Jet energy measurement and its systematic uncertainty in proton-proton collisions at s√=7 TeV with the ATLAS detector

The jet energy scale (JES) and its systematic uncertainty are determined for jets measured with the ATLAS detector using proton–proton collision data with a centre-of-mass energy of s√=7 TeV corresponding to an integrated luminosity of 4.7 fb −1 . Jets are reconstructed from energy deposits forming topological clusters of calorimeter cells using the anti- kt algorithm with distance parameters R=0.4 or R=0.6 , and are calibrated using MC simulations. A residual JES correction is applied to account for differences between data and MC simulations. This correction and its systematic uncertainty are estimated using a combination of in situ techniques exploiting the transverse momentum balance between a jet and a reference object such as a photon or a Z boson, for 20≤pjetT<1000 GeV and pseudorapidities |η|<4.5 . The effect of multiple proton–proton interactions is corrected for, and an uncertainty is evaluated using in situ techniques. The smallest JES uncertainty of less than 1 % is found in the central calorimeter region ( |η|<1.2 ) for jets with 55≤pjetT<500 GeV . For central jets at lower pT , the uncertainty is about 3 %. A consistent JES estimate is found using measurements of the calorimeter response of single hadrons in proton–proton collisions and test-beam data, which also provide the estimate for pjetT>1 TeV. The calibration of forward jets is derived from dijet pT balance measurements. The resulting uncertainty reaches its largest value of 6 % for low- pT jets at |η|=4.5 . Additional JES uncertainties due to specific event topologies, such as close-by jets or selections of event samples with an enhanced content of jets originating from light quarks or gluons, are also discussed. The magnitude of these uncertainties depends on the event sample used in a given physics analysis, but typically amounts to 0.5–3 %.

Degradation of all-inkjet-printed organic thin-film transistors with TIPS-pentacene under processes applied in textile manufacturing

Printed electronics represent an alternative solution for the manufacturing of low-temperature and large area flexible electronics. The use of inkjet printing is showing major advantages when compared to other established printing technologies such as, gravure, screen or offset printing, allowing the reduction of manufacturing costs due to its efficient material usage and the direct-writing approach without requirement of any masks. However, several technological restrictions for printed electronics can hinder its application potential, e.g. the device stability under atmospheric or even more stringent conditions. Here, we study the influence of specific mechanical, chemical, and temperature treatments usually appearing in manufacturing processes for textiles on the electrical performance of all-inkjet-printed organic thin-film transistors (OTFTs). Therefore, OTFTs where manufactured with silver electrodes, a UV curable dielectric, and 6,13-bis(triisopropylsilylethynyl) pentance (TIPS-pentacene) as the active semiconductor layer. All the layers were deposited using inkjet printing. After electrical characterization of the printed OTFTs, a simple encapsulation method was applied followed by the degradation study allowing a comparison of the electrical performance of treated and not treated OTFTs. Industrial calendering, dyeing, washing and stentering were selected as typical textile processes and treatment methods for the printed OTFTs. It is shown that the all-inkjet-printed OTFTs fabricated in this work are functional after their submission to the textiles processes but with degradation in the electrical performance, exhibiting higher degradation in the OTFTs with shorter channel lengths (L=10 μm).

Spatio-temporal modelling of environmental data

Programa Doutoral em Matemática e Aplicações.

Assessment and management of the geomorphological heritage of Monte Pindo (NW Spain): a landscape as a symbol of identity

This study focuses on the granite mountain known as Monte Pindo (627 m above sea level) in the Autonomous Community of Galicia (NW Spain). This territory is included in the area classified as “Costa da Morte” in the “Politica de Ordenación Litoral” (POL) (Coastal Planning Policy) for the region of Galicia. This coastal unit, located between “Rías Baixas” and “Cape Fisterra” has great potential for demonstrating geological processes and its geomorphological heritage is characterized by a high degree of geodiversity of granite landforms. The main objective of our work is to assess the geomorphological heritage of the site, thus revealing its wide geodiversity. We shall analyze and highlight: its scientific value, developing an inventory of granite landforms; its educational valuel and its geotouristic potential. It must be ensured that the Administration understands that natural diversity is composed of both geodiversity and biodiversity. Only then will the sustainable management of Monte Pindo become possible by integrating natural and cultural heritage values. The goal is to ensure that Monte Pindo and its immediate surroundings become a geopark with the aim of promoting local development projects based on the conservation and valorization of its geological heritage.

