IMO technical and operational measures for reduction of emissions of greenhouse gas from ships : perspectives of Asian countries

International shipping is responsible for about 2.7% of the global emissions of CO2. In the absence of proper action, emissions from the maritime sector may grow by 150% to 250% by 2050, in comparison with the level of emissions in 2007. Against this backdrop, the International Maritime Organisation has introduced a mandatory Energy Efficiency Design Index (EEDI) for new ships and the Ship Energy Efficiency Management Plan (SEEMP) for all ships. Some Asian countries have voiced serious reservations about the newly adopted IMO regulations. They have suggested that imposing the same obligations on all countries, irrespective of their economic status, is a serious departure from the Principle of Common but Differentiated Responsibility, which has always been the cornerstone of international climate change law discourse. Against this backdrop, this article presents a brief overview of the technical and operational measures from the perspective of Asian countries.

Turbulence in an inundated urban environment during a major flood : implications in terms of people evacuation and sediment deposition

Floods through inundated urban environments constitute a hazard to the population and infrastructure. A series of field measurements were performed in an inundated section of the City of Brisbane (Australia) during a major flood in January 2011. Using an acoustic Doppler velocimeter (ADV), detailed velocity and suspended sediment concentration measurements were conducted about the peak of the flood. The results are discussed with a focus on the safety of individuals in floodwaters and the sediment deposition during the flood recession. The force of the floodwaters in Gardens Point Road was deemed unsafe for individual evacuation. A comparison with past laboratory results suggested that previous recommendations could be inappropriate and unsafe in real flood flows.

Vulnerability and damage analysis of reinforced concrete framed buildings subjected to near field blast events

Terrorists usually target high occupancy iconic and public buildings using vehicle borne incendiary devices in order to claim a maximum number of lives and cause extensive damage to public property. While initial casualties are due to direct shock by the explosion, collapse of structural elements may extensively increase the total figure. Most of these buildings have been or are built without consideration of their vulnerability to such events. Therefore, the vulnerability and residual capacity assessment of buildings to deliberately exploded bombs is important to provide mitigation strategies to protect the buildings' occupants and the property. Explosive loads and their effects on a building have therefore attracted significant attention in the recent past. Comprehensive and economical design strategies must be developed for future construction. This research investigates the response and damage of reinforced concrete (RC) framed buildings together with their load bearing key structural components to a near field blast event. Finite element method (FEM) based analysis was used to investigate the structural framing system and components for global stability, followed by a rigorous analysis of key structural components for damage evaluation using the codes SAP2000 and LS DYNA respectively. The research involved four important areas in structural engineering. They are blast load determination, numerical modelling with FEM techniques, material performance under high strain rate and non-linear dynamic structural analysis. The response and damage of a RC framed building for different blast load scenarios were investigated. The blast influence region for a two dimensional RC frame was investigated for different load conditions and identified the critical region for each loading case. Two types of design methods are recommended for RC columns to provide superior residual capacities. They are RC columns detailing with multi-layer steel reinforcement cages and a composite columns including a central structural steel core. These are to provide post blast gravity load resisting capacity compared to typical RC column against a catastrophic collapse. Overall, this research broadens the current knowledge of blast and residual capacity analysis of RC framed structures and recommends methods to evaluate and mitigate blast impact on key elements of multi-storey buildings.

From "Secondary Punishment" to "Supermax" : the human costs of high-security regimes in Australia

“Supermax” prisons, conceived by the United States in the early 1980s, are typically reserved for convicted political criminals such as terrorists and spies and for other inmates who are considered to pose a serious ongoing threat to the wider community, to the security of correctional institutions, or to the safety of other inmates. Prisoners are usually restricted to their cells for up to twenty-three hours a day and typically have minimal contact with other inmates and correctional staff. Not only does the Federal Bureau of Prisons operate one of these facilities, but almost every state has either a supermax wing or stand-alone supermax prison. The Globalization of Supermax Prisons examines why nine advanced industrialized countries have adopted the supermax prototype, paying particular attention to the economic, social, and political processes that have affected each state. Featuring essays that look at the U.S.-run prisons of Abu Ghraib and Guantanemo, this collection seeks to determine if the American model is the basis for the establishment of these facilities and considers such issues as the support or opposition to the building of a supermax and why opposition efforts failed; the allegation of human rights abuses within these prisons; and the extent to which the decision to build a supermax was influenced by developments in the United States. Additionally, contributors address such domestic matters as the role of crime rates, media sensationalism, and terrorism in each country’s decision to build a supermax prison.

A flexible optimisation model for the railway crew scheduling problem

Addressing the Crew Scheduling Problem (CSP) in transportation systems can be too complex to capture all details. The designed models usually ignore or simplify features which are difficult to formulate. This paper proposes an alternative formulation using a Mixed Integer Programming (MIP) approach to the problem. The optimisation model integrates the two phases of pairing generation and pairing optimisation by simultaneously sequencing trips into feasible duties and minimising total elapsed time of any duty. Crew scheduling constraints in which the crew have to return to their home depot at the end of the shift are included in the model. The flexibility of this model comes in the inclusion of the time interval of relief opportunities, allowing the crew to be relieved during a finite time interval. This will enhance the robustness of the schedule and provide a better representation of real-world conditions.

