Pore structure and column efficiency of silica monoliths in high performance liquid chromatography (HPLC)

Five different methods were critically examined to characterize the pore structure of the silica monoliths. The mesopore characterization was performed using: a) the classical BJH method of nitrogen sorption data, which showed overestimated values in the mesopore distribution and was improved by using the NLDFT method, b) the ISEC method implementing the PPM and PNM models, which were especially developed for monolithic silicas, that contrary to the particulate supports, demonstrate the two inflection points in the ISEC curve, enabling the calculation of pore connectivity, a measure for the mass transfer kinetics in the mesopore network, c) the mercury porosimetry using a new recommended mercury contact angle values. rnThe results of the characterization of mesopores of monolithic silica columns by the three methods indicated that all methods were useful with respect to the pore size distribution by volume, but only the ISEC method with implemented PPM and PNM models gave the average pore size and distribution based on the number average and the pore connectivity values.rnThe characterization of the flow-through pore was performed by two different methods: a) the mercury porosimetry, which was used not only for average flow-through pore value estimation, but also the assessment of entrapment. It was found that the mass transfer from the flow-through pores to mesopores was not hindered in case of small sized flow-through pores with a narrow distribution, b) the liquid penetration where the average flow-through pore values were obtained via existing equations and improved by the additional methods developed according to Hagen-Poiseuille rules. The result was that not the flow-through pore size influences the column bock pressure, but the surface area to volume ratio of silica skeleton is most decisive. Thus the monolith with lowest ratio values will be the most permeable. rnThe flow-through pore characterization results obtained by mercury porosimetry and liquid permeability were compared with the ones from imaging and image analysis. All named methods enable a reliable characterization of the flow-through pore diameters for the monolithic silica columns, but special care should be taken about the chosen theoretical model.rnThe measured pore characterization parameters were then linked with the mass transfer properties of monolithic silica columns. As indicated by the ISEC results, no restrictions in mass transfer resistance were noticed in mesopores due to their high connectivity. The mercury porosimetry results also gave evidence that no restrictions occur for mass transfer from flow-through pores to mesopores in the small scaled silica monoliths with narrow distribution. rnThe prediction of the optimum regimes of the pore structural parameters for the given target parameters in HPLC separations was performed. It was found that a low mass transfer resistance in the mesopore volume is achieved when the nominal diameter of the number average size distribution of the mesopores is appr. an order of magnitude larger that the molecular radius of the analyte. The effective diffusion coefficient of an analyte molecule in the mesopore volume is strongly dependent on the value of the nominal pore diameter of the number averaged pore size distribution. The mesopore size has to be adapted to the molecular size of the analyte, in particular for peptides and proteins. rnThe study on flow-through pores of silica monoliths demonstrated that the surface to volume of the skeletons ratio and external porosity are decisive for the column efficiency. The latter is independent from the flow-through pore diameter. The flow-through pore characteristics by direct and indirect approaches were assessed and theoretical column efficiency curves were derived. The study showed that next to the surface to volume ratio, the total porosity and its distribution of the flow-through pores and mesopores have a substantial effect on the column plate number, especially as the extent of adsorption increases. The column efficiency is increasing with decreasing flow through pore diameter, decreasing with external porosity, and increasing with total porosity. Though this tendency has a limit due to heterogeneity of the studied monolithic samples. We found that the maximum efficiency of the studied monolithic research columns could be reached at a skeleton diameter of ~ 0.5 µm. Furthermore when the intention is to maximize the column efficiency, more homogeneous monoliths should be prepared.rn

Aussagekraft einer quantitativen, PC-unterstützten PCNA-Bestimmung an Leiomyosarkomen und Leiomyomen

