Aspectos técnicos, econômicos e de sustentabilidade da produção de hidrogênio renovável

Pós-graduação em Engenharia Mecânica - FEG

A novel method for power quality multiple disturbance decomposition based on Independent Component Analysis

In this paper, a novel method for power quality signal decomposition is proposed based on Independent Component Analysis (ICA). This method aims to decompose the power system signal (voltage or current) into components that can provide more specific information about the different disturbances which are occurring simultaneously during a multiple disturbance situation. The ICA is originally a multichannel technique. However, the method proposes its use to blindly separate out disturbances existing in a single measured signal (single channel). Therefore, a preprocessing step for the ICA is proposed using a filter bank. The proposed method was applied to synthetic data, simulated data, as well as actual power system signals, showing a very good performance. A comparison with the decomposition provided by the Discrete Wavelet Transform shows that the proposed method presented better decoupling for the analyzed data. (C) 2012 Elsevier Ltd. All rights reserved.

Nondetection Index of Anti-Islanding Passive Protection of Synchronous Distributed Generators

Synchronous distributed generators are prone to operate islanded after contingencies, which is usually not allowed due to safety and power-quality issues. Thus, there are several anti-islanding techniques; however, most of them present technical limitations so that they are likely to fail in certain situations. Therefore, it is important to quantify and determine whether the scheme under study is adequate or not. In this context, this paper proposes an index to evaluate the effectiveness of anti-islanding frequency-based relays commonly used to protect synchronous distributed generators. The method is based on the calculation of a numerical index that indicates the time period that the system is unprotected against islanding considering the global period of analysis. Although this index can precisely be calculated based on several electromagnetic transient simulations, a practical method is also proposed to calculate it directly from simple analytical formulas or lookup tables. The results have shown that the proposed approach can assist distribution engineers to assess and set anti-islanding protection schemes.

Estudio y análisis de las necesidades computacionales de un parque eólico

[ES] La energía eólica es una de las fuentes de energía renovable más importante hoy día con un continuo crecimiento a nivel mundial. España también ha apostado por las renovables y más concretamente por la energía eólica, materializándose con importantes instalaciones en gran parte de las comunidades autónomas entre ellas, Canarias. Con la realización de este trabajo se pretende estudiar el potencial eólico disponible en la zona donde se pretenda instalar o mantener un parque eólico, empleando para ello la ayuda de un supercomputador, el cual se encargará, por medio de un software de predicción meteorológica, que ayudarán en la decisión de dónde ubicar un parque eólico y, posteriormente, en la fase de explotación, predecir la potencia que un parque eólico inyectará en la red eléctrica con la antelación suficiente para que permita planificar las centrales de reserva de generación de energía tradicional u otras acciones que se consideren de interés. Durante el desarrollo del trabajo emplearemos el software “WRF” de predicción meteorológica. Esto generará un alto coste computacional y es por lo que proponemos realizar los cálculos empleando la ayuda de un supercomputador. Para concluir el trabajo mostraremos las características del supercomputador Atlante, situado en Las Palmas de Gran Canaria, y analizaremos el coste que le supondría a una empresa, la compra o el alquiler de un supercomputador.

Theoretical and Experimental Analysis of micro-CHP Energy Systems

In the framework of the micro-CHP (Combined Heat and Power) energy systems and the Distributed Generation (GD) concept, an Integrated Energy System (IES) able to meet the energy and thermal requirements of specific users, using different types of fuel to feed several micro-CHP energy sources, with the integration of electric generators of renewable energy sources (RES), electrical and thermal storage systems and the control system was conceived and built. A 5 kWel Polymer Electrolyte Membrane Fuel Cell (PEMFC) has been studied. Using experimental data obtained from various measurement campaign, the electrical and CHP PEMFC system performance have been determinate. The analysis of the effect of the water management of the anodic exhaust at variable FC loads has been carried out, and the purge process programming logic was optimized, leading also to the determination of the optimal flooding times by varying the AC FC power delivered by the cell. Furthermore, the degradation mechanisms of the PEMFC system, in particular due to the flooding of the anodic side, have been assessed using an algorithm that considers the FC like a black box, and it is able to determine the amount of not-reacted H2 and, therefore, the causes which produce that. Using experimental data that cover a two-year time span, the ageing suffered by the FC system has been tested and analyzed.

