Bifurcations and chaos in single-roll natural convection with low Prandtl number

Convective flows of a small Prandtl number fluid contained in a two-dimensional cavity subject to a lateral thermal gradient are numerically studied by using different techniques. The aspect ratio (length to height) is kept at around 2. This value is found optimal to make the flow most unstable while keeping the basic single-roll structure. Two cases of thermal boundary conditions on the horizontal plates are considered: perfectly conducting and adiabatic. For increasing Rayleigh numbers we find a transition from steady flow to periodic oscillations through a supercritical Hopf bifurcation that maintains the centrosymmetry of the basic circulation. For a Rayleigh number of about ten times that of the Hopf bifurcation the system initiates a complex scenario of bifurcations. In the conductive case these include a quasiperiodic route to chaos. In the adiabatic one the dynamics is dominated by the interaction of two Neimark-Sacker bifurcations of the basic periodic solutions, leading to the stable coexistence of three incommensurate frequencies, and finally to chaos. In all cases, the complex time-dependent behavior does not break the basic, single-roll structure.

Three-dimensional aspects of fluid flows in channels. I. Meniscus and thin film regimes

We study the forced displacement of a fluid-fluid interface in a three-dimensional channel formed by two parallel solid plates. Using a lattice-Boltzmann method, we study situations in which a slip velocity arises from diffusion effects near the contact line. The difference between the slip and channel velocities determines whether the interface advances as a meniscus or a thin film of fluid is left adhered to the plates. We find that this effect is controlled by the capillary and Péclet numbers. We estimate the crossover from a meniscus to a thin film and find good agreement with numerical results. The penetration regime is examined in the steady state. We find that the occupation fraction of the advancing finger relative to the channel thickness is controlled by the capillary number and the viscosity contrast between the fluids. For high viscosity contrast, lattice-Boltzmann results agree with previous results. For zero viscosity contrast, we observe remarkably narrow fingers. The shape of the finger is found to be universal.

New experimental apparatus for the study of the Bénard-Rayleigh problem

A new experimental system to measure the equivalent thermal conductivity of a liquid with regard to the Bénard-Rayleigh problem was constructed. The liquid is enclosed within walls of polymethylmethacrylate between two copper plates in which there are thermocouples to measure the difference in temperature between the lower and upper surfaces of the layer of liquid. Heat flux is measured by means of a linear heat fluxmeter consisting of 204 thermocouples in series. The fluxmeter was calibrated and the linear relationship that exists between the heat flux and the emf generated was verified. The thermal conductivity of the polymethylmethacrylate employed was measured and measurements of the equivalent conductivity in cylindrical boundaries of two silicone oils were made. The critical value of the temperature difference and the contribution of the convective process to the transmission of heat were determined.

Soil losses from typic cambisols and red latosol as related to three erosive rainfall patterns

Rainfall erosivity is one of the main factors related to water erosion in the tropics. This work focused on relating soil loss from a typic dystrophic Tb Haplic Cambisol (CXbd) and a typic dystrophic Red Latosol (LVdf) to different patterns of natural erosive rainfall. The experimental plots of approximately 26 m² (3 x 8.67 m) consisted of a CXbd area with a 0.15 m m-1 slope and a LVdf area with 0.12 m m-1 slope, both delimited by galvanized plates. Drainpipes were installed at the lower part of these plots to collect runoff, interconnected with a Geib or multislot divisor. To calculate erosivity (EI30), rainfall data, recorded continuously at a weather station in Lavras, were used. The data of erosive rainfall events were measured (10 mm precipitation intervals, accuracy 0.2 mm, 24 h period, 20 min intervals), characterized as rainfall events with more than 10 mm precipitation, maximum intensity > 24 mm h-1 within 15 min, or kinetic energy > 3.6 MJ, which were used in this study to calculate the rainfall erosivity parameter, were classified according to the moment of peak precipitation intensity in advanced, intermediate and delayed patterns. Among the 139 erosive rainfall events with CXbd soil loss, 60 % were attributed to the advanced pattern, with a loss of 415.9 Mg ha-1, and total losses of 776.0 Mg ha-1. As for the LVdf, of the 93 erosive rainfall events with soil loss, 58 % were listed in the advanced pattern, with 37.8 Mg ha-1 soil loss and 50.9 Mg ha-1 of total soil loss. The greatest soil losses were observed in the advanced rain pattern, especially for the CXbd. From the Cambisol, the soil loss per rainfall event was greatest for the advanced pattern, being influenced by the low soil permeability.