Ziel der Studie war die Untersuchung inwieweit PCNA als immunhistochemisches Hilfsmittel eine Verbesserung der Abgrenzung von uterinen LM gegenüber uterinen LMS und eine Hilfe bei der Prognoseaussage bei uterinen und gastrointestinalen LMS darstellt. Dabei wurden auch weitere, herkömmliche, in einer Reihe von Studien untersuchte Prognoseparameter mit in Betracht gezogen.rnDie Auswertung der Färbungen erfolgte quantitativ mittels einer PC-gesteuerten Bildverarbeitung, die neben der positiven Zellfläche und Zellzahl auch die Kernfläche berechnet. Vorteil der quantitativen Messung ist die Möglichkeit der Reproduzierbarkeit unabhängig vom Benutzer, im Gegensatz zu semiquantitativen Analysen, die häufiger angewendet werden.rnEs fällt dabei auf, dass sowohl die Zellkerngröße generell als auch die Zellkerngröße der positiv gefärbten Zellen signifikant größer bei LMS als bei LM ist. (p< 0,0001). Zwischen den Zellkerngrößen der uterinen und der gastrointestinalen LMS fanden sich keine signifikanten Unterschiede.rnBezüglich der Abgrenzung zwischen uterinen LM und LMS zeigten sich signifikant höhere PCNA-Meßwerte für LMS (mittlere positive Zellkernzahl 15,08%, mittlere positive Zellkernzahl 16,67%) gegenüber LM (mittlere positive Zellkernzahl 1,95%, mittlere positive Zellkernzahl 2,02%). Zu den gastrointestinalen LMS-PCNA Messwerten gab es keinen signifikanten Unterschied (mittlere positive Zellkernfläche 19,07%, mittlere positive Zellkernzahl 16,43).rnKein signifikanter Zusammenhang zeigte sich bei der Höhe der PCNA-Meßwerte und der Prognose sowohl der uterinen als auch der gastrointestinalen LMS.rnIn dieser Studie stellten sich als signifikant prognoserelevant lediglich das Alter sowohl bei den uterinen und gastrointestinalen LMS heraus. Bei den uterinen LMS war auch noch ein schlechteres Grading und das Vorhandensein von Nekrosen signifikant mit der Prognose korreliert.rnNicht signifikant prognoserelevant waren sowohl bei den uterinen wie den gastrointestinalen LMS die Tumorgröße und die PCNA-Meßwerthöhe. Bei den gastrointestinalen Leiomyosarkomen zusätzlich noch das Vorhandensein von Nekrosen.rnEin signifikanter Zusammenhang wurde zwischen PCNA-Meßwerten und der Uterusgröße bzw. auch der Myomgröße bei den uterinen Leiomyomen sowie analog der Tumorgröße der uterinen und der gastrointestinalen LMS festgestellt. Innerhalb der Gruppe der uterinen Myome zeigten sich für zellreiche Myome zwar höhere Messwerte, die jedoch nicht signifikant waren.rnKein Zusammenhang zeigte sich dagegen für die Höhe der PNCA-Meßwerte und dem Grading der uterinen sowohl als auch der gastrointestinalen Leiomyosarkome, dem Alter der Patientinnen bei den uterinen LMS, dem Vorhandensein von Nekrosen bei den uterinen sowohl als auch bei gastrointestinalen LMS und dem Geschlecht bei den gastrointestinalen LMS.rnDie Ergebnisse stehen bezüglich der Aussage der Prognose teilweise in Widerspruch, teilweise in Einklang mit den bisherigen Veröffentlichungen. Ein großes Hemmnis ist die geringe Fallzahl, die vor allem durch die Seltenheit der Tumore bedingt ist, desweiteren die ungenügende Nachverfolgung der Patienten, die auch daraus resultiert, dass es sich um eine retrospektive Studie handelt. Hier bedarf es größerer Studien, möglicherweise als multizentrische Studien mit genauer Verlaufsbeobachtung, um auch im deutschsprachigen Raum eine weitere Erforschung dieser seltenen, umsomehr sehr interessanten und an den untersuchenden Pathologen besondere Ansprüche stellende Tumore zu geben.rn

Fish quality assessment through the application of chemico-physical, sensory and microbiological analyses

