Sorption kinetics and intrapaticulate diffusivity of As(III) bioremediation from aqueous solution, using modified and unmodified coconut fiber

The pollution and toxicity problems posed by arsenic in the environment have long been established. Hence, the removal and recovery remedies have been sought, bearing in mind the efficiency, cost effectiveness and environmental friendliness of the methods employed. The sorption kinetics and intraparticulate diffusivity of As (III) bioremediation from aqueous solution using modified and unmodified coconut fiber was investigated. The amount adsorbed increased as time increased, reaching equilibrium at about 60 minutes. The kinetic studies showed that the sorption rates could be described by both pseudo-first order and pseudo-second order process with the later showing a better fit with a value of rate constant of 1.16 x 10-4 min-1 for the three adsorbent types. The mechanism of sorption was found to be particle diffusion controlled. The diffusion and boundary layer effects were also investigation. Therefore, the results show that coconut fiber, both modified and unmodified is an efficient sorbent for the removal of As (III) from industrial effluents with particle diffusion as the predominant mechanism.

Immersion enthalpy variation of surface-modified mineral activated carbon in lead (II) aqueous solution adsorption: the relation between immersion enthalpy and adsorption capacity

An activated carbon was obtained by chemical activation with phosphoric acid, CM, from a mineral carbon. Afterwards, the carbon was modified with 2 and 5 molL-1, CMox2 and CMox5 nitric acid solutions to increase the surface acid group contents. Immersion enthalpy at pH 4 values and Pb2+ adsorption isotherms were determined by immersing activated carbons in aqueous solution. The surface area values of the adsorbents and total pore volume were approximately 560 m².g-1 and 0.36 cm³g-1, respectively. As regards chemical characteristics, activated carbons had higher acid sites content, 0.92-2.42 meq g-1, than basic sites, 0.63-0.12 meq g-1. pH values were between 7.4 and 4.5 at the point of zero charge, pH PZC. The adsorbed quantity of Pb2+ and the immersion enthalpy in solution of different pH values for CM activated carbon showed that the values are the highest for pH 4, 15.7 mgg-1 and 27.6 Jg-1 respectively. Pb2+ adsorption isotherms and immersion enthalpy were determined for modified activated carbons and the highest values were obtained for the activated carbon that showed the highest content of total acid sites on the surface.

A fluorescence probe study of gemini surfactants in aqueous solution: a comparison between n-2-n and n-6-n series of the alkanediyl-a,w-bis (dimethylalkylammonium bromides)

Two series of alkanediyl-a,w-bis (dimethylalkylammonium bromide (n-2-n and n-6-n; n=8, 10,12, and 16) have been synthesized and their micelles properties studied in aqueous solution using pyrene, pyrenecarboxaldehyde (PCA) and 1,8 anilinonaphtalene sulfonic acid sodium salt (ANS) as fluorescent probes. The micelles from these surfactants have been characterized on the basis of the information provided by micelle-solubilized fluorescent probes. The obtained results indicated that the surfactant concentration at which a marked decrease in l max parameter of pyrenecarboxaldehyde (PCA) occurs corresponds to the CMC determined by conductimetric measurements. Changes in the emission spectra of ANS and PCA observed in the submicellar range for both surfactants series (n-2-n and n-6-n) were interpreted as formation of pre-aggregates. It was found that the dimeric surfactants with long spacer (s= 6) form more hydrated aggregates when compared with those formed by the n-2-n and CnTAB surfactants series. This was attributed to a more difficult packing of n-6-n surfactant molecules to form micelles.

The concept of solution: Industry’s insights compared to theoretical views

Many manufacturing companies have started to offer complete solutions to their customers’ unique needs due to toughening competition and customer demand. Discourse on this kind of solution business is still developing, hence, there is not an established definition for the concept of solution. The aim of the study is to profoundly identify the concept of solution and to understand how the industry’s current views differ from the theoretical concepts. The describing dimensions are identified from selected 13 theoretical notions, and from responses, that the employees of five different companies have given. The 32 interview transcripts are analyzed with thematic analysis and qualitative content analysis. According to the findings, the concept of solution is characterized by integration, customization, risk-sharing, value co-creation, long-term orientation, and desired outcomes. The industry’s insights differ in terms of them all. The results illustrate, that a solution is a bundle, and the whole solution is customized on some level for a client. A solution supplier needs to be customer-focused, in which value co-creation is only a part. The solution solves the customer’s problem, and improves both the customer’s, and the supplier’s business. Neither long-term focus nor risks-sharing were directly employed to characterize the concept of solution. Differences are mainly due to the different approaches to the definitions and inexperience of the companies.

