Synthesis Methodology Applied to a Tunable Patch Filter With Independent Frequency and Bandwidth Control

A new methodology for the synthesis of tunable patch filters is presented. The methodology helps the designer to perform a theoretical analysis of the filter through a coupling matrix that includes the effect of the tuning elements used to tune the filter. This general methodology accounts for any tuning parameter desired and was applied to the design of a tunable dual-mode patch filter with independent control of center frequency and bandwidth (BW). The bandpass filter uses a single triangular resonator with two etched slots that split the fundamental degenerate modes and form the filter passband. Varactor diodes assembled across the slots are used to vary the frequency of each degenerate fundamental mode independently, which is feasible due to the nature of the coupling scheme of the filter. The varactor diode model used in simulations, their assembling, the dc bias configuration, and measured results are presented. The theory results are compared to the simulations and to measurements showing a very good agreement and validating the proposed methodology. The fabricated filter presents an elliptic response with 20% of center frequency tuning range around 3.2 GHz and a fractional BW variation from 4% to 12% with low insertion loss and high power handling with a 1-dB compression point higher than +14.5 dB.

CONTROL OF GLYPHOSATE RESISTANT HAIRY FLEABANE (Conyza bonariensis) WITH DICAMBA AND 2,4-D

Auxyn type herbicides such as dicamba and 2,4-D are alternative herbicides that can be used to control glyphosate-resistant hairy fleabane. With the forthcoming possibility of releasing dicamba-resistant and 2,4-D-resistant crops, use of these growth regulator herbicides will likely be an alternative that can be applied to the control of glyphosate resistant hairy fleabane (Conyza bonariensis). The objective of this research was to model the efficacy, through dose-response curves, of glyphosate, 2,4-D, isolated dicamba and glyphosate-dicamba combinations to control a brazilian hairy fleabane population resistant to glyphosate. The greenhouse dose-response studies were conducted as a completely randomized experimental design, and the rates used for dose response curve construction were 0, 120, 240, 480, 720 and 960 ga.i. ha(-1) for 2,4-D, dicamba and the dicamba combination, with glyphosate at 540 g a. e. ha(-1). The rates for glyphosate alone were 0, 180, 360, 540, 720 and 960 g a. e. ha(-1). Herbicides were applied when the plants were in a vegetative stage with 10 to 12 leaves and height between 12 and 15 cm. Hairy fleabane had low sensitivity to glyphosate, with poor control even at the 960 g a. e. ha(-1) rate. Dicamba and 2,4-D were effective in controlling the studied hairy fleabane. Hairy fleabane responds differently to 2,4-D and dicamba. The combination of glyphosate and dicamba was not antagonistic to hairy fleabane control, and glyphosate may cause an additive effect on the control, despite the population resistance.

Modeling of active holonic control systems for intelligent buildings

Building facilities have become important infrastructures for modern productive plants dedicated to services. In this context, the control systems of intelligent buildings have evolved while their reliability has evidently improved. However, the occurrence of faults is inevitable in systems conceived, constructed and operated by humans. Thus, a practical alternative approach is found to be very useful to reduce the consequences of faults. Yet, only few publications address intelligent building modeling processes that take into consideration the occurrence of faults and how to manage their consequences. In the light of the foregoing, a procedure is proposed for the modeling of intelligent building control systems, considersing their functional specifications in normal operation and in the of the event of faults. The proposed procedure adopts the concepts of discrete event systems and holons, and explores Petri nets and their extensions so as to represent the structure and operation of control systems for intelligent buildings under normal and abnormal situations. (C) 2012 Elsevier B.V. All rights reserved.

Influence of pattern gradation on the design of piezocomposite energy harvesting devices using topology optimization

Piezoelectric materials can be used to convert oscillatory mechanical energy into electrical energy. Energy harvesting devices are designed to capture the ambient energy surrounding the electronics and convert it into usable electrical energy. The design of energy harvesting devices is not obvious, requiring optimization procedures. This paper investigates the influence of pattern gradation using topology optimization on the design of piezocomposite energy harvesting devices based on bending behavior. The objective function consists of maximizing the electric power generated in a load resistor. A projection scheme is employed to compute the element densities from design variables and control the length scale of the material density. Examples of two-dimensional piezocomposite energy harvesting devices are presented and discussed using the proposed method. The numerical results illustrate that pattern gradation constraints help to increase the electric power generated in a load resistor and guides the problem toward a more stable solution. (C) 2012 Elsevier Ltd. All rights reserved.

