Modeling of Flowing Film Concentrators - Part 1. Water Split Behaviour

A large number of mineral processing equipment employs the basic principles of gravity concentration in a flowing fluid of a few millimetres thick in small open channels where the particles are distributed along the flow height based on their physical properties and the fluid flow characteristics. Fluid flow behaviour and slurry transportation characteristics in open channels have been the research topic for many years in many engineering disciplines. However, the open channels used in the mineral processing industries are different in terms of the size of the channel and the flow velocity used. Understanding of water split behaviour is, therefore, essential in modeling flowing film concentrators. In this paper, an attempt has been made to model the water split behaviour in an inclined open rectangular channel, resembling the actual size and the flow velocity used by the mineral processing industries, based on the Prandtl's mixing length approach. (c) 2006 Elsevier B.V. All rights reserved.

Numerical simulation of magnetite segregation in a dense medium cyclone

Numerical simulations of turbulent driven flow in a dense medium cyclone with magnetite medium have been conducted using Fluent. The predicted air core shape and diameter were found to be close to the experimental results measured by gamma ray tomography. It is possible that the Large eddy simulation (LES) turbulence model with Mixture multi-phase model can be used to predict the air/slurry interface accurately although the LES may need a finer grid. Multi-phase simulations (air/water/medium) are showing appropriate medium segregation effects but are over-predicting the level of segregation compared to that measured by gamma-ray tomography in particular with over prediction of medium concentrations near the wall. Further, investigated the accurate prediction of axial segregation of magnetite using the LES turbulence model together with the multi-phase mixture model and viscosity corrections according to the feed particle loading factor. Addition of lift forces and viscosity correction improved the predictions especially near the wall. Predicted density profiles are very close to gamma ray tomography data showing a clear density drop near the wall. The effect of size distribution of the magnetite has been fully studied. It is interesting to note that the ultra-fine magnetite sizes (i.e. 2 and 7 mu m) are distributed uniformly throughout the cyclone. As the size of magnetite increases, more segregation of magnetite occurs close to the wall. The cut-density (d(50)) of the magnetite segregation is 32 gm, which is expected with superfine magnetite feed size distribution. At higher feed densities the agreement between the [Dungilson, 1999; Wood, J.C., 1990. A performance model for coal-washing dense medium cyclones, Ph.D. Thesis, JKMRC, University of Queensland] correlations and the CFD are reasonably good, but the overflow density is lower than the model predictions. It is believed that the excessive underflow volumetric flow rates are responsible for under prediction of the overflow density. (c) 2006 Elsevier Ltd. All rights reserved.

Study of flow behaviour in a three-product cyclone using computational fluid dynamics

Simplicity in design and minimal floor space requirements render the hydrocyclone the preferred classifier in mineral processing plants. Empirical models have been developed for design and process optimisation but due to the complexity of the flow behaviour in the hydrocyclone these do not provide information on the internal separation mechanisms. To study the interaction of design variables, the flow behaviour needs to be considered, especially when modelling the new three-product cyclone. Computational fluid dynamics (CFD) was used to model the three-product cyclone, in particular the influence of the dual vortex finder arrangement on flow behaviour. From experimental work performed on the UG2 platinum ore, significant differences in the classification performance of the three-product cyclone were noticed with variations in the inner vortex finder length. Because of this simulations were performed for a range of inner vortex finder lengths. Simulations were also conducted on a conventional hydrocyclone of the same size to enable a direct comparison of the flow behaviour between the two cyclone designs. Significantly, high velocities were observed for the three-product cyclone with an inner vortex finder extended deep into the conical section of the cyclone. CFD studies revealed that in the three-product cyclone, a cylindrical shaped air-core is observed similar to conventional hydrocyclones. A constant diameter air-core was observed throughout the inner vortex finder length, while no air-core was present in the annulus. (c) 2006 Elsevier Ltd. All rights reserved.

