Phenol-furfural resins to elaborate composites, reinforced with sisal fibers - Molecular analysis of resin and properties of composites

Resol type resins were prepared in alkaline conditions (potassium hydroxide or potassium carbonate) using furfural obtained by acid hydrolysis of abundant renewable resources from agricultural and forestry waste residues. The structures of the resins were fully determined by H-1, C-13, and 2D NMR spectrometries with the help of four models compounds synthesized specially for this study. MALDI-Tof mass spectrometry experiments indicated that a majority of linear oligomers and a minority of cyclic ones constituted them. Composites were prepared with furfural-phenol resins and sisal fibers. These fibers were chosen mainly because they came from natural lignocellulosic material and they presented excellent mechanical microscopy images indicated that the composites displayed excellent adhesion between resin and fibers. Impact strength measurement showed that mild conditions were more suitable to prepare thermosets. Nevertheless, mild conditions induced a high-diffusion coefficient for water absorption by composites. Composites with good properties could be prepared using high proportion of materials obtained from biomass without formaldehyde. (c) 2008 Wiley Periodicals, Inc.

Hydrogen peroxide and supercritical carbon dioxide: a new bleaching stage for Eucalyptus kraft-O(2) pulps

Kraft pulp is currently bleached largely by the elemental chlorine free (ECF) technology with oxygen, chlorine dioxide, and hydrogen as active agents. This technology brought about significant environmental improvements in relation to standard processes based on chlorine gas and hypochlorite, but there is still need for further improvements. This study presents a novel environmentally friendly bleaching stage - the so-called `hydrogen peroxide in supercritical carbon dioxide`, P((SC-CO2)) - that can be adapted to current ECF bleaching processes, with preference in cases where hydrogen peroxide is already used. In this study, the P((SC-CO2)) stage was evaluated as a replacement to the last peroxide stage of the D(EP)DP bleaching sequence and to the first peroxide stage of the D(EP)DP sequence, for an oxygen delignified eucalypt kraft-O(2) pulp. The P((SC-CO2)) stage was run with 0.5% hydrogen peroxide, at 15% consistency, 70 degrees C, and 73 bar. The reaction time was 30 min. The performances of regular P stages and the new P((SC-CO2)) stage were compared. Promising results were observed with the DEP((SC-CO2))DP sequence; the P((SC-CO2)) decreased kappa number from 2.7 to 2.1, and the hexenuronic acid groups from 17.0 to 12.4 mmol kg(-1). The P((SC-CO2)) stage showed poor performance when applied in the D(EP)DP((SC-CO2)) sequence. It is concluded that the process presents potential but requires further optimization to improve selectivity and efficiency.

The value of a saved tree : The lifecycle of CO2-emissions associated with the combination of printing paper and electricity production of wood in the U.S. and Sweden

The pulp- and paper production is a very energy intensive industry sector. Both Sweden and the U.S. are major pulpandpaper producers. This report examines the energy and the CO2-emission connected with the pulp- and paperindustry for the two countries from a lifecycle perspective.New technologies make it possible to increase the electricity production in the integrated pulp- andpaper mill through black liquor gasification and a combined cycle (BLGCC). That way, the mill canproduce excess electricity, which can be sold and replace electricity produced in power plants. In thisprocess the by-products that are formed at the pulp-making process is used as fuel to produce electricity.In pulp- and paper mills today the technology for generating energy from the by-product in aTomlinson boiler is not as efficient as it could be compared to the BLGCC technology. Scenarios havebeen designed to investigate the results from using the BLGCC technique using a life cycle analysis.Two scenarios are being represented by a 1994 mill in the U.S. and a 1994 mill in Sweden.The scenariosare based on the average energy intensity of pulp- and paper mills as operating in 1994 in the U.S.and Sweden respectively. The two other scenarios are constituted by a »reference mill« in the U.S. andSweden using state-of-the-art technology. We investigate the impact of varying recycling rates and totalenergy use and CO2-emissions from the production of printing and writing paper. To economize withthe wood and that way save trees, we can use the trees that are replaced by recycling in a biomassgasification combined cycle (BIGCC) to produce electricity in a power station. This produces extra electricitywith a lower CO2 intensity than electricity generated by, for example, coal-fired power plants.The lifecycle analysis in this thesis also includes the use of waste treatment in the paper lifecycle. Both Sweden and theU.S. are countries that recycle paper. Still there is a lot of paper waste, this paper is a part of the countries municipalsolid waste (MSW). A lot of the MSW is landfilled, but parts of it are incinerated to extract electricity. The thesis hasdesigned special scenarios for the use of MSW in the lifecycle analysis.This report is studying and comparing two different countries and two different efficiencies on theBLGCC in four different scenarios. This gives a wide survey and points to essential parameters to specificallyreflect on, when making assumptions in a lifecycle analysis. The report shows that there arethree key parameters that have to be carefully considered when making a lifecycle analysis of wood inan energy and CO2-emission perspective in the pulp- and paper mill in the U.S. and in Sweden. First,there is the energy efficiency in the pulp- and paper mill, then the efficiency of the BLGCC and last theCO2 intensity of the electricity displaced by BIGCC or BLGCC generatedelectricity. It also show that with the current technology that we havetoday, it is possible to produce CO2 free paper with a waste paper amountup to 30%. The thesis discusses the system boundaries and the assumptions.Further and more detailed research, including amongst others thesystem boundaries and forestry, is recommended for more specificanswers.

