Modelling busway station dwell time using smart cards

Dwell time at the busway station has a significant effect on bus capacity and delay. Dwell time has conventionally been estimated using models developed on the basis of field survey data. However field survey is resource and cost intensive, so dwell time estimation based on limited observations can be somewhat inaccurate. Most public transport systems are now equipped with Automatic Passenger Count (APC) and/or Automatic Fare Collection (AFC) systems. AFC in particular reduces on-board ticketing time, driver’s work load and ultimately reduces bus dwell time. AFC systems can record all passenger transactions providing transit agencies with access to vast quantities of data. AFC data provides transaction timestamps, however this information differs from dwell time because passengers may tag on or tag off at times other than when doors open and close. This research effort contended that models could be developed to reliably estimate dwell time distributions when measured distributions of transaction times are known. Development of the models required calibration and validation using field survey data of actual dwell times, and an appreciation of another component of transaction time being bus time in queue. This research develops models for a peak period and off peak period at a busway station on the South East Busway (SEB) in Brisbane, Australia.

A microscopic simulation model to estimate bus rapid transit station bus capacity

The Bus Rapid Transit (BRT) station is the interface between passengers and services. The station is crucial to line operation as it is typically the only location where buses can pass each other. Congestion may occur here when buses maneuvering into and out of the platform lane interfere with bus flow, or when a queue of buses forms upstream of the platform lane blocking the passing lane. Further, some systems include operation where express buses do not observe the station, resulting in a proportion of non-stopping buses. It is important to understand the operation of the station under this type of operation and its effect on BRT line capacity. This study uses microscopic traffic simulation modeling to treat the BRT station operation and to analyze the relationship between station bus capacity and BRT line bus capacity. First, the simulation model is developed for the limit state scenario and then a statistical model is defined and calibrated for a specified range of controlled scenarios of dwell time characteristics. A field survey was conducted to verify the parameters such as dwell time, clearance time and coefficient of variation of dwell time to obtain relevant station bus capacity. The proposed model for BRT bus capacity provides a better understanding of BRT line capacity and is useful to transit authorities in BRT planning, design and operation.

‘All in a day’s work’ : the lifeworld of older people in New Zealand rest homes

This doctoral thesis contributes to critical gerontology research by investigating the lived experiences of residents in the everyday world of New Zealand rest homes. There is a need to understand how frail rest home residents experience "age". This study focuses on describing and understanding residents lived experiences. As the New Zealand population is ageing, this phenomenological focus adds clarity to the poorly understood lived experiences about being aged in rest homes. Policy initiatives such as the Positive Ageing Strategy with its emphasis on keeping older people living in the community largely ignore the life practices of the increasing proportions of frail older people who require long-term residential care. My mixed-methods modified framework approach draws on the lifeworld as understood by Max van Manen (1990) and Alfred Schütz (1972). The lifeworld is made up of thematic strands of lived experience: these being lived space, lived time, lived body and lived relations with others, which are both the source and object of phenomenological research (van Manen, 1990). These strands are temporarily unravelled and considered in-depth for 27 residents who took part in audio-recorded interviews, before being interwoven through a multiple-helix model, into an integrated interpretation of the residents‟ lifeworld. Supplementing and backgrounding the interviews with these residents, are descriptive data including written interview summaries and survey findings about the relationships and pastimes of 352 residents living in 21 rest homes, which are counted and described. The residents day-to-day use of rest home space, mediated temporal order, self-managed bodies and minds, and negotiated relationships are interpreted. The mythology of the misery of rest home life is challenged, and a more constructive critical gerontology approach is offered. Findings of this research reveal how meanings around daily work practices are constructed by the residents. These elders participate in daily rest home life, from the sidelines or not at all, as they choose or are able, and this always involves work for the residents. They continue to actively manage satisfactory and fulfilling pastimes and relationships, because in their ordinary, everyday lifeworld it is “all in a day‟s work”.