CFD simulations of hydrocyclones with an air core - Comparison between large eddy simulations and a second moment closure

CFD simulations of the 75 mm, hydrocyclone of Hsieh (1988) have been conducted using Fluent TM. The simulations used 3-dimensional body fitted grids. The simulations were two phase simulations where the air core was resolved using the mixture (Manninen et al., 1996) and VOF (Hirt and Nichols, 1981) models. Velocity predictions from large eddy simulations (LES), using the Smagorinsky-Lilly sub grid scale model (Smagorinsky, 1963; Lilly, 1966) and RANS simulations using the differential Reynolds stress turbulence model (Launder et al., 1975) were compared with Hsieh's experimental velocity data. The LES simulations gave very good agreement with Hsieh's data but required very fine grids to predict the velocities correctly in the bottom of the apex. The DRSM/RANS simulations under predicted tangential velocities, and there was little difference between the velocity predictions using the linear (Launder, 1989) and quadratic (Speziale et al., 1991) pressure strain models. Velocity predictions using the DRSM turbulence model and the linear pressure strain model could be improved by adjusting the pressure strain model constants.

Simulation of a complete reflected shock tunnel showing a vortex mechanism for flow contamination

Simulations of a complete reflected shock tunnel facility have been performed with the aim of providing a better understanding of the flow through these facilities. In particular, the analysis is focused on the premature contamination of the test flow with the driver gas. The axisymmetric simulations model the full geometry of the shock tunnel and incorporate an iris-based model of the primary diaphragm rupture mechanics, an ideal secondary diaphragm and account for turbulence in the shock tube boundary layer with the Baldwin-Lomax eddy viscosity model. Two operating conditions were examined: one resulting in an over-tailored mode of operation and the other resulting in approximately tailored operation. The accuracy of the simulations is assessed through comparison with experimental measurements of static pressure, pitot pressure and stagnation temperature. It is shown that the widely-accepted driver gas contamination mechanism in which driver gas 'jets' along the walls through action of the bifurcated foot of the reflected shock, does not directly transport the driver gas to the nozzle at these conditions. Instead, driver gas laden vortices are generated by the bifurcated reflected shock. These vortices prevent jetting of the driver gas along the walls and convect driver gas away from the shock tube wall and downstream into the nozzle. Additional vorticity generated by the interaction of the reflected shock and the contact surface enhances the process in the over-tailored case. However, the basic mechanism appears to operate in a similar way for both the over-tailored and the approximately tailored conditions.

Using computational fluid dynamics in combating erosion-corrosion

Computational fluid dynamics was used to search for the links between the observed pattern of attack seen in a bauxite refinery's heat exchanger headers and the hydrodynamics inside the header. Validation of the computational fluid dynamics results was done by comparing then with flow parameters measured in a 1:5 scale model of the first pass header in the laboratory. Computational fluid dynamics simulations were used to establish hydrodynamic similarity between the 1:5 scale and full scale models of the first pass header. It was found that the erosion-corrosion damage seen at the tubesheet of the first pass header was a consequence of increased levels of turbulence at the tubesheet caused by a rapidly turning flow. A prismatic flow corrections device introduced in the past helped in rectifying the problem at the tubesheet but exaggerated the erosion-corrosion problem at the first pass header shell. A number of alternative flow correction devices were tested using computational fluid dynamics. Axial ribbing in the first pass header and an inlet flow diffuser have shown the best performance and were recommended for implementation. Computational fluid dynamics simulations have revealed a smooth orderly low turbulence flow pattern in the second, third and fourth pass as well as the exit headers where no erosion-corrosion was seen in practice. This study has confirmed that near-wall turbulence intensity, which can be successfully predicted by using computational fluid dynamics, is a good hydrodynamic predictor of erosion-corrosion damage in complex geometries. (c) 2006 Published by Elsevier Ltd.

An experimental study of the jet of a boat propeller

An experimental study of the velocity and concentration (scalar) fields of a propeller is presented. Field and laboratory measurements were undertaken. The former were up to 50 diameters downstream. Important findings were that the mean velocity and scalar fields quickly become Gaussian while further downstream they both become irregular sometimes approaching approximately linear profiles. Propeller turbulence causes rapid mixing giving an initial concentration dilution factor of 1/20,000 after fifty propeller diameters. Some preliminary comparisons with field measurements of an actual boat in a natural waterway are made. Considerably more work is needed to gain a full understanding of the complex problem of propeller mixing.