Evaluating the Advantages of Implementing a CRM solution

CRM-järjestelmän avulla pyritään yleisesti tehostamaan liiketoimintaprosesseja. Yrityksestä, kuin myös toimialasta riippuen hyödyt sekä tavoitteet vaihtelevat jonkin verran. Usein CRM-järjestelmän avulla saavutettavien hyötyjen mittaaminen ja arviointi organisaatiossa koetaan hankalaksi ja täten todellinen hyötyjen arviointi jää suppeaksi. Tämän tutkimuksen tavoitteena oli kartoittaa etuja, joita CRM-järjestelmän käyttöönotto on todellisuudessa tuonut yrityksille. Tutkimus kulminoituu laskentamalliin, jonka avulla CRM käytön hyödyt konvertoidaan konkreettiseksi rahasummaksi. Tutkimuksessa pyritään vastaamaan seuraaviin tutkimuskysymyksiin: 1. Kun yritys suunnitteli CRM-sovelluksen käyttöönottoa, mitkä olivat järjestelmälle asetetut tavoitteet? 2. Onko yritys saavuttanut CRM-järjestelmälle asetetut tavoitteet? 3. Onko yritys saavuttanut odottamattomia hyötyjä CRM-järjestelmän käytön avulla? 4. Mitkä ovat CRM-järjestelmän tärkeimmät kehityskohteet käyttökokemusten perusteella? Tutkimus perustuu CRM-kirjallisuuden avulla luotuun teoriaviitekehykseen. Teoriaviitekehyksen pohjalta luotiin ideaalimalli ja mallin pohjalta web-survey -kysely. Kyselyn tulosten perusteella toteutettiin haastatteluja, joilla pyrittiin saamaan tutkimustuloksiin syvyyttä.

Non-Markovianity and Quantum Correlations in Qubit-Systems

In this Thesis I discuss the exact dynamics of simple non-Markovian systems. I focus on fundamental questions at the core of non-Markovian theory and investigate the dynamics of quantum correlations under non-Markovian decoherence. In the first context I present the connection between two different non-Markovian approaches, and compare two distinct definitions of non-Markovianity. The general aim is to characterize in exemplary cases which part of the environment is responsible for the feedback of information typical of non- Markovian dynamics. I also show how such a feedback of information is not always described by certain types of master equations commonly used to tackle non-Markovian dynamics. In the second context I characterize the dynamics of two qubits in a common non-Markovian reservoir, and introduce a new dynamical effect in a wellknown model, i.e., two qubits under depolarizing channels. In the first model the exact solution of the dynamics is found, and the entanglement behavior is extensively studied. The non-Markovianity of the reservoir and reservoirmediated-interaction between the qubits cause non-trivial dynamical features. The dynamical interplay between different types of correlations is also investigated. In the second model the study of quantum and classical correlations demonstrates the existence of a new effect: the sudden transition between classical and quantum decoherence. This phenomenon involves the complete preservation of the initial quantum correlations for long intervals of time of the order of the relaxation time of the system.

A quasi-materialist, quasi-dualist solution to the mind-body problem

If the mental can affect, or be affected by, the physical, then the mental must itself be physical. Otherwise the physical world would not be explanatorily closed. But it is closed. There are reasons to hold that materialism (in both its reductive and non-reductive varieties) is false. So how are we to explain the apparent responsiveness of the physical to the mental and vice versa? The only possible solution seems to be this: physical objects are really projections or isomorphs of objects whose essential properties are mental. (A slightly less accurate way of putting this would be to say: the constitutive - i.e. the non-structural and non-phenomenal - properties of physical objects are mental, i.e. are such as we are used to encountering only in "introspection".) The chair, qua thing that I can know through sense perception, and through hypotheses based strictly thereupon, is a kind of shadow of an object that is exactly like it, except that this other objects essential properties are mental. This line of thought, though radically counterintuitive, explains the apparent responsiveness of the mental to the physical, and vice versa, without being open to any of the criticisms to which materialism, dualistic interaction ism, and epiphenomenalism are open.

