös operatiivisen säteilysuojelun toimenpiteiden laatuvaatimuksia ja tarvittavaa säteilysuojelun sisäistä ohjeistoa. Työn tuloksena on kapselointi- ja loppusijoituslaitoksen käyttötoiminnan operatiivisten säteilysuojelutoimenpiteiden kuvaus. Kapselointi- ja loppusijoituslaitosten säteilysuojelua toteutetaan käyttövaiheen työnsuunnittelulla, operatiivisilla säteilysuojelutoimilla ja rakenteellisin keinoin. Työntekijöiden säteilyannokset minimoidaan välttämällä oleskelua kohonneen säteilytason alueilla. Kapselin röntgentarkastuslaitteiston käytön säteilyturvallisuus on varmistettava ja laitosten käyttötoiminta ei saa aiheuttaa työntekijöille sisäistä säteilyannosta. Useista työvaiheista ja käyttötoiminnan poikkeustilanteista on tehtävä jatkoanalyyseja työntekijöiden säteilysuojelun näkökulmasta.

Kaupallisen sekajätteen mekaaniset käsittelyprosessit ja laitos investoinnin kannattavuus

Työn tavoitteena oli tutkia mekaanisia käsittelylaitteita ja -prosesseja kaupalliselle sekajätteelle ja selvittää mahdollisen laitoshankkeen kannattavuutta case-yritykselle. Jätehuollon yritykset ovat jatkuvan muutoksen alla kasvavien keräys- ja käsittelykustannusten takia, joka vaatii säästöjen etsimistä. Sekajäte sisältää arvokkaita kierrätysraaka-aineita ja näiden erottelu voisi luoda lisäarvoa alentuneina hävityskustannuksina ja lisääntyneinä myyntituottoina. Työssä selvitettiin kaupallisen sekajätteen koostumusta lajittelukokeen ja muiden sekajätetutkimusten avulla. Mekaanisia käsittelylaitteita tutkittiin kirjallisuuden ja case-esimerkkien kautta. Laitoshakkeen kannattavuutta arvioitiin taulukkolaskentamallin avulla. Laitosvaihtoehtoja tarkasteltiin 10-30 tuhannen tonnin kapasiteetin välillä. Laskelmien ja kirjallisuustutkimuksen pohjalta kannattavimpana vaihtoehtona nähtiin SRF kierrätyspolttoainetta valmistava laitos. Kirjallisuustutkimuksen ja case-laitosten pohjalta luotiin kaksi investointiskenaariota, joille laskettiin taulukkolaskentamallin avulla yksikkökustannukset, nettonykyarvot ja sisäiset korot. Kustannusaineisto oli peräisin case-yritykseltä ja muista laitostutkimuksista. Kannattavuuslaskelmien mukaan skenaario 2, jossa SRF-tuotannon lisäksi eroteltaisiin sekalaisia muoveja, on kannattavampi. Skenaarioiden 1 ja 2 kriittiset pisteet olivat noin 15,3 ja 13,6 tuhatta tonnia vuodessa. Kumpikaan skenaarioista ei kuitenkaan ole kannattava case-yrityksen omilla vuotuisilla kuormilla (10 000 tonnia). Lisää käsiteltävää jätettä tulisi hankkia ulkopuolisilta yrityksiltä taloudellisesti edullisen vaakamaksun avulla. Skenaarion 2 ongelmaksi kuitenkin muodostuu sekalaisten muovien poistuminen SRF:n komponenttina, mikä vaikuttaa SRF:n markkinoitavuuteen tehollisen lämpöarvon alenemisen takia.

Remote Observation of Radioactive Permit-Required Confined Spaces – Case: Posiva Oy’s Fuel Handling Cell

