Improved membranes for the extraction of heavy metals

This work presents a series of experimental tests on new practical approaches in membrane design to improve extraction capacity and rate. We chose an extraction system involving Aliquat 336 as the extractant and Cd(II) as the metal ion to be extracted to demonstrate these new approaches. The core element in the new membrane assembly was the extractant loaded sintered glass filter. This membrane assembly provided a large interface area between the extractant and the aqueous solution containing metal ions. By recycling the aqueous solution through the membrane assembly, the extraction rate was significantly improved. The membrane assembly also offered good extraction capacity.

Observations on the effects of caged carp culture on water and sediment metal concentrations in Lake Kasumingaura, Japan

The concentrations of 24 elements in the sediment and associated water column were monitored at two sites, one an area of intensive cage culture of carp, the other a wild site far from known cage culture areas, in Lake Kasumigaura, Japan, between September 1994 and September 1995. The concentrations of most elements in Lake Kasumigaura are mostly sub-parts per billion, except those for Ca, Fe, K, Mg, Na, P, and Si. The concentrations of Cd, Co, Cu, Mn, Ni, Pb, V, and Fe in Lake Kasumigaura are higher than the values in Lake Mashu, Lake Shikotsu, and Lake Biwa, and comparable to the levels in open ocean. Statistically significant differences in metal concentrations were observed between the culture and wild sites, with metal concentrations consistently higher at the culture site. Although cage culture of carp in the Lake Kasumigaura system may be causing localized increase in metal concentrations in the sediments, we must treat the results with caution, since the concentrations of metals observed in the sediments in 1995 were lower than those observed in 1979 for all metals at both sampling sites. In conclusion, further study of the concentrations of metals in the lake as a whole must be undertaken before the differences between the culture and wild sites can be proved, or disproved, to be the result of carp culture.

Trace metal concentrations in edible tissue of snapper, flathead, lobster, and abalone from coastal waters of Victoria, Australia

The concentrations of heavy metals in the edible tissue of commonly fished species of the Victorian coast of Australia are reported. The metals studied were As, Cd, Cu, Hg, Pb, Se, and Zn and the fish species examined were snapper (Pagruss auratus), flathead (Platycephalus bassenssis and Neoplatycephalus richardsoni), lobster (Jasus edwardsii), and abalone (Haliotis rubra). None of the fish species studied had average concentrations exceeding the maximum levels specified for As, Cd, Hg, and Pb by the Food Standards Australia and New Zealand Food Standards code. Additionally, the concentrations of Cu, Se, and Zn were close to or below the median values generally expected in these species. Essential trace elements Se and Zn were found to be well regulated by all fish species. Although also essential, Cu was not so well regulated, especially in abalone. Nonessential metals As, Cd, and Hg are not regulated in the studied fish and their concentrations in the fish tissue are dependent on size and fishing zone. Metal concentrations were not largely affected by sex. Surprisingly, the concentrations of metals in fish in Port Phillip Bay, a zone, which includes the major cities of Melbourne and Geelong and is known to have high concentrations of metals in the water and sediment, were not consistently higher than those in other less-populated fishing zones.

Amine enrichment of thin-film composite membranes via low pressure plasma polymerization for antimicrobial adhesion

Thin-film composite membranes, primarily based on poly(amide) (PA) semipermeable materials, are nowadays the dominant technology used in pressure driven water desalination systems. Despite offering superior water permeation and salt selectivity, their surface properties, such as their charge and roughness, cannot be extensively tuned due to the intrinsic fabrication process of the membranes by interfacial polymerization. The alteration of these properties would lead to a better control of the materials surface zeta potential, which is critical to finely tune selectivity and enhance the membrane materials stability when exposed to complex industrial waste streams. Low pressure plasma was employed to introduce amine functionalities onto the PA surface of commercially available thin-film composite (TFC) membranes. Morphological changes after plasma polymerization were analyzed by SEM and AFM, and average surface roughness decreased by 29%. Amine enrichment provided isoelectric point changes from pH 3.7 to 5.2 for 5 to 15 min of plasma polymerization time. Synchrotron FTIR mappings of the amine-modified surface indicated the addition of a discrete 60 nm film to the PA layer. Furthermore, metal affinity was confirmed by the enhanced binding of silver to the modified surface, supported by an increased antimicrobial functionality with demonstrable elimination of E. coli growth. Essential salt rejection was shown minimally compromised for faster polymerization processes. Plasma polymerization is therefore a viable route to producing functional amine enriched thin-film composite PA membrane surfaces.

