Use of homeo drug for curing ulcerative syndrome in fishes

Fungal infection was observed in Catla catla and Labeo rohita cultured in two private fish farms. The later stage of the infection resulted in ulcerations followed by haemorrhage on the dorsal surface of the body. Initially, usual treatments of copper sulphate, potassium permanganate and common salt solution were tried, but no improvement was observed. Then repeated intramuscular injections of homeopathic drug Heaper Sulpher and Arnica spray were given with encouraging results. Infection reported in another farm was also successfully controlled using a similar treatment.

Influence of particle properties on the erosive wear of sintered boron carbide

Sintered boron carbide is very hard, and can be an attractive material for wear-resistant components in critical applications. Previous studies of the erosion of less hard ceramics have shown that their wear resistance depends on the nature of the abrasive particles. Erosion tests were performed on a sintered boron carbide ceramic with silica, alumina and silicon carbide erodents. The different erodents caused different mechanisms of erosion, either by lateral cracking or small-scale chipping; the relative values of the hardness of the erodent and the target governed the operative mechanism. The small-scale chipping mechanism led to erosion rates typically an order of magnitude lower than the lateral fracture mechanism. The velocity exponents for erosion in the systems tested were similar to those seen in other work, except that measured with the 125 to 150 μm silica erodent. With this erodent the exponent was initially high, then decreased sharply with increasing velocity and became negative. It was proposed that this was due to deformation and fragmentation of the erodent particles. In the erosion testing of ceramics, the operative erosion mechanism is important. Care must be taken to ensure that the same mechanism is observed in laboratory testing as that which would be seen under service conditions, where the most common erodent is silica.

Comparison of different scheduling techniques for H-infinity controllers

Several approaches to designing schedule H-infinity control systems are compared. These include a controller switching approach and also parameter scheduling of an observer representation of the controller. They are illustrated by application to a Generic VSTOI. Aircraft Model (GVAM) supplied by The Royal Aerospace Establishment (RAE) at Bedford. The switched design has been tested on the simulator at RAE Bedford. The linear H-infinity designs make use of a loop-shaping followed by robust stabilisation to additive perturbations of a normalised coprime factorisation of the shaped plans. The different scheduling approaches are compared with respect to achieved robust stability levels. performance and complexity of implementation.

Applications of stochastic context-free grammars using the Inside-Outside algorithm

This paper describes two applications in speech recognition of the use of stochastic context-free grammars (SCFGs) trained automatically via the Inside-Outside Algorithm. First, SCFGs are used to model VQ encoded speech for isolated word recognition and are compared directly to HMMs used for the same task. It is shown that SCFGs can model this low-level VQ data accurately and that a regular grammar based pre-training algorithm is effective both for reducing training time and obtaining robust solutions. Second, an SCFG is inferred from a transcription of the speech used to train a phoneme-based recognizer in an attempt to model phonotactic constraints. When used as a language model, this SCFG gives improved performance over a comparable regular grammar or bigram. © 1991.

Investigation of extinction in unsteady flames in turbulent combustion by 2D-LIF of OH radials and flamelet analysis

An experimental and theoretical investigation of premixed turbulent combustion in an engine simulator is presented. The distribution of hydroxyl radicals formed in the combustion of propane/air mixtures was visualized by 2D-LIF and used to monitor the progress of the combustion process. For stoichiometric mixtures, images showed a continuous wrinkled flame front, while in lean (λ=1.5) mixtures, local flame extinction was observed as discontinuities in the reaction zone. A bright active reaction zone was still observed in flame inlets and closed concave structures. The effects of self-absorption and of collisional quenching on the fluorescence signal are considered and appear to have only a minor net influence on the shape and width of the flame front. The images are evaluated and interpreted in terms of the Lewis number effect and the laminar flamelet model. Analysis was performed by determining the contour lines of the images (specifically, the ratios of average maximum to equilibrium OH concentration) and comparing with corresponding ratios from unstrained flame simulations. The results show that although the degree of turbulence is not high enough for straining effects to be important, flamelet curvature does play a significant role in the combustion of lean mixtures; this is manifested by a mean effective flame velocity that is less than the laminar burning velocity. © 1991 Combustion Institute.

Properties of tetrahedral amorphous carbon prepared by vacuum arc deposition

The structural, optical, electrical and physical properties of amorphous carbon deposited from the filtered plasma stream of a vacuum arc were investigated. The structure was determined by electron diffraction, neutron diffraction and energy loss spectroscopy and the tetrahedral coordination of the material was confirmed. The measurements gave a nearest neighbour distance of 1.53 Å, a bond angle of 110 and a coordination number of four. A model is proposed in which the compressive stress generated in the film by energetic ion impact produces pressure and temperature conditions lying well inside the region of the carbon phase diagram within which diamond is stable. The model is confirmed by measurements of stress and plasmon energy as a function of ion energy. The model also predicts the formation of sp2-rich materials on the surface owing to stress relaxation and this is confirmed by a study of the surface plasmon energy. Some nuclear magnetic resonance, infrared and optical properties are reported and the behaviour of diodes using tetrahedral amorphous carbon is discussed. © 1991.