High-risk, high-stake relationships: building effective industry-university partnerships for Work Integrated Learning (WIL)

Many industry peak and professional bodies advocate students undertake professional work placements as a key work integrated learning (WIL) experience in accredited university degree courses. However, mismatched expectations and gaps in the way industry partners (IPs) are supported during these work placements can place these high-stake alliances at risk. A review of models and strategies supporting industry partners indicates many are contingent on the continued efforts of well-networked individuals in both universities and IP organisations to make these connections work. It is argued that whilst these individuals are highly valued they often end up representing a whole course or industry perspective, not just their area of expertise. Sustainable partnership principles and practices with shared responsibility across stakeholder groups are needed instead. This paper provides an overview of work placement approaches in the disciplines of business, engineering and urban development at an Australian, metropolitan university. Employing action research and participatory focus group methodologies, it gathers and articulates recommendations from associated IPs on practical suggestions and strategies to improve relationships and the resultant quality of placements.

Role of particle size and composition in metal adsorption by solids deposited on urban road surfaces

Despite common knowledge that the metal content adsorbed by fine particles is relatively higher compared to coarser particles, the reasons for this phenomenon has gained little research attention. The research study discussed in the paper investigated the variations in metal content for different particle sizes of solids associated with pollutant build-up on urban road surfaces. Data analysis confirmed that parameters favourable for metal adsorption to solids such as specific surface area, organic carbon content, effective cation exchange capacity and clay forming minerals content decrease with the increase in particle size. Furthermore, the mineralogical composition of solids was found to be the governing factor influencing the specific surface area and effective cation exchange capacity. There is high quartz content in particles >150µm compared to particles <150µm. As particle size reduces below 150µm, the clay forming minerals content increases, providing favourable physical and chemical properties that influence adsorption.

Measurement, modelling and capacity analysis for novel, fixed multi-user single-antenna MIMO-OFDM system, in rural environments

High-speed broadband internet access is widely recognised as a catalyst to social and economic development. However, the provision of broadband Internet services with the existing solutions to rural population, scattered over an extensive geographical area, remains both an economic and technical challenge. As a feasible solution, the Commonwealth Scientific and Industrial Research Organization (CSIRO) proposed a highly spectrally efficient, innovative and cost-effective fixed wireless broadband access technology, which uses analogue TV frequency spectrum and Multi-User MIMO (MUMIMO) technology with Orthogonal-Frequency-Division-Multiplexing (OFDM). MIMO systems have emerged as a promising solution for the increasing demand of higher data rates, better quality of service, and higher network capacity. However, the performance of MIMO systems can be significantly affected by different types of propagation environments e.g., indoor, outdoor urban, or outdoor rural and operating frequencies. For instance, large spectral efficiencies associated with MIMO systems, which assume a rich scattering environment in urban environments, may not be valid for all propagation environments, such as outdoor rural environments, due to the presence of less scatterer densities. Since this is the first time a MU-MIMO-OFDM fixed broadband wireless access solution is deployed in a rural environment, questions from both theoretical and practical standpoints arise; For example, what capacity gains are available for the proposed solution under realistic rural propagation conditions?. Currently, no comprehensive channel measurement and capacity analysis results are available for MU-MIMO-OFDM fixed broadband wireless access systems which employ large scale multiple antennas at the Access Point (AP) and analogue TV frequency spectrum in rural environments. Moreover, according to the literature, no deterministic MU-MIMO channel models exist that define rural wireless channels by accounting for terrain effects. This thesis fills the aforementioned knowledge gaps with channel measurements, channel modeling and comprehensive capacity analysis for MU-MIMO-OFDM fixed wireless broadband access systems in rural environments. For the first time, channel measurements were conducted in a rural farmland near Smithton, Tasmania using CSIRO's broadband wireless access solution. A novel deterministic MU-MIMO-OFDM channel model, which can be used for accurate performance prediction of rural MUMIMO channels with dominant Line-of-Sight (LoS) paths, was developed under this research. Results show that the proposed solution can achieve 43.7 bits/s/Hz at a Signal-to- Noise Ratio (SNR) of 20 dB in rural environments. Based on channel measurement results, this thesis verifies that the deterministic channel model accurately predicts channel capacity in rural environments with a Root Mean Square (RMS) error of 0.18 bits/s/Hz. Moreover, this study presents a comprehensive capacity analysis of rural MU-MIMOOFDM channels using experimental, simulated and theoretical models. Based on the validated deterministic model, further investigations on channel capacity and the eects of capacity variation, with different user distribution angles (θ) around the AP, were analysed. For instance, when SNR = 20dB, the capacity increases from 15.5 bits/s/Hz to 43.7 bits/s/Hz as θ increases from 10° to 360°. Strategies to mitigate these capacity degradation effects are also presented by employing a suitable user grouping method. Outcomes of this thesis have already been used by CSIRO scientists to determine optimum user distribution angles around the AP, and are of great significance for researchers and MU-MUMO-OFDM system developers to understand the advantages and potential capacity gains of MU-MIMO systems in rural environments. Also, results of this study are useful to further improve the performance of MU-MIMO-OFDM systems in rural environments. Ultimately, this knowledge contribution will be useful in delivering efficient, cost-effective high-speed wireless broadband systems that are tailor-made for rural environments, thus, improving the quality of life and economic prosperity of rural populations.