Transition metal rates in latosol twice treated with sewage sludge

A reciclagem agrícola do lodo de esgoto tem provocado o acúmulo de metais pesados no solo e na água, podendo atingir níveis tóxicos e causar danos às plantas cultivadas, aos animais e ao homem, por meio da cadeia trófica. Neste intuito foi desenvolvido o presente experimento, em condições de campo, entre 2000 e 2002, onde foram avaliados os efeitos da aplicação de lodo de esgoto por dois anos, sobre a extração de metais de transição (essenciais e não) pelo extrator DTPA em um Latossolo Vermelho distrófico (LVd) de textura média. As concentrações dos elementos metálicos: Mn, Fe, Cd, Ni, Co, Pb e Cr não foram detectados pelo método da absorção atômica na solução obtida com o extrator DTPA. A aplicação de lodo de esgoto causou inicialmente pequena elevação no pH do solo, posteriormente a diminuição do mesmo, e manteve-se próximo ao original. Foi possível concluir que, com a aplicação consecutiva do lodo, os teores extraíveis de Fe e Mn nas amostras de solos aumentaram gradativamente nos dois anos agrícolas, com as doses do lodo de esgoto aplicado, época de amostragens, e foram superiores ao tratamento testemunha. O extrator apresentou capacidade restrita para avaliação da fitodisponibilidade dos metais pesados decorrentes das baixas concentrações nas amostras de solo.

Banana Peel Applied to the Solid Phase Extraction of Copper and Lead from River Water: Preconcentration of Metal Ions with a Fruit Waste

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sediment grain size distribution and heavy metals determination in a dam on the Parana River at Ilha Solteira, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Variação espacial e sazonal de elementos maiores e traços no estuários do Rio Curimataú (RN), através de dados geoquímicos e de sensoriamento remoto

