In what extent can a segmented packaging make children choose healthier breakfast cereals?

Field lab in marketing: Children consumer behaviour

Non-gyrator type active inductors

Modern CMOS radio frequency (RF) Receivers have enabled efficient and increasing applications. The main requirement is to have system in a single chip, in order to minimize area and cost. For the purpose it is required the development of inductorless circuits for the key blocks of an RF receiver. Examples of this key blocks are RC oscillators, RF band pass filters, and Low Noise Amplifiers. The present dissertation presents an inductorless wideband MOSFET-only RF Non-Gyrator Type of Active Inductors with low area, low cost, and very low power, capable of covering the whole WMTS, and ISM, band and intended for biomedical applications. The proposed circuit is based on a floating capacitor connected between two controlled current sources. The first current source, which is controlled by the circuit input voltage, has two objectives: supply current to the capacitor (

Analysis and implementation of a multi-ratio switched capacitor DC-DC converter for a supercapacitor power supply

An energy harvesting system requires an energy storing device to store the energy retrieved from the surrounding environment. This can either be a rechargeable battery or a supercapcitor. Due to the limited lifetime of rechargeable batteries, they need to be periodically replaced. Therefore, a supercapacitor, which has ideally a limitless number of charge/discharge cycles can be used to store the energy; however, a voltage regulator is required to obtain a constant output voltage as the supercapacitor discharges. This can be implemented by a Switched-Capacitor DC-DC converter which allows a complete integration in CMOS technology, although it requires several topologies in order to obtain a high efficiency. This thesis presents the complete analysis of four different topologies in order to determine expressions that allow to design and determine the optimum input voltage ranges for each topology. To better understand the parasitic effects, the implementation of the capacitors and the non-ideal effect of the switches, in 130 nm technology, were carefully studied. With these two analysis a multi-ratio SC DC-DC converter was designed with an output power of 2 mW, maximum efficiency of 77%, and a maximum output ripple, in the steady state, of 23 mV; for an input voltage swing of 2.3 V to 0.85 V. This proposed converter has four operation states that perform the conversion ratios of 1/2, 2/3, 1/1 and 3/2 and its clock frequency is automatically adjusted to produce a stable output voltage of 1 V. These features are implemented through two distinct controller circuits that use asynchronous time machines (ASM) to dynamically adjust the clock frequency and to select the active state of the converter. All the theoretical expressions as well as the behaviour of the whole system was verified using electrical simulations.

8-Phase Ring oscillator for modern receivers

The evolution of receiver architectures, built in modern CMOS technologies, allows the design of high efficient receivers. A key block in modern receivers is the oscillator. The main objective of this thesis is to design a very low power and low area 8-Phase Ring Oscillator for biomedical applications (ISM and WMTS bands). Oscillators with multiphase outputs and variable duty cycles are required. In this thesis we are focused in 12.5% and 50% duty-cycles approaches. The proposed circuit uses eight inverters in a ring structure, in order to generate the output duty cycle of 50%. The duty cycle of 1/8 is achieved through the combination of the longer duty cycle signals in pairs, using, for this purpose, NAND gates. Since the general application are not only the wireless communications context, as well as industrial, scientific and medical plans, the 8-Phase Oscillator is simulated to be wideband between 100 MHz and 1 GHz, and be able to operate in the ISM bands (447 MHz-930 MHz) and WMTS (600 MHz). The circuit prototype is designed in UMC 130 nm CMOS technology. The maximum value of current drawn from a DC power source of 1.2 V, at a maximum frequency of 930 MHz achieved, is 17.54 mA. After completion of the oscillator layout studied (occupied area is 165 μm x 83 μm). Measurement results confirm the expected operating range from the simulations, and therefore, that the oscillator fulfil effectively the goals initially proposed in order to be used as Local Oscillator in RF Modern Receivers.