Optical and biomechanical factors, associated with near work and myopia

Near work may play an important role in the development of myopia in the younger population. The prevalence of myopia has also been found to be higher in occupations that involve substantial near work tasks, for example in microscopists and textile workers. When nearwork is performed, it typically involves accommodation, convergence and downward gaze. A number of previous studies have examined the effects of accommodation and convergence on changes in the optics and biometrics of the eye in primary gaze. However, little is known about the influence of accommodation on the eye in downward gaze. This thesis is primarily concerned with investigating the changes in the eye during near work in downward gaze under natural viewing conditions. To measure wavefront aberrations in downward gaze under natural viewing conditions, we modified a commercial Shack-Hartmann wavefront sensor by adding a relay lens system to allow on-axis ocular aberration measurements in primary gaze and downward gaze, with binocular fixation. Measurements with the modified wavefront sensor in primary and downward gaze were validated against a conventional aberrometer using both a model eye and in 9 human subjects. We then conducted an experiment to investigate changes in ocular aberrations associated with accommodation in downward gaze over 10 mins in groups of both myopes (n = 14) and emmetropes (n =12) using the modified Shack-Hartmann wavefront sensor. During the distance accommodation task, small but significant changes in refractive power (myopic shift) and higher order aberrations were observed in downward gaze compared to primary gaze. Accommodation caused greater changes in higher order aberrations (in particular coma and spherical aberration) in downward gaze than primary gaze, and there was evidence that the changes in certain aberrations with accommodation over time were different in downward gaze compared to primary gaze. There were no obvious systematic differences in higher order aberrations between refractive error groups during accommodation or downward gaze for fixed pupils. However, myopes exhibited a significantly greater change in higher order aberrations (in particular spherical aberration) than emmetropes for natural pupils after 10 mins of a near task (5 D accommodation) in downward gaze. These findings indicated that ocular aberrations change from primary to downward gaze, particularly with accommodation. To understand the mechanism underlying these changes in greater detail, we then extended this work to examine the characteristics of the corneal optics, internal optics, anterior biometrics and axial length of the eye during a near task, in downward gaze, over 10 mins. Twenty young adult subjects (10 emmetropes and 10 myopes) participated in this study. To measure corneal topography and ocular biometrics in downward gaze, a rotating Scheimpflug camera and an optical biometer were inclined on a custom built, height and tilt adjustable table. We found that both corneal optics and internal optics change with downward gaze, resulting in a myopic shift (~0.10 D) in the spherical power of the eye. The changes in corneal optics appear to be due to eyelid pressure on the anterior surface of the cornea, whereas the changes in the internal optics (an increase in axial length and a decrease in anterior chamber depth) may be associated with movement of the crystalline lens, under the action of gravity, and the influence of altered biomechanical forces from the extraocular muscles on the globe with downward gaze. Changes in axial length with accommodation were significantly greater in downward gaze than primary gaze (p < 0.05), indicating an increased effect of the mechanical forces from the ciliary muscle and extraocular muscles. A subsequent study was conducted to investigate the changes in anterior biometrics, axial length and choroidal thickness in nine cardinal gaze directions under the actions of the extraocular muscles. Ocular biometry measurements were obtained from 30 young adults (10 emmetropes, 10 low myopes and 10 moderate myopes) through a rotating prism with 15° deviation, along the foveal axis, using a non-contact optical biometer in each of nine different cardinal directions of gaze, over 5 mins. There was a significant influence of gaze angle and time on axial length (both p < 0.001), with the greatest axial elongation (+18 ± 8 μm) occurring with infero-nasal gaze (p < 0.001) and a slight decrease in axial length in superior gaze (−12 ± 17 μm) compared with primary gaze (p < 0.001). There was a significant correlation between refractive error (spherical equivalent refraction) and the mean change in axial length in the infero-nasal gaze direction (Pearson's R2 = 0.71, p < 0.001). To further investigate the relative effect of gravity and extraocular muscle force on the axial length, we measured axial length in 15° and 25° downward gaze with the biometer inclined on a tilting table that allowed gaze shifts to occur with either full head turn but no eye turn (reflects the effect of gravity), or full eye turn with no head turn (reflects the effect of extraocular muscle forces). We observed a significant axial elongation in 15° and 25° downward gaze in the full eye turn condition. However, axial length did not change significantly in downward gaze over 5 mins (p > 0.05) in the full head turn condition. The elongation of the axial length in downward gaze appears to be due to the influence of the extraocular muscles, since the effect was not present when head turn was used instead of eye turn. The findings of these experiments collectively show the dynamic characteristics of the optics and biometrics of the eye in downward gaze during a near task, over time. These were small but significant differences between myopic and emmetropic eyes in both the optical and biomechanical changes associated with shifts of gaze direction. These differences between myopes and emmetropes could arise as a consequence of excessive eye growth associated with myopia. However the potentially additive effects of repeated or long lasting near work activities employing infero-nasal gaze could also act to promote elongation of the eye due to optical and/or biomechanical stimuli.

