Inter- and intralaboratory variation of in vitro diffusion cell measurements: An international multicenter study using quasi-standardized methods and materials

In vitro measurements of skin absorption are an increasingly important aspect of regulatory studies, product support claims, and formulation screening. However, such measurements are significantly affected by skin variability. The purpose of this study was to determine inter- and intralaboratory variation in diffusion cell measurements caused by factors other than skin. This was attained through the use of an artificial (silicone rubber) rate-limiting membrane and the provision of materials including a standard penetrant, methyl paraben (MP), and a minimally prescriptive protocol to each of the 18 participating laboratories. Standardized calculations of MP flux were determined from the data submitted by each laboratory by applying a predefined mathematical model. This was deemed necessary to eliminate any interlaboratory variation caused by different methods of flux calculations. Average fluxes of MP calculated and reported by each laboratory (60 +/- 27 mug cm(-2) h(-1), n = 25, range 27-101) were in agreement with the standardized calculations of MP flux (60 +/- 21 mug cm(-2) h(-1), range 19-120). The coefficient of variation between laboratories was approximately 35% and was manifest as a fourfold difference between the lowest and highest average flux values and a sixfold difference between the lowest and highest individual flux values. Intra-laboratory variation was lower, averaging 10% for five individuals using the same equipment within a single laboratory. Further studies should be performed to clarify the exact components responsible for nonskin-related variability in diffusion cell measurements. It is clear that further developments of in vitro methodologies for measuring skin absorption are required. (C) 2005 Wiley-Liss, Inc.

Suicide inhibition of acetohydroxyacid synthase by hydroxypyruvate

Acetohydroxyacid synthase (Ec 2.2.1.6) catalyses the thiamine diphosphate-dependent reaction between two molecules of pyruvate yielding 2-acetolactacte and CO2. The enzyme will also utilise hydroxypyruvate with a k(cat) value that is 12% of that observed with pyruvate. When hydroxypyruvate is the substrate, the enzyme undergoes progressive inactivation with kinetics that are characteristic of suicide inhibition. It is proposed that the dihydroxyethyl-thiamine diphosphate intermediate can expel a hydroxide ion forming an enol that rearranges to a bound acetyl group.

Impact of specialised first-episode psychosis treatment on suicide following initial presentation to mental health services: Retrospective cohort study

Background: Suicide risk in psychosis peaks early in the course, however little is known about the effect on rates of suicide of specialised first-episode psychosis (FEP) programs.

The use of multivariate methods in the identification of subtypes of Alzheimer's disease: a comparison of principal components and cluster analysis

Two contrasting multivariate statistical methods, viz., principal components analysis (PCA) and cluster analysis were applied to the study of neuropathological variations between cases of Alzheimer's disease (AD). To compare the two methods, 78 cases of AD were analyzed, each characterised by measurements of 47 neuropathological variables. Both methods of analysis revealed significant variations between AD cases. These variations were related primarily to differences in the distribution and abundance of senile plaques (SP) and neurofibrillary tangles (NFT) in the brain. Cluster analysis classified the majority of AD cases into five groups which could represent subtypes of AD. However, PCA suggested that variation between cases was more continuous with no distinct subtypes. Hence, PCA may be a more appropriate method than cluster analysis in the study of neuropathological variations between AD cases.

Differential patterns of activity and functional connectivity in emotion processing neural circuitry to angry and happy faces in adolescents with and without suicide attempt

Background - Neural substrates of emotion dysregulation in adolescent suicide attempters remain unexamined. Method - We used functional magnetic resonance imaging to measure neural activity to neutral, mild or intense (i.e. 0%, 50% or 100% intensity) emotion face morphs in two separate emotion-processing runs (angry and happy) in three adolescent groups: (1) history of suicide attempt and depression (ATT, n = 14); (2) history of depression alone (NAT, n = 15); and (3) healthy controls (HC, n = 15). Post-hoc analyses were conducted on interactions from 3 group × 3 condition (intensities) whole-brain analyses (p < 0.05, corrected) for each emotion run. Results - To 50% intensity angry faces, ATT showed significantly greater activity than NAT in anterior cingulate gyral–dorsolateral prefrontal cortical attentional control circuitry, primary sensory and temporal cortices; and significantly greater activity than HC in the primary sensory cortex, while NAT had significantly lower activity than HC in the anterior cingulate gyrus and ventromedial prefrontal cortex. To neutral faces during the angry emotion-processing run, ATT had significantly lower activity than NAT in the fusiform gyrus. ATT also showed significantly lower activity than HC to 100% intensity happy faces in the primary sensory cortex, and to neutral faces in the happy run in the anterior cingulate and left medial frontal gyri (all p < 0.006,corrected). Psychophysiological interaction analyses revealed significantly reduced anterior cingulate gyral–insula functional connectivity to 50% intensity angry faces in ATT v. NAT or HC. Conclusions - Elevated activity in attention control circuitry, and reduced anterior cingulate gyral–insula functional connectivity, to 50% intensity angry faces in ATT than other groups suggest that ATT may show inefficient recruitment of attentional control neural circuitry when regulating attention to mild intensity angry faces, which may represent a potential biological marker for suicide risk.