Phase-Locked loops lock-in range in Frequency Modulated-Atomic Force Microscope nonlinear control system

Since the mid 1980s the Atomic Force Microscope is one the most powerful tools to perform surface investigation, and since 1995 Non-Contact AFM achieved true atomic resolution. The Frequency-Modulated Atomic Force Microscope (FM-AFM) operates in the dynamic mode, which means that the control system of the FM-AFM must force the micro-cantilever to oscillate with constant amplitude and frequency. However, tip-sample interaction forces cause modulations in the microcantilever motion. A Phase-Locked loop (PLL) is used to demodulate the tip-sample interaction forces from the microcantilever motion. The demodulated signal is used as the feedback signal to the control system, and to generate both topographic and dissipation images. As a consequence, a proper design of the PLL is vital to the FM-AFM performance. In this work, using bifurcation analysis, the lock-in range of the PLL is determined as a function of the frequency shift (Q) of the microcantilever and of the other design parameters, providing a technique to properly design the PLL in the FM-AFM system. (C) 2011 Elsevier B.V. All rights reserved.

Exercise training improves neurovascular control and functional capacity in heart failure patients regardless of age

Background: Exercise training is a non-pharmacological strategy for treatment of heart failure. Exercise training improves functional capacity and quality of life in patients. Moreover, exercise training reduces muscle sympathetic nerve activity (MSNA) and peripheral vasoconstriction. However, most of these studies have been conducted in middle-aged patients. Thus, the effects of exercise training in older patients are much less understood. The present study was undertaken to investigate whether exercise training improves functional capacity, muscular sympathetic activation and muscular blood flow in older heart failure patients, as it does in middle-aged heart failure patients. Design: Fifty-two consecutive outpatients with heart failure from the database of the Unit of Cardiovascular Rehabilitation and Physiology Exercise were divided by age (middle-aged, defined as 45-59 years, and older, defined as 60-75 years) and exercise status (trained and untrained). Methods: MSNA was recorded directly from the peroneal nerve using the microneurography technique. Forearm Blood Flow (FBF) was measured by venous occlusion plethysmography. Functional capacity was evaluated by cardiopulmonary exercise test. Results: Exercise training significantly and similarly increased FBF and peak VO2 in middle-aged and older heart failure patients. In addition, exercise training significantly and similarly reduced MSNA and forearm vascular resistance in these patients. No significant changes were found in untrained patients. Conclusion: Exercise training improves neurovascular control and functional capacity in heart failure patients regardless of age.

Postural control in elderly women with osteoporosis: comparison of balance, strengthening and stretching exercises. A randomized controlled trial

Objective: To compare the efficacy of balance training associated with muscle strengthening or stretching, relative to no intervention, in the postural control of elderly women with osteoporosis. Design: A randomized, controlled trial. Subjects and interventions: Sample consisted of 50 women aged 65 years or older, with osteoporosis, randomized into one of three groups: strengthening group (n = 17) performed balance training with muscle strengthening; stretching group (n = 17) performed balance training with stretching; and control group (n = 16), no activities. Interventions lasted eight weeks, twice a week, 60 minutes a day. Main measures: Postural control was evaluated by the modified Clinical Test of Sensory Interaction for Balance (CTSIBm) and Limits of Stability Test. Strength was assessed by dynamometry and the shortening of the hamstrings by goniometry. Results: Relative to controls, participants in the strengthening group displayed significantly increased dorsiflexion strength and knee flexion strength, as well as centre of pressure velocity, directional control, and oscillation velocity (CTSIBm test). The stretching group had significantly improvements in hamstring length, knee flexion strength, centre of pressure velocity, and amplitude of movements. Relative to the stretching group, the strengthening group yielded better knee extension strength and directional control. Conclusion: The results suggest that both interventions are effective in improving postural control when compared to the control group, and the strengthening group was superior to the stretching group in knee extension strength and in directional control.