The ACEN Student Scholarship: a profile of financial hardship and Work Integrated Learning

An increasing emphasis on embedding Work-Integrated Learning (WIL) in the curriculum has impacted on teaching and learning approaches in Australian higher education institutions (Higher Education Base Funding Review: Final Report, 2011). Yet whilst the benefits and costs of these approaches have been identified (Bradley, Noonan, Nugent, & Scales, 2008; Patrick et al., 2009) insufficient attention has been paid to financial costs experienced by students studying subjects with a Work Integrated Learning component. In 2010 the Australian Collaborative Education Network (ACEN) responded to this issue by offering three modest student scholarships based on evidence of hardship. Data collected from over 1000 applicants between 2010 and 2012 indicate travel, accommodation, food, clothing, equipment and loss of income are of major concern especially for students on lengthy placements involving relocation. At the same time the Australian Federal Government’s review of base funding has recommended a detailed assessment of the costs of providing student placements across all disciplines - in particular health and education (DEEWR, 2011, p.94). This paper considers costs from the student perspective and highlights major concerns identified through ACEN scholarship applications over a three year period. The implications for ACEN are described and recommendations documented which outline ACEN’s role in ensuring that these issues are given greater consideration across the sector.

Reconstructing places and spaces in blended work integrated learning

This paper considers the emergence and ongoing development of an embedded, studentnegotiated work placement model of Work Integrated Learning (WIL) in the engineering and built environment disciplines at an Australian metropolitan university. The characteristics of the model and a continuous improvement strategy are provided. The model is characterised by large student cohorts independently sourcing and negotiating relevant work placements and completing at least one, mandatory credit-bearing WIL unit. Through ongoing analyses and evaluation of the model more experiential and collaborative learning approaches have been adopted. This has included the creation of blended learning spaces using technology. The paper focuses on the five year journey travelled by the teaching team as they embarked on ways to improve curriculum, pedagogy, administrative processes and assessment - effectively relocating much of their interaction with students online. The insights derived from this rich, single case study should be of interest to others considering alternative ways of responding to increasing student enrolments in WIL and the impact of blended learning in this context.

Professional development and technology in second language learning : do best practices work?