Investigating the Relations of Attacks, Methods and Objects in Regard to Information Security in Network TCP/IP Environment

Possibilities for investigations of 43 varieties of file formats (objects), joined in 10 groups; 89 information attacks, joined in 33 groups and 73 methods of compression, joined in 10 groups are described in the paper. Experimental, expert, possible and real relations between attacks’ groups, method’ groups and objects’ groups are determined by means of matrix transformations and the respective maximum and potential sets are defined. At the end assessments and conclusions for future investigation are proposed.

Reasoning Methods for Designing and Surveying Relationships Described by Sets of Functional Constraints

This work is supported by the Hungarian Scientific Research Fund (OTKA), grant T042706.

Reliability analysis of encapsulation methods for lead -based paint through an accelerated life testing

The adverse health effects of long-term exposure to lead are well established, with major uptake into the human body occurring mainly through oral ingestion by young children. Lead-based paint was frequently used in homes built before 1978, particularly in inner-city areas. Minority populations experience the effects of lead poisoning disproportionately. ^ Lead-based paint abatement is costly. In the United States, residents of about 400,000 homes, occupied by 900,000 young children, lack the means to correct lead-based paint hazards. The magnitude of this problem demands research on affordable methods of hazard control. One method is encapsulation, defined as any covering or coating that acts as a permanent barrier between the lead-based paint surface and the environment. ^ Two encapsulants were tested for reliability and effective life span through an accelerated lifetime experiment that applied stresses exceeding those encountered under normal use conditions. The resulting time-to-failure data were used to extrapolate the failure time under conditions of normal use. Statistical analysis and models of the test data allow forecasting of long-term reliability relative to the 20-year encapsulation requirement. Typical housing material specimens simulating walls and doors coated with lead-based paint were overstressed before encapsulation. A second, un-aged set was also tested. Specimens were monitored after the stress test with a surface chemical testing pad to identify the presence of lead breaking through the encapsulant. ^ Graphical analysis proposed by Shapiro and Meeker and the general log-linear model developed by Cox were used to obtain results. Findings for the 80% reliability time to failure varied, with close to 21 years of life under normal use conditions for encapsulant A. The application of product A on the aged gypsum and aged wood substrates yielded slightly lower times. Encapsulant B had an 80% reliable life of 19.78 years. ^ This study reveals that encapsulation technologies can offer safe and effective control of lead-based paint hazards and may be less expensive than other options. The U.S. Department of Health and Human Services and the CDC are committed to eliminating childhood lead poisoning by 2010. This ambitious target is feasible, provided there is an efficient application of innovative technology, a goal to which this study aims to contribute. ^

A study of methods used to analyze total oil and polycyclic aromatic hydrocarbons in produced water: steps towards the validation of molecularly imprinted polymers for use in marine environmetns

Produced water is a by-product of offshore oil and gas production, and is released in large volumes when platforms are actively processing crude oil. Some pollutants are not typically removed by conventional oil/water separation methods and are discharged with produced water. Oil and grease can be found dispersed in produced water in the form of tiny droplets, and polycyclic aromatic hydrocarbons (PAHs) are commonly found dissolved in produced water. Both can have acute and chronic toxic effects in marine environments even at low exposure levels. The analysis of the dissolved and dispersed phases are a priority, but effort is required to meet the necessary detection limits. There are several methods for the analysis of produced water for dispersed oil and dissolved PAHs, all of which have advantages and disadvantages. In this work, EPA Method 1664 and APHA Method 5520 C for the determination of oil and grease will be examined and compared. For the detection of PAHs, EPA Method 525 and PAH MIPs will be compared, and results evaluated. APHA Method 5520 C Partition-Infrared Method is a liquid-liquid extraction procedure with IR determination of oil and grease. For analysis on spiked samples of artificial seawater, extraction efficiency ranged from 85 – 97%. Linearity was achieved in the range of 5 – 500 mg/L. This is a single-wavelength method and is unsuitable for quantification of aromatics and other compounds that lack sp³-hybridized carbon atoms. EPA Method 1664 is the liquid-liquid extraction of oil and grease from water samples followed by gravimetric determination. When distilled water spiked with reference oil was extracted by this procedure, extraction efficiency ranged from 28.4 – 86.2%, and %RSD ranged from 7.68 – 38.0%. EPA Method 525 uses solid phase extraction with analysis by GC-MS, and was performed on distilled water and water from St. John’s Harbour, all spiked with naphthalene, fluorene, phenanthrene, and pyrene. The limits of detection in harbour water were 0.144, 3.82, 0.119, and 0.153 g/L respectively. Linearity was obtained in the range of 0.5-10 g/L, and %RSD ranged from 0.36% (fluorene) to 46% (pyrene). Molecularly imprinted polymers (MIPs) are sorbent materials made selective by polymerizing functional monomers and crosslinkers in the presence of a template molecule, usually the analytes of interest or related compounds. They can adsorb and concentrate PAHs from aqueous environments and are combined with methods of analysis including GC-MS, LC-UV-Vis, and desorption electrospray ionization (DESI)- MS. This work examines MIP-based methods as well as those methods previously mentioned which are currently used by the oil and gas industry and government environmental agencies. MIPs are shown to give results consistent with other methods, and are a low-cost alternative improving ease, throughput, and sensitivity. PAH MIPs were used to determine naphthalene spiked into ASTM artificial seawater, as well as produced water from an offshore oil and gas operation. Linearity was achieved in the range studied (0.5 – 5 mg/L) for both matrices, with R² = 0.936 for seawater and R² = 0.819 for produced water. The %RSD for seawater ranged from 6.58 – 50.5% and for produced water, from 8.19 – 79.6%.

