Inflow cannula design for biventricular assist devices

Cardiovascular diseases are a leading cause of death throughout the developed world. With the demand for donor hearts far exceeding the supply, a bridge-to-transplant or permanent solution is required. This is currently achieved with ventricular assist devices (VADs), which can be used to assist the left ventricle (LVAD), right ventricle (RVAD), or both ventricles simultaneously (BiVAD). Earlier generation VADs were large, volume-displacement devices designed for temporary support until a donor heart was found. The latest generation of VADs use rotary blood pump technology which improves device lifetime and the quality of life for end stage heart failure patients. VADs are connected to the heart and greater vessels of the patient through specially designed tubes called cannulae. The inflow cannulae, which supply blood to the VAD, are usually attached to the left atrium or ventricle for LVAD support, and the right atrium or ventricle for RVAD support. Few studies have characterized the haemodynamic difference between the two cannulation sites, particularly with respect to rotary RVAD support. Inflow cannulae are usually made of metal or a semi-rigid polymer to prevent collapse with negative pressures. However suction, and subsequent collapse, of the cannulated heart chamber can be a frequent occurrence, particularly with the relatively preload insensitive rotary blood pumps. Suction events may be associated with endocardial damage, pump flow stoppages and ventricular arrhythmias. While several VAD control strategies are under development, these usually rely on potentially inaccurate sensors or somewhat unreliable inferred data to estimate preload. Fixation of the inflow cannula is usually achieved through suturing the cannula, often via a felt sewing ring, to the cannulated chamber. This technique extends the time on cardiopulmonary bypass which is associated with several postoperative complications. The overall objective of this thesis was to improve the placement and design of rotary LVAD and RVAD inflow cannulae to achieve enhanced haemodynamic performance, reduced incidence of suction events, reduced levels of postoperative bleeding and a faster implantation procedure. Specific objectives were: * in-vitro evaluation of LVAD and RVAD inflow cannula placement, * design and in-vitro evaluation of a passive mechanism to reduce the potential for heart chamber suction, * design and in-vitro evaluation of a novel suture-less cannula fixation device. In order to complete in-vitro evaluation of VAD inflow cannulae, a mock circulation loop (MCL) was developed to accurately replicate the haemodynamics in the human systemic and pulmonary circulations. Validation of the MCL’s haemodynamic performance, including the form and magnitude of pressure, flow and volume traces was completed through comparisons of patient data and the literature. The MCL was capable of reproducing almost any healthy or pathological condition, and provided a useful tool to evaluate VAD cannulation and other cardiovascular devices. The MCL was used to evaluate inflow cannula placement for rotary VAD support. Left and right atrial and ventricular cannulation sites were evaluated under conditions of mild and severe heart failure. With a view to long term LVAD support in the severe left heart failure condition, left ventricular inflow cannulation was preferred due to improved LVAD efficiency and reduced potential for thrombus formation. In the mild left heart failure condition, left atrial cannulation was preferred to provide an improved platform for myocardial recovery. Similar trends were observed with RVAD support, however to a lesser degree due to a smaller difference in right atrial and ventricular pressures. A compliant inflow cannula to prevent suction events was then developed and evaluated in the MCL. As rotary LVAD or RVAD preload was reduced, suction events occurred in all instances with a rigid inflow cannula. Addition of the compliant segment eliminated suction events in all instances. This was due to passive restriction of the compliant segment as preload dropped, thus increasing the VAD circuit resistance and decreasing the VAD flow rate. Therefore, the compliant inflow cannula acted as a passive flow control / anti-suction system in LVAD and RVAD support. A novel suture-less inflow cannula fixation device was then developed to reduce implantation time and postoperative bleeding. The fixation device was evaluated for LVAD and RVAD support in cadaveric animal and human hearts attached to a MCL. LVAD inflow cannulation was achieved in under two minutes with the suture-less fixation device. No leakage through the suture-less fixation device – myocardial interface was noted. Continued development and in-vivo evaluation of this device may result in an improved inflow cannulation technique with the potential for off-bypass insertion. Continued development of this research, in particular the compliant inflow cannula and suture-less inflow cannulation device, will result in improved postoperative outcomes, life span and quality of life for end-stage heart failure patients.