Differentiation of African Components of Ancestry to Stratify Groups in a Case-Control Study of a Brazilian Urban Population

Background: Balancing the subject composition of case and control groups to create homogenous ancestries between each group is essential for medical association studies. Methods: We explored the applicability of single-tube 34-plex ancestry informative markers (AIM) single nucleotide polymorphisms (SNPs) to estimate the African Component of Ancestry (ACA) to design a future case-control association study of a Brazilian urban sample. Results: One hundred eighty individuals (107 case group; 73 control group) self-described as white, brown-intermediate or black were selected. The proportions of the relative contribution of a variable number of ancestral population components were similar between case and control groups. Moreover, the case and control groups demonstrated similar distributions for ACA <0.25 and >0.50 categories. Notably a high number of outlier values (23 samples) were observed among individuals with ACA <0.25. These individuals presented a high probability of Native American and East Asian ancestral components; however, no individuals originally giving these self-described ancestries were observed in this study. Conclusions: The strategy proposed for the assessment of ancestry and adjustment of case and control groups for an association study is an important step for the proper construction of the study, particularly when subjects are taken from a complex urban population. This can be achieved using a straight forward multiplexed AIM-SNPs assay of highly discriminatory ancestry markers.

Postural Control in Older Patients with Benign Paroxysmal Positional Vertigo

Objective. To evaluate the effectiveness of a canalith-repositioning procedure in postural control of older patients with idiopathic benign paroxysmal positional vertigo (BPPV). Study Design. Prospective clinical trial. Setting. A tertiary referral center. Methods. A 9-month follow-up survey with a prospective design was conducted among 33 older patients with BPPV. Patients underwent static posturography (Balance Rehabilitation Unit [BRU]) and were administered the Dizziness Handicap Inventory (DHI) before and after the maneuver. After the treatment, they were compared with 33 healthy older subjects. The posturography parameters were the limit of stability (LOS), the center of body-pressure area (COP), and the velocity of oscillation (VOS) under conditions of visual, somatosensory, and visual-vestibular conflict. Results. One canalith-repositioning procedure relieved most patients' complaints (54.5%), and 100% were relieved with 1 to 3 maneuvers. Total DHI score and all subscales improved after treatment (P < .01). The LOS values pretreatment (mean [SD] 134.27 [55.32] cm(2)) and posttreatment (181.03 [47.79] cm(2)) were significantly different (P < .01). Comparative analysis of COP values showed a relevant statistical difference in 8 of 10 postmaneuver conditions (P < .01). The postmaneuver VOS showed a significant difference under 7 conflict conditions. There were no differences between the healthy older subjects and treated patients for all VOS values under all conditions and for COP values under 9 conditions. Conclusion. The canalith-repositioning procedure promotes remission of symptoms, an increase in LOS, and improvement in postural control under conditions of somatosensory and visual conflict and visual-vestibular interaction.

Factors associated with maternal intrapartum transfers from a freestanding birth centre in Sao Paulo, Brazil: A case control study

Objectives: to identify factors associated with maternal intrapartum transfer from a freestanding birth centre to hospital. Design: case-control study with retrospective data collection. Participants and settings: cases included all 111 women transferred from a freestanding birth centre in Sao Paulo to the referral hospital, from March 2002 to December 2009. The controls were 456 women who gave birth in the birth centre during the same period who were not transferred, randomly selected with four controls for each case. Methods: data were obtained from maternal records. Factors associated with maternal intrapartum transfers were initially analysed using a chi(2) test of association. Variables with p < 0.20 were then included in multivariate analyses. A multiple logistic regression model was built using stepwise forward selection; variables which reached statistical significance at p < 0.05 were considered to be independently associated with maternal transfer. Findings: during the study data collection period, 111(4%) of 2,736 women admitted to the centre were transferred intrapartum. Variables identified as independently associated factors for intrapartum transfer included nulliparity (OR 5.1, 95% CI 2.7-9.8), maternal age >= 35 years (OR 5.4, 95% CI 2.1-13.4), not having a partner (OR 2.8, 95% CI 1.5-5.3), cervical dilation <= 3 cm on admission to the birth centre (OR 1.9, 95% CI 1.1-3.2) and between 5 and 12 antenatal appointments at the birth centre (OR 3.8, 95% CI 1.9-7.5). In contrast, a low correlation between fundal height and pregnancy gestation (OR 0.3, 95% CI 0.2-0.6) appeared to be protective against transfer. Conclusions and implications for practice: identifying factors associated with maternal intrapartum transfer could support decision making by women considering options for place of birth, and support the content of appropriate information about criteria for admission to a birth centre. Findings add to the evidence base to support identification of women in early labour who may experience later complications and could support timely implementation of appropriate interventions associated with reducing transfer rates. (C) 2012 Elsevier Ltd. All rights reserved.