Direct numerical simulation of turbulent flow and mass transfer around a rotating circular cylinder

Turbulent flow around a rotating circular cylinder has numerous applications including wall shear stress and mass-transfer measurement related to the corrosion studies. It is also of interest in the context of flow over convex surfaces where standard turbulence models perform poorly. The main purpose of this paper is to elucidate the basic turbulence mechanism around a rotating cylinder at low Reynolds numbers to provide a better understanding of flow fundamentals. Direct numerical simulation (DNS) has been performed in a reference frame rotating at constant angular velocity with the cylinder. The governing equations are discretized by using a finite-volume method. As for fully developed channel, pipe, and boundary layer flows, a laminar sublayer, buffer layer, and logarithmic outer region were observed. The level of mean velocity is lower in the buffer and outer regions but the logarithmic region still has a slope equal to the inverse of the von Karman constant. Instantaneous flow visualization revealed that the turbulence length scale typically decreases as the Reynolds number increases. Wavelet analysis provided some insight into the dependence of structural characteristics on wave number. The budget of the turbulent kinetic energy was computed and found to be similar to that in plane channel flow as well as in pipe and zero pressure gradient boundary layer flows. Coriolis effects show as an equivalent production for the azimuthal and radial velocity fluctuations leading to their ratio being lowered relative to similar nonrotating boundary layer flows.

Simulating spray deposition on plant canopies within a wind tunnel

Three-dimensional computer modelling techniques are being used to develop a probabilistic model of turbulence-related spray transport around various plant architectures to investigate the influence of plant architectures and crop geometry on the sprayapplication process. Plant architecture models that utilise a set of growth rules expressed in the Lindenmayer systems (L-systems) formalism have been developed and programmed using L-studio software. Modules have been added to simulate the movement ofdroplets through the air and deposition on the plant canopy. Deposition of spray on an artificial plant structure was measured in the wind tunnel at the University of Queensland, Gatton campus and the results compared to the model simulation. Further trials are planned to measure the deposition of spray droplets on various crop and weed species and the results from these trials will be used to refine and validate the combined spray and plant architecture model.

Experiments to assess the transport of fibrous insulation debris

Loss of coolant accidents (LOCA) in the primary cooling circuit of a nuclear reactor may result in damage to insulation materials that are located near to the leak. The insulation materials released may compromise the operation of the emergency core cooling system (ECCS). Insulation material in the form of mineral wool fibre agglomerates (MWFA) maybe transported to the containment sump strainers mounted at the inlet of the emergency cooling pumps, where the insulation fibres may block or penetrate the strainers. In addition to the impact of MWFA on the pressure drop across the strainers, corrosion products formed over time may also accumulate in the fibre cakes on the strainers, which can lead to a significant increase in the strainer pressure drop and result in cavitation in the ECCS. Thus, knowledge of transport characteristics of the damaged insulation materials in various scenarios is required to help plan for the long-term operability of nuclear reactors, which undergo LOCA. An experimental and theoretical study performed by the Helmholtz-Zentrum Dresden-Rossendorf and the Hochschule Zittau/Görlitz1 is investigating the phenomena that maybe observed in the containment vessel during a LOCA. The study entails the generation of fibre agglomerates, the determination of their transport properties in single and multi-effect experiments and the long-term effect that corrosion of the containment internals by the coolant has on the strainer pressure drop. The focus of this presentation is on the experiments performed that characterize the horizontal transport of MWFA, whereas the corresponding CFD simulations are described in an accompanying contribution (see abstract of Cartland Glover et al.). The experiments were performed a racetrack type channel that provided a near uniform horizontal flow. The channel is 0.1 wide by 1.2 m high with a straight length of 5 m and two bends of 0.5 m. The measurement techniques include particle imaging (both wide-angle and macro lens), concurrent particle image velocimetry, ultravelocimetry, laser detection sensors to sense the presence of absence of MWFA and pertinent measurements of the MWFA concentration and quiescent settling characteristics. The transport of the MWFA was observed at velocities of 0.1 and 0.25 m s-1 to verify numerical model behaviour in and just beyond expected velocities in the containment sump of a nuclear reactor.