Merkmalsbezogene Verifikation hochaufgelöster Niederschlagsvorhersagen für Deutschland

Die Verifikation bewertet die Güte von quantitativen Niederschlagsvorhersagen(QNV) gegenüber Beobachtungen und liefert Hinweise auf systematische Modellfehler. Mit Hilfe der merkmals-bezogenen Technik SAL werden simulierte Niederschlagsverteilungen hinsichtlich (S)truktur, (A)mplitude und (L)ocation analysiert. Seit einigen Jahren werden numerische Wettervorhersagemodelle benutzt, mit Gitterpunktabständen, die es erlauben, hochreichende Konvektion ohne Parametrisierung zu simulieren. Es stellt sich jetzt die Frage, ob diese Modelle bessere Vorhersagen liefern. Der hoch aufgelöste stündliche Beobachtungsdatensatz, der in dieser Arbeit verwendet wird, ist eine Kombination von Radar- und Stationsmessungen. Zum einem wird damit am Beispiel der deutschen COSMO-Modelle gezeigt, dass die Modelle der neuesten Generation eine bessere Simulation des mittleren Tagesgangs aufweisen, wenn auch mit zu geringen Maximum und etwas zu spätem Auftreten. Im Gegensatz dazu liefern die Modelle der alten Generation ein zu starkes Maximum, welches erheblich zu früh auftritt. Zum anderen wird mit dem neuartigen Modell eine bessere Simulation der räumlichen Verteilung des Niederschlags, durch eine deutliche Minimierung der Luv-/Lee Proble-matik, erreicht. Um diese subjektiven Bewertungen zu quantifizieren, wurden tägliche QNVs von vier Modellen für Deutschland in einem Achtjahreszeitraum durch SAL sowie klassischen Maßen untersucht. Die höher aufgelösten Modelle simulieren realistischere Niederschlagsverteilungen(besser in S), aber bei den anderen Komponenten tritt kaum ein Unterschied auf. Ein weiterer Aspekt ist, dass das Modell mit der gröbsten Auf-lösung(ECMWF) durch den RMSE deutlich am besten bewertet wird. Darin zeigt sich das Problem des ‚Double Penalty’. Die Zusammenfassung der drei Komponenten von SAL liefert das Resultat, dass vor allem im Sommer das am feinsten aufgelöste Modell (COSMO-DE) am besten abschneidet. Hauptsächlich kommt das durch eine realistischere Struktur zustande, so dass SAL hilfreiche Informationen liefert und die subjektive Bewertung bestätigt. rnIm Jahr 2007 fanden die Projekte COPS und MAP D-PHASE statt und boten die Möglich-keit, 19 Modelle aus drei Modellkategorien hinsichtlich ihrer Vorhersageleistung in Südwestdeutschland für Akkumulationszeiträume von 6 und 12 Stunden miteinander zu vergleichen. Als Ergebnisse besonders hervorzuheben sind, dass (i) je kleiner der Gitter-punktabstand der Modelle ist, desto realistischer sind die simulierten Niederschlags-verteilungen; (ii) bei der Niederschlagsmenge wird in den hoch aufgelösten Modellen weniger Niederschlag, d.h. meist zu wenig, simuliert und (iii) die Ortskomponente wird von allen Modellen am schlechtesten simuliert. Die Analyse der Vorhersageleistung dieser Modelltypen für konvektive Situationen zeigt deutliche Unterschiede. Bei Hochdrucklagen sind die Modelle ohne Konvektionsparametrisierung nicht in der Lage diese zu simulieren, wohingegen die Modelle mit Konvektionsparametrisierung die richtige Menge, aber zu flächige Strukturen realisieren. Für konvektive Ereignisse im Zusammenhang mit Fronten sind beide Modelltypen in der Lage die Niederschlagsverteilung zu simulieren, wobei die hoch aufgelösten Modelle realistischere Felder liefern. Diese wetterlagenbezogene Unter-suchung wird noch systematischer unter Verwendung der konvektiven Zeitskala durchge-führt. Eine erstmalig für Deutschland erstellte Klimatologie zeigt einen einer Potenzfunktion folgenden Abfall der Häufigkeit dieser Zeitskala zu größeren Werten hin auf. Die SAL Ergebnisse sind für beide Bereiche dramatisch unterschiedlich. Für kleine Werte der konvektiven Zeitskala sind sie gut, dagegen werden bei großen Werten die Struktur sowie die Amplitude deutlich überschätzt. rnFür zeitlich sehr hoch aufgelöste Niederschlagsvorhersagen gewinnt der Einfluss der zeitlichen Fehler immer mehr an Bedeutung. Durch die Optimierung/Minimierung der L Komponente von SAL innerhalb eines Zeitfensters(+/-3h) mit dem Beobachtungszeit-punkt im Zentrum ist es möglich diese zu bestimmen. Es wird gezeigt, dass bei optimalem Zeitversatz die Struktur und Amplitude der QNVs für das COSMO-DE besser werden und damit die grundsätzliche Fähigkeit des Modells die Niederschlagsverteilung realistischer zu simulieren, besser gezeigt werden kann.

