Effects of surface treatments on the fatigue strength of AISI 4340 aeronautical steel

Internal residual stresses significantly influence the fatigue strength of coated materials. It is well known that chromium plating is the most used electrodeposited coating for important industrial applications. However, pressure to identify alternatives or to improve the chromium electroplating process have increased in recent years, related to the reduction in fatigue strength of the base material and to environmental requirements. The high efficiency and fluoride free hard chromium electroplating there called accelerated) is an improvement to the conventional process. One environmentally safer and cleaner alternative to hard chromium plating is tungsten carbide thermal spray coating applied by the High Velocity Oxy-Fuel (HVOF) process. To increase the fatigue strength of chromium plated materials, coating thickness and microcracks density are important parameters to be controlled. Techniques as compressive residual stresses induced by shot peening and multilayers, are also used. The aim of this study was to analyse the effects on AISI 4340 steel, in the rotating bending fatigue behaviour, of the: tungsten carbide thermal spray coating applied by HP/HVOF process; chemical nickel underplate, and shot peening process applied before coating deposition, in comparison to hard chromium electroplatings. Rotating bending fatigue test results indicate better performance for the conventional hard chromium plating in relation to the accelerated hard chromium electroplating. Tungsten carbide thermal spray coating and accelerated hard chromium plate over nickel resulted in higher fatigue strength when compared to samples conventional or accelerated hard chromium plated. Shot peening showed to be an excellent alternative to increase fatigue strength of AISI 4340 steel hard chromium electroplated. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Avrami exponent of crystallization in tellurite glasses

Nucleation process and crystal growth for three samples of the (20-x)Li(2)O-80TeO(2)-xWO(3) glass system were studied using X-ray diffraction and differential scanning calorimetry techniques. X-ray diffraction data confirmed the amorphous characteristic of the as-quenched samples and indicated the growth of crystalline phases formed due to the thermal treatment for annealed samples. These results reveal the presence of three distinct gamma-TeO(2), alpha-TeO(2) and alpha-Li(2)Te(2)O(5) crystalline phases in the TL sample, and two distinct alpha-TeO(2) and gamma-TeO(2) crystalline phases in the TLW5 and TLW10 samples. The activation energy and the Avrami exponent were determined from DSC measurements. The activation energy values X-ray diffraction data of the TLW10 glass sample suggest that gamma-TeO(2) phase occur before the alpha-TeO(2). The results obtained for the Avrami exponent point to that the nucleation process is volumetric and that the crystal growth is two or three-dimensional.

Monte Carlo thermodynamic and structural properties of the TIP4P water model: dependence on the computational conditions

Classical Monte Carlo simulations were carried out on the NPT ensemble at 25°C and 1 atm, aiming to investigate the ability of the TIP4P water model [Jorgensen, Chandrasekhar, Madura, Impey and Klein; J. Chem. Phys., 79 (1983) 926] to reproduce the newest structural picture of liquid water. The results were compared with recent neutron diffraction data [Soper; Bruni and Ricci; J. Chem. Phys., 106 (1997) 247]. The influence of the computational conditions on the thermodynamic and structural results obtained with this model was also analyzed. The findings were compared with the original ones from Jorgensen et al [above-cited reference plus Mol. Phys., 56 (1985) 1381]. It is notice that the thermodynamic results are dependent on the boundary conditions used, whereas the usual radial distribution functions g(O/O(r)) and g(O/H(r)) do not depend on them.

Correlação entre os métodos de concepção, ocorrência e formas de tratamento das onfalopatias em bovinos: estudo retrospectivo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Levels of toxic and essential metals in maternal and umbilical cord blood from selected areas of South Africa-results of a pilot study

