CNTs & graphene for field emission applications

This paper details the use of carbon nanotubes and graphene for key field emission applications. Herein we describe the growth of nanotubes and their optimization for use in electron microscopes, field emission displays and x-ray sources. We also present a novel edge-emitting graphene based structure for large area electron emission displays.

A highly conductive and transparent solution processed AZO/MWCNT nanocomposite

A solution processed aluminum-doped zinc oxide (AZO)/multi-walled carbon nanotube (MWCNT) nanocomposite thin film has been developed offering simultaneously high optical transparency and low electrical resistivity, with a conductivity figure of merit (σDC/σopt) of ~75-better than PEDOT:PSS and many graphene derivatives. The reduction in sheet resistance of thin films of pristine MWCNTs is attributed to an increase in the conduction pathways within the sol-gel derived AZO matrix and reduced inter-MWCNT contact resistance. Films have been extensively characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), X-ray diffractometry (XRD), photoluminescence (PL), and ultraviolet-visible (UV-vis) spectroscopy. © 2013 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Graphene SOI CMOS sensors for detection of PPB levels of NO2 in air

There is considerable demand for sensors that are capable of detecting ultra-low concentrations (sub-PPM) of toxic gases in air. Of particular interest are NO2 and CO that are exhaust products of internal combustion engines. Electrochemical (EC) sensors are widely used to detect these gases and offer the advantages of low power, good selectivity and temporal stability. However, EC sensors are large (1 cm3), hand-made and thus expensive ($25). Consequently, they are unsuitable for the low-cost automotive market that demands units for less than $10. One alternative technology is SnO2 or WO3 resistive gas sensors that are fabricated in volume today using screen-printed films on alumina substrates and operate at 400°C. Unfortunately, they suffer from several disadvantages: power consumption is high 200 mW; reproducibility of the sensing element is poor; and cross-sensitivity is high. © 2013 IEEE.

Fridericia liangi sp nov (Enchytraeidae, Oligochaeta) from Changbaishan Mountain, China

We describe one new enchytraeid species, Fridericia liangi sp. nov., from Mt. Changbaishan, Jilin Province, northeastern China. It was collected from soils at the foot of Changbaishan Mountain and is distinguished from all known congeners by the following combination of characters: 1) no lateral chaetae, only ventral chaetae throughout, 2) a maximum of four chaetae in ventral preclitellar bundles, 3) one chaeta in ventral postclitellar bundles, 4) dorsal pores from VII on, 5) esophageal appendages unbranched, 6) coelomocytes without refractile vesicles, 7) clitellum girdle shaped, well developed, 8) no subneural glands, and 9) spermathecae simple.

Reversible CO2 absorption by the 6H perovskite Ba 4Sb2O9

A novel compound for carbon capture and storage (CCS) applications, the 6H perovskite Ba4Sb2O9, was found to be able to absorb CO2 through a chemical reaction at 873 K to form barium carbonate and BaSb2O6. This absorption was shown to be reversible through the regeneration of the original Ba4Sb 2O9 material upon heating above 1223 K accompanied by the release of CO2. A combined synchrotron X-ray diffraction, thermogravimetric, and microscopy study was carried out to characterize first the physical absorption properties and then to analyze the structural evolution and formation of phases in situ. Importantly, through subsequent carbonation and regeneration of the material over 100 times, it was shown that the combined absorption and regeneration reactions proceed without any significant reduction in the CO2 absorption capacity of the material. After 100 cycles the capacity of Ba4Sb2O9 was ∼0.1 g (CO 2)/g (sorbent), representing 73% of the total molar capacity. This is the first report of a perovskite-type material showing such good properties, opening the way for studies of new classes of inorganic oxide materials with stable and flexible chemical compositions and structures for applications in carbon capture. © 2013 American Chemical Society.

