Development of a Ceramic Membrane Filtration Equipment and Its Applicability for Different Wastewaters

In this thesis the membrane filtration equipment for plate type ceramic membranes was developed based on filtration results achieved with different kinds of wastewaters. The experiments were mainly made with pulp and board mill wastewaters, but some experiments were also made with a bore well water and a stone cutting mine wastewater. The ceramicmembranes used were alpha-alumina membranes with a pore size of 100 nm. Some ofthe membranes were coated with a gamma-alumina layer to reduce the membrane pore size to 10 nm, and some of them were modified with different metal oxides in order to change the surface properties of the membranes. The effects of operationparameters, such as cross-flow velocity, filtration pressure and backflushing on filtration performance were studied. The measured parameters were the permeateflux, the quality of the permeate, as well as the fouling tendency of the membrane. A dynamic membrane or a cake layer forming on top of the membrane was observed to decrease the flux and increase separa-tion of certain substances, especially at low cross-flow velocities. When the cross-flow velocities were increased the membrane properties became more important. Backflushing could also be used to decrease the thickness of the cake layer and thus it improved the permeate flux. However, backflushing can lead to a reduction of retentions in cases where the cake layer is improving them. The wastewater quality was important for the thickness of the dynamic membrane and the membrane pore size influenced the permeate flux. In general, the optimization of operation conditions is very important for the successful operation of a membrane filtration system. The filtration equipment with a reasonable range of operational conditions is necessary, especiallywhen different kinds of wastewaters are treated. This should be taken into account already in the development stage of a filtration equipment.

Residues of carbosulfan and its carbofuran metabolites and 3-hydroxy-carbofuran in oranges

The objectives of this study were to evaluate the residues of the insecticide carbosulfan and its carbofuran metabolites and 3-hydroxy-carbofuran in orange compartments (whole fruit, bagasse and juice) and comparison between the residual levels found in fruits with the maximum residue level and the safety interval established by the Brazilian legislation. Two field experiments were carried out, both with the following treatments: a-check; b-one application of 10 g of carbosulfan . 100 L-1 of water; c-one application with twice the rate applied in treatment b; d-four applications with the same rate applied in treatment b. Samples were taken at (-1), zero, 1, 3, 7, 14, 21 and 28 days after the last or unique application. The quantitative determinations were done by gas chromatography technique, using a nitrogen-phosphorus detector. The carbosulfan metabolism to its carbofuran metabolite was rapid (3 days), being both analytes concentrated in the bagasse (peel + flavedo + albedo). However, the metabolism of carbofuran to 3-hydroxy-carbofuran was of low intensity or this metabolite was quickly dissipated. Carbosulfan residues and its metabolites did not penetrate into the fruit, thus not contaminating the juice. The use of the pesticide was adequate, with respect to fruit consumption, in relation to the Brazilian legislation.

Qualidade dos frutos de tipos de melão,produzidos em ambiente protegido

O interesse pela cultura do melão no Brasil tem aumentado muito nos últimos anos, pelas crescentes exportações e pelo incremento no consumo do mercado interno. O objetivo deste trabalho foi avaliar as características físicas e químicas, assim como a atividade da pectinametilesterase dos frutos de tipos de melão (Cucumis melo L.), produzidos em ambiente protegido, no município de Centenário do Sul-PR. Os tipos estudados foram: Valenciano ('Amarelo-Ouro'), Caipira ('Gaúcho Caipira'), Net Melon ('Net Galia'), Orange ('Orange Melon') e Pele-de-Sapo ('Filipo'), com cinco repetições, utilizando seis frutos por repetição em delineamento inteiramente casualizado. Os frutos do Valenciano e Pele-de-Sapo destacaram-se quanto à massa, com valores 2,02 e 2,07 kg, respectivamente, e formatos alongados, enquanto os demais tipos apresentaram formatos arredondados e massa em torno de 1,4 kg. Os melões Pele-de-Sapo apresentaram espessura da polpa de 43,36 mm, estatisticamente superior à dos frutos Valenciano, com 38,98 mm. A menor espessura de polpa, 24,78 cm, e a maior espessura de casca, 9,74 mm, foram encontradas nos frutos do tipo Caipira que diferiu estatisticamente dos outros tipos. Os valores de pH não se apresentaram estatisticamente diferentes e variaram de 6,24 a 6,48. O Net Melon apresentou polpa com 12,3ºBrix e diferiu estatisticamente do Orange, Valenciano e Pele-de-Sapo, com 11;12; 10,34 e 9,94 ºBrix, respectivamente. O Caipira atingiu 5,06ºBrix, e também o menor conteúdo de acidez, 0,10 g de ac. cítrico.100-1 g de suco, o que inviabiliza sua comercialização. A atividade da pectinametilesterase na polpa dos frutos foi muito baixa, inferior a 0,005 PEu x 10(4) mL-1, nos cinco tipos avaliados. Na região norte do Paraná (Vale do Paranapanema), sob condições de cultivo protegido, os melões Pele-de-Sapo, Net Melon, Orange e Valenciano apresentaram boas características físicas e químicas dos frutos, destacando-se o Net Melon pelo teor de sólidos solúveis totais, acima de 12ºBrix.