This pilot study uses concentrations of metals in maternal and cord blood at delivery, in seven selected geographical areas of South Africa, to determine prenatal environmental exposure to toxic metals. Samples of maternal and cord whole blood were analysed for levels of cadmium, mercury, lead, manganese, cobalt, copper, zinc, arsenic and selenium. Levels of some measured metals differed by site, indicating different environmental pollution levels in the regions selected for the study. Mercury levels were elevated in two coastal populations studied (Atlantic and Indian Ocean sites) with mothers from the Atlantic site having the highest median concentration of 1.78 mu g/L ranging from 0.44 to 8.82 mu g/L, which was found to be highly significant (p < 0.001) when compared to other sites, except the Indian Ocean site. The highest concentration of cadmium was measured in maternal blood from the Atlantic site with a median value of 0.25 mu g/L (range 0.05-0.89 mu g/L), and statistical significance of p < 0.032, when compared to all other sites studied, and p < 0.001 and p < 0.004 when compared to rural and industrial sites respectively, confounding factor for elevated cadmium levels was found to be cigarette smoking. Levels of lead were highest in the urban site, with a median value of 32.9 mu g/L (range 16-81.5 mu g/L), and statistically significant when compared with other sites (p < 0.003). Levels of selenium were highest in the Atlantic site reaching statistical significance (p < 0.001). All analysed metals were detected in umbilical cord blood samples and differed between sites, with mercury being highest in the Atlantic site (p < 0.001), lead being highest in the urban site (p < 0.004) and selenium in the Atlantic site (p < 0.001). To the best of our knowledge this pilot investigation is the first study performed in South Africa that measured multiple metals in delivering mothers and umbilical cord blood samples. These results will inform the selection of the geographical sites requiring further investigation in the main study.

Ocorrência de leucose enzoótica bovina na microrregião da Serra de Botucatu

The aim of this study was characterize the positivity of the bovine leukosis virus in the Microregion of the Serra de Botucatu. Sera from 1193 bovine from 65 properties of the Microregion of the Serra de Botucatu were evaluated throught ELISA test. All the evaluated animals were adult and 16 of them only were male; 85.5% were crossbred, 6.45% Nellore and 8% dutch. of the analyzed samples, 618 sera had resulted positive to the test. In only one flock it was not found seroreagents animals, the regional positivity was 52% (the seropositivity in the properties varied of 10% to 67%), the higher the percentage of positivity was in the animals of the dutch race (94.7%), followed for the crossbred (43.7%). The high percentage of positivity of the disease in our region is distinguished.

Desigualdades sociais na prevalência de doenças crônicas no Brasil, PNAD-2003

Os inquéritos de saúde de base populacional constituem o principal instrumento utilizado para conhecer a prevalência de doenças crônicas, de restrições de atividades e de uso de serviços de saúde. Com base nos dados da PNAD-2003, foram estimadas as prevalências das 12 doenças crônicas pesquisadas, segundo sexo, idade, cor, escolaridade, macrorregião de residência e situação urbana ou rural do domicílio. Foram analisados a presença de limitações e o uso de serviços de saúde segundo a presença de doença crônica. Utilizando regressão de Poisson, foram estimadas as razões de prevalências ajustadas por idade, sexo, macrorregião de residência e tipo de respondente. A prevalência de pelo menos uma doença crônica aumentou com a idade, foi maior entre mulheres, indígenas, pessoas com menor escolaridade, cidadãos detentores de plano de saúde, migrantes de outros estados, residentes em áreas urbanas e moradores da região Sul. A presença de doença crônica provocou aumento de limitação de atividades e da demanda por serviços de saúde. As condições mais prevalentes foram: doença de coluna, hipertensão, artrite e depressão. Foi detectada significativa desigualdade social no padrão das doenças crônicas, segundo gênero, cor/raça, nível de escolaridade, região de residência e situação do domicílio.

New Nanostructured Silica Adjuvant (SBA-15) Employed to Produce Antivenom in Young Sheep Using Crotalus durissus terrificus and Apis mellifera Venoms Detoxified by Cobalt-60

Equine antivenom is considered the only treatment for animal-generated envenomations, but it is costly. The study aimed to produce Apis mellifera (Africanized honeybee) and Crotalus durissus terrificus (C.d.t.) antivenoms using nanostructured silica (SBA-15) as adjuvant and cobalt-60 (60Co)-detoxified venoms utilizing young sheep. Natural and 60Co-irradiated venoms were employed in four different hyperimmunization protocols. Thus, 8 groups of 60- to 90-d-old sheep were hyperimmunized, enzyme-linked immunosorbent assay (ELISA) serum titers collected every 14 d were assessed clinically daily, and individual weight were measured, until d 84. Incomplete Freund's (IFA) and nanostructured silica (SBA15) adjuvants were compared. The lethal dose (LD50) for both venoms was determined following intraperitoneal (ip) administration to mice. High-performance liquid chromatography on reversed phase (HPLC-RP) was used also to measure the 60Co irradiation effects on Apis venom. At the end of the study, sheep were killed in a slaughterhouse. Kidneys were histologically analyzed. LD50 was 5.97 mg/kg Apis and 0.07 mg/kg C.d.t. for native compared to 13.44 mg/kg Apis and 0.35 mg/kg C.d.t. for irradiated venoms. HPLC revealed significant differences in chromatographic profiles between native and irradiated Apis venoms. Native venom plus IFA compared with SBA-15 showed significantly higher antibody titers for both venoms. Apis-irradiated venom plus IFA or SBA-15 displayed similar antibody titers but were significantly lower when compared with native venom plus IFA. Weight gain did not differ significantly among all groups. 60Co irradiation decreased toxicity and maintained venom immunogenic capacity, while IFA produced higher antibody titers. SBA-15 was able to act as an adjuvant without producing adverse effects. Hyperimmunization did not affect sheep weight gain, which would considerably reduce the cost of antiserum production, as these sheep were still approved for human consumption even after being subjected to hyperimmunization.