Purification of phosphoric acid by solvent extraction

This work follows a feasibility study (187) which suggested that a process for purifying wet-process phosphoric acid by solvent extraction should be economically viable. The work was divided into two main areas, (i) chemical and physical measurements on the three-phase system, with or without impurities; (ii) process simulation and optimization. The object was to test the process technically and economically and to optimise the type of solvent. The chemical equilibria and distribution curves for the system water - phosphoric acid - solvent for the solvents n-amyl alcohol, tri-n-butyl phosphate, di-isopropyl ether and methyl isobutyl ketone have been determined. Both pure phosphoric acid and acid containing known amounts of naturally occurring impurities (Fe P0 4 , A1P0 4 , Ca3(P04)Z and Mg 3(P0 4 )Z) were examined. The hydrodynamic characteristics of the systems were also studied. The experimental results obtained for drop size distribution were compared with those obtainable from Hinze's equation (32) and it was found that they deviated by an amount related to the turbulence. A comprehensive literature survey on the purification of wet-process phosphoric acid by organic solvents has been made. The literature regarding solvent extraction fundamentals and equipment and optimization methods for the envisaged process was also reviewed. A modified form of the Kremser-Brown and Souders equation to calculate the number of contact stages was derived. The modification takes into account the special nature of phosphoric acid distribution curves in the studied systems. The process flow-sheet was developed and simulated. Powell's direct search optimization method was selected in conjunction with the linear search algorithm of Davies, Swann and Campey. The objective function was defined as the total annual manufacturing cost and the program was employed to find the optimum operating conditions for anyone of the chosen solvents. The final results demonstrated the following order of feasibility to purify wet-process acid: di-isopropyl ether, methylisobutyl ketone, n-amyl alcohol and tri-n-butyl phosphate.