Posiva Oy’s final disposal facility’s encapsulation plant will start to operate in the 2020s. Once the operation starts, the facility is designed to run more than a hundred years. The encapsulation plant will be first of its kind in the world, being part of the solution to solve a global issue of final disposal of nuclear waste. In the encapsulation plant’s fuel handling cell the spent nuclear fuel will be processed to be deposited into the Finnish bedrock, into ONKALO. In the fuel handling cell, the environment is highly radioactive forming a permit-required enclosed space. Remote observation is needed in order to monitor the fuel handling process. The purpose of this thesis is to map (Part I) and compare (Part II) remote observation methods to observe Posiva Oy’s fuel handling cell’s process, and provide a possible theoretical solution for this case. Secondary purpose for this thesis is to provide resources for other remote observation cases, as well as to inform about possible future technology to enable readiness in the design of the encapsulation plant. The approach was to theoretically analyze the mapped remote observation methods. Firstly, the methods were filtered by three environmental challenges. These are the high levels of radiation, the permit-required confined space and the hundred year timespan. Secondly, the most promising methods were selected by the experts designing the facility. Thirdly, a customized feasibility analysis was created and performed on the selected methods to rank the methods with scores. The results are the mapped methods and the feasibility analysis scores. The three highest scoring methods were radiation tolerant camera, fiberscope and audio feed. A combination of these three methods was given as a possible theoretical solution for this case. As this case is first in the world, remote observation methods for it had not been thoroughly researched. The findings in this thesis will act as initial data for the design of the fuel handling cell’s remote observation systems and can potentially effect on the overall design of the facility by providing unique and case specific information. In addition, this thesis could provide resources for other remote observation cases.

Diversity in the fitness industry : a cross-case comparison /

This cross-case study explored the extent to which two fitness facilities were accommodating diversity with respect to age, ethnicity, gender, social class, sex-role socialization, and persons with a disability among both members and staflf. The sites were purposely chosen in a large city and a smaller city in order to provide as representative an example as possible of health clubs within a small sample population. The interview participants were selected by a combination of stratified, typical case, and snowball sampling strategies. . , .. , The intent of the exploration was a two-fold examination of diversity issues within both the membership and the staff of the organization. Data were collected and analysis was done using a triangulation method involving personal interviews, observations, and facility documentation. The results ofthe study showed that the members and staff at each facility were rather homogeneous in ethnicity, age, social class, physical ability, and physical appearance. From a membership standpoint, the environment of the sites presented the impression of being affordable only to the middle- and upper-middle classes, unwelcoming to the older, less fit, or overweight participant, economically exclusive for youth, and nonaccommodating for people with a disability. With respect to staff, the findings indicated that the fitness facilities purported to be team-oriented in theory, but were hierarchical in practice, with the major decision making being made by the male executives. The paper concludes with the recommendation that students must be given a practical toolkit for dealing with these issues in their postsecondary courses.

Nursing staffs' perceptions of a generic service manager position

The recent reengineering within the health care industry has challenged many assumptions regarding traditional structures and roles. Within a product-line management structure, the traditional viewpoint that those who manage patient care areas must have a nursing background, is an example of one such assumption being challenged. The nursing profession is often seen as the greatest obstacle to the implementation of a product-line management structure and generic manager positions (does not require a nursing background), due to the perceived loss of professional identity. This qualitative study focused on how nursing staff within a chronic care and rehabilitation facility perceived a generic service manager position. Focus groups were conducted in three phases, over a 14 month period of time. The data collected from the focus groups were then coded according to common themes. Each phase was analyzed independently, with the study concluding with an analysis and interpretation of the collective results. The results of this study revealed a significant shift in how the nursing staff perceived their professional identity and accountability in light of the implementation of the generic Service Manager position. Initial reactions of personal and professional vulnerability and resentment were seen to transform into an increased ability to explicitly articulate the role of nursing. Changes in behavior that were described included: increased consultation and collaboration with other

Organizational change: implications of culture and leadership in the transformation to a total quality management paradigm

The study was undertaken to investigate organizational readiness for change to a total quality management (TQM) paradigm as the corporate-wide strategy within a long-term care facility. The focus of the study was on leadership values and organizational cultural characteristics that could either accelerate or impede the change process at The Public Hospital. structurally, the ~tudy included 'three distinct components. The first component examined the management philosophy outlined by Deming (1986) and his contemporary Juran (1989) in order to determine what leadership values best support the new Total Quality Management paradigm. Secondly, this information was compared to present leadership values at The Public Hospital with the purpose of identifying opportunities for improvement within the organization's current culture as the hospital moves toward the desired TQM culture. The final component, a roadmap, was developed to reflect the most appropriate direction for organizational change at The Public Hospital.