The Curimataú estuary is located in the oriental coast of Rio Grande do Norte State in Brazil. Its importance resides in the fact that this region possesses one of the last portions of preserved mangrove in the Rio Grande do Norte State. Nevertheless, it has been severely affected by many anthropogenic activities, as sugarcane monoculture and shrimp farming. Former works demonstrated that an accumulation of heavy metals is occurring in oysters in this estuary, and perhaps it could be explained by the input of metals in this ecosystem deriving from the shrimp farming. To better understanding the origin of these metals, bottom sediment samples, cores and suspended particulate matter were collected for a characterization of metal concentrations (Al, Ba, Cd, Cu, Cr, Fe, Mn, Ni, Pb, Zn) and to determine the potentially bioavailable metals. Additionally, the enrichment ratio for each element analyzed was calculated. The mineralogical composition of sediment samples and cores were obtained by X-ray diffraction. Moreover, data of orbital remote sensing were used in order to detect and quantify suspended matter by applying a logarithmic algorithm. Geochemical data of bottom sediments and cores revealed that, excepting Ba and Pb, the elements analyzed presented concentrations characteristic of an unpolluted ecosystem (Al: 0,25 - 8,76 %; Ba: 3,03 - 870 µg.g-1; Cd: < 0,25 µg.g-1; Cr: 1,72 - 82,4 µg.g-1; Cu: 0,12 -25,3 µg.g-1; Pb: 0,38 - 23,7 µg.g-1; Fe: 0,10 - 5,82 %; Mn: 15,1 - 815 µg.g-1; Ni: 0,14 - 36,1 µg.g-1; Zn: 1,37 - 113 µg.g-1). During the dry season a distribution pattern was observed, with higher metal concentrations in the margins, decreasing toward the central portion of the channel. These metal concentrations were well correlated with mineralogical compositions, with clay minerals prevailing at the margins, and quartz and feldspar in the center. However, this pattern was not observed during the wet season, probably because of the high water flux that disturbed bottom sediments. But, as observed for the dry season, a good correlation between metal concentrations and mineralogical composition was also observed for the wet season, with high metal concentrations where there were high quantities of clay minerals. Low enrichment ratios were obtained for the majority of elements analyzed, excepting for Mn, Ba and Pb. Manganese presented the higher ratios downstream for both seasons, and it can be an evidence of anthropogenic impact by shrimp farming. As barium and lead concentrations in sediment samples presented analytical problems during the total sample digestion, one cannot be sure that the ratios obtained correspond to the reality. The highest metal concentrations in particulate matter were obtained in the portion dominated by fluvial transport for all metals analyzed, excepting for copper. Barium and zinc were the only elements that presented elevated concentrations that are not common of unpolluted ecosystems (Ba: 5730 - 8355 µg.g-1; Zn: 3899 - 4348 µg.g-1). However, these high concentrations could not be related to the shrimp farming and waste waters from the town of Canguaretama, once they were obtained from the fluvial particulate matter, that is upstream from the activities above mentioned. The application of the logarithmic algorithm to the processed LANDSAT image was well succeeded, although the acquired image does not correspond exactly to the field campaigns. The IKONOS image provided very detailed views of the suspended sediment concentration at the estuary, as the mixture of distinct water flows at the confluence of Cunhaú and Curimataú rivers, with more turbid waters from Cunhaú river, that is directly affected by effluents from shrimp farming and urban waste waters deriving from the town of Canguaretama

Flame AAS determination of metal ions in fuel ethanol after preconcentration on acid carboxymethylcellulose (CMCH)

This paper describes the preparation of acid carboxymethylcellulose (CMCH), and the results of a study on the adsorption and preconcentration (using batch and flow-through column methods) of Cd(II), Cu(II), Cr(III), Fe(III), Ni(II) and Zn(II) in ethanol medium. The adsorption capacities for each metallic ion were (in mmol g(-1)) Cd(II) = 0.92; Cu(II) = 1.45; Cr(III) = 1.70; Fe(III) = 1.60; Ni(II) = 1.30; and Zn(II) = 1.10. By means of the flow-through method, a recovery of ca. 100% of the metallic ions adsorbed in a column packed with 2 g of CMCH was found when 5.0 mL of 1.0 mol L-1 hydrochloric acid were used as eluent. An enrichment factor of 20 (100 mt solution containing 50 mu g L-1 of the metallic ions, concentrated to 5.0 mt) was obtained by this preconcentration procedure. The sorption-desorption procedure applied allowed the development of a preconcentration and Flame AAS quantification method of metallic ions in fuel ethanol at trace levels.

Determination of Cu, Ni, and Zn in fuel ethanol by FAAS after enrichment in column packed with 2-aminothiazole-modified silica gel

This work describes the synthesis and characterization of 2-aminothiazole-modified silica gel (SiAT), as well as its application for preconcentration (in batch and column technique) of Cu(II), Ni(II) and Zn(II) in ethanol medium. The adsorption capacities of SiAT determined for each metal ion were (mmol g(-1)): Cu(II)=1.20, Ni(II)=1.10 and Zn(II)=0.90. In addition, results obtained in flow experiments, showed a recovery of ca. 100% of the metal ions adsorbed in a column packed with 500 mg of SiAT. The eluent was 2.0 mol L-1 HCl. The sorption-desorption of the studied metal ions made possible the development of a preconcentration method for metal ions at trace level in fuel ethanol using flame AAS for their quantification.

