Review of current test methods for screwed connections

The pull-through/local dimpling failure strength of screwed connections is very important in the design of profiled steel cladding systems to help them resist storms and hurricanes. The current American and European provisions recommend four different test methods for the screwed connections in tension, but the accuracy of these methods in determining the connection strength is not known. It is unlikely that the four test methods are equivalent in all cases and thus it is necessary to reduce the number of methods recommended. This paper presents a review of these test methods based on some laboratory tests on crest- and valley-fixed claddings and then recommends alternative tests methods that reproduce the real behavior of the connections, including the bending and membrane deformations of the cladding around the screw fasteners and the tension load in the fastener.

Buckling experiments on hollow flange beams with web stiffeners

The hollow flange beam (HFB) is a new cold-formed and resistance-welded section developed in Australia. Due to its unique geometry comprising two stiff triangular flanges and a slender web, the HFB is susceptible to a lateral-distortional buckling mode of failure involving web distortion. Investigation using finite-element analyses showed that the use of transverse web plate stiffeners effectively eliminated lateral-distortional buckling of HFBs and thus any associated reduction in flexural capacity. A detailed experimental investigation was then carried out to validate the results from the finite-element analysis and to improve the stiffener configuration further. This led to the development of a special stiffener that is screw-fastened to the flanges on alternate sides of the web. This paper presents the details of the experimental investigations, the results, and the final stiffener arrangement whereas the details of the finite-element analyses are presented in a companion paper.

Pull-out strength of steel roof and wall cladding systems

When steel roof and wall cladding systems are subjected to wind uplift/suction forces, local pull-through/dimpling failures or pull-out failures occur prematurely at their screwed connections. During extreme wind events such as storms and hurricanes, these localized failures then lead to severe damage to buildings and their contents. An investigation was therefore carried out to study the failure that occurs when the screw fastener pulls out of the steel battens, purlins, or girts. Both two-span cladding tests and small-scale tests were conducted using a range of commonly used screw fasteners and steel battens, purlins, and girts. Experimental results showed that the current design formula may not be suitable unless a reduced capacity factor of 0.4 is used. Therefore, an improved design formula has been developed for pull-out failures in steel cladding systems. The formula takes into account thickness and ultimate tensile strength of steel, along with thread diameter and the pitch of screw fasteners, in order to model the pull-out behavior more accurately. This paper presents the details of this experimental investigation and its results.

Pull-through failures of crest-fixed steel claddings initiated by transverse splitting

Crest-fixed steel claddings made of thin, high strength steel often suffer from local pull-through failures at their screw connections during high wind events such as storms and hurricanes. Currently there aren't any adequate design provisions for these cladding systems except for the expensive testing provisions. Since the local pull-through failures in the less ductile steel claddings are initiated by transverse splitting at the fastener hole, analytical studies have not been able to determine the pull-through failure loads. Analytical studies could be used if a reliable splitting criterion is available. Therefore a series of two-span cladding tests was conducted on a range of crest-fixed steel cladding systems under simulated wind uplift loads. The strains in the sheeting around the critical fastener holes were measured until the pull-through failure. This paper presents the details of the experimental investigation and the results including a strain criterion for the local pull-through failure.

Cyclic pull-out strength of steel roof and wall cladding systems

When crest-fixed thin steel roof cladding systems are subjected to wind uplift, local pull-through or pull-out failures occur prematurely at their screwed connections. During high wind events such as storms and cyclones these localised failures then lead to severe damage to buildings and their contents. In recent times, the use of thin steel battens/purlins has increased considerably. This has made the pull-out failures more critical in the design of steel cladding systems. Recent research has developed a design formula for the static pull-out strength of steel cladding systems. However, the effects of fluctuating wind uplift loading that occurs during high wind events are not known. Therefore a series of constant amplitude cyclic tests has been undertaken on connections between steel battens made of different thicknesses and steel grades, and screw fasteners with varying diameter and pitch. This paper presents the details of these cyclic tests and the results.