Flit, fylleri och förbundsstatspotential : En undersökning av den nyzeeländska Sverigebilden i samband med skandinaviska emigranters ankomst till Wellington år 1871

This Bachelor’s thesis elucidates the subject of Swedish migration to New Zealand in 1871. Drawing on the work of Anthony Grigg, who has assessed the public opinions regarding the arrival of Scandinavians in 1871-1876, this study aims to highlight the image of Sweden and Swedes conveyed in New Zealand at this time. Through a hermeneutic engagement with newspapers of the day, it is concluded that Swedes in general were being portrayed as industrious, thrifty and well suited for the forestry labour expected of them. It is also shown, however, that Swedes and Sweden to a limited extent were being associated with notorious drinking habits and inferior intellectual abilities. Furthermore, the study highlights what appears to have been a medial difficulty to differentiate between Swedes and Norwegians.

The attractiveness of the work is affected when production of handcrafted log houses moves indoors

Viewed from a historical perspective, a shift has occurred within the forestry and wood sector towards indoor work. In Sweden, the production of handcrafted log houses has now also begun to move indoors. With a point of departure in development processes within the log house sector involving working indoors, education, work attractiveness, between 2001-2005, the aim of this study was to compare indoor work with outdoor work, based on log house builders' experience of working on handcrafted log houses. Methods used in the interactive development project involving apprentices, experienced log house builders and researchers, were participation with continuous documentation of experiences and opinions; questions; interviews; and measurement of the work environment. The Attractive Work Model has been used in order to analyse perceptions and values. The changes, 15 out of 22 areas, were perceived both negatively and positively. Therefore, it can not be said that working on traditional, handcrafted log houses becomes more attractive if it is moved indoors. The majority wanted to work both outdoors and indoors, while most of the others only wanted to work outdoors. The results indicate that there is scope for developing more attractive work indoors by utilising experiences from log house builders and closely related activities such as the forestry and wood sector. Changes made within one area of work attractiveness affect other areas. Further research is needed both with regard to comparisons between indoor and outdoor work and regarding the interaction between the areas that are identified in the Attractive Work Model.

Outdoor performance of forest seedlings pre-cultivated under artificial lights : effects of the light spectra used for pre-cultivation on the future establishment and development

Forest nurseries are essential for producing good quality seedlings, thus being a key element in the reforestation process. With increasing climate change awareness, nursery managers are looking for new tools that can help reduce the effects of their operations on the environment. The ZEPHYR project, funded by the European Commission under the Seventh Framework Programme (FP7), has the objective of finding new alternatives for nurseries by developing innovative zero-impact technologies for forest plant production. Due to their direct relationship to the energy consumption of the nurseries, one of the main elements addressed are the grow lights used for the pre-cultivation. New LED luminaires with a light spectrum tailored to the seedlings’ needs are being studied and compared against the traditional fluorescent lamps. Seedlings of Picea abies and Pinus sylvestris were grown under five different light spectra (one fluorescent and 4 LED) during 5 weeks with a photoperiod of 16 hours at 100 μmol∙m-2∙s-1 and 60% humidity. In order to evaluate if these seedlings were able cope with real field stress conditions, a forest field trial was also designed. The terrain chosen was a typical planting site in mid-Sweden after clear-cutting. Two vegetation periods after the outplanting, the seedlings that were pre-cultivated under the LED lamps have performed at least as well as those that were grown under fluorescent lights. These results show that there is a good  potential for lightning substitution in forestry nurseries.

