Refining of Low Grade Zinc-Gold Precipitates

The purpose of this investigation was to ascertain if advantage could be taken of the copper in the precipitates as a collecting agent of the precious metals in the direct smelting furnace.The products produced to be low grade anode bullion and a slag low in precious metals, high in zinc and lead.

Great Falls Tectonic Zone: A Perspective from Idaho

An overview of geologic constraints on the age and extent of the Great Falls tectonic zone, a northeast-trending set of faults identified in west-central Montana.

The Effects of Some Percentages of Nickel on the Annealing of Cartridge Brass

The most important element in the alloying of steels, has also been used quite extensively as a third constituent in copper-zinc alloys. The chief characteristics of nickel which make it desirable as an alloying element are its toughness, high strength, and resistance to corrosion.

Zinc Plating Magnesium

Magnesium and magnesium alloys are becoming more and more important in modern industry. Their use in the aviation industry has been greatly curtailed because of their comparatively poor resistance to corrosion especially in moist atmospheres. Many methods have been adopted to improve their resistance to corrosion.

Coal in Montana

Coal was first mined in Montana in the year 1880. For the last thirty years the mining of coal in this state has been very important-with few people realizing its value. In the mineral industry, the value of the annual production of coal is exceeded by none of the non-metallics, and only by gold, silver, and copper in the metallics. At the present time the coal production of Montana is valued at about 41000,000.00 annually.

Permeability and Porosity Studies of the Cut Bank Oil Sand

In studying the Cut Bank field and its numerous wells, it is found that dry holes are surrounded by producing wells, and also that the field as a whole is very irregular; water, oil, and gas zones in many cases following no definite pattern. In some instances, this phenomenon may be due to the lensing and thinning of the producing sands, but it is evident that this is not the only factor. There­fore, the controlling factors must be porosity and permeability.

Spectrographic Analysis of Montana Limestones

Spectrographic analysis of limestones as a possible method of correlation of geologic formations is an altogether new line of investigation. As far as known the only previous work consists of a few analyses made by Fred Lines in his bachelor thesis work at Montana School of mines in the spring of 1942.

Concentration by Flotation of a Complex Galena - Sphalerite - Chalcopyrite Ore from the Nine Mile District Near Missoula, Montana

At the present time ore bodies being mined are becoming more and more complex in mineral association, thus presenting a more difficult problem in their concentration. Lead-zinc sulphide ores are among the more common ores which present such difficulties.

The Effect of Boron on the Hardenability of Steel

Many attempts have been made to improve iron and steel and their alloys by the addition of boron. The re­sults obtained were not encouraging for the reason that the amount of boron used, generally from 0.2 to 2.0 per cent is altogether too high. This percentage of boron ren­ders the product hard and brittle and of late the experiments with boron in this connection have been practically abandoned.

An Attempt to Increase the Permeability and Porosity of the Cut Bank Oil Sand By Treatment with Various Reagents

The purpose of this investigation was to attempt to find some means of increasing the effective porosity and permeabil­ity of the producing sands of the Cut Bank Oil Field, with the hope that thereby the ultimate recovery of petroleum from this field may be increased. Although the percentage increase in production thus effected would undoubtedly be small, it would represent a substantial volume of petroleum in view of the great quantity of oil and gas present in this field.

The Electrodeposition of Chromium from Trivalent Salt Solutions

The enormous number of previous experiments and researches for the improvement of the commercial chromic acid bath, did not succeed even in the partial elimination of any one of the disadvantages of chromic acid bath. This led the author to believe that the poor performance is an inherent quality of the chromic acid bath, and is due to the fact that the deposition occurs from the higher state of oxidation.

Bright Electroplating of Copper in the Acid Bath

Plating of various objects with mirror-like surfaces of chromium, nickel, and other metals has expanded considerably during the past decade, and now ranks as an important enterprise, particularly with respect to the automotive industry.

The Electrodeposition of Iron-Manganese Alloys

Various electrolytes were experimented with in an attempt to deposit an iron-manganese alloy. An Alloy was obtained from a solution containing ferrous ammonium sulfate, manganous sulfate, and ammonium sulfate. Further experimentation was done in an effort to determine the optimum conditions of deposition and the highest manganese alloy which could be produced.

Flotation of a Complex Sulphide Ore Containing Tetrahedrite

The ore investigated in this thesis is a zinc-copper-lead ore. Microscopic analysis of this complex sulphide ore showed it to contain pyrite, sphalerite, arsenopyrite, galena, chalcopyrite, tetrahedrite, and covellite, with quartz as the gangue constituent.

Electrolytic Manganese from Aqueous Sodium Manganate Solution

The contents of this paper represent attempts to deposit the metal, manganese from sodium manganate solutions. The source of manganese was limited to the nodulized product from roasting rhodochrosite and was therefore chiefly manganese oxide.