Attachment, infidelity, and loneliness in college students involved in a romantic relationship: the role of relationship satisfaction, morbidity and prayer for partner

This study examined the mediating effects of relationship satisfaction, prayer for a partner, and morbidity in the relationship between attachment and loneliness, infidelity and loneliness, and psychological morbidity and loneliness, in college students involved in a romantic relationship. Participants were students in an introductory course on family development. This study examined only students (n = 345) who were involved in a romantic relationship. The average age of participants was 19.46 (SD = 1.92) and 25 % were males. Short-form UCLA Loneliness Scale (ULS-8), (Hays and DiMatteo in J Pers Assess 51:69–81, doi:10.1207/s15327752jpa5101_6, 1987); Relationship Satisfaction Scale (Funk and Rogge in J Fam Psychol 21:572–583, doi:10.1037/0893-3200.21.4.572, 2007); Rotterdam Symptom Checklist (De Haes et al. in Measuring the quality of life of cancer patients with the Rotterdam Symptom Checklist (RSCL): a manual, Northern Centre for Healthcare Research, Groningen, 1996); Prayer for Partner Scale, (Fincham et al. in J Pers Soc Psychol 99:649–659, doi:10.1037/a0019628, 2010); Infidelity Scale, (Drigotas et al. in J Pers Soc Psychol 77:509–524, doi:10.1037/0022-3514.77.3.509, 1999); and the Experiences in Close Relationship Scale-short form (Wei et al. in J Couns Psychol 52(4):602–614, doi:10.1037/0022-0167.52.4.602, 2005). Results showed that relationship satisfaction mediated the relationship between avoidance attachment and loneliness and between infidelity and loneliness. Physical morbidity mediated the relationship between anxious attachment and psychological morbidity. Psychological morbidity mediated the relationship between anxious attachment and physical morbidity. The present results expand the literature on attachment by presenting evidence that anxious and avoidant partners experience loneliness differently. Implications for couple’s therapy are addressed. Future research should replicate these results with older samples and married couples.

Sustentabilidade no Design: uma abordagem aos resíduos limpos das indústrias do calçado

Dissertação de mestrado em Design e Marketing

Development of a methodology to incorporate risk and uncertainty in electricity power planning

Dissertação de mestrado em Engenharia Industrial

Intermetallic layer formation and influence in solder joints reliability

Dissertação de mestrado integrado em Materials Engineering

Effect of hormonal changes on corneal biomechanical properties and anterior segment ocular perameters

Dissertação de mestrado em Optometria Avançada

Screening for depression and anxiety disorders from pregnancy to postpartum with the EPDS and STAI

The Edinburgh Postnatal Depression Scale (EPDS) and the State Anxiety Inventory (STAI-S) are widely used self-report measures that still need to be further validated for the perinatal period. The aim of this study was to examine the screening performance of the EPDS and the STAI-S in detecting depressive and anxiety disorders at pregnancy and postpartum. Women screening positive on EPDS (EPDS ≥ 9) or STAI-S (STAI-S ≥ 45) during pregnancy (n = 90), as well as matched controls (n = 58) were selected from a larger study. At 3 months postpartum, 99 of these women were reassessed. At a second stage, women were administered a clinical interview to establish a DSM-IV-TR diagnosis. Receiver operator characteristics (ROC) analysis yielded areas under the curve higher than .80 and .70 for EPDS and STAI-S, respectively. EPDS and STAI-S optimal cut-offs were found to be lower at postpartum (EDPS = 7; STAI-S = 34) than during pregnancy (EPDS = 9; STAI-S = 40). EPDS and STAI-S are reasonably valid screening tools during pregnancy and the postpartum.

Mother’s anxiety and depression and associated risk factors during early pregnancy: effects on fetal growth and activity at 20–22 weeks of gestation

To examine effects of mother's anxiety and depression and associated risk factors during early pregnancy on fetal growth and activity. Repeated measures of mother's anxiety (State-Anxiety Inventory (STAI-S)) and depression (Edinburgh Postnatal Depression Scale (EPDS)) and related socio demographics and substance consumption were obtained at the 1st and 2nd pregnancy trimesters, and fetus' (N = 147) biometric data and behavior was recorded during ultrasound examination at 20-22 weeks of gestation. Higher anxiety symptoms were associated to both lower fetal growth and higher fetal activity. While lower education, primiparity, adolescent motherhood, and tobacco consumption predicted lower fetal growth, coffee intake predicted lower fetal activity. Vulnerability of fetal development to mother's psychological symptoms as well as to other sociodemographic and substance consumption risk factors during early and mid pregnancy is suggested.