Biogas and bio-hydrogen: production and uses. A review

The first part of this essay aims at investigating the already available and promising technologies for the biogas and bio-hydrogen production from anaerobic digestion of different organic substrates. One strives to show all the peculiarities of this complicate process, such as continuity, number of stages, moisture, biomass preservation and rate of feeding. The main outcome of this part is the awareness of the huge amount of reactor configurations, each of which suitable for a few types of substrate and circumstance. Among the most remarkable results, one may consider first of all the wet continuous stirred tank reactors (CSTR), right to face the high waste production rate in urbanised and industrialised areas. Then, there is the up-flow anaerobic sludge blanket reactor (UASB), aimed at the biomass preservation in case of highly heterogeneous feedstock, which can also be treated in a wise co-digestion scheme. On the other hand, smaller and scattered rural realities can be served by either wet low-rate digesters for homogeneous agricultural by-products (e.g. fixed-dome) or the cheap dry batch reactors for lignocellulose waste and energy crops (e.g. hybrid batch-UASB). The biological and technical aspects raised during the first chapters are later supported with bibliographic research on the important and multifarious large-scale applications the products of the anaerobic digestion may have. After the upgrading techniques, particular care was devoted to their importance as biofuels, highlighting a further and more flexible solution consisting in the reforming to syngas. Then, one shows the electricity generation and the associated heat conversion, stressing on the high potential of fuel cells (FC) as electricity converters. Last but not least, both the use as vehicle fuel and the injection into the gas pipes are considered as promising applications. The consideration of the still important issues of the bio-hydrogen management (e.g. storage and delivery) may lead to the conclusion that it would be far more challenging to implement than bio-methane, which can potentially “inherit” the assets of the similar fossil natural gas. Thanks to the gathered knowledge, one devotes a chapter to the energetic and financial study of a hybrid power system supplied by biogas and made of different pieces of equipment (natural gas thermocatalitic unit, molten carbonate fuel cell and combined-cycle gas turbine structure). A parallel analysis on a bio-methane-fed CCGT system is carried out in order to compare the two solutions. Both studies show that the apparent inconvenience of the hybrid system actually emphasises the importance of extending the computations to a broader reality, i.e. the upstream processes for the biofuel production and the environmental/social drawbacks due to fossil-derived emissions. Thanks to this “boundary widening”, one can realise the hidden benefits of the hybrid over the CCGT system.

Integrated solar energy and absorption cooling model for HVAC (heating, ventilating, and air conditioning) applications in buildings

The demands in production and associate costs at power generation through non renewable resources are increasing at an alarming rate. Solar energy is one of the renewable resource that has the potential to minimize this increase. Utilization of solar energy have been concentrated mainly on heating application. The use of solar energy in cooling systems in building would benefit greatly achieving the goal of non-renewable energy minimization. The approaches of solar energy heating system research done by initiation such as University of Wisconsin at Madison and building heat flow model research conducted by Oklahoma State University can be used to develop and optimize solar cooling building system. The research uses two approaches to develop a Graphical User Interface (GUI) software for an integrated solar absorption cooling building model, which is capable of simulating and optimizing the absorption cooling system using solar energy as the main energy source to drive the cycle. The software was then put through a number of litmus test to verify its integrity. The litmus test was conducted on various building cooling system data sets of similar applications around the world. The output obtained from the software developed were identical with established experimental results from the data sets used. Software developed by other research are catered for advanced users. The software developed by this research is not only reliable in its code integrity but also through its integrated approach which is catered for new entry users. Hence, this dissertation aims to correctly model a complete building with the absorption cooling system in appropriate climate as a cost effective alternative to conventional vapor compression system.