This study was undertaken to examine the influence that a set of Professional Development (PD) initiatives had on faculty use of Moodle, a well known Course Management System. The context of the study was a private language university just outside Tokyo, Japan. Specifically, it aimed to identify the way in which the PD initiatives adhered to professional development best practice criteria; how faculty members perceived the PD initiatives; what impact the PD initiatives had on faculty use of Moodle; and other variables that may have influenced faculty in their use of Moodle. The study utilised a mixed methods approach. Participants in the study were 42 teachers who worked at the university in the academic year 2008/9. The online survey consisted of 115 items, factored into 10 constructs. Data was collected through an online survey, semi-structured face-to-face interviews, post-workshop surveys, and a collection of textual artefacts. The quantitative data were analysed in SPSS, using descriptive statistics, Spearman's Rank Order correlation tests and a Kruskal-Wallis means test. The qualitative data was used to develop and expand findings and ideas. The results indicated that the PD initiatives adhered closely to criteria posited in technology-related professional development best practice criteria. Further, results from the online survey, post workshop surveys, and follow up face-to-face interviews indicated that while the PD initiatives that were implemented were positively perceived by faculty, they did not have the anticipated impact on Moodle use among faculty. Further results indicated that other variables, such as perceptions of Moodle, and institutional issues, had a considerable influence on Moodle use. The findings of the study further strengthened the idea that the five variables Everett Rogers lists in his Diffusion of Innovations model, including perceived attributes of an innovation; type of innovation decision; communication channels; nature of the social system; extent of change agents' promotion efforts, most influence the adoption of an innovation. However, the results also indicated that some of the variables in Rogers' DOI seem to have more of an influence than others, particularly the perceived attributes of an innovation variable. In addition, the findings of the study could serve to inform universities that have Course Management Systems (CMS), such as Moodle, about how to utilise them most efficiently and effectively. The findings could also help to inform universities about how to help faculty members acquire the skills necessary to incorporate CMSs into curricula and teaching practice. A limitation of this study was the use of a non-randomised sample, which could appear to have limited the generalisations of the findings to this particular Japanese context.

Control, shift, insert : living and enacting policy in teachers' day/night work

This thesis investigates the experiences of teachers who trialled an electronic curriculum and assessment tool in the wider context of text-mediated ruling relations organising their work. Problematised as policy and text, this tool is interrogated as a 'solution' to problems perceived in teachers' work in an era of increased accountability. It provides evidence that teachers' work is shaped by forces operating outside their control and mediated by the policy discourses and subjectivities available to them.

An Australian study on partnerships to promote school to work transitions

The delivery of vocational education and training (VET) is being challenged by either increasing skills shortages and/or rapidly changing skill requirements. To respond to this challenge, centralised state bureaucracies are increasingly adopting partnerships between schools and industry as a strategy to encourage school to work transition programs to address the local labour market demand. This paper reports on an Australian case study of government-led partnerships named the Queensland Gateway to industry schools initiative. 12 out of 120 school industry partnerships from five industry sectors were analysed in terms of the two commonly identified principles derived from the public-private partnership literature; efficiency and effectiveness. The study found that efficiency and effectiveness benefits of partnership activities were attributed to Gateway schools projects by both school and industry stakeholders. However, little evidence was found that the above underlying principles were addressed systematically. Implications are that project stakeholders would benefit from adapting theoretical perspectives regarding the implementation and management of partnerships to ensure the sustainability of partnerships.

School industry partnerships : An innovative strategy for vocational education

One of the challenges confronting contemporary education internationally is to ensure that students are provided with opportunities to make informed choices about future careers and to acquire the capacity to transition into these careers. Schools need to manage their curricula, teacher capacity, timetables, and diversity of student populations by offering pathways that are seen as engaging and meaningful to life beyond schooling. Traditionally, education in the senior years has privileged those students who intend to progress to advanced studies at university or in other professional careers. In more recent times, in response the need for more sophisticated technical knowledge in the trades and a growing skills shortages in these fields, schools have paid more attention to vocational education. It has been argued that the vocational aspect of the school curriculum is less well understood and poorly implemented in comparison with the traditional academic curricula. One attempt to address this issue is through the establishment of school-industry partnerships. This paper explores the process of knowledge transfer between industry and schools in these partnerships. The paper theorises how knowledge that is valued and foundational in workplace employment can inform school curricula and pedagogical practices. The paper draws on theories of organisational knowledge, workplace learning and experiential learning to explore strategies that enhance school-to-employment transition outcomes.

Industry school partnerships: Boundary crossing to enable school to work transitions

Industry-school partnerships (ISPs) are increasingly being recognised as a new way of providing vocational education opportunities. However, there is limited research investigating their impact on school to work transitions. This paper reports on a government-led ISP, the Gateway to Industry Schools Program, established in Queensland, Australia. Central to this initiative is the Queensland Minerals and Energy Academy (QMEA), a lead organisation for 28 schools and 17 multi-national sponsor companies. This research adopted a qualitative case study methodology and draws upon boundary crossing theory as means to understand a Minerals and Energy ISP. We distinguish four types of boundary crossing mechanisms, which align with principles for effectiveness in ISPs. The main findings were that boundary crossing mechanisms assist ISPs to develop industry-based contextualised curriculum and to prepare school students for employment.