The firm delocalization decision

In the current paper, the determinants of firm international relocation decision in twenty-six European countries during the period 2004-2014 are analyzed. We demonstrate, at light of three different but complementary theories that neoclassical, behavioural and institutional „push‟ factors have an impact in a firm decision-making process. Findings support that firm size, access to a global network, foreign capital, and negative internal growth in the workforce induce firm relocation. On the other hand, the degree of sunk assets has a negative effect on the probability of relocation. Delocalization decisions are also sector-dependent with low-tech manufacturing firms paying high salaries relocating abroad with a greater likelihood.

Auto-conceito no pré- escolar : Comparação das auto-percepções das crianças e as heteropercepções dos pais e educadores

Dissertação de Mestrado apresentada ao ISPA - Instituto Universitário

A utilização de terapias alternativas e complementares. Um estudo exploratório

Dissertação de Mestrado apresentada ao ISPA - Instituto Universitário

Quadrature generators based on ring oscillators and shift registers

Quadrature oscillators are key elements in modern radio frequency (RF) transceivers and very useful nowadays in wireless communications, since they can provide: low quadrature error, low phase-noise, and wide tuning range (useful to cover several bands). RC oscillators can be fully integrated without the need of external components (external high Q-inductors), optimizing area, cost, and power consumption. The conventional structure of ring oscillator offers poor frequency stability and phasenoise, low quality factor (Q), and besides being vulnerable to process, voltage and temperature (PVT) variations, its performance degrades as the frequency of operation increases. This thesis is devoted to quadrature oscillators and presents a detailed comparative study of ring oscillator and shift register (SR) approaches. It is shown that in SRs both phase-noise and phase error are reduced, while ring oscillators have the advantage of occupying less area and less consumption due to the reduced number of components in the circuit. Thus, although ring oscillators are more suitable for biomedical applications, SRs are more appropriate for wireless applications, especially when specification requirements are more stringent and demanding. The first architecture studied consists in a simple CMOS ring oscillator employing an odd number of static single-ended inverters as delay cells. Subsequently, the quadrature 4-stage ring oscillator concept is shown and post-layout simulations are presented. The 3 and 4-phase single-frequency local oscillator (LO) generators employing SRs are presented, the latter with 50% and 25% duty-cycles. The circuits operate at 600 MHz and 900 MHz, and were designed in a 130 nm standard CMOS technology with a voltage supply of 1.2 V.

Müllerian adenosarcoma of the uterus with sarcomatous overgrowth following tamoxifen treatment for breast cancer

Müllerian adenosarcoma with sarcomatous overgrowth presented by a 52-year-old female patient after adjuvant tamoxifen treatment for breast carcinoma is described. The diagnosis was made on histological basis after curettage and complementary total hysterectomy with bilateral salpingo-oophorectomy. The immunohistochemical study showed high expression of estrogen receptors in the epithelial component of the lesion and irregularly positive findings in the stroma. The proliferative activity evaluated by Ki-67 immunoexpression was higher in the stroma than the epithelium. Some of the stromal cells showed rhabdomyoblastic differentiation. The association of tamoxifen use and development of mesenchymal neoplasms is discussed.

Rehabilitation of renders of old buildings in Portugal: survey, supporting methodology proposal and case studies

The main purpose of the research is to present a proposal for a methodology to support the rehabilitation project of renders of old buildings. To achieve the objective it was considered essential to define the main types of participants and aspects to integrate the proposal. The research methodology consists in an inquiry presented to several professional participants in rehabilitation, a market study of materials and products available in Portugal, the design of a methodology proposal and its application to a case study. The inquiry sample totals 24 answers from the targeted professionals. A sequence of relevant supporting procedures consists in the proposal, which aims to provide a supporting methodology to decide and project in this context and also to be tested with its application to the building. This proposal was applied to an old building with load-bearing stone masonry walls and air-lime based renders. It was concluded that the assessment of the building and external renderings’ condition, its diagnosis and of the supporting walls, the definition of intervention, the specification of materials to be used and performance requirements to comply, and also plans for conservation and periodic maintenance, are crucial. From the inquiry, compatibility between materials and complementary roles and points of view of different types of participants in rehabilitation must be highlighted. A proposal for a methodology to support the project could provide useful guidance particularly for architects and construction engineers, and improve the understanding of direct participants on site, therefore contributing for the correct implementation of the intervention.