BWW ontology as a lens on IS design theory: Extending the design science research roadmap

The Design Science Research Roadmap (DSR-Roadmap) [1] aims to give detailed methodological guidance to novice researchers in Information Systems (IS) DSR. Focus group evaluation, one phase of the overall study, of the evolving DSR-Roadmap revealed that a key difficulty faced by both novice and expert researchers in DSR, is abstracting design theory from design. This paper explores the extension of the DSR-Roadmap by employing IS deep structure ontology (BWW [2-4]) as a lens on IS design to firstly yield generalisable design theory, specifically 'IS Design Theory' (ISDT) elements [5]. Consideration is next given to the value of BWW in the application of the design theory by practitioners. Results of mapping BWW constructs to ISDT elements suggest that the BWW is promising as a common language between design researchers and practitioners, facilitating both design theory and design implementation

Sustainable and affordable housing : a myth or reality

The Australian government has released a draft National Building Framework that will likely tighten the building standard for new houses to meet higher sustainability requirements. There are uncertainties about the impact this could have on the cost of housing and the supply of affordable housing. This paper aims to provide evidence-based conclusions on the possibility of delivering sustainable and affordable housing for low income people. The case studies are gathered from Brisbane and Gold Coast. Case studies are analysed by unpacking the features that were included to meet sustainability and affordability goals for housing. This paper outlines the key factors for their success and also challenges for replication of the projects. The study shows that the key success drivers for delivering sustainable and affordable housing are providing planning incentives, subsidies for increased energy efficiency, supportive regulatory frameworks and appropriate allocation of infrastructure charges. It shows that government can prioritise their resources to support affordable and sustainable housing for low income people.

Analyzing and defining information requirements of knowledge intensive construction management tasks on BIM

With the increasing popularity and adoption of building information modeling (BIM), the amount of digital information available about a building is overwhelming. Enormous challenges remain however in identifying meaningful and required information from a complex BIM model to support a particular construction management (CM) task. Detailed specifications of information required by different construction domains and expressive and easy-to-use BIM reasoning mechanisms are seen as an important means in addressing these challenges. This paper analyzes some of the characteristics and requirements of component-specific construction knowledge in relation to the current work practice and BIM-based applications. It is argued that domain ontologies and information extraction approaches, such as queries could significantly bring much needed support for knowledge sharing and integration of information between design, construction and facility management.

Children and young people using public space : models of rights, optimism and wellbeing

This presentation discusses topics and issues that connect closely with the Conference Themes and themes in the ARACY Report Card. For example, developing models of public space that are safe, welcoming and relevant to children and young people will impact on their overall wellbeing and may help to prevent many of the tensions occurring in Australia and elsewhere around the world. This area is the subject of ongoing international debate, research and policy formation, relevant to concerns in the ARACY Report Card about children and young people’s health and safety, participation, behaviours and risks and peer and family relationships.

Write vs. type : tangible and situated media for situated engagement

Digital media is often criticised for being intangible, transient and ephemeral. These characteristics limit the provision of long-lasting social experiences, as it is through the use of all our senses that we attach meaning to space, creating a sense of place. This paper presents a comparative study of the affordances of two design interventions, one tangible paper-based, called Print + Talk = Love (PTL), the other digital screen-based, called Discussions in Space (DIS). The emphasis is on a) how tangible media, such as paper, provides different and meaningful collective experiences, and b) how it can stand on its own as an interactive design intervention and as a comprehensive data-gathering tool in urban public places. By positioning PTL and DIS within the context of urban public places and testing their abilities to engage participants, we examine their particular situated engagement abilities through a mixed method approach. As a result, the digital aspects of DIS, e.g., using Twitter, extend the situated experience beyond the actual location of the intervention. Moreover, informing a hybrid approach, we also found that the physical aspects of PTL and its tangible presence, kept the user experience focused on the actual place and event surrounding the intervention.

Hybrid place : blurring the edge between the digital and physical layers of urban environments

The purpose of this paper is to investigate the edge condition between the digital layers and the physical layers of the city and how tangible expressions of the interrelationships between them to create and define new experiences of place, creating hybrid place. To date there has been discussion and investigation into understanding the importance of place, similarly into defining hybrid space. This paper explores principles of place and space to question how they can be applied into defining and proposing the notion of hybrid place in urban environments. The integration of media spaces into architecture provide infrastructure for the development of hybrid place. The physical boundaries of urban spaces become blurred through the integration of media such as computer technologies connecting the physical environment with the digital. Literature and case studies that reflect the current trends of use of technology by people in space and place within urban environments are examined.