Microstructure of highly oriented, hexagonal, boron nitride thin films grown on crystalline silicon by radio frequency plasma-assisted chemical vapor deposition

We present a high‐resolution electron microscopy study of the microstructure of boron nitride thin films grown on silicon (100) by radio‐frequency plasma‐assisted chemical vapor deposition using B2H6 (1% in H2) and NH3 gases. Well‐adhered boron nitride films grown on the grounded electrode show a highly oriented hexagonal structure with the c‐axis parallel to the substrate surface throughout the film, without any interfacial amorphous layer. We ascribed this textured growth to an etching effect of atomic hydrogen present in the gas discharge. In contrast, films grown on the powered electrode, with compressive stress induced by ion bombardment, show a multilayered structure as observed by other authors, composed of an amorphous layer, a hexagonal layer with the c‐axis parallel to the substrate surface and another layer oriented at random

Saccamoeba lacustris, sp. nov. (Amoebozoa: Lobosea: Hartmannellidae), a new lobose amoeba, parasitized by the novel chlamydia 'Candidatus Metachlamydia lacustris' (Chlamydiae: Parachlamydiaceae).

An amoeba isolated from an aquatic biotope, identified morphologically as Saccamoeba limax, was found harbouring mutualistic rod-shaped gram-negative bacteria. During their cultivation on agar plates, a coinfection also by lysis-inducing chlamydia-like organisms was found in some subpopulations of that amoeba. .Here we provide a molecular-based identification of both the amoeba host and the two bacterial endosymbionts. Analysis of the 18S rRNA gene revealed that this strain is the sister-group to Glaeseria, for which we proposed the name Saccamoeba lacustris. The rod-shaped endosymbiont was identified as a member of Variovorax paradoxus group (Comamonadaceae, Beta-Proteobacteria). No growth on bacteriological agars was recorded, hence this symbiont might be strictly intracellular. The chlamydia-like parasite was unable to infect Acanthamoeba and other amoebae in coculture, showing high host specificity. Phylogenetic analysis based on the 16S rDNA indicated that it is a new member of the family Parachlamydiaceae (order Chlamydiales), for which we proposed the name 'Candidatus Metachlamydia lacustris'.

Three-dimensional aspects of fluid flows in channels. I. Meniscus and thin film regimes

We study the forced displacement of a fluid-fluid interface in a three-dimensional channel formed by two parallel solid plates. Using a lattice-Boltzmann method, we study situations in which a slip velocity arises from diffusion effects near the contact line. The difference between the slip and channel velocities determines whether the interface advances as a meniscus or a thin film of fluid is left adhered to the plates. We find that this effect is controlled by the capillary and Péclet numbers. We estimate the crossover from a meniscus to a thin film and find good agreement with numerical results. The penetration regime is examined in the steady state. We find that the occupation fraction of the advancing finger relative to the channel thickness is controlled by the capillary number and the viscosity contrast between the fluids. For high viscosity contrast, lattice-Boltzmann results agree with previous results. For zero viscosity contrast, we observe remarkably narrow fingers. The shape of the finger is found to be universal.

Efficacious treatment of non-dermatophyte mould onychomycosis with topical amphotericin B.