Etiology and epidemiology of Pythium root rot in hydroponic crops: current knowledge and perspectives

The etiology and epidemiology of Pythium root rot in hydroponically-grown crops are reviewed with emphasis on knowledge and concepts considered important for managing the disease in commercial greenhouses. Pythium root rot continually threatens the productivity of numerous kinds of crops in hydroponic systems around the world including cucumber, tomato, sweet pepper, spinach, lettuce, nasturtium, arugula, rose, and chrysanthemum. Principal causal agents include Pythium aphanidermatum, Pythium dissotocum, members of Pythium group F, and Pythium ultimum var. ultimum. Perspectives are given of sources of initial inoculum of Pythium spp. in hydroponic systems, of infection and colonization of roots by the pathogens, symptom development and inoculum production in host roots, and inoculum dispersal in nutrient solutions. Recent findings that a specific elicitor produced by P. aphanidermatum may trigger necrosis (browning) of the roots and the transition from biotrophic to necrotrophic infection are considered. Effects on root rot epidemics of host factors (disease susceptibility, phenological growth stage, root exudates and phenolic substances), the root environment (rooting media, concentrations of dissolved oxygen and phenolic substances in the nutrient solution, microbial communities and temperature) and human interferences (cropping practices and control measures) are reviewed. Recent findings on predisposition of roots to Pythium attack by environmental stress factors are highlighted. The commonly minor impact on epidemics of measures to disinfest nutrient solution as it recirculates outside the crop is contrasted with the impact of treatments that suppress Pythium in the roots and root zone of the crop. New discoveries that infection of roots by P. aphanidermatum markedly slows the increase in leaf area and whole-plant carbon gain without significant effect on the efficiency of photosynthesis per unit area of leaf are noted. The platform of knowledge and understanding of the etiology and epidemiology of root rot, and its effects on the physiology of the whole plant, are discussed in relation to new research directions and development of better practices to manage the disease in hydroponic crops. Focus is on methods and technologies for tracking Pythium and root rot, and on developing, integrating, and optimizing treatments to suppress the pathogen in the root zone and progress of root rot.

General terms and rigidity: another solution to the trivialization problem

In this paper I am concerned with the problem of applying the notion of rigidity to general terms. In Naming and Necessity, Kripke has clearly suggested that we should include some general terms among the rigid ones, namely, those common nouns semantically correlated with natural substances, species and phenomena, in general, natural kinds -'water', 'tiger', 'heat'- and some adjectives -'red', 'hot', 'loud'. However, the notion of rigidity has been defined for singular terms; after all, the notion that Kripke has provided us with is the notion of a rigid designator. But general terms do not designate single individuals: rather, they apply to many of them. In sum, the original concept of rigidity cannot be straightforwardly applied to general terms: it has to be somehow redefined in order to make it cover them. As is known, two main positions have been put forward to accomplish that task: the identity of designation conception, according to which a rigid general term is one that designates the same property or kind in all possible worlds, and the essentialist conception, which conceives of a rigid general term as an essentialist one, namely, a term that expresses an essential property of an object. My purpose in the present paper is to defend a particular version of the identity of designation conception: on the proposed approach, a rigid general term will be one that expresses the same property in all possible worlds and names the property it expresses. In my opinion, the position can be established on the basis of an inference to the best explanation of our intuitive interpretation and evaluation, relative to counterfactual circumstances, of statements containing different kinds of general terms, which is strictly analogous to our intuitive interpretation and evaluation, relative to such circumstances, of statements containing different kinds of singular ones. I will argue that it is possible to offer a new solution to the trivialization problem that is thought to threaten all versions of the identity of designation conception of rigidity. Finally, I will also sketch a solution to the so-called 'over-generalization and under-generalization problems', both closely related to the above-mentioned one.