Gonadic Sperm Reserve in Buffaloes Created under Tropical Conditions

The objective of the present study was quantifying the spermatic production per gram and daily rate of the testicular parenchyma. Testis of 12 crossbred Murrah buffaloes aged 24 to 48 months created under extensive conditions in the State of São Paulo/Brazil were analyzed. Animals were divided into groups based on the testicular shape (long and long-moderate) and testicular sides (right and left) and the studied parameters were: length and testicular width, weight and volume of the albuginea and mediastinum and net weight of the testicular parenchyma, gonadic sperm reserves, spermatic production/g of testicular parenchyma, daily spermatic production/g, total daily spermatic production, resulting into the values: 8.16 +/- 0.87 and 4.29 +/- 0.50 cm; 9.09 +/- 1.91 g and 8.77 +/- 1.88 mL; 0.97 +/- 0.39 g and 0.90 +/- 0.38 mL; 112.91 +/- 18.85 g; 14.32 x 10(9) +/- 0.15; 13.42 x 10(6) +/- 0.17; 27.40 x 10(6) +/- 0.35 and 2.92 x 10(9) +/- 0.30, registering no difference between right and left testis in relation to the parameters (P>0.05). There was no relation between testicular biometry and spermatic production (P>0.05). According to the obtained values, all animals were considered sexually mature and presented an efficient spermatic production per gram of testicular parenchyma and total daily production.

A comparison of profilometer and AutoCAD software techniques in evaluation of implant angulation in vitro

Purpose: The aim of this study was to compare 2 different methods of assessment of implants at different inclinations (90 degrees and 65 degrees)-with a profilometer and AutoCAD software. Materials and Methods: Impressions (n = 5) of a metal matrix containing 2 implants, 1 at 90 degrees to the surface and 1 at 65 degrees to the surface, were obtained with square impression copings joined together with dental floss splinting covered with autopolymerizing acrylic resin, an open custom tray, and vinyl polysiloxane impression material. Measurement of the angles (in degrees) of the implant analogs were assessed by the same blinded operator with a profilometer and through analysis of digitized images by AutoCAD software. For each implant analog, 3 readings were performed with each method. The results were subjected to a nonparametric Kruskal-Wallis test, with P <= .05 considered significant. Results: For implants perpendicular to the horizontal surface of the specimen (90 degrees), there were no significant differences between the mean measurements obtained with the profilometer (90.04 degrees) and AutoCAD (89.95 degrees; P=.9142). In the analyses of the angled implants at 65 degrees in relation to the horizontal surface of the specimen, significant differences were observed (P=.0472) between the mean readings with the profilometer (65.73 degrees) and AutoCAD (66.25 degrees). Conclusions: The degrees of accuracy of implant angulation recording vary among the techniques available and may vary depending on the angle of the implant. Further investigation is needed to determine the best test conditions and the best measuring technique for determination of the angle of the implant in vitro.