Passiflora edulis Sims: the correct taxonomic way to cite the yellow passion fruit (and of others colors)

Passiflora edulis, the passion fruit native from Brazil, has several common names (such as sour passion fruit, yellow passion fruit, black passion fruit, and purple passion fruit), and presents a wide variability with the different rind colors of its fruits, which are very easy to notice. However, in 1932, Otto Degener suggested that the yellow passion fruit had its origin in Australia through breeding, calling it P. edulis forma flavicarpa, and that it could be distinguished by the color of the fruit, the deeper shade of purple of the corona, and the presence of glands on the sepals. These distinctions do not support themselves, for the glands are common to the species (although they may be absent), and the corona has a wide range of colors, regardless of the color of the fruit. A more critical ingredient is the fact that the external coloration of the fruit is a character of complex inheritance and is not dominant, thus displaying a number of intermediate colors, making it difficult to identify the extreme colors. For the correct scientific naming of agricultural plants, the International Code of Botanical Nomenclature must be used in conjunction with the International Code of Nomenclature for Cultivated Plants, with the selections with significant agronomic characteristics recognized and named cultivars. In accordance with the international convention promoted by the UPOV, of which Brazil is a signatory, several colors (light yellow, yellow, orange yellow, pink red, red, red purple, green purple, purple, and dark purple) can be recognized in order to adequately characterize passion fruit cultivars within the species P. edulis. At taxonomic level, Passiflora edulis Sims must be used for any plant and color of sour passion fruits, in combination with a cultivar name for the selected materials.

Use of the heat dissipation method for sap flow measurement in citrus nursery trees1

Sap flow could be used as physiological parameter to assist irrigation of screen house citrus nursery trees by continuous water consumption estimation. Herein we report a first set of results indicating the potential use of the heat dissipation method for sap flow measurement in containerized citrus nursery trees. 'Valencia' sweet orange [Citrus sinensis (L.) Osbeck] budded on 'Rangpur' lime (Citrus limonia Osbeck) was evaluated for 30 days during summer. Heat dissipation probes and thermocouple sensors were constructed with low-cost and easily available materials in order to improve accessibility of the method. Sap flow showed high correlation to air temperature inside the screen house. However, errors due to natural thermal gradient and plant tissue injuries affected measurement precision. Transpiration estimated by sap flow measurement was four times higher than gravimetric measurement. Improved micro-probes, adequate method calibration, and non-toxic insulating materials should be further investigated.

Control of Guignardia citricarpa by Bacillus subtilis and Trichoderma spp.

The ability of isolates of Bacillus subtilis and Trichoderma spp. to control citrus black spot (CBS) was investigated in ´Natal´ sweet orange orchards. The first experiment was conducted during the 2001/2002 season and four isolates of B. subtilis (ACB-AP3, ACB-69, ACB-72 and ACB-77), applied every 28 days, alone or in combination were tested and compared with fungicide treatments. Two other experiments were carried out during the 2002/2003 season, where the same isolates of Bacillus and two isolates of Trichoderma (ACB-14 and ACB-40) were tested being applied every 28 days in the second experiment, and every 15 days in the third experiment. In the first experiment, the treatment with ACB-69 differed statistically from the control, but did not differ from other biological control agents or mixture of Bacillus isolates. In the second experiment, the treatments with ACB-69 and ACB-AP3 resulted in smaller disease index compared with the control treatment. However, this result was not repeated in the third experiment, where the isolates were applied every 15 days. Disease severity was high in both evaluated seasons and the fungicide treatment was the most effective for disease control.