Shear capacity of lipped channel beams with web openings : design rules and improvements

Cold-formed steel Lipped Channel Beams (LCB) with web openings are commonly used as floor joists and bearers in building structures. Shear behaviour of these beams is more complicated and their shear capacities are considerably reduced by the presence of web openings. Hence detailed numerical and experimental studies of simply supported LCBs under a mid-span load with aspect ratios of 1.0 and 1.5 were undertaken to investigate the shear behaviour and strength of LCBs with web openings. Experimental and numerical results showed that the current design rules in cold-formed steel structures design codes are very conservative. Improved design equations were therefore proposed for the shear strength of LCBs with web openings based on both experimental and numerical results. This research showed a significant reduction in shear capacities of LCBs when large web openings are included for the purpose of locating building services. A cost effective method of eliminating such detrimental effects of large circular web openings was also therefore investigated using experimental and numerical studies. For this purpose LCBS were reinforced using plate, stud, transverse and sleeve stiffeners with varying sizes and thicknesses that were welded and screw-fastened to the web of LCBs. These studies showed that plate stiffeners were the most suitable. Suitable screw-fastened plate stiffener arrangements with optimum thicknesses were then proposed for LCBs with web openings to restore their original shear capacities. This paper presents the details of finite element analyses and experiments of LCBs with web openings in shear, and the development of improved shear design rules. It then describes the experimental and numerical studies to determine the optimum plate stiffener arrangements and the results. The proposed shear design rules in this paper can be considered for inclusion in the future versions of cold-formed steel design codes.

Why nurses are resigning from rural and remote Queensland health facilities

This paper presents a selection of the results reported in the study “Factors Influencing the Recruitment and Retention of Rural and Remote Area Nurses in Queensland” (Hegney et al 2001). The main aim of this study was to determine why nurses in those rural and remote areas of Queensland that reported higher than State average turnover rates between February 1999 and May 2000, chose to leave their employment. The study therefore investigated the factors that influenced nurses' decisions to leave rural and remote area practice, the factors that influenced them to remain in practice and those factors nurses considered irrelevant to leaving or staying in rural/remote area nursing. This paper reports those factors the participants believed influenced them to leave rural and remote area nursing in Queensland. While the findings cannot be generalised to the Australian nursing workforce or to nurses not employed by Queensland Health, the study does confirm the findings of previous Australian research and formulates recommendations to assist future nursing workforce planning and policy.

Retaining rural and remote area nurses : The Queensland, Australia experience

Because higher-than-average turnover rates for nurses who work in remote and rural areas are the norm, the authors conducted a study to identify professional and personal factors that influenced rural nurses’ decisions to resign. Using a mail survey, the authors gathered qualitative and quantitative data from nurses who had resigned from rural and remote areas in Queensland, Australia. Their findings, categorized into professional and rural influences, highlight the importance of work force planning strategies that capitalize on the positive aspects of rural and remote area practice, to retain nurses in nonmetropolitan areas.

Retaining the thin blue line : What shapes workers' intentions not to quit the current work environment

Purpose – The purpose of this paper is to investigate the relationship between workplace factors and the intentions of police officers to quit their current department. Design/methodology/approach – Data from a survey of Baltimore officers, designed to examine the relationship between police stress and domestic violence in police families were used. Using multivariate regression analysis, the authors focus on the officers' stated intentions to look for alternative employment, with proxies for social and workplace factors. Findings – Higher levels of cooperation (trust), interactional justice and work-life-balance reduce police officers' intentions to quit. While high levels of physical and psychological strain and trauma are not correlated with intentions to quit. Research limitations/implications – A discernible limitation of this study is the age of the data analyzed and that many changes have occurred in recent times (policing and social). It would be of great interest to repeat this study to gauge the true effect. Practical implications – There are policy implications for retention and recruitment: it may possible to decrease the ethnic and gender gaps, through identifying officers at risk and creating programs to hold existing minorities, recruit more, whilst maintaining a strong, happy and healthy department. Originality/value – This study examines the impact of workplace factors on quitting intention for police officers. It is demonstrated that social capital, fairness and work-life balance are moderators for quitting, adding to the literature on worker retention, as little research has been done using multivariate analysis on quitting intentions.