Heavy metals in Oxisols amended with biosolids and cropped with maize in a long-term experiment

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal studies of solid 4-chlorobenzylidenepyruvates of heavy lanthanides(III) and yttrium(III)

Solid-state compounds of general formula LnL(3).2H(2)O, where Ln is heavier trivalent lanthanides and yttrium, L is 4-chlorobenzylidenepyruvate have been synthetised.On heating these compounds decompose in steps. They lose the hydration water in the first step and the thermal decomposition of the anhydrous compounds occurs with the formation of oxochloride (Eu, Gd); mixture of oxide and oxochloride that decrease with increasing of atomic number of metal (Tb-Tm); or oxide (Yb, Lu, Y) as final residue, up to 900degreesC. The dehydration enthalpies found for terbium, holmium, ytterbium and yttrium compounds were: 34.93, 42.40, 57.39 and 62.24 kJ mol(-1), respectively.

Thiobacillus ferrooxidans response to copper and other heavy metals: growth, protein synthesis and protein phosphorylation

Respirometric experiments demonstrated that the oxygen uptake by Thiobacillus ferrooxidans strain LR was not inhibited in the presence of 200 mM copper. Copper-treated and untreated cells from this T. ferrooxidans strain were used in growth experiments in the presence of cadmium, copper, nickel and zinc. Growth in the presence of copper was improved by the copper-treated cells. However, no growth was observed for these cells, within 190 h of culture, when cadmium, nickel and zinc were added to the media. Changes in the total protein synthesis pattern were detected by two-dimensional polyacrylamide gel electrophoresis for T. ferrooxidans LR cells grown in the presence of different heavy metals. Specific proteins were induced by copper (16, 28 and 42 kDa) and cadmium (66 kDa), whereas proteins that had their synthesis repressed were observed for all the heavy metals tested. Protein induction was also observed in the cytosolic and membrane fractions from T. ferrooxidans LR cells grown in the presence of copper. The level of protein phosphorylation was increased in the presence of this metal.

Sorption and preconcentration of metal ions in ethanol solution with a silica gel surface chemically modified with benzimidazole

The adsorption isotherms of MCl(2) (M = Mn, Ni, Cu, Zn and Cd) and FeCl3 by silica gel chemically modified with benzimidazole molecules (= SI(CH2)(3)-NC7H5N) were studied in ethanol solution at 298 K. A column made of modified silica was used to adsorb and preconcentrate the above metal ions from ethanol solution. Elution was done with 0.1 M hydrochloric acid in an ethanol/water mixture having a mole fraction of water of 0.8. The material was applied in the preconcentration of metal ions from commercial ethanol normally used as engine fuel.

The use of silica-immobilized brown alga (Pilayella littoralis) for metal preconcentration and determination by inductively coupled plasma optical emission spectrometry

The brown alga Pilayella littoralis was used as a new biosorbent in an on-line metal preconcentration procedure in a flow-injection system. Al, Co, Cu and Fe were determined in lake water samples by inductively coupled plasma optical emission spectrometry (ICP-OES) after preconcentration in a silica-immobilized alga column. Like other algae, P. littoralis exhibited strong affinity for these metals proving to be an effective accumulation medium. Metals were bound at pH 5.5 and were displaced at pH < 2 with diluted HCl. The enrichment factors for Cu-II, Fe-III, Al-III and Co-II were 13, 7, 16 and 11, respectively. Metal sorption efficiency ranged from 86 to 90%. The method accuracy was assessed by using drinking water certified reference material and graphite furnace atomic absorption spectrometry (GFAAS) as a comparison technique. The column procedure allowed a less time consuming, easy regeneration of the biomaterial and rigidity of the alga provided by its immobilization on silica gel. (C) 2003 Elsevier B.V. All rights reserved.