Characterization and drying of caja bagasse (Spondias mombin L.) in a tray dryer using a factorial planning

The caja (Spondias mombin L.) is used in the manufacture of ice-cream, jams, pulps, beverages being also consumed in natura. One of the most important procedures in food conservation is drying, considering that most fresh fruits contain approximately 80% of water. Food drying is used to obtain two basic aspects: (1) the economic factor; in the shipping and handling of the product; (2) at the manipulation; once dried and grinded, the material is rehydrated, at desirable levels, to formulate a new product as in ice cream, jams, yoghurts and drinks and may also be added to pasta, biscuits and other industrialized products. The aim of this study was to investigate the kinetics of caja bagasse drying in a fixed-bed tray dryer, using central composite factorial planning. The following factors were evaluated: temperature (55, 65 and 75 ºC), dryer inlet air velocity (3.2, 4.6 and 6.0 m.s-1) and cake thickness (0.8, 1.2 and 1.6 cm) where the response of the considered variable was caja bagasse moisture content (b.s.) and the results showed that the main effects and their interactions were significant at a 95% confidence level being the best condition obtained at temperature of 75 ºC, velocity of 6.0 m.s-1 and cake thickness of 0.8 cm.

Avaliação genética de seleções e híbridos de limões cravo, volkameriano e rugoso como porta-enxertos para laranjeiras Valência na presença da morte súbita dos citros

Este estudo teve como objetivo realizar a avaliação genética da produção de frutos, eficiência produtiva e altura de laranjeiras Valência (Citrus sinensis) enxertadas em seleções e híbridos dos limões Cravo (C. limonia), Volkameriano (C. volkameriana) e Rugoso (C. jambhiri), em área endêmica para morte súbita dos citros (MSC). Foram avaliados 36 genótipos desses porta-enxertos, representados por cinco plantas cada, avaliados em cinco safras, do terceiro ao sétimo ano após o plantio. Sete dos genótipos avaliados apresentaram plantas com sintomas de MSC até o sétimo ano: Rangpur Otaheite orange 12901 (859), Rangpur Red Lime D.33.30 (866), Limão-Cravo EEL (871), Rangpur Borneo red (874), Citrus kokhai (1649), Limão-Rugoso 58329 (1655) e Limão- Cravo x Swingle B (1695). Para os genótipos que não manifestaram sintomas da doença, foram estimados parâmetros genéticos e fenotípicos e realizada a predição de valores genéticos dos indivíduos, visando à seleção e ao melhoramento genético para as características citadas, empregando-se o método REML/BLUP (máxima verossimilhança restrita/melhor predição linear não viciada). A análise de produção de frutos de cinco safras mostrou acurácia seletiva de 84,59%, tornando-se desnecessária a avaliação de maior número de safras. A seleção dos sete melhores genótipos proporcionou ganhos genéticos de 11,5% na produção de frutos, enquanto a do melhor genótipo conferiu ganho genético de 16,3%. As maiores médias genéticas preditas (>70,0 kg.pl-1) para produção de frutos foram obtidas pelos genótipos Limão-Cravo- Ipanema (1522), Santa- Bárbara-Red- Lime (884), Limão- Cravo- Limeira (863), Limão- Cravo- Taquaritinga (869), Limão- Rugoso- do -Cabo (1643), Rangpur- Rose Lime (868) e Limão- Cravo- da- Califórnia (1467). Já a acurácia seletiva da eficiência produtiva, para quatro colheitas, foi 77,4%. Para este caráter, as maiores médias genéticas (>8,0 kg.m-3) foram dos genótipos Rangpur- Lime x Trifoliata 3810 (1648), Rangpur- Lime x Trifoliata 5320 (1644), Limão- Cravo x Citrange- Carrizo (1524), Citrus pennivesiculata (880), Limão- Cravo x Trifoliata- Swingle A (1707), Rangpur- Rose- Lemon 124684 (864), Rangpur- Red -Lime D33.47 (867) e Limão- Cravo -Ipanema (1522). Dentre os 10 melhores genótipos para produção de frutos e para eficiência produtiva, apenas três são coincidentes: Rangpur- Rose -Lime (868), Citrus pennivesiculata (880) e Limão- Cravo-Ipanema (1522).