A derivation of high-frequency asymptotic values of 3D added mass and damping based on properties of the Cummins' equation

This brief paper provides a novel derivation of the known asymptotic values of three-dimensional (3D) added mass and damping of marine structures in waves. The derivation is based on the properties of the convolution terms in the Cummins's Equation as derived by Ogilvie. The new derivation is simple and no approximations or series expansions are made. The results follow directly from the relative degree and low-frequency asymptotic properties of the rational representation of the convolution terms in the frequency domain. As an application, the extrapolation of damping values at high frequencies for the computation of retardation functions is also discussed.

Control design for positioning of underwater vehicles with control allocation

In this paper, we address the control design problem of positioning of over-actuated underwater vehicles. The proposed design is based on a control architecture with combined position and velocity loops and a control tuning method based on the decoupled models. We derive analytical tuning rules based on requirements of closed-loop stability, positioning performance, and the vehicle velocity dynamic characteristics. The vehicle modelling is considered from force to motion with appropriate simplifications related to low-speed manoeuvring hydrodynamics and vehicle symmetry. The control design is considered together with a control allocation mapping. This approach makes the control tuning independent of the characteristics of the force actuators and provides the basis for control reconfiguration in the presence of actuator failure. We propose an anti-wind-up implementation of the controller, which ensures that the constraints related to actuation capacity are not violated. This approach simplifies the control allocation problem since the actuator constraints are mapped into generalised force constraints.

Proposed MBMs for reduction of greenhouse gas emissions from international shipping and the WTO rules

The international shipping sector is a major contributor to global greenhouse gas (GHG) emissions. The International Maritime Organisation (IMO) has adopted some technical and operational measures to reduce GHG emissions from international shipping. However, these measures may not be enough to reduce the amount of GHG emissions from international shipping to an acceptable level. Therefore, the IMO Member States are currently considering a number of proposals for the introduction of market-based measures (MBMs). During the negotiation process, some leading developing countries raised questions about the probable confl ict of the proposed MBMs with the rules of the World Trade Organisation (WTO). This article comprehensively examines this issue and argues that none of the MBM proposals currently under consideration by the IMO has any confl ict with the WTO rules.

Advances in gyro-stabilisation of vessel roll motion

The use of gyro-dynamic forces to counteract the wave-induced roll motion of marine vessels in a seaway was proposed over 100 years ago. These early systems showed a remarkable performance, reporting roll reductions of up to 95% in some sailing conditions. Despite this success, further developments were not pursued since the systems were unable to provide acceptable performance over an extended envelope of sailing and environmental conditions, and the invention of fin roll stabilisers provided a satisfactory alternative. This has been attributed to simplistic controls, heavy drive systems, and large structural mass required to withstand the loads given the low strength materials available at the time. Today, advances in material strength, bearings, motor technology and mechanical design methods, together with powerful signal processing algorithms, has resulted in a revitalized interest in gyro-stabilisers for ships. Advanced control systems have enabled optimisation of restoring torques across a range of wave environments and sailing conditions through adaptive control system design. All of these improvements have resulted in increased spinning speed, lower mass, and dramatically increased stabilising performance. This brief paper provides an overview of recent developments in the design and control of gyro-stabilisers of ship roll motion. In particular, the novel Halcyon Gyro-Stabilisers are introduced, and their performance is illustrated based on a simulation case study for a naval patrol vessel. Given the growing national and global interest in small combatants and patrol vessels, modem gyro-stabilisers may offer a significant technological contribution to the age old problem of comfort and mission operability on small ships, especially at loiter speeds.

A quay crane scheduling methodology for multimodal container terminals

This thesis develops an operational decision support tool for container terminal managements. The tool generates efficient schedules for shore cranes handling containers carried by mega container vessels.

Leaving family behind: Understanding the irregular migration of unaccompanied asylum-seeking minors - A qualitative study

This qualitative study investigated the drivers and determinants of irregular maritime migration among 17 protection visa holders who arrived in Australia as unaccompanied asylum-seeking minors. Semi-structured interviews were also conducted with eight non-government service providers working with unaccompanied minors in the Greater Brisbane area.

A magnetic climbing robot for marine inspection services

Currently, the inspection of sea-going vessels is performed manually. Ship surveyors do a visual inspection; in some cases they also use cameras and non-destructive testing methods. Prior to a ship surveying process a lot of scaffolding has to be provided in order to make every spot accessible for the surveyor. In this work a robotic system is presented, which is able to access many areas of a cargo hold of a ship and perform visual inspection without any scaffolding. The paper also describes how the position of the acquired data is estimated with an optical 3D tracking unit and how critical points on the hull can be marked via a remote controlled marker device. Furthermore first results of onboard tests with the system are provided.