Mother's anxiety and depression during the third pregnancy trimester and neonate's mother versus stranger's face/voice visual preference

Background: Neonates show visual preference for their mother's face/voice and shift their attention from their mother to a stranger's face/voice after habituation. Aim: To assess neonate's mother versus stranger's face/voice visual preference, namely mother's anxiety and depression during the third pregnancy trimester and neonate's: 1) visual preference for the mother versus the stranger's face/voice (pretest visual preference), 2) habituation to the mother's face/voice and 3) visual preference for the stranger versus the mother's face/voice (posttest visual preference). Method: Mothers (N=100) filled out the Edinburgh Postnatal Depression Scale (EPDS) and the State Anxiety Inventory (STAI) both at the third pregnancy trimester and childbirth, and the “preference and habituation to the mother's face/voice versus stranger” paradigm was administered to their newborn 1 to 5 days after childbirth. Results: Neonates of anxious/depressed mothers during the third pregnancy trimester contrarily to neonates of non-anxious/non-depressed mothers did not look 1) longer at their mother's than at the stranger's face/voice at the pretest visual preference (showing no visual preference for the mother), nor 2) longer at the stranger's face/voice in the posttest than in the pretest visual preference (not improving their attention to the stranger's after habituation). Conclusion: Infants exposed to mother's anxiety/depression at the third gestational trimester exhibit less perceptual/social competencies at birth.

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

Procesos oxidativos en matrices alimentarias complejas. Oxidative processes in complex food matrices.

