Configuration management and product lines to enhance the replication process in software engineering

This research is concerned with the experimental software engineering area, specifically experiment replication. Replication has traditionally been viewed as a complex task in software engineering. This is possibly due to the present immaturity of the experimental paradigm applied to software development. Researchers usually use replication packages to replicate an experiment. However, replication packages are not the solution to all the information management problems that crop up when successive replications of an experiment accumulate. This research borrows ideas from the software configuration management and software product line paradigms to support the replication process. We believe that configuration management can help to manage and administer information from one replication to another: hypotheses, designs, data analysis, etc. The software product line paradigm can help to organize and manage any changes introduced into the experiment by each replication. We expect the union of the two paradigms in replication to improve the planning, design and execution of further replications and their alignment with existing replications. Additionally, this research work will contribute a web support environment for archiving information related to different experiment replications. Additionally, it will provide flexible enough information management support for running replications with different numbers and types of changes. Finally, it will afford massive storage of data from different replications. Experimenters working collaboratively on the same experiment must all have access to the different experiments.

Calibration process on the study of new antenna array architectures for space communications

This paper introduces novel calibration processes applied to antenna arrays with new architectures and technologies designed to improve the performance of traditional earth stations for satellite communications due to the increasing requirement of data capacity during last decades. Besides, the Radiation Group from the Technical University of Madrid has been working on the development of new antenna arrays based on novel architecture and technologies along many projects as a solution for the ground segment in the early future. Nowadays, the calibration process is an interesting and cutting edge research field in a period of expansion with a lot of work to do for calibration in transmission and also for reception of these novel antennas under development.

Including hardware/software co-design in the ASSERT model driven engineering process.

Abstract. The ASSERT project de?ned new software engineering methods and tools for the development of critical embedded real-time systems in the space domain. The ASSERT model-driven engineering process was one of the achievements of the project and is based on the concept of property- preserving model transformations. The key element of this process is that non-functional properties of the software system must be preserved during model transformations. Properties preservation is carried out through model transformations compliant with the Ravenscar Pro?le and provides a formal basis to the process. In this way, the so-called Ravenscar Computational Model is central to the whole ASSERT process. This paper describes the work done in the HWSWCO study, whose main objective has been to address the integration of the Hardware/Software co-design phase in the ASSERT process. In order to do that, non-functional properties of the software system must also be preserved during hardware synthesis. Keywords : Ada 2005, Ravenscar pro?le, Hardware/Software co-design, real- time systems, high-integrity systems, ORK

Traditional education vs modern education. What is the impact of teaching techniques' evolution on students learning process?

The main objective of this article is to focus on the analysis of teaching techniques, ranging from the use of the blackboard and chalk in old traditional classes, using slides and overhead projectors in the eighties and use of presentation software in the nineties, to the video, electronic board and network resources nowadays. Furthermore, all the aforementioned, is viewed under the different mentalities in which the teacher conditions the student using the new teaching technique, improving soft skills but maybe leading either to encouragement or disinterest, and including the lack of educational knowledge consolidation at scientific, technology and specific levels. In the same way, we study the process of adaptation required for teachers, the differences in the processes of information transfer and education towards the student, and even the existence of teachers who are not any longer appealed by their work due which has become much simpler due to new technologies and the greater ease in the development of classes due to the criteria described on the new Grade Programs adopted by the European Higher Education Area. Moreover, it is also intended to understand the evolution of students’ profiles, from the eighties to present time, in order to understand certain attitudes, behaviours, accomplishments and acknowledgements acquired over the semesters within the degree Programs. As an Educational Innovation Group, another key question also arises. What will be the learning techniques in the future?. How these evolving matters will affect both positively and negatively on the mentality, attitude, behaviour, learning, achievement of goals and satisfaction levels of all elements involved in universities’ education? Clearly, this evolution from chalk to the electronic board, the three-dimensional view of our works and their sequence, greatly facilitates the understanding and adaptation later on to the business world, but does not answer to the unknowns regarding the knowledge and the full development of achievement’s indicators in basic skills of a degree. This is the underlying question which steers the roots of the presented research.

Influencia de la maquinaria agrícola sobre la variabilidad espacial de la compactación del suelo. Aplicación de la metodología geoestadística-fractal

El cultivo de la caña de azúcar es uno de los más importantes en muchos países del mundo. Los suelos dedicados a este cultivo son usualmente compactados por el tránsito de la maquinaria en el proceso de cosecha. El uso combinado de la geoestadística con el análisis fractal ha demostrado ser útil para el estudio de los mismos. El objetivo del trabajo fue determinar los cambios espaciales de la resistencia a la penetración del suelo debido a la influencia del tránsito de la maquinaria en el proceso de cosecha de la caña de azúcar en un Vertisol, aplicando la metodología geoestadística-fractal. La investigación se llevó a cabo en el período de cosecha 2008-2009. Se evaluó la resistencia a la penetración en dos momentos, antes y después de la cosecha. El muestreo se realizó sistemáticamente en cuadrícula y en transecto, seleccionando 144 y 100 observaciones antes y después de la cosecha, respectivamente, y 221 para el transecto en diagonal. También se determinó el contenido de humedad del suelo por el método gravimétrico, para lo que se tomaron 288 muestras aleatorias en todo el campo. Los resultados demuestran que los valores de resistencia a la penetración (RP) presentaron una distribución normal a partir de los 5 cm de profundidad, el tránsito de la maquinaria agrícola para la cosecha de la caña de azúcar provocó concentración de la variabilidad espacial a escalas inferiores a la del muestreo (el efecto pepita aumentó), un aumento del rango de correlación espacial y una redistribución de las zonas de compactación (las variaciones de los mapas de Krigeaje). También indujo anti-persistencia y anisotropía en algunas direcciones horizontales. Se observó un comportamiento irregular de (RP) verticalmente en el transecto, donde no solamente influyó la maquinaria, sino que también otros factores influyeron como: la hilera, borde de la hilera y grietas. ABSTRACT The cultivation of the cane of sugar is one of the most important in many countries of the world. The soils dedicated to this cultivation are usually compacted by the traffic of the machinery in the harvest process. The combined use of the geostatistics with the fractal analysis has demonstrated to be useful for the study of the same ones. The objective of the work was to determine the space changes from the resistance to the penetration of the floor due to the influence of the traffic of the machinery in the harvest process of harvest of the cane of sugar in a Vertisol applying the geostatistic-fractal methodology. The investigation was carried out in the period of harvest 2008-2009. The resistance to the penetration at two moments was evaluated, before and after the harvest. The sampling was realized systematically in grid and transect, selecting 144 and 100 observations before and after the harvest, respectively, and 221 for transect in diagonal. Also the soil moisture content of the ground by the gravimetric method was determined, so 288 random samples in the entire field were taken. The results shown that resistance to penetration values presented a normal distribution deeper than 5 cm before and after harvest. The transit of the agricultural machinery for sugar cane harvest concentrated the space variability at lower distances than the sampling one, reflected an increase in the nugget effect. At the same time, an increase space correlation rank and a redistribution of compaction areas were observed studying the variations in kriging maps. Another effect of the agricultural machinery transit was to induce antipersistence and anisotropy in some horizontal directions. However, in vertical direction of the longest transect an irregular behaviour was induced not only by the machinery as by another factors such as soil cracks, crop rows and allocation.

