Berries:emerging impact on cardiovascular health

Berries are a good source of polyphenols, especially anthocyanins, micronutrients, and fiber. In epidemiological and clinical studies, these constituents have been associated with improved cardiovascular risk profiles. Human intervention studies using chokeberries, cranberries, blueberries, and strawberries (either fresh, or as juice, or freeze-dried), or purified anthocyanin extracts have demonstrated significant improvements in LDL oxidation, lipid peroxidation, total plasma antioxidant capacity, dyslipidemia, and glucose metabolism. Benefits were seen in healthy subjects and in those with existing metabolic risk factors. Underlying mechanisms for these beneficial effects are believed to include upregulation of endothelial nitric oxide synthase, decreased activities of carbohydrate digestive enzymes, decreased oxidative stress, and inhibition of inflammatory gene expression and foam cell formation. Though limited, these data support the recommendation of berries as an essential fruit group in a heart-healthy diet.

The effect of nozzle geometry on the flow characteristics of small water jets

A wide variety of processes make use of plain orifice nozzles. Fuel injectors for internal combustion engines incorporate these nozzles to generate finely atomized sprays. Processes such as jet cutting, jet cleaning, and hydroentanglement, on the other hand, use similar nozzles, but require coherent jets. The spray or jet characteristics depend on the stability of the flow emerging from the orifice. This problem has been extensively researched for nozzles with diameters above 300 μm. Much less is known about the characteristics of jets produced by nozzles with smaller diameters, where viscous effects and small geometric variations due to manufacturing tolerances are likely to play an increasing role. Results are presented of a wide-ranging investigation of geometry effects on the flow parameters and jet characteristics of nozzles with diameters between 120 and 170 μm. Nozzles with circular cross-section and conical, cone-capillary and capillary axial designs were investigated. For conical and cone-capillary nozzles, the effect of cone angle and effects due to interactions between adjacent nozzles in the multi-hole cone-capillary nozzles were studied. For capillary nozzles, the effects of diameter variations and inlet edge roundness for capillary nozzles were considered. Furthermore, the effect of varying the aspect ratio (ratio of major and minor axes) of elliptical nozzles was studied. Flowrate and jet impact force measurements were carried out to determine the discharge coefficient C, velocity coefficient C, and contraction coefficient C of the nozzles for supply pressures between 3 and 12 MPa. Visualizations of the jet flow were carried out in the vicinity of the nozzle exit in order to identify near-nozzle flow regimes and to study jet coherence. The relationship between nozzle geometry, discharge characteristics, and jet coherence is examined. © IMechE 2006.

Shape stabilised phase change materials based on a high melt viscosity HDPE and paraffin waxes

Shape stabilised phase change materials (SSPCMs) based on a high density poly(ethylene)(hv-HDPE) with high (H-PW, Tm = 56–58 °C) and low (L-PW, Tm = 18–23 °C) melting point paraffin waxes were readily prepared using twin-screw extrusion. The thermo-physical properties of these materials were assessed using a combination of techniques and their suitability for latent heat thermal energy storage (LHTES) assessed. The melt processing temperature (160 °C) of the HDPE used was well below the onset of thermal decomposition of H-PW (220 °C), but above that for L-PW (130 °C), although the decomposition process extended over a range of 120 °C and the residence time of L-PW in the extruder was <30 s. The SSPCMs prepared had latent heats up to 89 J/g and the enthalpy values for H-PW in the respective blends decreased with increasing H-PW loading, as a consequence of co-crystallisation of H-PW and hv-HDPE. Static and dynamic mechanical analysis confirmed both waxes have a plasticisation effect on this HDPE. Irrespective of the mode of deformation (tension, flexural, compression) modulus and stress decreased with increased wax loading in the blend, but the H-PW blends were mechanically superior to those with L-PW.

Length matters:Keeping atomic wires in check

Dynamical effects of non-conservative forces in long, defect free atomic wires are investigated. Current flow through these wires is simulated and we find that during the initial transient, the kinetic energies of the ions are contained in a small number of phonon modes, closely clustered in frequency. These phonon modes correspond to the waterwheel modes determined from preliminary static calculations. The static calculations allow one to predict the appearance of non-conservative effects in advance of the more expensive real-time simulations. The ion kinetic energy redistributes across the band as non-conservative forces reach a steady state with electronic factional forces. The typical ion kinetic energy is found to decrease with system length, increase with atomic mass, and its dependence on bias, mass and length is supported with a pen and paper model. This paper highlights the importance of non-conservative forces in current carrying devices and provides criteria for the design of stable atomic wires.

Património rural construído do Baixo Guadiana

O património rural mediterrânico encerra um quadro de manifestações passadas e presentes com uma riqueza específica e uma diversidade de significados. No quadro de uma ampla parceria dialogante, com uma estrutura técnica entusiasta, dinâmica e crente no desenvolvimento do território do espaço do Mediterrâneo e Baixo Guadiana, foram feitas trocas de experiências, discutidos conceitos e metodologias de intervenção e analisados impactos de onde resultou para cada território um conjunto de acções- piloto de carácter transnacional que consubstanciassem as temáticas do projecto Rural Med, onde se enquadra o presente estudo do Baixo Guadiana.

Klebemöglichkeiten von PTFE

Die hohe Beständigkeit und die antiadhäsiven Eigenschaften von Polytetrafluorethylen (PTFE) erschweren das Kleben dieses Kunststoffes beträchtlich. Da PTFE praktisch unlöslich ist, können Diffusionsklebverbindungen nicht hergestellt werden und Adhäsionsklebverbindungen haben nur eine geringe Festigkeit. Es ist jedoch durch entsprechende Behandlungen möglich, die Oberfläche so zu verändern, dass hochfeste Adhäsionsklebverbindungen möglich sind.

Bedarf im Blick : Betriebliche Voraussetzungen für das Nutzen von Logistiksoftware in der spanenden Fertigung

Wegen der Vielzahl unterschiedlicher Teile in variierenden Losgrößen ist es in der spanenden Fetigung besonders wichtig, Hardware und Software für logistische Aufgaben anforderungsgerecht auszuwählen. Ausgehend von den logistischen Grundfunktionen im Betrieb sind die Grunddatenbereitstellung, die Prozessstruktur, die Produktgestaltung, das Beschaffen und das Lagern auf die rechnergestützte Logistik auszurichten.

Land deed between Alex Outlaw and Calvin Spencer

This document is a land deed between Alex Outlaw and Calvin Spencer.

Indenture deed from Senator Thomas Botewright of Craven County

This document is an indenture deed from Senator Thomas Botewright of Craven County to Calvin Spencer.

Indenture deed between Hayward Todd, Senior and Calvin Spencer

This document is an indenture deed between Hayward Todd, Sr. and Calvin Spencer