Clinical skin examination outcomes after a video-based behavioral intervention analysis from a randomized clinical trial

Importance Older men are at risk of dying of melanoma. Objective To assess attendance at and clinical outcomes of clinical skin examinations (CSEs) in older men exposed to a video-based behavioral intervention. Design, Setting, and Participants This was a behavioral randomized clinical trial of a video-based intervention in men aged at least 50 years. Between June 1 and August 31, 2008, men were recruited, completed baseline telephone interviews, and were than randomized to receive either a video-based intervention (n = 469) or brochures only (n = 461; overall response rate, 37.1%) and were again interviewed 7 months later (n = 870; 93.5% retention). Interventions Video on skin self-examination and skin awareness and written informational materials. The control group received written materials only. Main Outcomes and Measures Participants who reported a CSE were asked for the type of CSE (skin spot, partial body, or whole body), who initiated it, whether the physician noted any suspicious lesions, and, if so, how lesions were managed. Physicians completed a case report form that included the type of CSE, who initiated it, the number of suspicious lesions detected, how lesions were managed (excision, nonsurgical treatment, monitoring, or referral), and pathology reports after lesion excision or biopsy. Results Overall, 540 of 870 men (62.1%) self-reported a CSE since receiving intervention materials, and 321 of 540 (59.4%) consented for their physician to provide medical information (received for 266 of 321 [82.9%]). Attendance of any CSE was similar between groups (intervention group, 246 of 436 [56.4%]; control group, 229 of 434 [52.8%]), but men in the intervention group were more likely to self-report a whole-body CSE (154 of 436 [35.3%] vs 118 of 434 [27.2%] for control group; P = .01). Two melanomas, 29 squamous cell carcinomas, and 38 basal cell carcinomas were diagnosed, with a higher proportion of malignant lesions in the intervention group (60.0% vs 40.0% for controls; P = .03). Baseline attitudes, behaviors, and skin cancer history were associated with higher odds of CSE and skin cancer diagnosis. Conclusions and Relevance A video-based intervention may increase whole-body CSE and skin cancer diagnosis in older men. Trial Registration: anzctr.org.au Identifier: ACTRN12608000384358

Developing Performance Mentoring Handbook

Over the last 40 years, the term mentoring has been hailed as an important workplace learning activity, and applied in a variety on contexts such as government departments, hospitals, schools and community settings. It has been used to support the learning and development of new employees and leaders, as well as for the purposes of talent management and retention. Not surprisingly, its meaning often depends on the purpose for which it has been used and the particular context in which it has been applied. Most adults can identify a person who has had a major positive impact on their lives, e.g. a boss, a coach or a teacher, who has acted as a mentor to them. Today, organisations are embracing the concept of mentoring as a professional development too through which improvements in efficiency, productivity and the passing of corporate knowledge and leadership skills can occur.

Design, implementation and multisite evaluation of a system suitability protocol for the quantitative assessment of instrument performance in liquid chromatography-multiple reaction monitoring-MS (LC-MRM-MS)

Multiple reaction monitoring (MRM) mass spectrometry coupled with stable isotope dilution (SID) and liquid chromatography (LC) is increasingly used in biological and clinical studies for precise and reproducible quantification of peptides and proteins in complex sample matrices. Robust LC-SID-MRM-MS-based assays that can be replicated across laboratories and ultimately in clinical laboratory settings require standardized protocols to demonstrate that the analysis platforms are performing adequately. We developed a system suitability protocol (SSP), which employs a predigested mixture of six proteins, to facilitate performance evaluation of LC-SID-MRM-MS instrument platforms, configured with nanoflow-LC systems interfaced to triple quadrupole mass spectrometers. The SSP was designed for use with low multiplex analyses as well as high multiplex approaches when software-driven scheduling of data acquisition is required. Performance was assessed by monitoring of a range of chromatographic and mass spectrometric metrics including peak width, chromatographic resolution, peak capacity, and the variability in peak area and analyte retention time (RT) stability. The SSP, which was evaluated in 11 laboratories on a total of 15 different instruments, enabled early diagnoses of LC and MS anomalies that indicated suboptimal LC-MRM-MS performance. The observed range in variation of each of the metrics scrutinized serves to define the criteria for optimized LC-SID-MRM-MS platforms for routine use, with pass/fail criteria for system suitability performance measures defined as peak area coefficient of variation <0.15, peak width coefficient of variation <0.15, standard deviation of RT <0.15 min (9 s), and the RT drift <0.5min (30 s). The deleterious effect of a marginally performing LC-SID-MRM-MS system on the limit of quantification (LOQ) in targeted quantitative assays illustrates the use and need for a SSP to establish robust and reliable system performance. Use of a SSP helps to ensure that analyte quantification measurements can be replicated with good precision within and across multiple laboratories and should facilitate more widespread use of MRM-MS technology by the basic biomedical and clinical laboratory research communities.