Effects of different light levels on the initial growth and photosynthesis of Croton urucurana Baill. in southeastern Brazil

Four levels of shading (full sunlight (0%), 30, 50, 70% of solar radiation interception on growth, chlorophyll concentration and photosynthetic rate were studied in Croton urucurana Baill., a pioneer plant species. This species seedlings are of potential interest for reforestation projects and recovery of degraded areas. The seedlings were grown in pots containing soil and sand (2:1) and later transferred to plastic bags of 3 dm³ and submitted to different levels of shading (30, 50, 70%) of solar radiation and full sunlight, as control. The experimental design was completely randomized with five replicates and each experimental unit was composed of five plants. The results suggest that plants submitted to 70% shading showed higher dry weight accumulation in leaf and root, and higher plant height and leaf area. However, the seedlings root system showed higher dry biomass under full sunlight. It was observed a tendency to increase chlorophyll concentration and to decrease photosynthetic rate with the increase of the shading level.

EDTA- and DTPA-functionalized silica gel and chitosan adsorbents for the removal of heavy metals from aqueous solutions

Adsorbents functionalized with chelating agents are effective in removal of heavy metals from aqueous solutions. Important properties of such adsorbents are high binding affinity as well as regenerability. In this study, aminopolycarboxylic acid, EDTA and DTPA, were immobilized on the surface of silica gel, chitosan, and their hybrid materials to achieve chelating adsorbents for heavy metals such as Co(II), Ni(II), Cd(II), and Pb(II). New knowledge about the adsorption properties of EDTA- and DTPA-functionalizedadsorbents was obtained. Experimental work showed the effectiveness, regenerability, and stability of the studied adsorbents. Both advantages and disadvantages of the adsorbents were evaluated. For example, the EDTA-functionalized chitosan-silica hybrid materials combined the benefits of the silica gel and chitosan while at the same time diminishing their observed drawbacks. Modeling of adsorption kinetics and isotherms is an important step in design process. Therefore, several kinetic and isotherm models were introduced and applied in this work. Important aspects such as effect of error function, data range, initial guess values, and linearization were discussed and investigated. The selection of the most suitable model was conducted by comparing the experimental and simulated data as well as evaluating the correspondence between the theory behind the model and properties of the adsorbent. In addition, modeling of two-component data was conducted using various extended isotherms. Modeling results for both one- and twocomponent systems supported each other. Finally, application testing of EDTA- and DTPA-functionalized adsorbents was conducted. The most important result was the applicability of DTPA-functionalized silica gel and chitosan in the capturing of Co(II) from its aqueous EDTA-chelate. Moreover, these adsorbents were efficient in various solution matrices. In addition, separation of Ni(II) from Co(II) and Ni(II) and Pb(II) from Co(II) and Cd(II) was observed in two- and multimetal systems. Lastly, prior to their analysis, EDTA- and DTPA-functionalized silica gels were successfully used to preconcentrate metal ions from both pure and salty waters

Imazapyr root exudation from eucalypt seedlings cultivated in nutritive solution

Imazapyr has been used in Brazilian eucalypt cultivation for the maintenance of clearings and coppicing control in areas undergoing stand reform. However, inquiries have been made as to the final fate of the molecule. Imazapyr root exudation in eucalypt plants was evaluated through a bioassay under greenhouse conditions, by applying different herbicide doses (0.000, 0.375, 0.750, 1.125, and 1.500 kg ha-1 a.i.) on Eucalyptus grandis seedlings derived from vegetative propagation, hydroponically cultivated in 2.500 ml vases. Forty-day-old seedlings of the same clone were used as bioindicators, transplanted to the vases two days after herbicide application. After a period of 13 days of coexistence, the sprayed plants were removed and discarded; ten days later, the visual symptoms of toxicity were evaluated and the total dry biomass (aerial part and roots) of the bioindicators were determined. The lowest herbicide dose (0.375 kg ha-1 a.i.) affected the total biomass and growth, being most evident in the aerial part, with larger I50 for root dry biomass. The E. grandis seedlings exuded imazapyr, and/or its metabolites, in concentrations capable of affecting the growth of plants of the same species.