Design of laminated piezocomposite shell transducers with arbitrary fiber orientation using topology optimization approach

Sensor and actuator based on laminated piezocomposite shells have shown increasing demand in the field of smart structures. The distribution of piezoelectric material within material layers affects the performance of these structures; therefore, its amount, shape, size, placement, and polarization should be simultaneously considered in an optimization problem. In addition, previous works suggest the concept of laminated piezocomposite structure that includes fiber-reinforced composite layer can increase the performance of these piezoelectric transducers; however, the design optimization of these devices has not been fully explored yet. Thus, this work aims the development of a methodology using topology optimization techniques for static design of laminated piezocomposite shell structures by considering the optimization of piezoelectric material and polarization distributions together with the optimization of the fiber angle of the composite orthotropic layers, which is free to assume different values along the same composite layer. The finite element model is based on the laminated piezoelectric shell theory, using the degenerate three-dimensional solid approach and first-order shell theory kinematics that accounts for the transverse shear deformation and rotary inertia effects. The topology optimization formulation is implemented by combining the piezoelectric material with penalization and polarization model and the discrete material optimization, where the design variables describe the amount of piezoelectric material and polarization sign at each finite element, with the fiber angles, respectively. Three different objective functions are formulated for the design of actuators, sensors, and energy harvesters. Results of laminated piezocomposite shell transducers are presented to illustrate the method. Copyright (C) 2012 John Wiley & Sons, Ltd.

Rationale, study design, and analysis plan of the Alveolar Recruitment for ARDS Trial (ART): Study protocol for a randomized controlled trial

Background: Acute respiratory distress syndrome (ARDS) is associated with high in-hospital mortality. Alveolar recruitment followed by ventilation at optimal titrated PEEP may reduce ventilator-induced lung injury and improve oxygenation in patients with ARDS, but the effects on mortality and other clinical outcomes remain unknown. This article reports the rationale, study design, and analysis plan of the Alveolar Recruitment for ARDS Trial (ART). Methods/Design: ART is a pragmatic, multicenter, randomized (concealed), controlled trial, which aims to determine if maximum stepwise alveolar recruitment associated with PEEP titration is able to increase 28-day survival in patients with ARDS compared to conventional treatment (ARDSNet strategy). We will enroll adult patients with ARDS of less than 72 h duration. The intervention group will receive an alveolar recruitment maneuver, with stepwise increases of PEEP achieving 45 cmH(2)O and peak pressure of 60 cmH2O, followed by ventilation with optimal PEEP titrated according to the static compliance of the respiratory system. In the control group, mechanical ventilation will follow a conventional protocol (ARDSNet). In both groups, we will use controlled volume mode with low tidal volumes (4 to 6 mL/kg of predicted body weight) and targeting plateau pressure <= 30 cmH2O. The primary outcome is 28-day survival, and the secondary outcomes are: length of ICU stay; length of hospital stay; pneumothorax requiring chest tube during first 7 days; barotrauma during first 7 days; mechanical ventilation-free days from days 1 to 28; ICU, in-hospital, and 6-month survival. ART is an event-guided trial planned to last until 520 events (deaths within 28 days) are observed. These events allow detection of a hazard ratio of 0.75, with 90% power and two-tailed type I error of 5%. All analysis will follow the intention-to-treat principle. Discussion: If the ART strategy with maximum recruitment and PEEP titration improves 28-day survival, this will represent a notable advance to the care of ARDS patients. Conversely, if the ART strategy is similar or inferior to the current evidence-based strategy (ARDSNet), this should also change current practice as many institutions routinely employ recruitment maneuvers and set PEEP levels according to some titration method.