The Role of Lipopolysaccharide on the Electrochemical Behavior of Titanium

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Expression of the Interleukin-10 Signaling Pathway Genes in Individuals With Down Syndrome and Periodontitis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Damage of the medial preoptic area impairs peripheral pilocarpine-induced salivary secretion

The existence of neural connections between the medial preoptic area (MPOA) and the salivary glands and the increase in salivation by thermal or electrical stimulation of the MPOA have suggested an important role of MPOA in the control of salivary gland function. Although direct cholinergic activation of the salivary glands induces salivation, recent studies have suggested that salivation produced by i.p. pilocarpine may also depend on the activation of central mechanisms. Therefore, in the present study, we investigated the effects of bilateral electrolytic lesions of the MPOA on the salivation induced by i.p. pilocarpine. Adult male Holtzman rats (n = 11-12/group) with bilateral sham or electrolytic lesions of the MPOA were used. One, five, and fifteen days after the brain surgery, under ketamine anesthesia, the salivation was induced by i.p. pilocarpine (1 mg/kg of body weight), and saliva was collected using preweighted small cotton balls inserted into the animal's mouth. Pilocarpine-induced salivation was reduced 1 and 5 days after MPOA lesion (341 +/- 41 and 310 +/- 35 mg/7 min, respectively, vs. sham lesions 428 +/- 32 and 495 +/- 36 mg/7 min, respectively), but it was fully recovered at the 15th day post-lesion (561 +/- 49 vs. sham lesion: 618 27 mg/7 min). Lesions of the MPOA did not affect baseline non-stimulated salivary secretion. The results confirm the importance of MPOA in the control of salivation and suggest that its integrity is necessary for the full sialogogue effect of pilocarpine. However, alternative mechanisms probably involving other central nuclei can replace MPOA function in chronically lesioned rats allowing the complete recovery of the effects of pilocarpine. (c) 2006 Published by Elsevier B.V.

Effect of dentin conditioning time on nanoleakage

Objectives: To study the nanoleakage pattern in the dentin hybrid layer by using different dentin adhesives. The null hypotheses tested in this study were: 1) dentin conditioning time does not affect nanoleakage within the hybrid layer; 2) the type of dentin adhesive used does not affect nanoleakage. Methods: Standardized Class V cavities were prepared in 30 intact human molars on the buccal and lingual surfaces. The specimens were randomly assigned to 2 total-etch dentin adhesives (OptiBond SOLO Plus [OPS, Kerr] and One-Step [ONS, BISCO Inc]) and 2 self-etch dentin adhesives (Clearfil SE Bond [CSE, Kuraray] and Adper Prompt L-Pop [APL, 3M ESPE]). The specimens were etched or conditioned for 15 seconds, 30 seconds or 60 seconds. Upon restoration of the Class V cavities with the proprietary resin composite, the specimens were isolated with nail polish except for a 2.0-mm rim around the restoration, and they were immersed in 50 wt% ammoniacal silver nitrate solution (pH=9.5) for 24 hours followed by 8 hours of immersion in photo-developing solution to reduce the silver ions to metallic silver. The specimens were fixed, dehydrated and processed for FESEM and TEM. Silver penetration was measured along the cervical wall, and data were analyzed with Kruskal-Wallis non-parametric tests at a significance level of 95%. Results: There were no statistically significant differences among the experimental groups for the factor conditioning time (p>0.926). There were significant differences for the variable dentin adhesive (p<0.0001). The least amount of nanoleakage within the hybrid layer occurred with CSE, while ONS resulted in the greatest penetration of silver ions. The adhesives OPS and APL ranked in the intermediary subset. Under TEM, all adhesives resulted in some degree of nanoleakage within the hybrid layer. Both spotted/reticular and water-tree nanoleakage patterns were observed. Significance: Longer conditioning times did not increase nanoleakage within the hybrid layer. Nanoleakage varied with the type of adhesive used.

Neuroendocrine and reproductive aspects of adult male rats exposed neonatally to an antiestrogen

The present study was designed to investigate the effects of a single dose of an estrogen antagonist-clomiphene-during neonatal life, on later neuroendocrine system and reproductive performance. Immediately after birth, male pups received clomiphene citrate (s.c.). At adulthood, although testosterone levels and wet weights of reproductive organs were not altered, the treatment induced an increased number of spermatozoa and a delay in the transit time in the cauda epididymis. Additionally, there was impairment of sexual behavior evidenced by a delay in the latencies to the first mount and first intromission. Treated rats also showed decreased dopaminergic and serotonergic neurotransmissions in the hypothalamus and decreased dopaminergic neurotransmission in the striatum. The decreased dopaminergic activity could be related to the lower sexual motivation observed. These results indicate the necessity of preventing exposure to drugs that may impair sexual differentiation, which can compromise later mating success as well as the capacity to generate descendants. (c) 2006 Elsevier B.V. All rights reserved.