Advanced Fresnel Köhler concentrators for photovoltaic applications

La concentración fotovoltaica (CPV) es una de las formas más prometedoras de reducir el coste de la energía proveniente del sol. Esto es posible gracias a células solares de alta eficiencia y a una significativa reducción del tamaño de la misma, que está fabricada con costosos materiales semiconductores. Ambos aspectos están íntimamente ligados ya que las altas eficiencias solamente son posibles con materiales y tecnologías de célula caros, lo que forzosamente conlleva una reducción del tamaño de la célula si se quiere lograr un sistema rentable. La reducción en el tamaño de las células requiere que la luz proveniente del sol ha de ser redirigida (es decir, concentrada) hacia la posición de la célula. Esto se logra colocando un concentrador óptico encima de la célula. Estos concentradores para CPV están formados por diferentes elementos ópticos fabricados en materiales baratos, con el fin de reducir los costes de producción. El marco óptimo para el diseño de concentradores es la óptica anidólica u óptica nonimaging. La óptica nonimaging fue desarrollada por primera vez en la década de los años sesenta y ha ido evolucionando significativamente desde entonces. El objetivo de los diseños nonimaging es la transferencia eficiente de energía entre la fuente y el receptor (sol y célula respectivamente, en el caso de la CPV), sin tener en cuenta la formación de imagen. Los sistemas nonimaging suelen ser simples, están compuestos de un menor número de superficies que los sistemas formadores de imagen y son más tolerantes a errores de fabricación. Esto hace de los sistemas nonimaging una herramienta fundamental, no sólo en el diseño de concentradores fotovoltaicos, sino también en el diseño de otras aplicaciones como iluminación, proyección y comunicaciones inalámbricas ópticas. Los concentradores ópticos nonimaging son adecuados para aplicaciones CPV porque el objetivo no es la reproducción de una imagen exacta del sol (como sería el caso de las ópticas formadoras de imagen), sino simplemente la colección de su energía sobre la célula solar. Los concentradores para CPV pueden presentar muy diferentes arquitecturas y elementos ópticos, dando lugar a una gran variedad de posibles diseños. El primer elemento óptico que es atravesado por la luz del sol se llama Elemento Óptico Primario (POE en su nomenclatura anglosajona) y es el elemento más determinante a la hora de definir la forma y las propiedades del concentrador. El POE puede ser refractivo (lente) o reflexivo (espejo). Esta tesis se centra en los sistemas CPV que presentan lentes de Fresnel como POE, que son lentes refractivas delgadas y de bajo coste de producción que son capaces de concentrar la luz solar. El capítulo 1 expone una breve introducción a la óptica geométrica y no formadora de imagen (nonimaging), explicando sus fundamentos y conceptos básicos. Tras ello, la integración Köhler es presentada en detalle, explicando sus principios, válidos tanto para aplicaciones CPV como para iluminación. Una introducción a los conceptos fundamentales de CPV también ha sido incluida en este capítulo, donde se analizan las propiedades de las células solares multiunión y de los concentradores ópticos empleados en los sistemas CPV. El capítulo se cierra con una descripción de las tecnologías existentes empleadas para la fabricación de elementos ópticos que componen los concentradores. El capítulo 2 se centra principalmente en el diseño y desarrollo de los tres concentradores ópticos avanzados Fresnel Köhler que se presentan en esta tesis: Fresnel-Köhler (FK), Fresnel-Köhler curvo (DFK) y Fresnel-Köhler con cavidad (CFK). Todos ellos llevan a cabo integración Köhler y presentan una lente de Fresnel como su elemento óptico primario. Cada uno de estos concentradores CPV presenta sus propias propiedades y su propio procedimiento de diseño. Además, presentan todas las características que todo concentrador ha de tener: elevado factor de concentración, alta tolerancia de fabricación, alta eficiencia óptica, irradiancia uniforme sobre la superficie de la célula y bajo coste de producción. Los concentradores FK y DFK presentan una configuración de cuatro sectores para lograr la integración Köhler. Esto quiere decir que POE y SOE se dividen en cuatro sectores simétricos cada uno, y cada sector del POE trabaja conjuntamente con su correspondiente sector de SOE. La principal diferencia entre los dos concentradores es que el POE del FK es una lente de Fresnel plana, mientras que una lente curva de Fresnel es empleada como POE del DFK. El concentrador CFK incluye una cavidad de confinamiento externo integrada, que es un elemento óptico capaz de recuperar los rayos reflejados por la superficie de la célula con el fin de ser reabsorbidos por la misma. Por tanto, se aumenta la absorción de la luz, lo que implica un aumento en la eficiencia del módulo. Además, este capítulo también explica un método de diseño alternativo para los elementos faceteados, especialmente adecuado para las lentes curvas como el POE del DFK. El capítulo 3 se centra en la caracterización y medidas experimentales de los concentradores ópticos presentados en el capítulo 2, y describe sus procedimientos. Estos procedimientos son en general aplicables a cualquier concentrador basado en una lente de Fresnel, e incluyen tres tipos principales de medidas experimentales: eficiencia eléctrica, ángulo de aceptancia y uniformidad de la irradiancia en el plano de la célula. Los resultados que se muestran a lo largo de este capítulo validarán a través de medidas a sol real las características avanzadas que presentan los concentradores Köhler, y que se demuestran en el capítulo 2 mediante simulaciones de rayos. Cada concentrador (FK, DFK y CFK) está diseñado y optimizado teniendo en cuenta condiciones de operación realistas. Su rendimiento se modela de forma exhaustiva mediante el trazado de rayos en combinación con modelos distribuidos para la célula. La tolerancia es un asunto crítico de cara al proceso de fabricación, y ha de ser máxima para obtener sistemas de producción en masa rentables. Concentradores con tolerancias limitadas generan bajadas significativas de eficiencia a nivel de array, causadas por el desajuste de corrientes entre los diferentes módulos (principalmente debido a errores de alineación en la fabricación). En este sentido, la sección 3.5 presenta dos métodos matemáticos que estiman estas pérdidas por desajuste a nivel de array mediante un análisis de sus curvas I-V, y por tanto siendo innecesarias las medidas a nivel de mono-módulo. El capítulo 3 también describe la caracterización indoor de los elementos ópticos que componen los concentradores, es decir, de las lentes de Fresnel que actúan como POE y de los secundarios free-form. El objetivo de esta caracterización es el de evaluar los adecuados perfiles de las superficies y las transmisiones ópticas de los diferentes elementos analizados, y así hacer que el rendimiento del módulo sea el esperado. Esta tesis la cierra el capítulo 4, en el que la integración Köhler se presenta como una buena alternativa para obtener distribuciones uniformes en aplicaciones de iluminación de estado sólido (iluminación con LED), siendo particularmente eficaz cuando se requiere adicionalmente una buena mezcla de colores. En este capítulo esto se muestra a través del ejemplo particular de un concentrador DFK, el cual se ha utilizado para aplicaciones CPV en los capítulos anteriores. Otra alternativa para lograr mezclas cromáticas apropiadas está basada en un método ya conocido (deflexiones anómalas), y también se ha utilizado aquí para diseñar una lente TIR aplanética delgada. Esta lente cumple la conservación de étendue, asegurando así que no hay bloqueo ni dilución de luz simultáneamente. Ambos enfoques presentan claras ventajas sobre las técnicas clásicas empleadas en iluminación para obtener distribuciones de iluminación uniforme: difusores y mezcla caleidoscópica mediante guías de luz. ABSTRACT Concentrating Photovoltaics (CPV) is one of the most promising ways of reducing the cost of energy collected from the sun. This is possible thanks to both, very high-efficiency solar cells and a large decrease in the size of cells, which are made of costly semiconductor materials. Both issues are closely linked since high efficiency values are only possible with expensive cell materials and technologies, implying a compulsory area reduction if cost-effectiveness is desired. The reduction in the cell size requires that light coming from the sun must be redirected (i.e. concentrated) towards the cell position. This is achieved by placing an optical concentrator system on top of the cell. These CPV concentrators consist of different optical elements manufactured on cheap materials in order to maintain low production costs. The optimal framework for the design of concentrators is nonimaging optics. Nonimaging optics was first developed in the 60s decade and has been largely developed ever since. The aim of nonimaging devices is the efficient transfer of light power between the source and the receiver (sun and cell respectively in the case of CPV), disregarding image formation. Nonimaging systems are usually simple, comprised of fewer surfaces than imaging systems and are more tolerant to manufacturing errors. This renders nonimaging optics a fundamental tool, not only in the design of photovoltaic concentrators, but also in the design of other applications as illumination, projection and wireless optical communications. Nonimaging optical concentrators are well suited for CPV applications because the goal is not the reproduction of an exact image of the sun (as imaging optics would provide), but simply the collection of its energy on the solar cell. Concentrators for CPV may present very different architectures and optical elements, resulting in a vast variety of possible designs. The first optical element that sunlight goes through is called the Primary Optical Element (POE) and is the most determinant element in order to define the shape and properties of the whole concentrator. The POE can be either refractive (lens) or reflective (mirror). This thesis focuses on CPV systems based on Fresnel lenses as POE, which are thin and inexpensive refractive lenses able to concentrate sunlight. Chapter 1 exposes a short introduction to geometrical and nonimaging optics, explaining their fundamentals and basic concepts. Then, the Köhler integration is presented in detail, explaining its principles, valid for both applications: CPV and illumination. An introduction to CPV fundamental concepts is also included in this chapter, analyzing the properties of multijunction solar cells and optical concentrators employed in CPV systems. The chapter is closed with a description of the existing technologies employed for the manufacture of optical elements composing the concentrator. Chapter 2 is mainly devoted to the design and development of the three advanced Fresnel Köhler optical concentrators presented in this thesis work: Fresnel-Köhler (FK), Dome-shaped Fresnel-Köhler (DFK) and Cavity Fresnel-Köhler (CFK). They all perform Köhler integration and comprise a Fresnel lens as their Primary Optical Element. Each one of these CPV concentrators presents its own characteristics, properties and its own design procedure. Their performances include all the key issues in a concentrator: high concentration factor, large tolerances, high optical efficiency, uniform irradiance on the cell surface and low production cost. The FK and DFK concentrators present a 4-fold configuration in order to perform the Köhler integration. This means that POE and SOE are divided into four symmetric sectors each one, working each POE sector with its corresponding SOE sector by pairs. The main difference between both concentrators is that the POE of the FK is a flat Fresnel lens, while a dome-shaped (curved) Fresnel lens performs as the DFK’s POE. The CFK concentrator includes an integrated external confinement cavity, which is an optical element able to recover rays reflected by the cell surface in order to be re-absorbed by the cell. It increases the light absorption, entailing an increase in the efficiency of the module. Additionally, an alternative design method for faceted elements will also be explained, especially suitable for dome-shaped lenses as the POE of the DFK. Chapter 3 focuses on the characterization and experimental measurements of the optical concentrators presented in Chapter 2, describing their procedures. These procedures are in general applicable to any Fresnel-based concentrator as well and include three main types of experimental measurements: electrical efficiency, acceptance angle and irradiance uniformity at the solar cell plane. The results shown along this chapter will validate through outdoor measurements under real sun operation the advanced characteristics presented by the Köhler concentrators, which are demonstrated in Chapter 2 through raytrace simulation: high optical efficiency, large acceptance angle, insensitivity to manufacturing tolerances and very good irradiance uniformity on the cell surface. Each concentrator (FK, DFK and CFK) is designed and optimized looking at realistic performance characteristics. Their performances are modeled exhaustively using ray tracing combined with cell modeling, taking into account the major relevant factors. The tolerance is a critical issue when coming to the manufacturing process in order to obtain cost-effective mass-production systems. Concentrators with tight tolerances result in significant efficiency drops at array level caused by current mismatch among different modules (mainly due to manufacturing alignment errors). In this sense, Section 3.5 presents two mathematical methods that estimate these mismatch losses for a given array just by analyzing its full-array I-V curve, hence being unnecessary any single mono-module measurement. Chapter 3 also describes the indoor characterization of the optical elements composing the concentrators, i.e. the Fresnel lenses acting as POEs and the free-form SOEs. The aim of this characterization is to assess the proper surface profiles and optical transmissions of the different elements analyzed, so they will allow for the expected module performance. This thesis is closed by Chapter 4, in which Köhler integration is presented as a good approach to obtain uniform distributions in Solid State Lighting applications (i.e. illumination with LEDs), being particularly effective when dealing with color mixing requirements. This chapter shows it through the particular example of a DFK concentrator, which has been used for CPV applications in the previous chapters. An alternative known method for color mixing purposes (anomalous deflections) has also been used to design a thin aplanatic TIR lens. This lens fulfills conservation of étendue, thus ensuring no light blocking and no light dilution at the same time. Both approaches present clear advantages over the classical techniques employed in lighting to obtain uniform illumination distributions: diffusers and kaleidoscopic lightpipe mixing.