Control of glyphosate resistant hairy fleabane (Conyza bonariensis) with dicamba and 2,4-D

Auxyn type herbicides such as dicamba and 2,4-D are alternative herbicides that can be used to control glyphosate-resistant hairy fleabane. With the forthcoming possibility of releasing dicamba-resistant and 2,4-D-resistant crops, use of these growth regulator herbicides will likely be an alternative that can be applied to the control of glyphosate resistant hairy fleabane (Conyza bonariensis). The objective of this research was to model the efficacy, through dose-response curves, of glyphosate, 2,4-D, isolated dicamba and glyphosatedicamba combinations to control a brazilian hairy fleabane population resistant to glyphosate. The greenhouse dose-response studies were conducted as a completely randomized experimental design, and the rates used for dose response curve construction were 0, 120, 240, 480, 720 and 960 g a.i. ha-1 for 2,4-D, dicamba and the dicamba combination, with glyphosate at 540 g a.e. ha-1. The rates for glyphosate alone were 0, 180, 360, 540, 720 and 960 g a.e. ha-1. Herbicides were applied when the plants were in a vegetative stage with 10 to 12 leaves and height between 12 and 15 cm. Hairy fleabane had low sensitivity to glyphosate, with poor control even at the 960 g a.e. ha-1 rate. Dicamba and 2,4-D were effective in controlling the studied hairy fleabane. Hairy fleabane responds differently to 2,4-D and dicamba. The combination of glyphosate and dicamba was not antagonistic to hairy fleabane control, and glyphosate may cause an additive effect on the control, despite the population resistance.

Biomarkers and Bacterial Pneumonia Risk in Patients with Treated HIV Infection: A Case-Control Study

Background: Despite advances in HIV treatment, bacterial pneumonia continues to cause considerable morbidity and mortality in patients with HIV infection. Studies of biomarker associations with bacterial pneumonia risk in treated HIVinfected patients do not currently exist. Methods: We performed a nested, matched, case-control study among participants randomized to continuous combination antiretroviral therapy (cART) in the Strategies for Management of Antiretroviral Therapy trial. Patients who developed bacterial pneumonia (cases) and patients without bacterial pneumonia (controls) were matched 1:1 on clinical center, smoking status, age, and baseline cART use. Baseline levels of Club Cell Secretory Protein 16 (CC16), Surfactant Protein D (SP-D), C-reactive protein (hsCRP), interleukin-6 (IL-6), and d-dimer were compared between cases and controls. Results: Cases (n = 72) and controls (n = 72) were 25.7% female, 51.4% black, 65.3% current smokers, 9.7% diabetic, 36.1% co-infected with Hepatitis B/C, and 75.0% were on cART at baseline. Median (IQR) age was 45 (41, 51) years with CD4+ count of 553 (436, 690) cells/mm3. Baseline CC16 and SP-D were similar between cases and controls, but hsCRP was significantly higher in cases than controls (2.94 mg/mL in cases vs. 1.93 mg/mL in controls; p = 0.02). IL-6 and d-dimer levels were also higher in cases compared to controls, though differences were not statistically significant (p-value 0.06 and 0.10, respectively). Conclusions: In patients with cART-treated HIV infection, higher levels of systemic inflammatory markers were associated with increased bacterial pneumonia risk, while two pulmonary-specific inflammatory biomarkers, CC16 and SP-D, were not associated with bacterial pneumonia risk.

Risk factors associated with death in Brazilian children with severe dengue: a case-control study

Objective: The purpose of this case-control study was to evaluate risk factors associated with death in children with severe dengue. Methods: The clinical condition of hospitalized patients with severe dengue who died (cases, n = 18) was compared with that of hospitalized patients with severe dengue who survived (controls, n = 77). The inclusion criteria for this study were age under 13 years; hospital admission in São Luis, northeastern Brazil; and laboratory-confirmed diagnosis of dengue. Results: Severe bleeding (hemoptysis), a defining criterion for dengue severity, was the factor most strongly associated with death in our study. We also found that epistaxis and persistent vomiting, both included as warning signs in the World Health Organization (WHO) classification of dengue, were strongly associated with death. No significant association was observed between any of the laboratory findings and death. Conclusions: The finding that epistaxis and persistent vomiting were also associated with death in children with severe dengue was unexpected and deserves to be explored in future studies. Because intensive care units are often limited in resource-poor settings, any information that can help to distinguish patients with severe dengue with a higher risk to progress to death may be crucial.