Monitoring the viability of citrus rootstocks seeds stored under refrigeration

The citrus nursery tree is produced through the bud grafting process, in which rootstock is usually grown from seed germination. The objective of this research was to evaluate, in two dissimilar environmental conditions, the viability and polyembryony expression of five citrus rootstocks seeds stored in different periods under refrigeration. The rootstock varieties evaluated were: Rangpur lime (Citrus limonia Osb. cv. Limeira), Trifoliate orange (Poncirus trifoliata Raf. cv. Limeira), Citrumelo (P. trifoliata x C. paradisi Macf. cv. Swingle), Sunki mandarin (C. sunki Hort. ex Tanaka) and Volkamer lemon (C. volkameriana Ten. & Pasq. cv. Catania 2). The experimental design was the randomized blocks in a 11 x 5 x 2 factorial scheme, evaluating from time zero to the tenth month of storage, the five varieties of rootstock in two environments: germination and growth B.O.D type chamber (Biological Oxygen Demand - Eletrolab Brand Model FC 122) at 25 °C; and greenhouse seedbed with partial temperature control (22 °C to 36 °C) and humidity control (75-85%). The plot had 24 seeds in four replicates, using trays with substrate in greenhouse and Petri dishes with filter paper in B.O.D. chamber. The seed germination rate and polyembryony expression were evaluated monthly. It was concluded that Trifoliate and Citrumelo Swingle seeds can be stored for up to seven months, while Volkamer lemon, Rangpur lime and Sunki seeds can be stored for up to ten months. The polyembryony expression rate was slightly higher when measured in greenhouse than in B.O.D. chamber and remained stable in both environments until the seventh month, from which dropped sharply. Citrumelo Swingle seeds expressed the highest polyembryony rate (18.8%), followed by Rangpur lime and Volkamer lemon (average value of 13.7%), Sunki (9.4%) and Trifoliate (3.2%). Despite some differences among varieties, the viability of rootstock stored seeds can be monitored either in the greenhouse or in B.O.D. germination chamber, the latter being the faster and more suitable method.

Hidrogenionic potential (pH) of the attractant, trap density and control threshold for Ceratitis capitata (DIPTERA: TEPHRITIDAE) on Hamlin oranges in São Paulo central region, Brazil

This study evaluated the effect of initial pH values of 4.5, 6.5 and 8.5 of the attractant (protein bait) Milhocina® and borax (sodium borate) in the field, on the capture of fruit flies in McPhail traps, using 1, 2, 4 and 8 traps per hectare, in order to estimate control thresholds in a Hamlin orange grove in the central region of the state of São Paulo. The most abundant fruit fly species was Ceratitis capitata, comprising almost 99% of the fruit flies captured, of which 80% were females. The largest captures of C. capitata were found in traps baited with Milhocina® and borax at pH 8.5. Captures per trap for the four densities were similar, indicating that the population can be estimated with one trap per hectare in areas with high populations. It was found positive relationships between captures of C. capitata and the number of Hamlin oranges damaged, 2 and 3 weeks after capture. It was obtained equations that correlate captures and damage levels which can be used to estimate control thresholds. The average loss caused in Hamlin orange fruits by C. capitata was 2.5 tons per hectare or 7.5% of production.