La arquitectura residencial en El Real Sitio de El Pardo (1885 - 1965): Orígenes, tipos y configuración del trazado urbano

Tras la denominación de Real Sitio a mediados del siglo XVIII, bajo el reinado de Fernando VI, su sucesor Carlos III procedió a la incorporación a su Patrimonio de todos los Montes y Bosques de El Pardo. Comenzó entonces el proceso de planeamiento urbano y de construcción arquitectónica que finalizó en torno al año 1800. En lo sucesivo, no sólo se mantiene el curso de la conservación y consolidación de los edificios principales, sino que se realiza obra nueva de índole civil. Algunos edificios cambiaron de propiedad y de uso hasta que tras la Guerra Civil se procedió a la mayor transformación vivida por el Real Sitio. El intervalo que aquí se trata (1885 a 1965), no ha suscitado, en los estudios sobre El Pardo, atención suficiente al no acontecer obra nueva de carácter patrimonial ni ha sido objeto de análisis el trazado y la fisonomía del centro urbano residencial del pueblo que Carlos III configuró. Sin embargo se estima relevante analizar los cambios en la actividad residencial; en primer lugar porque coexiste con la arquitectura oficial y, por tanto, se entiende necesario un análisis global del conjunto y en segundo lugar porque facilita la comprensión sobre la imagen original de carácter histórico del conjunto de finales del siglo XVIII. Este marco temporal determina tres partes principales de estudio que estructuran la presente tesis, cuyas fechas establecen los intervalos históricos clave: Actuaciones sobre el núcleo urbano consolidado (1885-1931). Cese de la actividad constructiva (1931-1939). Propuestas regeneradoras y crecimiento acelerado (1939-1965). Dentro de ellos se establecen, a su vez, dos subcapítulos diferenciados con la finalidad de explicar los sucesos que pautaron los cambios trascendentales en la historia de El Pardo. En el estudio del estado de la cuestión se observa que en El Pardo, al igual que sucede en otros Reales Sitios, se investigan los edificios destacados como el Palacio, la Casita del Príncipe, la Casa de Oficios y la Casa de Infantes desde el punto de vista de su historia pero no desde la arquitectura ni de cómo esta afecta al desarrollo del trazado y por tanto al contexto urbano. Se manifiestan determinadas carencias de tratamiento gráfico que facilitarían la comprensión histórica mediante el análisis de la forma y cómo esta ha ido variando sustancialmente. El concepto de escala y orientación reordena el estudio, no sólo de estos edificios protagonistas sino de los que se entretejen a su alrededor y componen el conjunto histórico, lo cual aporta nuevas conclusiones al estado de la cuestión que aquí compete. El principal objetivo de la tesis es, por tanto, contribuir a la dimensión patrimonial mediante el estudio de la arquitectura residencial del pueblo de El Pardo y en cómo esta ha ido conformando y consolidando el entramado urbano original en torno a edificios de la realeza y corte. Analizar aquellos edificios que perduran, los que fueron reconstruidos, rehabilitados, y apuntar acontecimientos históricos que formularon la actual fisonomía. Sistematizar y reordenar sobre la traza actual los edificios que desaparecieron, nos da las pistas sobre las modificaciones en concepto de escala arquitectónica y urbana. El estudio de las fuentes y establecer una metodología de conexión de estas, ayuda a detectar dónde no se han dirigido aún los focos de interés así como las lagunas que han quedado por explorar con el fin de responder a nuevas hipótesis, conceder conclusiones y abrir otras líneas de investigación. Como conclusiones generales, la tesis aporta documentación nueva sobre el objeto de estudio, no solicitada, digitalizada o publicada con anterioridad. En ella se analizan los procesos de configuración, consolidación y transformación en el Real Sitio mediante la sistematización de estados comparativos. Con respecto al estudio de los diferentes contextos natural y urbano la tesis analiza cómo los accidentes naturales, el desarrollo de infraestructuras y el impulso de la agronomía afectaron a El Pardo a partir del siglo XIX, y estudia los procesos de configuración, consolidación y transformación en el Real Sitio mediante la sistematización de la documentación encontrada de manera gráfica y escrita. En relación al marco patrimonial arquitectónico, la tesis analiza los procesos edificatorios históricos. Se estudian, a su vez, cambios de ocupación o uso que derivaron en reformas, ampliaciones, obras de nueva planta e incluso en derribos, así como los proyectos no materializados o que se llevaron a cabo de manera parcial. Con respecto al análisis del momento histórico, la tesis analiza las posibles afectaciones, políticas, sociales y económicas en las etapas de Monarquía, Segunda República, Guerra Civil y Posguerra. Por último, la tesis abre cuatro vías de investigación (que ya se han tratado y avanzado en parte pero que escapan a los límites de este trabajo) que pueden plantear nuevas hipótesis, reportando así respuestas sobre objetos de estudio complementarios y paralelos al presente. Estas refieren a análisis más concretos sobre El Palacio Real de El Pardo y la Casa de Oficios, el Camino Real de Madrid a El Pardo desde la Puerta de Hierro, los cuarteles, puertas y portilleras del Monte de El Pardo y los proyectos desarrollados por el arquitecto Diego Méndez en los Reales Sitios para el Patrimonio Nacional. ABSTRACT Following the Royal Site denomination being granted in the mid-18th Century, during the reign of Ferdinand VI, his successor Charles III proceeded to include all the Forests and Woodlands of El Pardo in his heritage. That then gave rise to the process of town planning and architectural construction that was completed around 1800. Thereafter, not only the process of conservation and consolidation of the main buildings has been maintained, but new civil engineering works have also been carried out. Some buildings changed ownership and use until, after the Civil War, the greatest transformation experienced by the Royal Site was undertaken. The time frame this paper concerns (1885 to 1965), has not attracted sufficient attention in studies of El Pardo due to there having been no new works with heritage status, nor has there been an analysis of the layout and external appearance of the residential centre in the town once conceived by Charles III. However, it is considered relevant to analyse the changes in residential activity, firstly, because it coexists with the official architecture and, thus, it is considered necessary to perform a global analysis of the complex and, secondly, because it facilitates a historical understanding of the original appearance of the complex at the end of the 18th Century. This time framework defines three main parts of the study that provide the structure of this thesis, the dates of which establish the key historical time frames: Actions in the consolidated town centre (1885-1931). Cessation of construction works (1931-1939). Proposals of regeneration and accelerated growth (1939-1965). Two distinct sub-chapters are also established within these, in order to explain the events that marked the transcendental changes in the history of El Pardo. When studying the subject matter, it is noted that in El Pardo, as is the case in other Royal Sites, outstanding buildings such as the Palace, the Prince's Cottage, the Trades House and the Infantes House are usually researched strictly from the point of view of their history, but not from an architectural perspective, nor analysing how that affects the development of the site layout and thus the urban area. Specific shortcomings are evident in the graphic treatment that would have otherwise facilitated a historical understanding through the analysis of the shape and the way it has gradually undergone substantial variation. The concept of scale and orientation reorganises the study, not only of these key buildings, but also of those that are woven around them and make up the historic complex, allowing entirely new conclusions concerning the subject matter analysed herein. Therefore, the main purpose of this thesis is to outline our heritage through the study of the residential architecture of the town of El Pardo and the analysis of the way the original town has been built up and consolidated around the buildings erected by royalty and the court; to analyse the buildings that still remain, those that were rebuilt, refurbished, and to note historic events that shaped its current appearance. To this end, a systematic classification and reorganisation on the current urban layout of the buildings that have disappeared will give us the key to understand changes in the concept of architectural and urban scale. Studying the sources and establishing a methodology to connect them will help us detect those areas where the focus of interest has not concentrated yet, and will also reveal the gaps that remain unexplored, in order to respond to new hypotheses, reach new conclusions and open up new lines of research. As general conclusions, this thesis provides new documentation on the subject matter that had not been requested, digitized or published before. There we find an analysis of the processes of configuration, consolidation and transformation of the Royal Site through a systematic classification of comparative states. With regard to the study of the multiple natural and urban environments, this thesis analyses the way natural features, development of infrastructures and agricultural driving forces affected El Pardo as of the 19th Century, and it studies the processes of configuration, consolidation and transformation of the Royal Site by systematically classifying the documentation found in graphic and written documents. In relation to the architectural heritage framework, this thesis analyses historical building processes. Likewise, a study is also performed on the changes in land occupation or use that led to reforms, extensions, new buildings and even to demolitions, as well as on unrealized projects, or even on those that were partially implemented. As for the analysis of the historical time period, this thesis assesses the potential political, social and economic effects of the Monarchy, Second Republic, Civil War and Post-War Periods. Finally, this thesis opens up four lines of investigation (that have already been discussed and partially advanced, but which fall beyond the scope of this work) that could pose new hypotheses, thus giving answer to other subject matters parallel and complementary to the one assessed herein. These refer to more specific analyses of El Palacio Real de El Pardo (Royal Palace of El Pardo) and the Casa de Oficios (Trades House), the Royal Highway from Madrid to El Pardo from Puerta de Hierro, the barracks, gates and entrances to estates in the Woodlands of El Pardo and the projects developed on the Royal Sites by the architect Diego Méndez for the National Heritage.