Speciation and Phylogeography of Opsariichthys bidens (Pisces: Cypriniformes: Cyprinidae) in China: Analysis of the Cytochrome b Gene of mtDNA from Diverse Populations

Gao-Yan Li, Xu-Zhen Wang, Ya-Hui Zhao, Jie Zhang, Chun-Guang Zhang, and Shun-Ping He (2009) Speciation and phylogeography of Opsariichthys bidens (Pisces: Cypriniformes: Cyprinidae) in China: analysis of the cytochrome b gene of mtDNA from diverse populations. Zoological Studies 48(4): 569-583. The cyprinid fish Opsariichthys bidens Gunther is distributed in all major river systems of continental East Asia, and represents an attractive model for phylogeographic studies among cyprinid species or within a given species. In this study, we investigated the phylogeographic and demographic history of this species, using partial sequences of the cytochrome (cyt) b gene in mitochondrial (mt)DNA. Fish samples were collected from almost all major river systems where O. bidens is distributed in China. Sequence analysis showed remarkably high polymorphism, with 125 haplotypes in the 234 specimens examined, and with 89.8% of haplotypes occurring in only 1 specimen. A neutrality test indicated that some groups were not at mutation-drift equilibrium, suggesting a past population expansion. These results were supported by a mismatch distribution analysis. Based on our analysis, O. bidens consists of 4 groups belonging to 2 clades. The divergence time of the 2 clades was estimated to be 11.06-8.04 my. This value corresponds to the time of the 2nd uplift of the Qinghai-Tibet Plateau, the emergence of the East Asian monsoon, and the Epoch-6 Event. A two species scheme is proposed. http://zoolstud.sinica.edu.tw/Journals/48.4/569.pdf

Field emission characteristics of contact printed graphene fins.

Carbon nanostructures have been much sought after for cold-cathode field emission applications. Herein a printing technique is reported to controllably nanostructure chemical vapor deposited graphene into vertically standing fins. The method allows for the creation of regular arrays of bilayer graphene fins, with sharp ridges that, when printed onto gold electrodes, afford a new type of field emission electron source geometry. The approach affords tunable morphologies and excellent long term and cyclic stabilities.

Modeling the carbon nanofiber addressed liquid crystal microlens array from experimentally observed optical phenomena

This paper presents a novel method of using experimentally observed optical phenomena to reverse-engineer a model of the carbon nanofiber-addressed liquid crystal microlens array (C-MLA) using Zemax. It presents the first images of the optical profile for the C-MLA along the optic axis. The first working optical models of the C-MLA have been developed by matching the simulation results to the experimental results. This approach bypasses the need to know the exact carbon nanofiber-liquid crystal interaction and can be easily adapted to other systems where the nature of an optical device is unknown. Results show that the C-MLA behaves like a simple lensing system at 0.060-0.276 V/μm. In this lensing mode the C-MLA is successfully modeled as a reflective convex lens array intersecting with a flat reflective plane. The C-MLA at these field strengths exhibits characteristics of mostly spherical or low order aspheric arrays, with some aspects of high power aspherics. It also exhibits properties associated with varying lens apertures and strengths, which concur with previously theorized models based on E-field patterns. This work uniquely provides evidence demonstrating an apparent "rippling" of the liquid crystal texture at low field strengths, which were successfully reproduced using rippled Gaussian-like lens profiles. © 2014 Published by Elsevier B.V.

Metallothionein-2 gene from the mandarin fish Siniperca chuatsi: cDNA cloning, tissue expression, and immunohistochemical localization

The metallothionein-2 (MT-2) gene was isolated from the mandarin fish, one of the most important industrial aquatic animals in China, by using rapid amplification of cDNA ends (RACE). The deduced amino acid sequence of MT-2 comprised 60 amino acids and showed approximately 62.3% identity to human metallothionein. Its promoter region was amplified by thermal asymmetric interlaced polymerase chain reaction (TAIL-PCR). The MT-2 gene consists of 3 exons and 2 introns, extending approximately 900 bp of genomic sequence. Phylogenetic analysis clearly demonstrated that MT-2 formed a clade with fish metallothionein. The promoter region contained 5 putative metal-regulatory elements (MREs) and 1 TATA box. Real-time quantitative RT-PCR analysis revealed that MT-2 transcripts were significantly increased in the brain and gills and were stable in the muscles, liver, and trunk kidney in Cd2+-stimulated fish. Western blotting analysis demonstrated that the protein of the MT-2 gene was expressed mainly in the gills, liver, heart, trunk kidney, muscle, and intestine; it was weakly detected in the brain and head kidney. Moreover, the MT-2 protein was immunohistochemically detected in the cytoplasm in the liver and trunk kidney. All the above results revealed that the mandarin fish MT-2 would be a useful biomarker for metal pollution. (C) 2008 Published by Elsevier Inc.