Puumassapesurin suotautumisolojen kartoitus ja simulointi

Työn tavoitteena oli tutkia sellumassan suotautumiseen liittyviä tekijöitä Ahlstrom Machineryn Drum Displacer™ -puumassapesurissa (DD-pesuri). Teoriaosassa tarkasteltiin aluksi suotautumisen teoriaa kuitu-vesi-suspensiossa, minkä jälkeen esiteltiin suotautumisnopeuteen vaikuttavia fysikaalisia ja kemiallisia vaikutusmekanismeja. Seuraavaksi kuvattiin massan pesun yleisiä perusteita sekä teoriaa puumassapesureissa. Lopuksi tarkasteltiin pesurien kytkeytymistä muuhun kuitulinjaan sekä prosessista johtuvia pesun toiminnan ulkoisia häiriötekijöitä. Kokeellisen osan aluksi tarkasteltiin paine- ja lämpötilamittauksien avulla massapesurissa vallitsevia prosessioloja. Mittaustulosten perusteella pumppausolot pesurin suodoslinjoissa ovat vaikeahkot ja häiriötilanteita voi esiintyä, mutta käytäntö on osoittanut tästä olevan vain harvoin haittaa prosessin toiminnalle. Pesureissa toteutuneet syrjäytysnopeudet laskettiin ja niitä verrattiin syrjäytystestien antamiin tuloksiin. Kuitulinjasta riippuen testin vastaavuus tehdasprosessiin vaihteli suuresti. Syrjäytystesteillä kokeiltiin myös tehdasprosesseissa usein esiintyvien muuttujien vaikutusta sellukakun syrjäytettävyyteen. Kakun paksuus ja syrjäytyslämpötila vaikuttivat syrjäytysnopeuteen Darcyn lain mukaisesti. Alipaineen massakakun alapuolella havaittiin huonontavan syrjäytysnopeutta verrattuna tilanteeseen, jossa kakun alla vallitsi ilmanpaine. Tämä havainto on selvästi ristiriidassa suotautumisen teorian kanssa. Massakakun muodostumis-pH osoittautui ratkaisevaksi lopulliselle syrjäytysnopeudelle, sillä alkalisissa oloissa muodostetun kuitukakun syrjäytysnopeus ei enää parantunut happamalla syrjäytysnesteellä. Happamissa oloissa muodostetun kakun syrjäytysnopeus oli alkalisista parempi, mutta se alkoi hitaasti alentua, kun syrjäytysneste vaihtui alkaliseen. Massan laimentaminen ennen syrjäytystä alkalisella tehdassuodoksella puhtaan veden sijasta alensi ligniinipitoisella massalla lopullista syrjäytysnopeutta. Shirato-Tillerin mallilla ja Jönssonin staattisella mallilla simuloitiin numeerisesti syrjäytystestiä kahdessa eri pH:ssa, ja simulointituloksia verrattiin vastaavissa oloissa tehtyihin syrjäytystesteihin. Shirato-Tillerin mallin antamien syrjäytysnopeuksien havaittiin olevan lähellä syrjäytystestien nopeuksia, kun Jönssonin mallin antamat tulokset jäivät huomattavasti testituloksia alemmiksi. Herkkyystarkastelussa havaittiin mallien olevan varsin herkkiä parametrien virheille. Hajonta vaadittavien kuituparametrien määrityksissä ja menetelmien työläys rajoittavat numeerisen simuloinnin käytettävyyttä, sillä kuituparametrien määrityksen vaatima työmäärä on ainakin toistaiseksi syrjäytystestiä suurempi. Lopuksi todettiin, että oikeiden syrjäytysolosuhteiden käyttö on ensiarvoisen tärkeää oikeiden tulosten saamiseksi sekä kokeellisessa että numeerisessa simuloinnissa. Nykyinen syrjäytystestilaitteisto on pienin muutoksin käyttökelpoinen, kun massan testaus prosessioloissa tulee rutiininomaiseksi.