Long term (five-year) survival following radical surgical treatment plus adjuvant chemotherapy (FAM) in advanced gastric cancer: a controlled study

Several drugs and their associations are being used for adjuvant or complementary chemotherapy with the aim of improving results of gastric cancer treatment. The objective of this study was to verify the impact of these drugs on nutrition and on survival rate after radical treatment of 53 patients with gastric cancer in stage III of the TNM classification. A control group including 28 patients who had only undergone radical resection was compared to a group of 25 patients who underwent the same operative technique followed by adjuvant polychemotherapy with FAM (5-fluorouracil, Adriamycin, and mitomycin C). In this latter group, chemotherapy toxicity in relation to hepatic, renal, cardiologic, neurological, hematologic, gastrointestinal, and dermatological functions was also studied. There was no significant difference on admission between both groups in relation to gender, race, macroscopic tumoral type of tumor according to the Borrmann classification, location of the tumor in the stomach, length of the gastric resection, or response to cutaneous tests on delayed sensitivity. Chemotherapy was started on average, 2.3 months following surgical treatment. Clinical and laboratory follow-up of all patients continued for 5 years. The following conclusions were reached: 1) The nutritional status and incidence of gastrointestinal manifestation were similar in both groups; 2) There was no occurrence of cardiac, renal, neurological, or hepatic toxicity or death due to the chemotherapeutic method per se; 3) Dermatological alterations and hematological toxicity occurred exclusively in patients who underwent polychemotherapy; 4) There was no significant difference between the rate and site of tumoral recurrence, the disease-free interval, or the survival rate of both study groups; 5) Therefore, we concluded, after a 5-year follow-up, chemotherapy with the FAM regimen did not increase the survival rate.

The World Health Organization Multi-Professional Patient Safety Curriculum : implementation of key modules and its impact on patient safety knowledge, skills, and attitudes of medical students at the University of Algarve

ABSTRACT - Objectives: We attempted to show how the implementation of the key elements of the World Health Organization Patient Safety Curriculum Guide Multi-professional Edition in an undergraduate curriculum affected the knowledge, skills, and attitudes towards patient safety in a graduate entry Portuguese Medical School. Methods: After receiving formal recognition by the WHO as a Complementary Test Site and approval of the organizational ethics committee , the validated pre-course questionnaires measuring the knowledge, skills, and attitudes to patient safety were administered to the 2nd and3rd year students pursuing a four-year course (N = 46). The key modules of the curriculum were implemented over the academic year by employing a variety of learning strategies including expert lecturers, small group problem-based teaching sessions, and Simulation Laboratory sessions. The identical questionnaires were then administered and the impact was measured. The Curriculum Guide was evaluated as a health education tool in this context. Results: A significant number of the respondents, 47 % (n = 22), reported having received some form of prior patient safety training. The effect on Patient Safety Knowledge was assessed by using the percentage of correct pre- and post-course answers to construct 2 × 2 contingency tables and by applying Fishers’ test (two-tailed). No significant differences were detected (p < 0.05). To assess the effect of the intervention on Patient Safety skills and attitudes, the mean and standard deviation were calculated for the pre and post-course responses, and independent samples were subjected to Mann-Whitney’s test. The attitudinal survey indicated a very high baseline incidence of desirable attitudes and skills toward patient safety. Significant changes were detected (p < 0.05) regarding what should happen if an error is made (p = 0.016), the role of healthcare organizations in error reporting (p = 0.006), and the extent of medical error (p = 0.005). Conclusions: The implementation of selected modules of the WHO Patient Safety Curriculum was associated with a number of positive changes regarding patient safety skills and attitudes, with a baseline incidence of highly desirable patient safety attitudes, but no measureable change on the patient safety knowledge, at the University of Algarve Medical School. The significance of these results is discussed along with implications and suggestions for future research.

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.