BACKGROUND: Dermatophytes are the main cause of onychomycosis, but various non-dermatophyte moulds (NDMs) are often the infectious agents in abnormal nails. In particular, Fusarium spp. and other NDMs are mostly insensitive to standard onychomycosis treatment with topical agents as well as with oral terbinafine and itraconazole.¦OBJECTIVE: The aim of this work is to report the efficacy of a topical amphotericin B solution on NDM onychomycosis in a series of 8 patients resistant to multiple conventional topical and systemic treatments.¦METHODS: Treatment consisted in the application of an optimized amphotericin B solution once daily to the affected nails and surrounding tissue. No mechanical debridement or medications were allowed except for trimming excessively long nails or in some cases occasionally applying urea-based cream to soften thickened nail plates.¦RESULTS: Onychomycosis was clinically cured in all patients after a 12-month treatment. Mycological cure was obtained in all but 1 patient.¦CONCLUSIONS: Topical amphotericin B is an efficacious, safe, cheap and easy-to-apply treatment which should be considered as first-line therapy for NDM onychomycosis.

The effect of lattice defects on Hele-Shaw flow over an etched lattice

We examine the patterns formed by injecting nitrogen gas into the center of a horizontal, radial Hele-Shaw cell filled with paraffin oil. We use smooth plates and etched plates with lattices having different amounts of defects (010 %). In all cases, a quantitative measure of the pattern ramification shows a regular trend with injection rate and cell gap, such that the dimensionless perimeter scales with the dimensionless time. By adding defects to the lattice, we observe increased branching in the pattern morphologies. However, even in this case, the scaling behavior persists. Only the prefactor of the scaling function shows a dependence on the defect density. For different lattice defect densities, we examine the nature of the different morphology phases.

On the origin of the North Pacific arcs

We present a new hypothesis that relates global plate tectonics to the formation of marginal basins, island arcs, spreading ridges and arc-shaped mountain belts around the North Pacific Ocean. According to our model, the ellipsoidal-shaped Paleogene basins of the South China Sea, Parece-Vela Basin, Shikoku Basin, Sea of Japan and the Sea of Okhotsk in addition to those of the North American Cordillera can be attributed to the change in plate convergence direction at 42 Ma between the Indoaustralian and Eurasian plates. The new direction of convergence was parallel to the eastern continental margin of Asia and resulted in widespread extension perpendicular to this margin and to the western margin of North America. Both margins form part of a circle parallel to the Indoaustralian-Eurasian direction of convergence.

Spore germination and development of young mycelia in some Rhizopogon species

Spore germination in Rhizopogon abietis, R. luteolus, R. roseolus and R. villosulus was induced in the presence of Rhodotorula glutinis and activated charcoal, in agar medium (N6:5). In one R. roseolus sample, 51% of spores germinated within 35 days, allowing observation of the course of spore germination and the different developmental patterns of homokaryotic mycelia. In these plates, spores showed two times of germination. The spores that germinated early produced an apical germ tube. Later other spores germinated in proximity to young mycelium, by forming a germ vesicle. One of the hyphal growth patterns obtained (interruption-swelling-ramification) is similar to that reported for other fungi. With this technique for inducing spore germination, it is possible to obtain enough monosporic cultures to perform mating tests. Key words: Basidiomycotina, Hypogeous, Monosporic Cultures.

Preventing Cracking at Diaphragm/Plate Girder Connections in Steel Bridges, HR-393, 1998