Transmission properties of high barrier coated paperboard packages

High barrier materiaaleilla pyritään pidentämään pakattujen elintarvikkeiden hyllyikää. Barrierin tärkein tehtävä on elintarvikkeen suojaaminen hapelta ja kosteudelta. Alumiinin käyttöä barriermateriaalina pyritään vähentämään korvaamalla alumiini polymeereillä, jotka täyttävät elintarvikkeiden asettamat korkeat säilyvyysvaatimukset. Etyylivinyylialkoholin (EVOH) hapenläpäisevyys on kuivissa olosuhteissa alhaisin kaupallisista muovilaaduista. EVOH tarjoaa myös erinomaisen suojan muita kaasuja, rasvoja, hajuja ja aromeja vastaan ja sitä on helppo prosessoida. Polyamideilla on erinomainen kaasutiiveys sekä hyvä lujuus ja sitkeys. Eri muovilaatuja sekoittamalla voidaan vähentää hapenläpäisyä ja parantaa prosessointia. Polyolefiineja käytetään yleisesti päällystysmateriaaleina, koska ne suojaavat tuotetta erinomaisesti kosteudelta. Hapenläpäisyllä tarkoitetaan hapen kulkeutumista materiaalin läpi joko permeaation kautta tai reikien ja vuotojen läpi. Kaasun permeoitumiseen materiaalin läpi vaikuttavat materiaalin vapaa tilavuus, kiteisyysaste, orientaatio, substituointi, suhteellinen kosteus, lämpötila, barrierkerroksen paksuus, paine-ero ja permeoituvan molekyylin ominaisuudet. Kokeellisessa osassa analysoitiin ja vertailtiin kartonkipohjaisia mehutölkkejä, joissa käytettävät high barrier materiaalit olivat EVOH ja PA. Kartonkipohjaisia alumiinitölkkejä käytettiin referenssinä. Pakkausten hapenläpäisevyysmittauksissa saatiin samasta näytteestä toistettavia tuloksia, vaikka vuotomittauksissa saadut tulokset eivät olleet vertailukelpoisia hapenläpäisytulosten kanssa. Tölkkien valmistus vaikutti oleellisesti pakkausten tiiveysominaisuuksiin. Hapenläpäisy vuotojen ja reikien läpi oli merkittävämpää kuin hapenläpäisy materiaalin läpi. Pakkausten tiiveysominaisuuksia analysoitiin mittaamalla appelsiinimehun askorbiini-happopitoisuus. Askorbiinihapon hajoaminen mitattiin koetölkkeihin pakatusta appelsiinimehusta, ja lämpötilan, valon ja hapen vaikutusta askorbiinihapon hajoamiseen tutkittiin 12 viikon ajan. Lämpötilalla oli suurin vaikutus askorbiinihapon hajoamiseen huolimatta käytetystä pakkausmateriaalista.

Marjojen flavonoidien uuttaminen

Flavonoidit ovat kasvien polyfenolisia sekundäärimetaboliitteja, jotka koostuvat 15-hiilisestä C6-C3-C6-perusrungosta. Niillä on havaittu useita terveyden kannalta edullisia ominaisuuksia kuten antioksidatiivisia, antikarsinogeenisia, antiallergeenisia, anti-inflammatorisia, estrogeenisia sekä antimikrobiaalisia vaikutuksia. Kasvimateriaalia käyttävän elintarviketeollisuuden sivuvirrat ovat flavonoidi-pitoisten jakeiden arvokkaita raaka-aineita. Tässä työssä tarkoituksena oli tutkia marjojen puristusjäännöksen sisältämien flavonoidien uuttamista ja uuttautumiseen vaikuttavia tekijöitä kuten liuottimen koostumusta ja määrää, uuttolämpötilaa ja -aikaa sekä liuottimen lisäaineita. Uutteet analysointiin HPLC:lla käyttäen ODS-2-kolonnia ja gradienttieluointia. Komponentit detektoitiin niille tyypillisillä UV-VIS-aallonpituuksilla ja identifioitiin vertaamalla flavonoidiprofiililtaan tunnettujen marjojen kromatogrammeihin. Antosyaanien kvantitatiiviseen analysointiin käytettiin spektrofotometrista pH-eromenetelmää ja tulokset ilmoitettiin syanidiini-3-glukosidina. Uutteiden kestävyyttä tutkittiin säilyttämällä näytteitä eri olosuhteissa sekä lisäämällä niihin uuton saantoon ja komponenttien säilyvyyteen vaikuttavia aineita. Useimmat tutkituista hapoista paransivat flavonoidien saantoa ja uutteiden säilyvyyttä, mutta esim. askorbiinihapon lisääminen nopeutti tiettyjen uutteen sisältämien flavonoidien tuhoutumista.