Initial development and gas exchange of Talisia subalbens (Mart.) Radlk. under different shading conditions

Ecophysiological studies under semi-controlled conditions in nurseries and greenhouses are essential to enable the use of native species to recover degraded areas and for commercial planting. Talisia subalbens (Mart) Radlk, 'cascudo', is a native fruiting species of the Cerrado on the verge of extinction. The ecophysiological performance of this species was evaluated in nursery conditions under different levels of shading (full sunshine, 30%, 50% and 70%). Initial growth, biomass allocation, gas exchange and chlorophyll content of the plants were analyzed. Full sunshine cultivated plants showed a higher accumulation of total, shoot, and root dry biomass. There was no significant difference in the root/shoot ratio among the treatments. Seedlings cultivated under full sunshine and 30% shading showed higher values for height, basal diameter, and leaf area. Differences in stomata conductance and photosynthesis rate were not observed among the different shading levels. Plants cultivated under 70% of shading had higher contents of chlorophyll a, b, and total. During the initial phase with higher levels of radiation were fundamental for the development of T. subalbens seedlings.

Planting density and initial growth of two tree species adapted to the semi-arid region

Planting densities influence several aspects of forest formation, including management practices, timber yield, quality, and extraction, and consequently its production costs. The objective of this study was to evaluate Mimosa caesalpiinifolia and Gliricidia sepium growth as a function of planting density (400, 600, 800, 1000, and 1200 plants ha-1) and plant age. The species were evaluated every 90 days for plant height (PH), crown diameter (CD) and root collar diameter (RCD) (10 cm above the ground), with the first evaluation performed at 90 days and the last at 720 days. When plants were one year of age and beyond, evaluations were conducted also for stem diameter at breast height (DBH) (1.30 m above the ground). A randomized block design with split-plots and three replicates was adopted. Species were assigned to plots, planting densities were assigned to subplots, and evaluation ages were assigned to subsubplots. The four traits in both species had their values decreased as planting density increased, but continually increased as plant age increased. For PH and RCD there was an alternation between species superiority, with gliricidia being superior to sabiá at some ages, while the opposite occurred at other ages. As to CD the species only differed in the last measurement, gliricidia being superior. With regard to DBH, gliricidia was superior starting from the second measurement. There was an effect of the species × ages interaction for the four traits and also an effect of the densities × ages interaction for CD and DBH.

Konventionaalisen jätehuollon kehittäminen Loviisan voimalaitoksella

Tämän diplomityön tarkoituksena oli löytää kehityskohteita Fortumin Loviisan ydinvoimalaitoksen konventionaalisesta, eli tavanomaisesta, jätehuollosta. Tavoitteena oli löytää erityisesti keinoja kaatopaikkajätteen määrän vähentämiseksi sekä lajittelun tehostamiseksi. Myös jätelainsäädännön kokonaisuudistuksen vaikutukset jätehuollon toimintaan olivat työn kannalta keskeisessä roolissa. Työ tehtiin jätehuoltosuunnitelman rakennetta noudattaen. Jätehuoltosuunnitelma koostuu alkukartoituksesta sekä jätehuoltosuunnitelman laatimisesta ja toteutuksesta. Varsinaisina kehitystarpeiden kartoittamismenetelminä käytettiin viranomaisvaatimusten selvittämistä, toiminnan tarkastelua, jätehuoltokyselyä voimalaitoksen työntekijöille, benchmarkingia sekä valittujen hyötykäyttö- ja loppusijoitusmenetelmien kustannusvertailua. Tulokseksi saatiin, että jätteiden lajittelua voitaisiin tehostaa ennen kaikkea lisäämällä työntekijöiden koulutusta. Lajittelun helpottamiseksi ohjeistuksen tulee olla paremmin saatavilla sekä voimalaitoksen omalle henkilöstölle kuin urakoitsijoillekin. Ongelmajätehuollossa eniten ongelmia ilmeni ongelmajätepakkausten merkitsemisessä jätteiden syntypaikoilla. Tähän ratkaisuna ehdotettiin kokeiltavaksi jätteiden syntykohteisiin sijoitettavia jätekortteja, joista pakkaajat voisivat helposti tarkistaa tarvittavat merkinnät. Myös mustan jäteöljyn keräämistä olisi mahdollista parantaa, jotta suurempi osa siitä saataisiin hyödynnettyä materiaalina. Kaatopaikkajätteen määrän vähentämiseksi työssä ehdotettiin sekajätteen viemistä kaatopaikan sijaan poltettavaksi. Muutoksen seurauksena voimalaitoksen jätehuollon kustannukset saattavat lisääntyä, mutta ympäristön kannalta muutos tulisi olemaan positiivinen.