The quality of fish products is indispensably linked to the freshness of the raw material modulated by appropriate manipulation and storage conditions, specially the storage temperature after catch. The purpose of the research presented in this thesis, which was largely conducted in the context of a research project funded by Italian Ministry of Agricultural, Food and Forestry Policies (MIPAAF), concerned the evaluation of the freshness of farmed and wild fish species, in relation to different storage conditions, under ice (0°C) or at refrigeration temperature (4°C). Several specimens of different species, bogue (Boops boops), red mullet (Mullus barbatus), sea bream (Sparus aurata) and sea bass (Dicentrarchus labrax), during storage, under the different temperature conditions adopted, have been examined. The assessed control parameters were physical (texture, through the use of a dynamometer; visual quality using a computer vision system (CVS)), chemical (through footprint metabolomics 1H-NMR) and sensory (Quality Index Method (QIM). Microbiological determinations were also carried out on the species of hake (Merluccius merluccius). In general obtained results confirmed that the temperature of manipulation/conservation is a key factor in maintaining fish freshness. NMR spectroscopy showed to be able to quantify and evaluate the kinetics for unselected compounds during fish degradation, even a posteriori. This can be suitable for the development of new parameters related to quality and freshness. The development of physical methods, particularly the image analysis performed by computer vision system (CVS), for the evaluation of fish degradation, is very promising. Among CVS parameters, skin colour, presence and distribution of gill mucus, and eye shape modification evidenced a high sensibility for the estimation of fish quality loss, as a function of the adopted storage conditions. Particularly the eye concavity index detected on fish eye showed a high positive correlation with total QIM score.

Structured antibody surfaces for bio-recognition and a label-free detection of bacteria

Antibody microarrays are of great research interest because of their potential application as biosensors for high-throughput protein and pathogen screening technologies. In this active area, there is still a need for novel structures and assemblies providing insight in binding interactions such as spherical and annulus-shaped protein structures, e.g. for the utilization of curved surfaces for the enhanced protein-protein interactions and detection of antigens. Therefore, the goal of the presented work was to establish a new technique for the label-free detection of bio-molecules and bacteria on topographically structured surfaces, suitable for antibody binding.rnIn the first part of the presented thesis, the fabrication of monolayers of inverse opals with 10 μm diameter and the immobilization of antibodies on their interior surface is described. For this purpose, several established methods for the linking of antibodies to glass, including Schiff bases, EDC/S-NHS chemistry and the biotin-streptavidin affinity system, were tested. The employed methods included immunofluorescence and image analysis by phase contrast microscopy. It could be shown that these methods were not successful in terms of antibody immobilization and adjacent bacteria binding. Hence, a method based on the application of an active-ester-silane was introduced. It showed promising results but also the need for further analysis. Especially the search for alternative antibodies addressing other antigens on the exterior of bacteria will be sought-after in the future.rnAs a consequence of the ability to control antibody-functionalized surfaces, a new technique employing colloidal templating to yield large scale (~cm2) 2D arrays of antibodies against E. coli K12, eGFP and human integrin αvβ3 on a versatile useful glass surface is presented. The antibodies were swept to reside around the templating microspheres during solution drying, and physisorbed on the glass. After removing the microspheres, the formation of annuli-shaped antibody structures was observed. The preserved antibody structure and functionality is shown by binding the specific antigens and secondary antibodies. The improved detection of specific bacteria from a crude solution compared to conventional “flat” antibody surfaces and the setting up of an integrin-binding platform for targeted recognition and surface interactions of eukaryotic cells is demonstrated. The structures were investigated by atomic force, confocal and fluorescence microscopy. Operational parameters like drying time, temperature, humidity and surfactants were optimized to obtain a stable antibody structure.