Production and quality of Anacardium othonianum Rizz. seedlings grown in different substrates

This study aimed to evaluate the effect of substrate on growth, emergence, nutrition, and quality of Anacardium othonianum Rizz. (cerrado cashew tree) seedlings. The experiment was conducted in a greenhouse at the Plant Tissue Culture Laboratory on the Rio Verde campus. The following substrates were used: 1) Bioplant®, 2) Mecplant® (MP) + carbonized rice husk (CRH) (7:3), 3) fine-grained vermiculite (FGV), 4) FGV+CRH (3:1), 5) FGV+CRH (1:1), 6) FGV+CRH (1:3), and 7) sugarcane bagasse (SB) + sugarcane mill filter cake (FC) (3:2). Emerged seedlings were counted at 2-day intervals for 38 days following emergence of the first seedling. At 39, 64, and 89 days after seeding (DAS), the following variables were measured: stem length (SL), stem diameter (SD), and number of leaves (NL). Accumulated dry weight, quality indices, and leaf macro- and micronutrient levels were determined at 89 DAS. Plants grown in the FGV and FGV+CFH (1:3) substrates had shorter stem lengths than the plants grown in other substrates. Increases in seedling growth were smaller between 64 and 89 DAS compared to the initial period of the experiment. The highest leaf N concentrations were found in the SB+FC substrate treatment group; P and K concentrations were higher for the MP+CRH (7:3), SB+FC, and Bioplant® treatments; and Ca levels were higher for the SB+FC and MP+CRH (7:3) substrate treatments. The MP+CRH (7:3) substrate treatment group had the highest leaf B and Mn micronutrient concentrations, and plants from the Bioplant® substrate group had the highest leaf B micronutrient content. Mg, S, Cu, Zn, and Fe concentrations did not differ among the different substrates. The plant traits that differed most among the treatments included stem length for the FGV and FGV+CRH (1:3) substrate groups and leaf nutrient concentrations, which were higher for the SB+FC group followed by the MP+CRH and Bioplant® treatments.

Pigmenttien suodatus

Työn tavoitteena oli tutkia neljän eri koesuotimen soveltuvuutta pigmenttilietteen kiintoainepitoisuuden nostoon. Työssä käytetyt suotimet olivat Larox PF 0,1, Certus-CU-0047, Crossflow-koesuodin ja Steuerung ET06-linko. Suodinväliaineena Larox PF 0,1-suotimessa ja Crossflow-koesuotimessa käytettiin Tamfelt Oyj:n suodinkankaita. Certus-CU-0047-suotimessa suodinväliaineena toimi keraaminen membraani. Työn kirjallisuusosassa tarkasteltiin partikkelien karakterisointia, suodatuksen teoriaa, kakkusuodatusta, suodinväliaineista suodinkankaita ja membraaneja. Lisäksi tarkasteltiin paperin päällystämiseen käytettyjen pigmenttien ominaisuuksia ja niiden suodatusta. Kokeet suoritettiin Larox PF 0,1, Certus-CU-0047 ja Crossflow-koesuotimella vakiopainesuodatuksena yhdellä paineella. Steuerung ET06-lingon kokeet suoritettiin vakiovirtaussuodatuksena käyttäen kolmea eri virtausnopeutta ja kolmea eri lingon ja ruuvin kierrossuhdetta. Työssä suodatettiin neljää erilaista pigmenttilietettä. Suodoksista otettiin näytteitä niiden sameuden määrittämiseksi. Larox Pf 0,1-suotimella ja Steuerung ET06-dekantterilingolla saatiin nostettua pigmenttilietteen kiintoainepitoisuutta erittäin hyvin. Loput kaksi suodinta eivät sovellu tähän tarkoitukseen ollenkaan. Vakiopainesuodatuksissa suodatusajat muodostuivat kuitenkin liian pitkiksi. Suodoksien kiintoainepitoisuudet olivat suurimmaksi osaltaan pieniä lukuun ottamatta tiettyjä suodinkankaita. Lietteen 2 kiintoainepitoisuuden nostaminen oli kaikilla suotimilla erittäin vaikeaa, muut lietteet suodattuivat kohtuullisen hyvin. Näiden kokeiden perusteella voidaan sanoa, että varsinkin vakiovirtaussuodatus soveltuu hyvin ainakin tiettyjen pigmenttilietteiden kiintoainepitoisuuden nostoon.