Passenger familiarity and intuitive navigation within airport environments

Passengers navigating through airports can experience confusion or become lost, resulting in dissatisfaction, missed flights and flight delays. Passengers moving through airports are required to make many navigation decisions, for example to find the correct check-in desk or find the correct boarding gate. Prior experience of using the airports is likely to enable intuitive navigation, however limited research on this topic currently exists. In this paper we investigate passenger navigation by observing 30 participants at one international airport as they moved from check-in to a departure gate. The results indicate that passengers do spend time navigating intuitively through the airport, and that there is a positive correlation between intuitive navigation and airport familiarity. It was also found that participants with lower airport familiarity spend a greater percentage of overall navigation time searching and assessing/acquiring information than high familiarity participants. These findings provide evidence that passengers with higher airport familiarity have a greater understanding of the process, have a better understanding of what information to look for and use this familiarity to navigate intuitively. Findings from this research will have design implications for both current, and future airport terminals and other large spaces that people navigate through.

Gestural, emergent and expressive : three research themes for haptic interaction

Drawing on three case studies of work in the fields of participatory design, interaction design and electronic arts, we reflect on the implications of these studies for haptic interface research. We propose three themes: gestural; emergent; and expressive; as signposts for a program of research into haptic interaction that could point the way towards novel approaches to haptic interaction and move us from optic to haptic ways of seeing.

Endotoxins in indoor air and settled dust in primary schools in a subtropical climate

Endotoxins can significantly affect the air quality in school environments. However, there is currently no reliable method for the measurement of endotoxins and there is a lack of reference values for endotoxin concentrations to aid in the interpretation of measurement results in school settings. We benchmarked the “baseline” range of endotoxin concentration in indoor air, together with endotoxin load in floor dust, and evaluated the correlation between endotoxin levels in indoor air and settled dust, as well as the effects of temperature and humidity on these levels in subtropical school settings. Bayesian hierarchical modeling indicated that the concentration in indoor air and the load in floor dust were generally (<95th percentile) < 13 EU/m3 and < 24,570 EU/m2, respectively. Exceeding these levels would indicate abnormal sources of endotoxins in the school environment, and the need for further investigation. Metaregression indicated no relationship between endotoxin concentration and load, which points to the necessity for measuring endotoxin levels in both the air and settled dust. Temperature increases were associated with lower concentrations in indoor air and higher loads in floor dust. Higher levels of humidity may be associated with lower airborne endotoxin concentrations.

Science and engineering for whole of life : integrating education, research and public engagement in a collaborative environment

Policy makers increasingly recognise that an educated workforce with a high proportion of Science, Technology, Engineering and Mathematics (STEM) graduates is a pre-requisite to a knowledge-based, innovative economy. Over the past ten years, the proportion of first university degrees awarded in Australia in STEM fields is below the global average and continues to decrease from 22.2% in 2002 to 18.8% in 2010 [1]. These trends are mirrored by declines between 20% and 30% in the proportions of high school students enrolled in science or maths. These trends are not unique to Australia but their impact is of concern throughout the policy-making community. To redress these demographic trends, QUT embarked upon a long-term investment strategy to integrate education and research into the physical and virtual infrastructure of the campus, recognising that expectations of students change as rapidly as technology and learning practices change. To implement this strategy, physical infrastructure refurbishment/re-building is accompanied by upgraded technologies not only for learning but also for research. QUT’s vision for its city-based campuses is to create vibrant and attractive places to learn and research and to link strongly to the wider surrounding community. Over a five year period, physical infrastructure at the Gardens Point campus was substantially reconfigured in two key stages: (a) a >$50m refurbishment of heritage-listed buildings to encompass public, retail and social spaces, learning and teaching “test beds” and research laboratories and (b) destruction of five buildings to be replaced by a $230m, >40,000m2 Science and Engineering Centre designed to accommodate retail, recreation, services, education and research in an integrated, coordinated precinct. This landmark project is characterised by (i) self-evident, collaborative spaces for learning, research and social engagement, (ii) sustainable building practices and sustainable ongoing operation and; (iii) dynamic and mobile re-configuration of spaces or staffing to meet demand. Innovative spaces allow for transformative, cohort-driven learning and the collaborative use of space to prosecute joint class projects. Research laboratories are aggregated, centralised and “on display” to the public, students and staff. A major visualisation space – the largest multi-touch, multi-user facility constructed to date – is a centrepiece feature that focuses on demonstrating scientific and engineering principles or science oriented scenes at large scale (e.g. the Great Barrier Reef). Content on this visualisation facility is integrated with the regional school curricula and supports an in-house schools program for student and teacher engagement. Researchers are accommodated in a combined open-plan and office floor-space (80% open plan) to encourage interdisciplinary engagement and cross-fertilisation of skills, ideas and projects. This combination of spaces re-invigorates the on-campus experience, extends educational engagement across all ages and rapidly enhances research collaboration.