Protection of spruce seedlings against pine weevil attacks by treatment of seeds or seedlings with nicotinamide, nicotinic acid and jasmonic acid

Sustainable methods are required to protect newly planted tree seedlings from insect herbivore attack. To this end, here Norway spruce (Picea abies (L.) Karst.) seeds were treated with 2.5 mM nicotinamide (NIC), 2.5 mM nicotinic acid (NIA), 3 mM jasmonic acid (JA) or 0.2 mM 5-azacytidine (5-Aza), and 6-month-old seedlings grown from these seeds were planted at a reforestation area in central Sweden. Attack by pine weevils (Hylobius abietis) was reduced by 50 per cent by NIC treatment, 62.5 per cent by JA treatment and 25 per cent by 5-Aza treatment, when compared with seedlings grown from untreated seeds. Watering 18-month-old spruce seedlings with 2 mM NIC or 2 mM NIA did reduce attack during the first season in the field by 40 and 53 per cent, respectively, compared with untreated plants. Girdling was also reduced by the different treatments. Analysis of conifer seedlings treated with 5-Aza points at a possible involvement of epigenetic mechanisms in this defensive capacity. This is supported by a reduced level of DNA methylation in the needles of young spruce seedlings grown in a greenhouse from NIC-treated seeds. Seed treatment for seedling defense potentiation is simple, inexpensive and also a new approach for forestry with many potential applications.

High female mortality resulting in herd collapse in free-ranging domesticated reindeer (Rangifer tarandus tarandus) in Sweden

Reindeer herding in Sweden is a form of pastoralism practised by the indigenous Sami population. The economy is mainly based on meat production. Herd size is generally regulated by harvest in order not to overuse grazing ranges and keep a productive herd. Nonetheless, herd growth and room for harvest is currently small in many areas. Negative herd growth and low harvest rate were observed in one of two herds in a reindeer herding community in Central Sweden. The herds (A and B) used the same ranges from April until the autumn gathering in October-December, but were separated on different ranges over winter. Analyses of capture-recapture for 723 adult female reindeer over five years (2007-2012) revealed high annual losses (7.1% and 18.4%, for herd A and B respectively). A continuing decline in the total reindeer number in herd B demonstrated an inability to maintain the herd size in spite of a very small harvest. An estimated breakpoint for when herd size cannot be kept stable confirmed that the observed female mortality rate in herd B represented a state of herd collapse. Lower calving success in herd B compared to A indicated differences in winter foraging conditions. However, we found only minor differences in animal body condition between the herds in autumn. We found no evidence that a lower autumn body mass generally increased the risk for a female of dying from one autumn to the next. We conclude that the prime driver of the on-going collapse of herd B is not high animal density or poor body condition. Accidents or disease seem unlikely as major causes of mortality. Predation, primarily by lynx and wolverine, appears to be the most plausible reason for the high female mortality and state of collapse in the studied reindeer herding community.

Influência das principais commodities agropecuárias e de variáveis macroeconômicas sobre os preços da terra agrícola no Brasil