Management of endocrine resistant breast cancer

Metastatic breast cancer (MBC) may present de novo but more commonly develops in women initially presenting with early breast cancer despite the widespread use of adjuvant hormonal and cytotoxic chemotherapy. MBC is incurable. Hormone sensitive MBC eventually becomes resistant to endocrine therapy in most women. Anthracyclines are the agents of choice in the treatment of endocrine resistant MBC. With the widespread use of anthracyclines in the adjuvant setting, taxanes have become the agents of choice for many patients. Recently capecitabine has become established as a standard of care for patients pretreated with anthracyclines and taxanes. However, a range of agents have activity as third line treatment. These include gemcitabine, vinorelbine and platinum analogues. The sequential use of non-cross resistant single agents rather than combination therapy is preferable in most women with MBC. Even though combination therapy can improve response rates and increase progression free interval, there is no robust evidence to indicate an advantage in terms of overall survival. Moreover, combination therapy is associated with a higher toxicity rate and poor quality of life. There is no role for dose-intense therapy, high dose therapy or maintenance chemotherapy outside the context of a clinical trial. The introduction of trastuzumab, monoclonal antibody targeting growth factor receptors, has improved the therapeutic options for women with tumours overexpressing HER2/neu. DNA micro-array profiles of tumours can potentially help to individualise therapy in future. Molecular targeted therapy has the potential to revolutionise the management of MBC.

Ensuring sessional academic success by rethinking the place of academic development

There has been growing recognition of the contribution that Sessional Academics make to student learning in higher education; with recent studies concluding that around half Australian university teaching is now performed by casual staff [Red Report 2008; May, 2013]. However, sector-wide research and institutional audits continue to raise concerns about academic development and quality assurance, as well as the recognition and retention of Sessional Academics. In response, universities offer academic development programs. However, while such centrally offered programs are undoubtedly useful, they are necessarily generic and cannot address the local contexts of faculties or provide ‘on the ground’ support. This paper presents a new, distributed model of academic support and development for Sessional academics at Queensland University of Technology. Entitled the Sessional Academic Success program, it employs the principles of distributed leadership. Experienced Sessional academics are trained and supported to assume roles as Sessional Academic Success Advisors within their schools. Complementing our central programs, they design bespoke, locally situated, peer-to-peer academic development for new Sessional teachers; provide ‘just in time’, safe and reliable advice; and build supportive communities of teaching practice in their local contexts. This distributed model re-envisages the forms and places of academic development and support. It helps ensure that new Sessional Academics are embraced by faculty life. And, recognizing that experienced Sessional Academics have much to contribute to the advancement of learning and teaching, it builds their capacity through leadership opportunities. As the designer/facilitator of the program and a Sessional Academic Success Advisor, the authors take a dialogic approach and together describe the design, implementation and outcomes of the program.

Footprints to pathways : reconciliation action planning in industry to sustain Indigenous employment in Queensland

This paper provides an introductory discussion to a study focusing on industry Reconciliation Action Plans (RAP) and sustaining Indigenous employment in Queensland. Indigenous people continue to experience deep and persistent disadvantage in employment, which limits their life prospects (McLachlan, Gilgillan & Gordon, 2013). A major contributing factor to this detriment is irregular employment and or unemployment. A reasonable standard of living has been found to be determined by access to economic resources such as income and wealth. Denial of this access, denies access to income streams, social status, and engagement in meaningful activities. Hence, job loss and joblessness are triggers of disadvantage (McLachlan, et al., 2013). For young Indigenous people, lack of access has lasting effects particularly if they have multiple characteristics that place them at risk of disadvantage. The project aims to develop knowledge and understanding of Industry RAPs mediate employment opportunities for Indigenous people and how young Indigenous people conceive of their employment options and the processes by which employers can best support Indigenous people. It adopts two theoretical frameworks to investigate the aim of the study : (1) Lave and Wenger’s (1991) theory of communities of practice and, (2) Sen’s (1993) capability approach which provides a structure for examining individual well-being in the context of societal inequality. This paper discusses the first research question of the study: What are Industry Reconciliation Action Plans? What is included in RAPs? Why do Industries develop RAPs? How do RAPs attract, recruit, retain, and tenure Indigenous people? The project’s significance rests with its focus on Industry, employers, policies and practices that aid the attraction and retention of Indigenous people in employment.