Guidance for the development of accessibility evaluation tools following the Unified Software Development Process

Automated and semi-automated accessibility evaluation tools are key to streamline the process of accessibility assessment, and ultimately ensure that software products, contents, and services meet accessibility requirements. Different evaluation tools may better fit different needs and concerns, accounting for a variety of corporate and external policies, content types, invocation methods, deployment contexts, exploitation models, intended audiences and goals; and the specific overall process where they are introduced. This has led to the proliferation of many evaluation tools tailored to specific contexts. However, tool creators, who may be not familiar with the realm of accessibility and may be part of a larger project, lack any systematic guidance when facing the implementation of accessibility evaluation functionalities. Herein we present a systematic approach to the development of accessibility evaluation tools, leveraging the different artifacts and activities of a standardized development process model (the Unified Software Development Process), and providing templates of these artifacts tailored to accessibility evaluation tools. The work presented specially considers the work in progress in this area by the W3C/WAI Evaluation and Report Working Group (ERT WG)

Evaluation of Development Projects: a Process-Centered Approach in the Outskirts of Lima, Peru.

Development cooperation projects work with people involved in processes of change and social transformation. While the main objective of the intervention is the development process itself, the project?s quality will be determined by the way of implementing it. Its success lies in the sustainability of the generated processes and the connection with them by the involved actors. The evaluation analyses both aspects. This article examines the evaluation, under a process approach, of a project on urban agriculture in Lima (Peru). The results show that the use of this approach, which combines different evaluation tools, allows the identification and analysis of the processes with the involved members, providing a better understanding of the real sustainability of the results.

A formalism and method for representing and reasoning with process models authored by subject matter experts

Enabling Subject Matter Experts (SMEs) to formulate knowledge without the intervention of Knowledge Engineers (KEs) requires providing SMEs with methods and tools that abstract the underlying knowledge representation and allow them to focus on modeling activities. Bridging the gap between SME-authored models and their representation is challenging, especially in the case of complex knowledge types like processes, where aspects like frame management, data, and control flow need to be addressed. In this paper, we describe how SME-authored process models can be provided with an operational semantics and grounded in a knowledge representation language like F-logic in order to support process-related reasoning. The main results of this work include a formalism for process representation and a mechanism for automatically translating process diagrams into executable code following such formalism. From all the process models authored by SMEs during evaluation 82% were well-formed, all of which executed correctly. Additionally, the two optimizations applied to the code generation mechanism produced a performance improvement at reasoning time of 25% and 30% with respect to the base case, respectively.