Este trabalho tem como proposta investigar como o preço de terras de uso rural no Brasil é afetado pelos preços e exportações das principais commodities agropecuárias, bem como por variáveis macroeconômicas, como taxa básica de juros, taxa de câmbio, taxa de inflação e disponibilidade de crédito agrícola. Para tal foram consideradas as produções agrícola de algodão, café, cana-de-açúcar (e seus principais produtos açúcar e etanol), milho e soja, a produção pecuária de carne bovina e a produção industrial de celulose de fibra curta com foco em sua principal matéria prima, os plantios reflorestados de eucalipto. Em linha com estudos anteriores, foi encontrada evidência empírica de que o preço da terra possui cointegração com algumas das variáveis agrícolas, pecuárias e florestais citadas, em especial em estados com maior vocação agropecuária e/ou para silvicultura. Quanto às variáveis macroeconômicas, apenas a taxa básica de juros apresentou cointegração com o preço de terras para todos os estados avaliados, taxa de câmbio e disponibilidade de crédito rural não aparecem como variáveis estatisticamente significantes. Conclui-se que, para estados com notável participação na balança comercial brasileira de produtos agrossilvipastoris, é possível obter um modelo de equilibro de longo prazo entre o preço da terra de uso rural e as variáveis destacadas acima, de modo que investidores do setor possam utilizá-lo como ferramenta de projeção no auxílio da tomada de decisão além de avaliar potenciais impactos no valor de seus ativos A inovação do presente estudo está em testar as hipóteses de cointegração para cada um dos estados da federação.

Desenvolvimento, sustentabilidade e conservação da biodiversidade na amazônia: a produção familiar agroextrativista em áreas protegidas no sul do amapá

The establishment of Extractivism and Sustainable Development Reserves comes from an amazon forestry people resistance initiative. It means an option of natural resources management as protected areas for agroextractivism purposes. According to the institutional point of view, these lands, called Conservation Unity for Sustainable Exploration, belong to the government which grants the usufruct rights to the agroextractivist families under a sharing territory administration agreement among government and rural communities. The main roles of these lands are both: to improve the dwellers wellbeing, and protecting the local biodiversity. Additionally, they also represent the start of this thesis theme entitled Development, sustainability, and biodiversity conservation in the Amazon region: the use of protected areas for agroextractivism domestic yield in south of Amapá state with the objective of analyzing the performance that each territory has been reaching in terms of the attributions proposed at the beginning, when they were created. Social, economics, and environment changes that occurred in the agroextractivist areas have been evaluated from two selected test sites, named Rio Cajari Extractivist Reserve and Rio Iratapuru Sustainable Reserve, both, localized in the south of Amapá state

Análise quali-quantitativa da arborização na praça XV de novembro em Ribeirão Preto - SP, Brasil

A Praça XV de Novembro, implantada em meados do século XIX, tem grande valor histórico-cultural, além de se constituir em uma das principais áreas verdes do centro da cidade de Ribeirão Preto. Visando ao conhecimento detalhado da vegetação para fins de orientação do manejo e conservação dessa área, foi feito um levantamento quali-quantitativo e fitossociológico das árvores e palmeiras da praça. Foram medidas altura e Diâmetro à Altura do Peito (DAP) e identificados todos os indivíduos de porte arbóreo (árvores e palmeiras) presentes na Praça, em nível de espécie. A praça ocupa uma área de 15.456,00 m², onde foram amostradas 42 espécies distribuídas por 19 famílias, num total de 161 indivíduos. Apesar de o local apresentar arborização com alto índice de diversidade de espécies (Shannon-Weaver de 3,14), os exemplares necessitam de maior atenção quanto a problemas ligados à fitossanidade e podas adequadas, fazendo que resulte em espaço seguro para os frequentadores e em boa qualidade paisagística.

Dinâmica populacional do psilídeo-de-concha Glycaspis brimblecombei (Moore, 1964) (Hemiptera: Psyllidae) e de seu parasitóide Psyllaephagus bliteus (Hymenoptera: Encyrtidae) em floresta de Eucalyptus camaldulensis

O psilídeo-de-concha, Glycaspis brimblecombei, é uma praga exótica específica de Eucalyptus, que causa desfolha, secamento de ponteiros e ramos, podendo levar as árvores à morte. O parasitóide Psyllaephagus bliteus é indicado como principal agente no controle biológico desta praga. Portanto, o monitoramento adequado de as ambas espécies por um método eficiente de amostragem facilitaria o manejo para uma futura tomada de decisão. Devido à falta de informações referentes ao seu comportamento em plantações extensivas de eucalipto no Brasil, este trabalho teve como objetivo estudar as populações de G. brimblecombei e de P. bliteus em florestas de Eucalyptus camaldulensis, utilizando armadilhas amarelas para determinação de sua flutuação populacional e correlacionado-as com variáveis meteorológicas (temperatura e precipitação). A determinação da flutuação populacional (53 pontos amostrais) foi realizada em talhão de 19ha com E. camaldulensis em Luíz Antônio, SP, em 10avaliações quinzenais, entre janeiro e junho de 2005. As populações de ambas as espécies apresentaram correlação inversamente proporcional em função da temperatura e não há correlação com a precipitação no período avaliado.