Enhanced protection against oxidative stress in an astaxanthin-overproduction Haematococcus mutant (Chlorophyceae)

Many unicellular green algae can become yellow or red in various natural habitats due to mass accumulation of a secondary carotenoid, such as lutein, or astaxanthin. The accumulation of secondary carotenoids is generally thought to be a survival strategy of the algae under photo-oxidative stress or other adverse environmental conditions. The physiological role of the carotenoids in stress response is less well understood at the subcellular or molecular level. In this study, a stable astaxanthin overproduction mutant (MT 2877) was isolated by chemical mutagenesis of a wild type (WT) of the green microalga Haematococcus pluvialis Flotow NIES-144. MT 2877 was identical to the WT with respect to morphology, pigment composition, and growth kinetics during the early vegetative stage of the life cycle. However, it had the ability to synthesize and accumulate about twice the astaxanthin content of the WT under high light, or under high light in the presence of excess amounts of ferrous sulphate and sodium acetate. Under stress, the mutant exhibited higher photosynthetic activities than the WT, based on considerably higher chlorophyll fluorescence induction, chlorophyll autofluorescence intensities, and oxygen evolution rates. Cell mortality caused by stress was reduced by half in the mutant culture compared with the WT. Enhanced protection of the mutant against stress is attributed to its accelerated carotenogenesis and accumulation of astaxanthin. Our results suggest that MT 2877, or other astaxanthin overproduction Haematococcus mutants, may offer dual benefits, as compared with the wild type, by increasing cellular astaxanthin content while reducing cell mortality during stress-induced carotenogenesis.

Cloning, characterization, and gene expression analysis of a novel cadmium metallothionein gene in Tetrahymena pigmentosa

A novel cadmium-inducible metallothionein (MT) gene (Tpig-MT1) was cloned and sequenced from the ciliate Tetrahymena pigmentosa. The number of deduced amino acids is 118. The polypeptide possesses CCC and CC clusters characteristic of typical Tetrahymena Cd-inducible MTs. The structure of Tpig-MT1 is different from the reported Cd-MT in T. pyriformis, T. thermophila and T. pigmentosa. Tpig-MT1 contains two intragenic tandem repeats with 72.9% identity described as Tpig-MT1 (repeat A1) and Tpig-MT1 (repeat A2). The transcriptional response of Tpig-MT1 gene to different heavy metals (Cd, Cu, Zn, Hg, Pb) and oxidative stress (H2O2) was measured using real-time quantitative PCR. The results showed that the gene was quickly induced (1 h) by the five heavy metals and the order of expression level was Hg>Pb>Cd>Cu>Zn. The induction effect of H2O2 was 5-fold after about 15 min, but soon decreased to a non-significant level (30 min). The genetic diversity of Tetrahymena MT genes is discussed in relation to the unique structure of the Tpig-MT1 gene and other reported Cd-MT isoforms. (C) 2008 Elsevier B.V. All rights reserved.

In-Situ grown carbon nanotubes for enhanced CO2 detection in non-dispersive-infra-red system

Non-dispersive-infra-red (NDIR) sensors are believed to be one of the most selective and robust solutions for CO2 detection, though cost prohibits their broader integration. In this paper we propose a commercially viable silicon-on-insulator (SOI) complementary metal-oxide (CMOS) micro-electro-mechanical (MEMS) technology for an IR thermal emitter. For the first time, vertically aligned multi walled carbon nanotubes (VA-MWCNTs) are suggested as a possible coating for the enhancement of the emission intensity of the optical source of a NDIR system. VA-MWCNTs have been grown in situ by chemical vapour deposition (CVD) exclusively on the heater area. Optical microscopy, scanning electron microscopy and Raman spectroscopy have been used to verify the quality of the VA-MWCNTs growth. The CNT-coated emitter demonstrated an increased response to CO2 of approx. 60%. Furthermore, we show that the VA-MWCNTs are stable up to temperatures of 500°C for up to 100 hours. © 2013 IEEE.