Some of the Iowa Department of Transportation (Iowa DOT) continuous, steel, welded plate girder bridges have developed web cracking in the negative moment regions at the diaphragm connection plates. The cracks are due to out-of-plane bending of the web near the top flange of the girder. The out-of-plane bending occurs in the "web-gap", which is the portion of the girder web between (1) the top of the fillet welds attaching the diaphragm connection plate to the web and (2) the fillet welds attaching the flange to the web. A literature search indicated that four retrofit techniques have been suggested by other researchers to prevent or control this type of cracking. To eliminate the problem in new bridges, AASHTO specifications require a positive attachment between the connection plate and the top (tension) flange. Applying this requirement to existing bridges is expensive and difficult. The Iowa DOT has relied primarily on the hole-drilling technique to prevent crack extension once cracking has occurred; however, the literature indicates that hole-drilling alone may not be entirely effective in preventing crack extension. The objective of this research was to investigate experimentally a method proposed by the Iowa DOT to prevent cracking at the diaphragm/plate girder connection in steel bridges with X-type or K-type diaphragms. The method consists of loosening the bolts at some connections between the diaphragm diagonals and the connection plates. The investigation included selecting and testing five bridges: three with X-type diaphragms and two with K-type diaphragms. During 1996 and 1997, these bridges were instrumented using strain gages and displacement transducers to obtain the response at various locations before and after implementing the method. Bridges were subjected to loaded test trucks traveling in different lanes with speeds varying from crawl speed to 65 mph (104 km/h) to determine the effectiveness of the proposed method. The results of the study show that the effect of out-of-plane loading was confined to widths of approximately 4 in. (100 mm) on either side of the connection plates. Further, they demonstrate that the stresses in gaps with drilled holes were higher than those in gaps without cracks, implying that the drilling hole technique is not sufficient to prevent crack extension. The behavior of the web gaps in X-type diaphragm bridges was greatly enhanced by the proposed method as the stress range and out-of-plane distortion were reduced by at least 42% at the exterior girders. For bridges with K-type diaphragms, a similar trend was obtained. However, the stress range increased in one of the web gaps after implementing the proposed method. Other design aspects (wind, stability of compression flange, and lateral distribution of loads) must be considered when deciding whether to adopt the proposed method. Considering the results of this investigation, the proposed method can be implemented for X-type diaphragm bridges. Further research is recommended for K-type diaphragm bridges.

Label-free cytotoxicity screening assay by digital holographic microscopy.

Abstract We introduce a label-free technology based on digital holographic microscopy (DHM) with applicability for screening by imaging, and we demonstrate its capability for cytotoxicity assessment using mammalian living cells. For this first high content screening compatible application, we automatized a digital holographic microscope for image acquisition of cells using commercially available 96-well plates. Data generated through both label-free DHM imaging and fluorescence-based methods were in good agreement for cell viability identification and a Z'-factor close to 0.9 was determined, validating the robustness of DHM assay for phenotypic screening. Further, an excellent correlation was obtained between experimental cytotoxicity dose-response curves and known IC values for different toxic compounds. For comparable results, DHM has the major advantages of being label free and close to an order of magnitude faster than automated standard fluorescence microscopy.

In vitro emergence of rifampicin resistance in Propionibacterium acnes and molecular characterization of mutations in the rpoB gene.

OBJECTIVES: Activity of rifampicin against Propionibacterium acnes biofilms was recently demonstrated, but rifampicin resistance has not yet been described in this organism. We investigated the in vitro emergence of rifampicin resistance in P. acnes and characterized its molecular background. METHODS: P. acnes ATCC 11827 was used (MIC 0.007 mg/L). The mutation rate was determined by inoculation of 10(9) cfu of P. acnes on rifampicin-containing agar plates incubated anaerobically for 7 days. Progressive emergence of resistance was studied by serial exposure to increasing concentrations of rifampicin in 72 h cycles using a low (10(6) cfu/mL) and high (10(8) cfu/mL) inoculum. The stability of resistance was determined after three subcultures of rifampicin-resistant isolates on rifampicin-free agar. For resistant mutants, the whole rpoB gene was amplified, sequenced and compared with a P. acnes reference sequence (NC006085). RESULTS: P. acnes growth was observed on rifampicin-containing plates with mutation rates of 2 ± 1 cfu  ×  10(-9) (4096× MIC) and 12 ± 5 cfu  ×  10(-9) (4 × MIC). High-level rifampicin resistance emerged progressively after 4 (high inoculum) and 13 (low inoculum) cycles. In rifampicin-resistant isolates, the MIC remained >32 mg/L after three subcultures. Mutations were detected in clusters I (amino acids 418-444) and II (amino acids 471-486) of the rpoB gene after sequence alignment with a Staphylococcus aureus reference sequence (CAA45512). The five following substitutions were found: His-437 → Tyr, Ser-442 → Leu, Leu-444 → Ser, Ile-483 → Val and Ser-485 → Leu. CONCLUSION: The rifampicin MIC increased from highly susceptible to highly resistant values. The resistance remained stable and was associated with mutations in the rpoB gene. To our knowledge, this is the first report of the emergence of rifampicin resistance in P. acnes.