THEORETICAL ROAD DAMAGE DUE TO DYNAMIC TYRE FORCES OF HEAVY VEHICLES. PART 1: DYNAMIC ANALYSIS OF VEHICLES AND ROAD SURFACES.

Theory is presented for simulating the dynamic wheel forces generated by heavy road vehicles and the resulting dynamic response of road surfaces to these loads. Sample calculations are provided and the vehicle simulation is validated with data from full-scale tests. The methods are used in the accompanying paper to simulate the road damage done by a tandem-axle vehicle.

THEORETICAL ROAD DAMAGE DUE TO DYNAMIC TYRE FORCES OF HEAVY VEHICLES. PART 2: SIMULATED DAMAGE CAUSED BY A TANDEM-AXLE VEHICLE.

The literature relating to road surface failure and design is briefly reviewed and the conventional methods for assessing the road damaging effects of dynamic tire forces are examined. A new time domain technique for analyzing dynamic tire forces and four associated road damage criteria are presented. The force criteria are used to examine the road damaging characteristics of a simple tandem-axle vehicle model for a range of speed and road roughness conditions. It is concluded that for the proposed criteria, the theoretical service life of road surfaces that are prone to fatigue failure may be reduced significantly by the dynamic component of wheel forces. The damage done to approximately five per cent of the road surface area during the passage of a theoretical model vehicle at typical highway speeds may be increased by as much as four times.

Road damage due to dynamic tyre forces measured on a public road

This paper describes a series of tests conducted on a UK trunk road, in which the dynamic tyre forces generated by over 1500 heavy goods vehicles (HGVs) were measured using a load measuring mat containing 144 capacitive strip sensors. The data was used to investigate the relative road damaging potential of the various classes of vehicles, and the degree of spatial repeatability of tyre forces present in a typical highway fleet. Approximately half the vehicles tested were found to contribute to a spatially repeatable pattern of pavement loading. On average, air suspended vehicles were found to generate lower dynamic load coefficients than steel suspended vehicles. However, air suspended vehicles also generated higher mean levels of theoretical road damage (aggregate force) than steel suspended vehicles, indicating that the ranking of suspensions depends on the pavement damage criterion used.

Characterisation and simulation of asphalt road surfaces

Accurate simulation of rolling-tyre vibrations, and the associated noise, requires knowledge of road-surface topology. Full scans of the surface types in common use are, however, not widely available, and are likely to remain so. Ways of producing simulated surfaces from incomplete starting information are thus needed. In this paper, a simulation methodology based solely on line measurements is developed, and validated against a full two-dimensional height map of a real asphalt surface. First the tribological characteristics-asperity height, curvature and nearest-neighbour distributions-of the real surface are analysed. It is then shown that a standard simulation technique, which matches the (isotropic) spectrum and the probability distribution of the height measurements, is unable to reproduce these characteristics satisfactorily. A modification, whereby the inherent granularity of the surface is enforced at the initialisation stage, is introduced, and found to produce simulations whose tribological characteristics are in excellent agreement with the measurements. This method will thus make high-fidelity tyre-vibration calculations feasible for researchers with access to line-scan data only. In addition, the approach to surface tribological characterisation set out here provides a template for efficient cataloguing of road textures, as long as the resulting information can subsequently be used to produce sample realisations. A third simulation algorithm, which successfully addresses this requirement, is therefore also presented. © 2011 Elsevier B.V.

Gene admixture in the Silk Road region of China: Evidence from mtDNA and melanocortin 1 receptor polymorphism

Mitochondrial DNA control region segment I sequences and melanocortin 1 receptor (MC1R) gene polymorphism were examined in ethnic populations in the silk road region of China. Both the frequencies of the MC1R variants and the results of mtDNA data in this region presented intermediate values between those of Europe and East and Southeast Asia, which suggested extensive gene admixture in this area and was in general agreement with previous studies. Phylogenetic analysis of the ethnic populations in the Silk Road region that based on mtDNA data didn't show expected cluster pattern according to their ethnogenesis. We suspect that a high migration rate in female among these closely related populations and other three demographic events might account for it.

Different matrilineal contributions to genetic structure of ethnic groups in the Silk Road region in China

Previous studies have shown that there were extensive genetic admixtures in the Silk Road region. In the present study, we analyzed 252 mtDNAs of five ethnic groups (Uygur, Uzbek, Kazak, Mongolian, and Hui) from Xinjiang Province, China (through which the

The long road to freedom: the end of apartheid has signalled a new beginning for women in South Africa’s fisheries but real equality is still a far-off dream

Women in fishing communities are increasingly moving from traditional, community based occupations to seeking employment in the labour market. While this is an opportunity for women, their employment is also largely in the male dominated fishing industry, where job segregation into ‘less skilled and low paid’ jobs for women define employment opportunities. However, engagement as members in local non-government networks help women to challenge these stereotypes. In South Africa, for instance, the recent legislation promoting opportunity for women in male dominated sectors of employment is an opportunity for women to earn wages equal to those of men.

Re-examination of the coefficient of determination (r2) using road materials engineering case studies

The analysis of scientific data is integral to materials engineering and science. The correlation between measured variables is often quantified by estimating the coefficient of determination or the r2 value. This is the recognised procedure for determining linear relationships. The authors review the derivation of the r2 value and derive an associated quantity, termed the relative deviation (RD), which is the ratio of the root mean square of the deviations about the fitted line to the root mean square of the deviations about the y bar line expressed as a percentage. The relative deviation has an advantage over the coefficient of determination in that it has greater numerical sensitivity to changes in the spread of data about the fitted line, especially when the scatter is small. In addition, the relative deviation is able to define, in percentage terms, the reduction in scatter when different independent variables are correlated with a common dependent variable. Four case studies in the materials field (aggregate crushing value, Atterberg limits, permeability and creep of asphalt) from work carried out at the Queensland Main Roads Department are presented to show the use of the new parameter RD.

Prediction of tread block forces for a free-rolling tyre in contact with a rough road

This paper describes a new approach to model the forces on a tread block for a free-rolling tyre in contact with a rough road. A theoretical analysis based on realistic tread mechanical properties and road roughness is presented, indicating partial contact between a tread block and a rough road. Hence an asperity-scale indentation model is developed using a semi-empirical formulation, taking into account both the rubber viscoelasticity and the tread block geometry. The model aims to capture the essential details of the contact at the simplest level, to make it suitable as part of a time-domain dynamic analysis of the coupled tyre-road system. The indentation model is found to have a good correlation with the finite element (FE) predictions and is validated against experimental results using a rolling contact rig. When coupled to a deformed tyre belt profile, the indentation model predicts normal and tangential force histories inside the tyre contact patch that show good agreement with FE predictions. © 2012 Elsevier B.V..