Liminal moments : designing, thinking and learning

This paper provides a contextual reflection for understanding best practice teaching to first year design students. The outcome (job) focused approach to higher education has lead to some unanticipated collateral damage for students, and in the case we discuss, has altered the students’ expectations of course delivery with specific implications and challenges for design educators. This tendency in educational delivery systems is further compounded by the distinct characteristics of Generation Y students within a classroom context. It is our belief that foundational design education must focus more on process than outcomes, and through this research with first year design students we analyse and raise questions relative to the curriculum for a Design and Creative Thinking course—in which students not only benefit from learning the theories and processes of design thinking, conceptualisation and creativity, but also are encouraged to see it as an essential tool for their education and development as designers. This study considers the challenges within a design environment; specifically, we address the need for process based learning in contrast to the outcome-focused approach taken by most students. The authors base their reflections on teaching design students at a university in Queensland, Australia.

Imagining in the spatial design process

This thesis aims to expand our understanding of imagining in the spatial design disciplines of architecture and interior design. More than three decades after Lawson’s statement, the matter of “what goes on in a designer’s head”, or imagining and mental problem solving remains just as mysterious and just as pertinent, possibly more so given the social and environmental challenges facing humankind. The lines on a page, the small perspective sketches, the connection of lines and scrawled notes and other clues help us understand what may be going on in the mind of the architect or designer. However, how designers know that space intimately before it is built is not greatly understood and articulated – even by designers themselves. There is a gap in the market in terms of informed exploration of the thinking that occurs during the design process, and how this is translated into physical outcomes. In other words, what do we see in our mind’s eye during the design process? This thesis explores design thinking and design process; what we ‘see’ when we draw, what we ‘see’ when we design.

Knowledge inquiry in the construction management domain through structured research process and methodology

Construction works are project-based and interdisciplinary. Many construction management (CM) problems are ill defined. The knowledge required to address such problems is not readily available and mostly tacit in nature. Moreover, the researchers, especially the students in the higher education, often face difficulty in defining the research problem, adopting an appropriate research process and methodology for designing and validating their research. This paper describes a ‘Horseshoe’ research process approach and its application to address a research problem of extracting construction-relevant information from a building information model (BIM). It describes the different steps of the process for understanding a problem, formulating appropriate research question/s, defining different research tasks, including a methodology for developing, implementing and validating the research. It is argued that a structure research approach and the use of mixed research methods would provide a sound basis for research design and validation in order to make contribution to existing knowledge.

"You’ve modelled and now what?" : Exploring determinants of process model re-use

Business process modelling as a practice and research field has received great attention over recent years. Organizations invest significantly into process modelling in terms of training, tools, capabilities and resources. The return on this investment is a function of process model re-use, which we define as the recurring use of process models to support organizational work tasks. While prior research has examined re-use as a design principle, we explore re-use as a behaviour, because evidence suggest that analysts’ re-use of process models is indeed limited. In this paper we develop a two-stage conceptualization of the key object-, behaviour- and socioorganization-centric factors explaining process model re-use behaviour. We propose a theoretical model and detail implications for its operationalization and measurement. Our study can provide significant benefits to our understanding of process modelling and process model use as key practices in analysis and design.