New concepts and techniques for the development of high-efficiency concentrating photovoltaic modules

El interés por los sistemas fotovoltaicos de concentración (CPV) ha resurgido en los últimos años amparado por el desarrollo de células multiunión de muy alta eficiencia basadas en semiconductores de los grupos III-V. Estas células han permitido obtener módulos de concentración con eficiencias que prácticamente duplican las del panel plano y que llegan al 35% en los módulos récord. Esta tesis está dedicada al diseño y la implementación experimental de nuevos conceptos que permitan obtener módulos CPV que no sólo alcancen una eficiencia alta en condiciones estándar sino que, además, sean lo suficientemente tolerantes a errores de montaje, seguimiento, temperatura y variaciones espectrales para que la energía que producen a lo largo del año sea máxima. Una de las primeras cuestiones que se abordan es el diseño de elementos ópticos secundarios para sistemas cuyo primario es una lente de Fresnel y que permiten, para una concentración fija, aumentar el ángulo de aceptancia y la tolerancia del sistema. Varios secundarios reflexivos y refractivos han sido diseñados y analizados mediante trazado de rayos. En particular, utilizando óptica anidólica y basándose en el diseño de una sola etapa conocido como ‘concentrador dieléctrico que funciona por reflexión total interna‘, se ha diseñado, fabricado y caracterizado un secundario con salida cuadrada que, usado junto con una lente de Fresnel, permite alcanzar simultáneamente una elevada eficiencia, concentración y aceptancia. Además, se ha propuesto y prototipado un método alternativo de fabricación para otro de los secundarios, denominado domo, consistente en el sobremoldeo de silicona sobre células solares. Una de las características que impregna todo el trabajo realizado en esta tesis es la aproximación holística en el diseño de módulos CPV, es decir, se ha prestado especial atención al diseño conjunto de la célula y la óptica para garantizar que el sistema total alcance la mayor eficiencia posible. En este sentido muchos sistemas ópticos desarrollados en esta tesis han sido diseñados, caracterizados y optimizados teniendo en cuenta que el ajuste de corriente entre las distintas subcélulas que comprenden la célula multiunión bajo el concentrador sea muy próximo a uno. La capa antirreflectante sobre la célula funciona, en cierto modo, como interfaz entre la óptica y la célula, por lo que se ha diseñado un método de optimización de capas antirreflectantes que considera no sólo el amplio rango de longitudes de onda para el que las células multiunión son sensibles sino también la distribución angular de intensidad sobre la célula creada por la óptica de concentración. Además, la cuestión de la falta de uniformidad también se ha abordado mediante la comparación de las distribuciones espectrales y espaciales de irradiancia que crean diferentes ópticas (simuladas mediante trazado de rayos y fotografiadas) y las pérdidas de eficiencia que experimentan las células iluminadas por dichas ópticas de concentración medidas experimentalmente. El efecto de la temperatura en la óptica de concentración también ha sido objeto de estudio de esta tesis. En particular, mediante simulaciones de elementos finitos se han dado los primeros pasos para el análisis de las deformaciones que sufren los dientes de las lentes de Fresnel híbridas (vidrio-silicona), así como el cambio de índice de refracción con la temperatura y la influencia de ambos efectos sobre el funcionamiento de los sistemas. Se ha implementado un modelo que tiene por objeto considerar las variaciones ambientales, principalmente temperatura y contenido espectral de la radiación directa, así como las sensibilidades térmica y espectral de los sistemas CPV, con el fin de maximizar la energía producida por un módulo de concentración a lo largo de un año en un emplazamiento determinado. Los capítulos 5 y 6 de este libro están dedicados al diseño, fabricación y caracterización de un nuevo concepto de módulo fotovoltaico denominado FluidReflex y basado en una única etapa reflexiva con dieléctrico fluido. En este nuevo concepto la presencia del fluido aporta algunas ventajas significativas como son: un aumento del producto concentración por aceptancia (CAP, en sus siglas en inglés) alcanzable al rodear la célula con un medio cuyo índice de refracción es mayor que uno, una mejora de la eficiencia óptica al disminuir las pérdidas por reflexión de Fresnel en varias interfaces, una mejora de la disipación térmica ya que el calor que se concentra junto a la célula se trasmite por convección natural y conducción en el fluido y un aislamiento eléctrico mejorado. Mediante la construcción y medida de varios prototipos de unidad elemental se ha demostrado que no existe ninguna razón fundamental que impida la implementación práctica del concepto teórico alcanzando una elevada eficiencia. Se ha realizado un análisis de fluidos candidatos probando la existencia de al menos dos de ellos que cumplen todos los requisitos (en particular el de estabilidad bajo condiciones de luz concentrada) para formar parte del sistema de concentración FluidReflex. Por ´ultimo, se han diseñado, fabricado y caracterizado varios prototipos preindustriales de módulos FluidReflex para lo cual ha sido necesario optimizar el proceso de fabricación de la óptica multicavidad a fin de mantener el buen comportamiento óptico obtenido en la fabricación de la unidad elemental. Los distintos prototipos han sido medidos, tanto en el laboratorio como bajo el sol real, analizando el ajuste de corriente de la célula iluminada por el concentrador FluidReflex bajo diferentes distribuciones espectrales de la radiación incidente así como el excelente comportamiento térmico del módulo. ABSTRACT A renewed interest in concentrating photovoltaic (CPV) systems has emerged in recent years encouraged by the development of high-efficiency multijunction solar cells based in IIIV semiconductors that have led to CPV module efficiencies which practically double that of flat panel PV and which reach 35% for record modules. This thesis is devoted to the design and experimental implementation of new concepts for obtaining CPV modules that not only achieve high efficiency under standard conditions but also have such a wide tolerance to assembly errors, tracking, temperature and spectral variations, that the energy generated by them throughout the year is maximized. One of the first addressed issues is the design of secondary optical elements whose primary optics is a Fresnel lens and which, for a fixed concentration, allow an increased acceptance angle and tolerance of the system. Several reflective and refractive secondaries have been designed and analyzed using ray tracing. In particular, using nonimaging optics and based on the single-stage design known as ‘dielectric totally internally reflecting concentrator’, a secondary with square output has been designed, fabricated and characterized. Used together with a Fresnel lens, the secondary can simultaneously achieve high efficiency, concentration and acceptance. Furthermore, an alternative method has been proposed and prototyped for the fabrication of the secondary named dome. The optics is manufactured by direct overmolding of silicone over the solar cells. One characteristic that permeates all the work done in this thesis is the holistic approach in the design of CPV modules, meaning that special attention has been paid to the joint design of the solar cell and the optics to ensure that the total system achieves the highest attainable efficiency. In this regard, many optical systems developed in the thesis have been designed, characterized and optimized considering that the current matching among the subcells within the multijunction solar cell beneath the optics must be close to one. Antireflective coating over the cell acts, somehow, as an interface between the optics and the cell. Consequently, a method has been designed to optimize antireflective coatings that takes into account not only the broad wavelength range that multijunction solar cells are sensitive to but also the angular intensity distribution created by the concentrating optics. In addition, the issue of non-uniformity has also been addressed by comparing the spectral and spatial distributions of irradiance created by different optics (simulated by ray tracing and photographed) and the efficiency losses experienced by cells illuminated by those concentrating optics experimentally determined. The effect of temperature on the concentrating optics has also been studied in this thesis. In particular, finite element simulations have been use to analyze the deformations experienced by the facets of hybrid (silicon-glass) Fresnel lenses, the change of refractive index with temperature and the influence of both effects on the system performance. A model has been implemented which take into consideration atmospheric variations, mainly temperature and spectral content of the direct normal irradiance, as well as thermal and spectral sensitivities of systems, with the aim of maximizing the energy harvested by a CPV module throughout the year in a particular location. Chapters 5 and 6 of this book are devoted to the design, fabrication, and characterization of a new concentrator concept named FluidReflex and based on a single-stage reflective optics with fluid dielectric. In this new concept, the presence of the fluid provides some significant advantages such as: an increased concentration acceptance angle product (CAP) achievable by surrounding the cell with a medium whose refractive index is greater than one, an improvement of the optical efficiency by reducing losses due to Fresnel reflection at several interfaces, an improvement in heat dissipation as the heat concentrated near the cell is transmitted by natural convection and conduction in the fluid, and an improved electrical insulation. By fabricating and characterizing several elementary-unit prototypes it was shown that there is no fundamental reason that prevents the practical implementation of this theoretical concept reaching high efficiency. Several fluid candidates were investigated proving the existence of at least to fluids that meet all the requirements (including the stability under concentrated light) to become part of the FluidReflex concentrator. Finally, several pre-industrial FluidReflex module prototypes have been designed and fabricated. An optimization process for the manufacturing of the multicavity optics was necessary to attain such an optics quality as the one achieved by the single unit. The module prototypes have been measured, both indoors and outdoors, analyzing the current matching of the solar cells beneath the concentrator for different spectral distribution of the incident irradiance. Additionally, the module showed an excellent thermal performance.