Analysis and treatment of a nineteenth century portrait, study of Artsorb® and a proposal for a microclimate frame

The present work is divided in two parts: Part 1 is focused on the analysis and treatment of a 19th century portrait of Domingos Affonso, which belongs to the Ecomuseu Municipal do Seixal; and Part 2, which is entitled “The Microclimate Frame Project” is focused on the study of Artsorb® and on the planning of a microclimate frame for the painting. In Part 1, a study of the painting’s materials was performed using complementary analytical techniques and the painting’s condition was carefully evaluated. The painting exhibited signs of mould growth, and a more detailed investigation was made of this topic to understand if the fungal community was active and if it represented a real danger to the painting. A treatment was proposed, appropriate to the painting’s condition. A description of the treatment carried out, comprising the treatment options, is also present in this section. Within the study of the microclimate frame, in Part 2, the study of the potential corrosiveness of Artsorb® was a central subject. Artsorb® sheets are one of the most widely used materials for buffering relative humidity fluctuations in microclimate frames and its reported excellent performance is enhanced by its availability in lightweight sheets that can be easily placed inside microclimate frames. However, concerns have arisen regarding the presence of the corrosive salt lithium chloride in the composition of this buffer. Consequently, the present work also aimed to understand the potential risks of using Artsorb® and the possibility of avoiding exposure of lithium chloride to the artworks through the use of Tyvek®. Results from the preliminary tests seem to indicate that Artsorb® releases lithium chloride into air. This study also showed that a Tyvek® cover over Artsorb® reduces but does not eliminate evidence of chlorine contamination, and it significantly reduces the effectiveness of the buffering material. Considering that Artsorb® appears to be unsuitable due to the release of the corrosive salt, that Tyvek® was not efficient as a barrier for lithium chloride or as a permeable material to enable the proper functioning of Artsorb®, the buffering material proposed for the use in the microclimate frames is silica gel without indicator. Based on the choice of buffering material, as a result of this study, a microclimate frame is proposed.

Custos indirectos associados à obesidade em Portugal

RESUMO - A obesidade constitui um importante problema de saúde pública com consequências económicas de grande dimensão. Os obesos têm um risco acrescido de contrair doenças e de sofrer morte prematura devido a problemas como a diabetes, hipertensão arterial, AVC, insuficiência cardíaca e algumas neoplasias malignas. O presente estudo tem como objectivo estimar o custo económico indirecto (valor da produção perdida) associado à obesidade em Portugal no ano de 2002. O estudo adopta uma abordagem tipo custos da doença baseada na prevalência. Os dados são retirados do Inquérito Nacional de Saúde e estatísticas de rotina publicadas pelo INE e por outros organismos oficiais. Consideram-se como obesas pessoas com índice de massa corporal (IMC) ≥ 30 kg/m2 e estabelecem-se como limites etários para participação em actividades económicas produtivas as idades compreendidas entre os 15 e os 64 anos. A estratégia de imputação de custos ao factor de risco obesidade caracteriza- se por estimar, para a população portuguesa, as proporções de doença e morte prematura atribuíveis à obesidade e em multiplicar as estimativas populacionais encontradas pelo valor da produtividade económica potencial das pessoas afectadas. O custo indirecto total da obesidade em Portugal no ano de 2002 foi estimado em 199,8 milhões de euros. A mortalidade contribuiu com 58,4% deste valor (117 milhões de euros) e a morbilidade com 41,6% (83 milhões de euros). Os custos da morbilidade advêm de mais de 1,6 milhões de dias de incapacidade anuais, principalmente por faltas ao trabalho associadas a doenças do sistema circulatório e diabetes tipo II. Os custos da mortalidade são o resultado de 18 733 potenciais anos de vida activa perdidos, numa razão de 3 mortes masculinas por cada morte feminina. Os resultados indicam que a obesidade acarreta consideráveis perdas económicas para o país. Comparando os resultados com um estudo complementar que calculou os custos directos (em cuidados de saúde) da obesidade, verifica-se que a componente indirecta representa 40,2% do total dos custos da obesidade. A implementação de estratégias que prevenissem ou reduzissem a incidência e prevalência de obesidade em Portugal poderia gerar ganhos de produtividade elevados. Para conhecer a dimensão destes ganhos é necessária mais investigação sobre os benefícios clínicos e relação custo-efectividade de estratégias para a redução da obesidade.