Las reacciones bioquímicas que ocurren como consecuencia del tratamiento y almacenamiento de los alimentos, mejoran la seguridad alimentaria, las propiedades sensoriales y la vida útil. Sin embargo, el tratamiento térmico, la exposición a la luz y el oxígeno pueden causar daño oxidativo a los lípidos y proteínas. Los procesos oxidativos de matrices complejas tienen características distintivas que no se manifiestan cuando los componentes son sometidos a oxidación individualmente. La hipótesis de trabajo es que la oxidación de proteínas en matrices alimentarias complejas altera la estructura y las propiedades funcionales de las proteínas y, que las modificaciones que se producen varían según las condiciones de procesamiento y de la composición química del alimento. Nuestros estudios intentan demostrar que el estado oxidativo de las proteínas de un alimento es un parámetro importante para la evaluación de las propiedades funcionales, sensoriales y nutricionales de un producto lácteo. El objetivo general del proyecto es el estudio de los procesos de oxidación de matrices alimentarias complejas (la leche, miel) y su relación con distintos procesos y materiales utilizados en la industria. Es decir, nos proponemos estudiar las consecuencias funcionales y biológicas (calidad nutricional, coagulación) de la oxidación proteica en modelos experimentales “in vitro” y en productos comerciales. 1. Estudiar los fenómenos de peroxidación proteica en leche entera y descremada sometida a los distintos procesos tecnológicos de la producción de leche y queso a escala laboratorio. Se realizarán las mismas experiencias con albúmina sérica y con proteínas aisladas de suero de leche para comparar diferencias entre una matriz compleja y una simple. 2. Determinar la relación entre oxidación y composición proteica de la leche, y los cambios en las fracciones proteicas aisladas (caseínas y beta-lactoglobulina). 3. Analizar el impacto de los procesos tecnológicos a nivel de producción primaria (composición proteica y estado de oxidación) en los indicadores de inflamación (contenido de células somáticas y proteína C Reactiva) y de estado redox (capacidad antioxidante de los productos lácteos y nivel de carbonilos de proteinas). 4. Comparar las características de composición química y el estado de oxidación de leche provenientes de las tres regiones (Buenos Aires, Santa Fe y Córdoba) que conforman la cuenca láctea Argentina. Este objetivo se realizará conjuntamente con los integrantes de nuestro grupo de investigación que trabajan en el Laboratorio de Control de Calidad de la Escuela Superior de Lechería. 5. Determinar los metabolitos secundarios de mieles uniflorales propuestos como responsables de la capacidad antioxidante de estas (polifenoles) y como indicadores de su origen botánico. 6. Valorar la capacidad antioxidante total de mieles uniflorales. 7. Validar los métodos analíticos y semicuantitativos utilizados y a utilizar en el presente proyecto teniendo en cuenta lo efectos de matrices típico de los fluidos biológicos y las mezclas. El estudio de las modificaciones oxidativas de matrices complejas es un tema que es importante tanto desde el punto de vista del conocimiento básico como del aplicado. Nosotros creemos que el presente proyecto aportará conocimiento sobre las características de las vías oxidativas de proteínas en matrices complejas y que podrá ser utilizado para diseñar estrategias productivas tendientes a disminuir el deterioro de la calidad de la leche debido a la exposición a energía radiante. Parte de la experiencia ganada por el grupo ha sido ya volcada a subsanar dificultades y problemas de oxidación y deterioro de la calidad de alimentos. Además, se contribuirá a discernir la paradoja que existe en el área sobre las propiedades oxidantes/antioxidantes de los polifenoles y la relación entre estas y el estado oxidativo de un alimento. The biochemical reactions that occur as a result of food treatment and storage, improve food security, sensory properties and shelf life. Heat treatment, exposure to light and oxygen can cause oxidative damage to lipids and proteins. Oxidative processes in complex matrices display distinctive features that do not appear when the components are individually subjected to oxidation. The hypothesis is that protein oxidation in complex food matrices alters the structure and functional properties of proteins and that the modifications vary according to process conditions and food composition. The main goal is to study oxidation of complex food matrices (milk, honey) with different processes and materials used in the industry. The specific aims are: 1. To study protein oxidation in whole milk and skim subject to various technological processes. The same experiences will be done with serum albumin and isolated whey proteins to compare complex and simple matrices. 2. To determine the relationship between oxidation and milk protein composition, and changes in casein and beta-lactoglobulin. 3. Analyze the impact of technological processes at the level of primary production on markers of inflammation and redox (antioxidant capacity and protein carbonyls). 4. Compare characteristics of chemical composition and oxidation state of milk. 5. Determine secondary metabolites of honey responsible for the antioxidant capacity of these. 6. To evaluate the total antioxidant capacity unifloral honey. This project will provide knowledge about characteristics of oxidative pathways of proteins in complex matrices that can be used to design production strategies aimed at reduce the deterioration of milk quality. Also, it would help to discern the paradox that exists on the oxidants/antioxidants properties of polyphenols and the relationship between these and the oxidative status of a food.

Cytochemical characterization of gill and hepatopancreatic cells of the crab Ucides cordatus (Crustacea, Brachyura) validated by cell metal transport

Ucides cordatus (Linnaeus, 1763) is a hypo-hyper-regulating mangrove crab possessing gills for respiratory and osmoregulatory processes, separated in anterior and posterior sections. They also have hepatopancreas, which is responsible for digestion and absorption of nutrients and detoxification of toxic metals. Each of these organs has specific cells that are important for in vitro studies in cell biology, ion and toxic metals transport. In order to study and characterize cells from gills and hepatopancreas, both were separated using a Sucrose Gradient (SG) from 10 to 40% and cells in each gradient were characterized using the vital mitochondrial dye DASPEI (2-(4-dimethylaminostyryl)-N- ethylpyridinium iodide) and Trichrome Mallory's stain. Both in 20 and 40% SG for gill cells and 30% SG for hepatopancreatic cells, a greater number of cells were colored with DASPEI, indicating a larger number of mitochondria in these cells. It is concluded that the gill cells present in 20% and 40% SG are Thin cells, responsible for respiratory processes and Ionocytes responsible for ion transport, respectively. For hepatopancreatic cells, the 30% SG is composed of Fibrillar cells that possess larger number of membrane ion and nutrient transporters. Moreover, the transport of toxic metal cadmium (Cd) by isolated hepatopancreatic cells was performed as a way of following cell physiological integrity after cell separation and to study differences in transport among the cells. All hepatopancreatic cells were able to transport Cd. These findings are the first step for further work on isolated cells of these important exchange epithelia of crabs, using a simple separation method and to further develop successful in vitro cell culture in crabs.