A Semantic-Based Approach to Attain Reproducibility of Computational Environments in Scientic Work ows: A Case Study

Reproducible research in scientic work ows is often addressed by tracking the provenance of the produced results. While this approach allows inspecting intermediate and nal results, improves understanding, and permits replaying a work ow execution, it does not ensure that the computational environment is available for subsequent executions to reproduce the experiment. In this work, we propose describing the resources involved in the execution of an experiment using a set of semantic vocabularies, so as to conserve the computational environment. We dene a process for documenting the work ow application, management system, and their dependencies based on 4 domain ontologies. We then conduct an experimental evaluation sing a real work ow application on an academic and a public Cloud platform. Results show that our approach can reproduce an equivalent execution environment of a predened virtual machine image on both computing platforms.

CAS: A tool for improving autonomous work

The EHEA proposes a student-centered teaching model. Therefore, it seems necessary to actively involve the students in the teaching-learning process. Increasing the active participation of the students is not always easy in mathematical topics, since, when the students just enter the University, their ability to carry out autonomous mathematical work is scarce. In this paper we present some experiences related with the use of Computer Algebra Systems (CAS). All the experiences are designed in order to develop some mathematical competencies and mainly self-learning, the use of technology and team-work. The experiences include some teachers? proposals including: small projects to be executed in small groups, participation in competitions, the design of different CAS-Toolboxes, etc. The results obtained in the experiences, carried out with different groups of students from different engineering studies at different universities, makes us slightly optimistic about the educational value of the model.

Understanding and improving the chemical vapor deposition process for solar grade silicon production