Computational simulations of latent heat thermal energy storage systems - with innovative and first-principles based simulation for the underlying unsteady melting (and solidification) processes

This thesis develops an effective modeling and simulation procedure for a specific thermal energy storage system commonly used and recommended for various applications (such as an auxiliary energy storage system for solar heating based Rankine cycle power plant). This thermal energy storage system transfers heat from a hot fluid (termed as heat transfer fluid - HTF) flowing in a tube to the surrounding phase change material (PCM). Through unsteady melting or freezing process, the PCM absorbs or releases thermal energy in the form of latent heat. Both scientific and engineering information is obtained by the proposed first-principle based modeling and simulation procedure. On the scientific side, the approach accurately tracks the moving melt-front (modeled as a sharp liquid-solid interface) and provides all necessary information about the time-varying heat-flow rates, temperature profiles, stored thermal energy, etc. On the engineering side, the proposed approach is unique in its ability to accurately solve – both individually and collectively – all the conjugate unsteady heat transfer problems for each of the components of the thermal storage system. This yields critical system level information on the various time-varying effectiveness and efficiency parameters for the thermal storage system.

Development and simulation of DSP filters for transformer differential protection / by Oskar Reynisson.

Transformer protection is one of the most challenging applications within the power system protective relay field. Transformers with a capacity rating exceeding 10 MVA are usually protected using differential current relays. Transformers are an aging and vulnerable bottleneck in the present power grid; therefore, quick fault detection and corresponding transformer de-energization is the key element in minimizing transformer damage. Present differential current relays are based on digital signal processing (DSP). They combine DSP phasor estimation and protective-logic-based decision making. The limitations of existing DSP-based differential current relays must be identified to determine the best protection options for sensitive and quick fault detection. The development, implementation, and evaluation of a DSP differential current relay is detailed. The overall goal is to make fault detection faster without compromising secure and safe transformer operation. A detailed background on the DSP differential current relay is provided. Then different DSP phasor estimation filters are implemented and evaluated based on their ability to extract desired frequency components from the measured current signal quickly and accurately. The main focus of the phasor estimation evaluation is to identify the difference between using non-recursive and recursive filtering methods. Then the protective logic of the DSP differential current relay is implemented and required settings made in accordance with transformer application. Finally, the DSP differential current relay will be evaluated using available transformer models within the ATP simulation environment. Recursive filtering methods were found to have significant advantage over non-recursive filtering methods when evaluated individually and when applied in the DSP differential relay. Recursive filtering methods can be up to 50% faster than non-recursive methods, but can cause false trip due to overshoot if the only objective is speed. The relay sensitivity is however independent of filtering method and depends on the settings of the relay’s differential characteristics (pickup threshold and percent slope).

Statistical methods for multi-marker testing in genetic association studies

As the development of genotyping and next-generation sequencing technologies, multi-marker testing in genome-wide association study and rare variant association study became active research areas in statistical genetics. This dissertation contains three methodologies for association study by exploring different genetic data features and demonstrates how to use those methods to test genetic association hypothesis. The methods can be categorized into in three scenarios: 1) multi-marker testing for strong Linkage Disequilibrium regions, 2) multi-marker testing for family-based association studies, 3) multi-marker testing for rare variant association study. I also discussed the advantage of using these methods and demonstrated its power by simulation studies and applications to real genetic data.

Heterogeneous Collaborative Sensor Network for Electrical Management of an Automated House with PV Energy

In this paper we present a heterogeneous collaborative sensor network for electrical management in the residential sector. Improving demand-side management is very important in distributed energy generation applications. Sensing and control are the foundations of the “Smart Grid” which is the future of large-scale energy management. The system presented in this paper has been developed on a self-sufficient solar house called “MagicBox” equipped with grid connection, PV generation, lead-acid batteries, controllable appliances and smart metering. Therefore, there is a large number of energy variables to be monitored that allow us to precisely manage the energy performance of the house by means of collaborative sensors. The experimental results, performed on a real house, demonstrate the feasibility of the proposed collaborative system to reduce the consumption of electrical power and to increase energy efficiency.

Use of STATCOM in wind farms with fixed-speed generators for grid code compliance

The increasing penetration of wind energy into power systems has pushed grid operators to set new requirements for this kind of generating plants in order to keep acceptable and reliable operation of the system. In addition to the low voltage ride through capability, wind farms are required to participate in voltage support, stability enhancement and power quality improvement. This paper presents a solution for wind farms with fixed-speed generators based on the use of STATCOM with braking resistor and additional series impedances, with an adequate control strategy. The focus is put on guaranteeing the grid code compliance when the wind farm faces an extensive series of grid disturbances.