The future of manufacturing

Anyone who looks at the title of this special issue will agree that the intent behind the preparation of this volume was ambitious: to predict and discuss “The Future of Manufacturing”. Will manufacturing be important in the future? Even though some sceptics might say not, and put on the table some old familiar arguments, we would strongly disagree. To bring subsidies for the argument we issued the call-for-papers for this special issue of Journal of Manufacturing Technology Management, fully aware of the size of the challenge in our hands. But we strongly believed that the enterprise would be worthwhile. The point of departure is the ongoing debate concerning the meaning and content of manufacturing. The easily visualised internal activity of using tangible resources to make physical products in factories is no longer a viable way to characterise manufacturing. It is now a more loosely defined concept concerning the organisation and management of open, interdependent, systems for delivering goods and services, tangible and intangible, to diverse types of markets. Interestingly, Wickham Skinner is the most cited author in this special issue of JMTM. He provides the departure point of several articles because his vision and insights have guided and inspired researchers in production and operations management from the late 1960s until today. However, the picture that we draw after looking at the contributions in this special issue is intrinsically distinct, much more dynamic, and complex. Seven articles address the following research themes: 1.new patterns of organisation, where the boundaries of firms become blurred and the role of the firm in the production system as well as that of manufacturing within the firm become contingent; 2.new approaches to strategic decision-making in markets characterised by turbulence and weak signals at the customer interface; 3.new challenges in strategic and operational decisions due to changes in the profile of the workforce; 4.new global players, especially China, modifying the manufacturing landscape; and 5.new techniques, methods and tools that are being made feasible through progress in new technological domains. Of course, many other important dimensions could be studied, but these themes are representative of current changes and future challenges. Three articles look at the first theme: organisational evolution of production and operations in firms and networks. Karlsson's and Skold's article represent one further step in their efforts to characterise “the extraprise”. In the article, they advance the construction of a new framework, based on “the network perspective” by defining the formal elements which compose it and exploring the meaning of different types of relationships. The way in which “actors, resources and activities” are conceptualised extends the existing boundaries of analytical thinking in operations management and open new avenues for research, teaching and practice. The higher level of abstraction, an intrinsic feature of the framework, is associated to the increasing degree of complexity that characterises decisions related to strategy and implementation in the manufacturing and operations area, a feature that is expected to become more and more pervasive as time proceeds. Riis, Johansen, Englyst and Sorensen have also based their article on their previous work, which in this case is on “the interactive firm”. They advance new propositions on strategic roles of manufacturing and discuss why the configuration of strategic manufacturing roles, at the level of the network, will become a key issue and how the indirect strategic roles of manufacturing will become increasingly important. Additionally, by considering that value chains will become value webs, they predict that shifts in strategic manufacturing roles will look like a sequence of moves similar to a game of chess. Then, lastly under the first theme, Fleury and Fleury develop a conceptual framework for the study of production systems in general derived from field research in the telecommunications industry, here considered a prototype of the coming information society and knowledge economy. They propose a new typology of firms which, on certain dimensions, complements the propositions found in the other two articles. Their telecoms-based framework (TbF) comprises six types of companies characterised by distinct profiles of organisational competences, which interact according to specific patterns of relationships, thus creating distinct configurations of production networks. The second theme is addressed by Kyläheiko and SandstroÍm in their article “Strategic options based framework for management of dynamic capabilities in manufacturing firms”. They propose a new approach to strategic decision-making in markets characterised by turbulence and weak signals at the customer interface. Their framework for a manufacturing firm in the digital age leads to active asset selection (strategic investments in both tangible and intangible assets) and efficient orchestrating of the global value net in “thin” intangible asset markets. The framework consists of five steps based on Porter's five-forces model, the resources-based view, complemented by means of the concepts of strategic options and related flexibility issues. Thun, GroÍssler and Miczka's contribution to the third theme brings the human dimension to the debate regarding the future of manufacturing. Their article focuses on the challenges brought to management by the ageing of workers in Germany but, in the arguments that are raised, the future challenges associated to workers and work organisation in every production system become visible and relevant. An interesting point in the approach adopted by the authors is that not only the factual problems and solutions are taken into account but the perception of the managers is brought into the picture. China cannot be absent in the discussion of the future of manufacturing. Therefore, within the fourth theme, Vaidya, Bennett and Liu provide the evidence of the gradual improvement of Chinese companies in the medium and high-tech sectors, by using the revealed comparative advantage (RCA) analysis. The Chinese evolution is shown to be based on capabilities developed through combining international technology transfer and indigenous learning. The main implication for the Western companies is the need to take account of the accelerated rhythm of capability development in China. For other developing countries China's case provides lessons of great importance. Finally, under the fifth theme, Kuehnle's article: “Post mass production paradigm (PMPP) trajectories” provides a futuristic scenario of what is already around us and might become prevalent in the future. It takes a very intensive look at a whole set of dimensions that are affecting manufacturing now, and will influence manufacturing in the future, ranging from the application of ICT to the need for social transparency. In summary, this special issue of JMTM presents a brief, but undisputable, demonstration of the possible richness of manufacturing in the future. Indeed, we could even say that manufacturing has no future if we only stick to the past perspectives. Embracing the new is not easy. The new configurations of production systems, the distributed and complementary roles to be performed by distinct types of companies in diversified networked structures, leveraged by the new emergent technologies and associated the new challenges for managing people, are all themes that are carriers of the future. The Guest Editors of this special issue on the future of manufacturing are strongly convinced that their undertaking has been worthwhile.

The changing roles of production and operations managers in Britain from the 1970s to the 1990s

This article examines the careers and changing roles of British production and operations managers through three surveys covering the last quarter of the twentieth century. Careers are examined in terms of both their organisational context and the subjective experiences of those who have chosen this field, during a period of great turbulence for manufacturing due to growing global competition. The persistent features of such roles and responsibilities are contrasted with the changes in focus and demands. The managers' sources of satisfaction and frustration are outlined as are their perceptions of their situation in relation to managers in other areas. The article concludes by considering what has changed and what needs to change, in order for manufacturing to gain maximum benefit from the contribution of these managers.

Strategic planning and performance:extending the debate

This article extends the debate regarding the relationship between strategic planning and performance. It addresses criticism of previous empirical studies that have largely investigated direct and bi-variate relationships, producing equivocal results. The current study investigates the mediating effects of four types of flexibility on the strategic planning and performance relationship. Flexibility is defined as the extent to which new and alternative decisions are generated and considered in strategic planning, allowing for positive organizational change and adaptation to environmental turbulence. Through investigating simultaneous equations in a structural equation model, we find that two types of flexibility mediate the relationship between strategic planning and financial performance, while the other two types mediate the relationship between strategic planning and non-financial performance. The results are new empirical insights that have not been previously reported.