DNA bar-coding reveals source and patterns of Thaumastocoris peregrinus invasions in South Africa and South America

Thaumastocoris peregrinus is a recently introduced invertebrate pest of non-native Eucalyptus plantations in the Southern Hemisphere. It was first reported from South Africa in 2003 and in Argentina in 2005. Since then, populations have grown explosively and it has attained an almost ubiquitous distribution over several regions in South Africa on 26 Eucalyptus species. Here we address three key questions regarding this invasion, namely whether only one species has been introduced, whether there were single or multiple introductions into South Africa and South America and what the source of the introduction might have been. To answer these questions, bar-coding using mitochondrial DNA (COI) sequence diversity was used to characterise the populations of this insect from Australia, Argentina, Brazil, South Africa and Uruguay. Analyses revealed three cryptic species in Australia, of which only T. peregrinus is represented in South Africa and South America. Thaumastocoris peregrinus populations contained eight haplotypes, with a pairwise nucleotide distance of 0.2-0.9% from seventeen locations in Australia. Three of these haplotypes are shared with populations in South America and South Africa, but the latter regions do not share haplotypes. These data, together with the current distribution of the haplotypes and the known direction of original spread in these regions, suggest that at least three distinct introductions of the insect occurred in South Africa and South America before 2005. The two most common haplotypes in Sydney, one of which was also found in Brisbane, are shared with the non-native regions. Sydney populations of T. peregrinus, which have regularly reached outbreak levels in recent years, might thus have served as source of these three distinct introductions into other regions of the Southern Hemisphere.

Trichospilus diatraeae Cherian & Margabandhu, 1942 (Hymenoptera: Eulophidae), a new parasitoidof Melanolophia consimilaria (Lepidoptera: Geometridae)

First report on the parasitoid Trichospilus diatraeae of the genus in Eulophidae found in the field parasitizing pupae of the eucalyptus defoliating looper Melanolophia consimilaria. This opens new perspectives for the use of this parasitoid in biological control programs against caterpillars of forestry importance.

Caracterização da Estrutura Espacial do Psilídeo-de-concha Glycaspis brimblecombei (Hemiptera: Psyllidae) e de seu Parasitóide Psyllaephagus bliteus (Hymenoptera: Encyrtidae) em Floresta de Eucalyptus camaldulensis

Os psilídeos são um grupo de pragas amplamente distribuídas, causando perdas consideráveis em sistemas agrícolas e florestais. A recente descoberta da ocorrência do psilídeo-de-concha Glycaspis brimblecombei Moore (Hemiptera: Psyllidae), no Brasil tornou-se um problema de grande importância, por ser específico de Eucalyptus. O parasitóide Psyllaephagus bliteus Riek (Hymenoptera: Encyrtidae) é indicado como principal agente no controle biológico desta praga. Portanto, para o monitoramento adequado de ambas espécies é necessário um método eficiente de amostragem. Devido a falta de informações referentes ao seu comportamento em plantações extensivas de eucalipto, realizou-se este trabalho, para verificar a distribuição espacial de G. brimblecombei e de seu parasitóide P. bliteus, através de armadilhas adesivas em floresta de E. camaldulensis. Para determinação da distribuição espacial foram utilizadas 53 armadilhas amarelas distribuídas uniformemente no talhão, formando uma grade amostral espaçadas de 50 x 36 m, à altura aproximada de 1,80 m do solo. Cada armadilha foi presa com auxílio de um arame plastificado em um fio estendido entre duas árvores em um talhão de 19 ha com E. camaldulensis em Luiz Antônio, SP. Foram realizadas dez avaliações, entre janeiro e junho de 2005. Após a coleta as armadilhas foram levadas ao laboratório para ser feita à triagem e contagem do número total de adultos de G. brimblecombei e de P. bliteus, nas duas faces das armadilhas. Concluiu-se que as populações de ambas espécies apresentaram distribuição espacial agregada, no período avaliado.