Factors associated with hospitalization after suicide spectrum behaviors: results from a multicentre study in Spain

Objectives: to identify factors associated with admission after suicide spectrum behaviors. Methods: Patient's characteristics, the nature of their suicidal behavior, admission rates between centres, and factors associated with admission have been examined in suicide spectrum presentations to emergency departments in three Spanish cities. Results: Intent of the suicidal behavior had the greatest impact on hospitalization. Older age, living alone, self-harm method not involving drug overdose, previous history of suicide spectrum behaviors and psychiatric diagnosis of schizophrenia, mood or personality disorder were independently associated with being admitted. There was a three-fold between-centre difference in the rate of hospitalization. Conclusions: widespread differences in the rate of hospitalization were primarily accounted for by characteristics of the individual patients and their suicidal behavior.

Mathematical methods for the configuration of transportation systems with a focus on continuous and modular matrix conveyors

The lack of flexibility in logistic systems currently on the market leads to the development of new innovative transportation systems. In order to find the optimal configuration of such a system depending on the current goal functions, for example minimization of transport times and maximization of the throughput, various mathematical methods of multi-criteria optimization are applicable. In this work, the concept of a complex transportation system is presented. Furthermore, the question of finding the optimal configuration of such a system through mathematical methods of optimization is considered.

Demographic trends in suicide in the UK and Ireland 1980 - 2010.

Background Ireland has the 17th highest suicide rate in the EU and the 4th highest among 15 to 24-year-old males (WHO 2012). Suicide is the leading cause of death in this age group; death by hanging accounted for 69 % of suicides in 2010. Methods This study examines youth suicide rates from 1980 to 2010 in Ireland and compares them to the rates in Northern Ireland, Scotland, England and Wales. Irish data were obtained from the Central Statistics Office and their annual reports on Vital Statistics. Northern Irish data were obtained from the Northern Ireland Statistics and Research Agency website; Scottish data were from the General Register Office for Scotland and English/Welsh data from the Office for National Statistics website. Results There has been a threefold increase in young male suicide in Ireland over the past three decades (8.9 - 29.7 per 100,000). In contrast, there has been approximately a threefold reduction in deaths by road traffic accidents in young men in the same period (42.7 - 16.2 per 100,000). Suicide rates in young men are similar in Scotland and Northern Ireland for the same period but are 50 % lower in England and Wales. Despite the rates of hanging as a method of suicide increasing in all jurisdictions, the overall rate in England and Wales has continued to decline. Conclusion The suicide rate in Ireland remains very high and strategies to address this are urgently required. Our study indicates that national suicide prevention strategies can be effective.

Understanding Suicide and Help-seeking in Urban and Rural Areas in Northern Ireland

Funded by HSC R&D Division, Public Health Agency Why did we start? Most people who complete suicide are in contact with their family doctors or other services in the months prior to death. A better understanding of the nature of these contacts and the various pathways experienced by suicidal people should reveal the gaps and barriers to effective service provision. We also need better information about the difficulties experienced by family carers, both prior to the death and afterwards. Of particular interest to policy makers in Northern Ireland was a concern that people from rural areas may be at increasing risk of suicide. We were commissioned by the Health and Social Care R&D Division of the Northern Ireland Public Health Agency to address the gaps in our understanding of suicide in NI. What did we do? We undertook a mixed methods study in which we examined the records of 403 people who took their own lives over a two-year period between March 2007 and February 2009. We linked these data to GP records and then examined help-seeking pathways of people and their contacts with services. We did in-depth face-to-face interviews with 72 bereaved relatives and friends who discussed their understanding of the events and circumstances surrounding the death, the experience of seeking help for the family member, the personal impact of the suicide, and use of support services. Additionally, we interviewed 19 General Practitioners about their experiences of managing people who died by suicide.            

Estimating the effect of state-level gun purchasing policy on county-level firearm suicide mortality

Thesis (Master's)--University of Washington, 2016-08

‘We report the world as it is, not as we want it to be’: Journalistic negotiation of news routines, roles and responsibilities when reporting on suicide

Thesis (Master's)--University of Washington, 2016-08