Small firm training: Just meeting the day-to-day needs of the business

Purpose The purpose of this paper is to explore what the attitudes of small firm owner-managers are to developing the skills of their key resources and then examine how these and other factors affect owner-managers’ preferences for training these employees. Design/methodology/approach This study of training in small road transport firms in West Australia is cast in light of the literature on human resource management in small firms underpinned by insights drawn using the resource based view of the firm. Small firms (less than 20 people) dominate this industry, while the increasing freight task, and extreme distances between West Australian ports, towns and mines highlight this sectors’ importance. Survey results from 39 small road transport firms and interviews with nine owner-managers are analysed. Findings Legislative, regulatory and licensing requirements were shown to be a key determinant of skills development. Employers ensured that basic standards for employee certification and qualification were met, as the penalty for not doing so would be too high. Regulations drove the need for certain types of training – licenses, fatigue management, occupational health and safety, handling dangerous goods, the Maritime Security Identification Card card, forklift license, mine site inductions – while owner-managers knew where to get the training their staff needed. Although regulation appeared most visible in prescribing what happened in relation to training for drivers, the relevance of owner-managers’ attitudes could not be ignored, nor could conditions in the firms external environment as this shaped how these requirements were met. Research limitations/implications The RBV is useful in showing how skill development enabled similarity in skills across firms, while the attitudes owner-managers and economic and social conditions meant what happened in firms around skill development varied. The importance of small firm owner-managers’ attitudes are clearly highlighted and shown to influence organizational decisions and choices around training, but these were not independent of the regulatory framework and the economic and social conditions within which the firm operated. The small firms in this study did engage workers in formal training when necessary but it was put in the context of the idiosyncratic approach of the owner-manager and the day-to-day needs of the firm. “Training” was essentially about ensuring certain types of skills were held by employees and then passing on knowledge to ensure the behavior of employees was consistent with the owner-manager’s vision for the firm in its current environment. Originality/value Ways industry and government can encourage training activity that goes beyond the day-to-day firm needs are suggested.

Key opportunities for the future of roads to contribute to Australia's climate change response

Road agencies face growing pressure to respond to a range of issues associated with climate change and the reliance on fossil fuels. A key part of this response will be to reduce the dependency on fossil fuel based energy (and the associated greenhouse gas emissions) of transport, both vehicles and infrastructure. This paper presents findings of investigations into three key areas of innovative technologies and processes, namely the inclusion of onsite renewable energy generation technologies as part of road and transport infrastructure, the potential for automated motorways to reduce traffic fuel consumption (referred to as 'Smart Roads'), and the reduction of energy demand from route and signal lighting. The paper then concludes with the recommendation for the engineering profession to embrace sustainability performance assessment and rating tools as the basis for enhancing and communicating the contribution to Australia's response to climate change. Such tools provide a rigorous structure that can standardise approaches to key issues across entire sectors and provide clarity on the evidence required to demonstrate leading performance. The paper has been developed with funding and support provided by Australia's Sustainable Built Environment National Research Centre (SBEnrc), working with partners including Main Roads Western Australia, NSW Roads and Maritime Services, Queensland Department of Transport and Main Roads, John Holland Group, the Infrastructure Sustainability Council of Australia, Roads Australia, and the CRC for Low Carbon Living.

Merenkulun turvallisuuden koetinkiviä : Terminologisen tiedon poiminta teksteistä

The methodology of extracting information from texts has widely been described in the current literature. However, the methodology has been developed mainly for the purposes of other fields than terminology science. In addition, the research has been English language oriented. Therefore, there are no satisfactory language-independent methods for extracting terminological information from texts. The aim of the present study is to form the basis for a further improvement of methods for extraction of terminological information. A further aim is to determine differences in term extraction between subject groups with or without knowledge of the special field in question. The study is based on the theory of terminology, and has mainly a qualitative approach. The research material consists of electronically readable specialized texts in the subject domain of maritime safety. Textbooks, conference papers, research reports and articles from professional journals in Finnish and in Russian are included. The thesis first deals with certain term extraction methods. These are manual term identification and semi-automatic term extraction, the latter of which was carried out by using three commercial computer programs. The results of term extraction were compared and the recall and precision of the methods were evaluated. The latter part of the study is dedicated to the identification of concept relations. Certain linguistic expressions, which some researchers call knowledge probes, were applied to identify concept relations. The results of the present thesis suggest that special field knowledge is an advantage in manual term identification. However, in the candidate term lists the variation between subject groups was not as remarkable as it was between individual subjects. The term extraction software tested here produces candidate term lists which can be useful, but only after some manual work. Therefore, the work emphasizes the need to further develop term extraction software. Furthermore, the analyses indicate that there are a certain number of terms which were extracted by all the subjects and the software. These terms we call core terms. As the result of the experiment on linguistic expressions which signal concept relations, a proposal of Finnish and Russian knowledge probes in the field of maritime safety was made. The main finding was that it would be useful to combine the use of knowledge probes with semi-automatic term extraction since knowledge probes usually occur in the vicinity of terms.