Experimental demonstration of a transparent graphene millimetre wave absorber with 28% fractional bandwidth at 140 GHz.

The development of transparent radio-frequency electronics has been limited, until recently, by the lack of suitable materials. Naturally thin and transparent graphene may lead to disruptive innovations in such applications. Here, we realize optically transparent broadband absorbers operating in the millimetre wave regime achieved by stacking graphene bearing quartz substrates on a ground plate. Broadband absorption is a result of mutually coupled Fabry-Perot resonators represented by each graphene-quartz substrate. An analytical model has been developed to predict the absorption performance and the angular dependence of the absorber. Using a repeated transfer-and-etch process, multilayer graphene was processed to control its surface resistivity. Millimetre wave reflectometer measurements of the stacked graphene-quartz absorbers demonstrated excellent broadband absorption of 90% with a 28% fractional bandwidth from 125-165 GHz. Our data suggests that the absorbers' operation can also be extended to microwave and low-terahertz bands with negligible loss in performance.

Multi-walled carbon nanotube conductivity enhancement and band gap widening via rapid pulsed thermal annealing

Herein we report on the transport characteristics of rapid pulsed vacuum-arc thermally annealed, individual and network multi-walled carbon nanotubes. Substantially reduced defect densities (by at least an order of magnitude), measured by micro-Raman spectroscopy, and were achieved by partial reconstruction of the bamboo-type defects during thermal pulsing compared with more traditional single-pulse thermal annealing. Rapid pulsed annealed processed networks and individual multi-walled nanotubes showed a consistent increase in conductivity (of over a factor of five at room temperature), attributed to the reduced number density of resistive axial interfaces and, in the case of network samples, the possible formation of structural bonds between crossed nanotubes. Compared to the highly defective as-grown nanotubes, the pulsed annealed samples exhibited reduced temperature sensitivity in their transport characteristics signifying the dominance of scattering events from structural defects. Transport measurements in the annealed multi-walled nanotubes deviated from linear Ohmic, typically metallic, behavior to an increasingly semiconducting-like behavior attributed to thermally induced axial strains. Rapid pulsed annealed networks had an estimated band gap of 11.26 meV (as-grown; 6.17 meV), and this observed band gap enhancement was inherently more pronounced for individual nanotubes compared with the networks most likely attributed to mechanical pinning effect of the probing electrodes which possibly amplifies the strain induced band gap. In all instances the estimated room temperature band gaps increased by a factor of two. The gating performance of back-gated thin-film transistor structures verified that the observed weak semiconductivity (p-type) inferred from the transport characteristic at room temperature. © 2014 Copyright Taylor & Francis Group, LLC.

Highly electron transparent Graphene for field emission triode gates

The enhanced emission performance of a graphene/Mo hybrid gate electrode integrated into a nanocarbon field emission micro-triode electron source is presented. Highly electron transparent gate electrodes are fabricated from chemical vapor deposited bilayer graphene transferred to Mo grids with experimental and simulated data, showing that liberated electrons efficiently traverse multi-layer graphene membranes with transparencies in excess of 50-68%. The graphene hybrid gates are shown to reduce the gate driving voltage by 1.1 kV, whilst increasing the electron transmission efficiency of the gate electrode significantly. Integrated intensity maps show that the electron beam angular dispersion is dramatically improved (87.9°) coupled with a 63% reduction in beam diameter. Impressive temporal stability is noted (<1.0%) with surprising negligible long-term damage to the graphene. A 34% increase in triode perveance and an amplification factor 7.6 times that of conventional refractory metal grid gate electrode-based triodes are noted, thus demonstrating the excellent stability and suitability of graphene gates in micro-triode electron sources. A nanocarbon field emission triode with a hybrid gate electrode is developed. The graphene/Mo gate shows a high electron transparency (50-68%) which results in a reduced turn-on potential, increased beam collimation, reduced beam diameter (63%), enhanced stability (<1% variation), a 34% increase in perveance, and an amplification 7.6 times that of equivalent conventional refractory metal gate triodes. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.