Esta Tesis Doctoral se centra en la investigación del proceso de producción de polisilicio para aplicaciones fotovoltaicas (FV) por la vía química; mediante procesos de depósito en fase vapor (CVD). El polisilicio para la industria FV recibe el nombre de silicio de grado solar (SoG Si). Por un lado, el proceso que domina hoy en día la producción de SoG Si está basado en la síntesis, destilación y descomposición de triclorosilano (TCS) en un reactor CVD -denominado reactor Siemens-. El material obtenido mediante este proceso es de muy alta pureza, pero a costa de un elevado consumo energético. Así, para alcanzar los dos principales objetivos de la industria FV basada en silicio, bajos costes de producción y bajo tiempo de retorno de la energía invertida en su fabricación, es esencial disminuir el consumo energético de los reactores Siemens. Por otro lado, una alternativa al proceso Siemens considera la descomposición de monosilano (MS) en un reactor de lecho fluidizado (FBR). Este proceso alternativo tiene un consumo energético mucho menor que el de un reactor Siemens, si bien la calidad del material resultante es también menor; pero ésta puede ser suficiente para la industria FV. A día de hoy los FBR deben aún abordar una serie de retos para que su menor consumo energético sea una ventaja suficiente comparada con otras desventajas de estos reactores. En resumen, la investigación desarrollada se centra en el proceso de depósito de polysilicio por CVD a partir de TCS -reactor Siemens-; pero también se investiga el proceso de producción de SoG Si en los FBR exponiendo las fortalezas y debilidades de esta alternativa. Para poder profundizar en el conocimiento del proceso CVD para la producción de polisilicio es clave el conocimiento de las reacciones químicas fundamentales y cómo éstas influencian la calidad del producto resultante, al mismo tiempo que comprender los fenómenos responsables del consumo energético. Por medio de un reactor Siemens de laboratorio en el que se llevan a cabo un elevado número de experimentos de depósito de polisilicio de forma satisfactoria se adquiere el conocimiento previamente descrito. Se pone de manifiesto la complejidad de los reactores CVD y de los problemas asociados a la pérdidas de calor de estos procesos. Se identifican las contribuciones a las pérdidas de calor de los reactores CVD, éstas pérdidas de calor son debidas principalmente a los fenómenos de radiación y, conducción y convección vía gases. En el caso de los reactores Siemens el fenómeno que contribuye en mayor medida al alto consumo energético son las pérdidas de calor por radiación, mientras que en los FBRs tanto la radiación como el calor transferido por transporte másico contribuyen de forma importante. Se desarrolla un modelo teórico integral para el cálculo de las pérdidas de calor en reactores Siemens. Este modelo está formado a su vez por un modelo para la evaluación de las pérdidas de calor por radiación y modelos para la evaluación de las pérdidas de calor por conducción y convección vía gases. Se ponen de manifiesto una serie de limitaciones del modelo de pérdidas de calor por radiación, y se desarrollan una serie de modificaciones que mejoran el modelo previo. El modelo integral se valida por medio un reactor Siemens de laboratorio, y una vez validado se presenta su extrapolación a la escala industrial. El proceso de conversión de TCS y MS a polisilicio se investiga mediante modelos de fluidodinámica computacional (CFD). Se desarrollan modelados CFD para un reactor Siemens de laboratorio y para un prototipo FBR. Los resultados obtenidos mediante simulación son comparados, en ambos casos, con resultados experimentales. Los modelos desarrollados se convierten en herramientas para la identificación de aquellos parámetros que tienen mayor influencia en los procesos CVD. En el caso del reactor Siemens, ambos modelos -el modelo integral y el modelado CFD permiten el estudio de los parámetros que afectan en mayor medida al elevado consumo energético, y mediante su análisis se sugieren modificaciones para este tipo de reactores que se traducirían en un menor número de kilovatios-hora consumidos por kilogramo de silicio producido. Para el caso del FBR, el modelado CFD permite analizar el efecto de una serie de parámetros sobre la distribución de temperaturas en el lecho fluidizado; y dicha distribución de temperaturas está directamente relacionada con los principales retos de este tipo de reactores. Por último, existen nuevos conceptos de depósito de polisilicio; éstos se aprovechan de la ventaja teórica de un mayor volumen depositado por unidad de tiempo -cuando una mayor superficie de depósito está disponible- con el objetivo de reducir la energía consumida por los reactores Siemens. Estos conceptos se exploran mediante cálculos teóricos y pruebas en el reactor Siemens de laboratorio. ABSTRACT This Doctoral Thesis comprises research on polysilicon production for photovoltaic (PV) applications through the chemical route: chemical vapor deposition (CVD) process. PV polysilicon is named solar grade silicon (SoG Si). On the one hand, the besetting CVD process for SoG Si production is based on the synthesis, distillation, and decomposition of thriclorosilane (TCS) in the so called Siemens reactor; high purity silicon is obtained at the expense of high energy consumption. Thus, lowering the energy consumption of the Siemens process is essential to achieve the two wider objectives for silicon-based PV technology: low production cost and low energy payback time. On the other hand, a valuable variation of this process considers the use of monosilane (MS) in a fluidized bed reactor (FBR); lower output material quality is obtained but it may fulfil the requirements for the PV industry. FBRs demand lower energy consumption than Siemens reactors but further research is necessary to address the actual challenges of these reactors. In short, this work is centered in polysilicon CVD process from TCS -Siemens reactor-; but it also offers insights on the strengths and weaknesses of the FBR for SoG Si production. In order to aid further development in polysilicon CVD is key the understanding of the fundamental reactions and how they influence the product quality, at the same time as to comprehend the phenomena responsible for the energy consumption. Experiments conducted in a laboratory Siemens reactor prove the satisfactory operation of the prototype reactor, and allow to acquire the knowledge that has been described. Complexity of the CVD reactors is stated and the heat loss problem associated with polysilicon CVD is addressed. All contributions to the energy consumption of Siemens reactors and FBRs are put forward; these phenomena are radiation and, conduction and convection via gases heat loss. In a Siemens reactor the major contributor to the energy consumption is radiation heat loss; in case of FBRs radiation and heat transfer due to mass transport are both important contributors. Theoretical models for radiation, conduction and convection heat loss in a Siemens reactor are developed; shaping a comprehensive theoretical model for heat loss in Siemens reactors. Limitations of the radiation heat loss model are put forward, and a novel contribution to the existing model is developed. The comprehensive model for heat loss is validated through a laboratory Siemens reactor, and results are scaled to industrial reactors. The process of conversion of TCS and MS gases to solid polysilicon is investigated by means of computational fluid-dynamics models. CFD models for a laboratory Siemens reactor and a FBR prototype are developed. Simulated results for both CVD prototypes are compared with experimental data. The developed models are used as a tool to investigate the parameters that more strongly influence both processes. For the Siemens reactors, both, the comprehensive theoretical model and the CFD model allow to identify the parameters responsible for the great power consumption, and thus, suggest some modifications that could decrease the ratio kilowatts-hour per kilogram of silicon produced. For the FBR, the CFD model allows to explore the effect of a number of parameters on the thermal distribution of the fluidized bed; that is the main actual challenge of these type of reactors. Finally, there exist new deposition surface concepts that take advantage of higher volume deposited per time unit -when higher deposition area is available- trying to reduce the high energy consumption of the Siemens reactors. These novel concepts are explored by means of theoretical calculations and tests in the laboratory Siemens prototype.

Selection, training and validation process of a sensory panel for bread analysis: Influence of cultivar on the quality of breads made from common wheat and spelta wheat

A protocol of selection, training and validation of the members of the panel for bread sensory analysis is proposed to assess the influence of wheat cultivar on the sensory quality of bread. Three cultivars of bread wheat and two cultivars of spelt wheat organically-grown under the same edaphoclimatic conditions were milled and baked using the same milling and baking procedure. Through the use of triangle tests, differences were identified between the five breads. Significant differences were found between the spelt breads and those made with bread wheat for the attributes ?crumb cell homogeneity? and ?crumb elasticity?. Significant differences were also found for the odor and flavor attributes, with the bread made with ?Espelta Navarra? being the most complex, from a sensory point of view. Based on the results of this study, we propose that sensory properties should be considered as breeding criteria for future work on genetic improvement.