UPM Activities on the STLs processing (Task 6.2) and the generation of DPA cross section library up to 150 MeV (Task 4.1)

Generation of a complete damage energy and dpa cross section library up to 150 MeVbased on JEFF- 3.1.1 and suitable approximations (UPM) Postprocessing of photonuclear libraries (by CCFE) and thermal scattering  tables (by UPM) at the backend of the calculational system (CCFE/UPM)

Parque eólico Cassino

La energía eólica, así como otras energías renovables, ha experimentado en la última década un gran auge que va extendiéndose alrededor de todo el mundo, cada vez más concienciado de la importancia de las energías renovables como una fuente alternativa de energía. Se han sumado al reto todos los países acogidos al Protocolo de Kyoto, que a fin de reducir emisiones están potenciando la energía eólica como la fuente de energía renovable hoy día más viable para la generación eléctrica. Brasil alcanzó en 2011 los 1.509 MW instalados, lo que representa el 50% de Latinoamérica, seguido por México con el 31%. Las características del sector eléctrico así como un marco legal favorable y el alto potencial eólico, hacen que la perspectiva de crecimiento en este tipo de energía sea muy favorable durante los próximos años, con estimaciones de unos 20.000 MW para 2020. El asentamiento del sector en el país de algunos de los fabricantes más importantes y los avances en cuanto a eficiencia de los aerogeneradores, mayor aprovechamiento de la energía de los vientos menos intensos, amplía las posibles ubicaciones de parques eólicos permitiendo una expansión grande del sector. El parque eólico objeto del proyecto está ubicado en el estado de Rio Grande do Sul, al sur del país, y está constituido por 33 aerogeneradores de 2,0 MW de potencia unitaria, lo que supone una potencia total instalada de 66 MW. La energía eléctrica generada en él será de 272,8 GWh/año. Esta energía se venderá mediante un contrato de compraventa de energía (PPA, Power Purchase Agreement) adjudicado por el gobierno Brasileño en sus sistemas de subasta de energía. En el proyecto se aborda primeramente la selección del emplazamiento del parque eólico a partir de datos de viento de la zona. Estos datos son estudiados para evaluar el potencial eólico y así poder optimizar la ubicación de las turbinas eólicas. Posteriormente se evalúan varios tipos de aerogeneradores para su implantación en el emplazamiento. La elección se realiza teniendo en cuenta las características técnicas de las máquinas y mediante un estudio de la productividad del parque con el aerogenerador correspondiente. Finalmente se opta por el aerogenerador G97-2.0 de GAMESA. La ejecución técnica del parque eólico se realiza de forma que se minimicen los impactos ambientales y de acuerdo a lo establecido en el Estudio de Impacto Ambiental realizado. Este proyecto requiere una inversión de 75,4 M€, financiada externamente en un 80 % y el 20 % con recursos propios del promotor. Del estudio económico-financiero se deduce que el proyecto diseñado es rentable económicamente y viable, tanto desde el punto de vista técnico como financiero. Abstract Wind energy, as well as other renewable energies, has experienced over the last decade a boom that is spreading around the world increasingly aware of the importance of renewable energy as an alternative energy source. All countries that ratified the Kyoto Protocol have joined the challenge promoting wind energy in order to reduce emissions as the more feasible renewable energy for power generation. In 2011 Brazil reached 1509 MW installed, 50% of Latin America, followed by Mexico with 31%. Electric sector characteristics as well as a favorable legal framework and the high wind potential, make the perspective of growth in this kind of energy very positive in the coming years, with estimates of about 20,000 MW by 2020. Some leading manufacturers have settled in the country and improvements in wind turbines efficiency with less intense winds, make higher the number of possible locations for wind farms allowing a major expansion of the sector. The planned wind farm is located in the state of Rio Grande do Sul, in the south of the Brazil, and is made up of 33 wind turbines of 2,0 MW each, representing a total capacity of 66 MW. The electricity generated, 272,8 GWh/year will be sold through a power purchase agreement (PPA) awarded by the Brazilian government in its energy auction systems. The project deals with the site selection of the wind farm from wind data in the area. These data are studied to evaluate the wind potential and thus optimize the location of wind turbines. Then several types of turbines are evaluated for implementation at the site. The choice is made taking into account the technical characteristics of the machines and a study of the productivity of the park with the corresponding turbine. Finally selected wind turbine is Gamesa G97-2.0. The technical implementation of the wind farm is done to minimize environmental impacts as established in the Environmental Impact Study. This project requires an investment of 75,4 M€, financed externally by 80% and 20% with equity from the promoter. The economic-financial study shows that the project is economically viable, both technically and financially.