Studio ed implementazione di algoritmi di stereo vision in ambito mobile: l'applicazione "SuperStereo"

L'analisi di un'immagine con strumenti automatici si è sviluppata in quella che oggi viene chiamata "computer vision", la materia di studio proveniente dal mondo informatico che si occupa, letteralmente, di "vedere oltre", di estrarre da una figura una serie di aspetti strutturali, sotto forma di dati numerici. Tra le tante aree di ricerca che ne derivano, una in particolare è dedicata alla comprensione di un dettaglio estremamente interessante, che si presta ad applicazioni di molteplici tipologie: la profondità. L'idea di poter recuperare ciò che, apparentemente, si era perso fermando una scena ed imprimendone l'istante in un piano a due dimensioni poteva sembrare, fino a non troppi anni fa, qualcosa di impossibile. Grazie alla cosiddetta "visione stereo", invece, oggi possiamo godere della "terza dimensione" in diversi ambiti, legati ad attività professionali piuttosto che di svago. Inoltre, si presta ad utilizzi ancora più interessanti quando gli strumenti possono vantare caratteristiche tecniche accessibili, come dimensioni ridotte e facilità d'uso. Proprio quest'ultimo aspetto ha catturato l'attenzione di un gruppo di lavoro, dal quale è nata l'idea di sviluppare una soluzione, chiamata "SuperStereo", capace di permettere la stereo vision usando uno strumento estremamente diffuso nel mercato tecnologico globale: uno smartphone e, più in generale, qualsiasi dispositivo mobile appartenente a questa categoria.

Airborne in situ measurements of ice particles in the tropical tropopause layer

Ice clouds have a strong effect on the Earth-atmosphere radiative energy balance, on the distribution of condensable gases in the atmosphere, as well as on the chemical composition of the air. The ice particles in these clouds can take on a variety of shapes which makes the description of the cloud microphysical properties more difficult. In the tropical upper troposphere/lower stratosphere (UTLS), a region where ice cloud abundance is relatively high, different types of ice clouds can be observed. However, in situ measurements are rare due to the high altitude of these clouds and the few available research aircraft, only three worldwide, that can fly at such altitudes.rnThis work focuses on in situ measurements of the tropical UTLS clouds performedrnwith a Cloud Imaging Probe (CIP) and a Forward Scattering Spectrometer Probern(FSSP-100), whereof the CIP is the key instrument of this thesis. The CIP is anrnairborne in situ instrument that obtains two-dimensional shadow images of cloud particles. Several cloud microphysical parameters can be derived from these measurements, e.g. number concentrations and size distributions. In order to obtain a high quality data set, a careful image analysis and several corrections need to be applied to the CIP observations. These methods are described in detail.rnMeasurements within the tropical UTLS have been performed during two campaigns:rnSCOUT-O3, 2005 in Northern Australia and SCOUT-AMMA, 2006 inWest Africa. Thernobtained data set includes first observations of subvisible cirrus clouds over a continental area and observations of the anvils of deep convective clouds. The latter can be further divided into clouds in mesoscale convective system outflows of different ages and clouds in overshooting cloud turrets that even penetrated the stratosphere. The microphysical properties of these three cloud types are discussed in detail. Furthermore, the vertical structure of the ice clouds in the UTLS is investigated. The values of the microphysical parameters were found to decrease with increasing altitude in the upper troposphere. Particle numbers and maximum sizes were also decreasing with increasing age of the outflow clouds. Further differences between the deep convective clouds and subvisible cirrus were found in the particle morphology as well as in the ratio of the observed aerosol particles to cloud particles which indicates that the different freezing processes (deposition, contact, immersion freezing) play different roles in the formation of the respective clouds. For the achievementrnof a better microphysical characterisation and description numerical fits have been adjusted onto the cloud particle size distributions of the subvisible cirrus as well as on the size distributions of the clouds at different altitudes in the UTLS.

Glukosestoffwechsel und Strahlentherapie solider, maligner Tumoren

Der Tumorstoffwechsel ist charakterisiert durch eine erhöhte Glykolyserate und die Anreicherung von Laktat auch in Anwesenheit von Sauerstoff. In früheren Arbeiten dieser Arbeitsgruppe konnte gezeigt werden, dass ein hoher Laktatgehalt in Primärtumoren signifikant mit einem gesteigerten Metastasierungsverhalten und einer schlechteren Patientenprognose verknüpft ist. Ein wichtiges Verfahren zur Bestimmung des Metabolitstatus in kryokonservierten Tumorschnitten ist die induzierte, metabolische Biolumineszenz. Im Rahmen dieser Arbeit wurde ein neues, digitales Kamerasystem für Biolumineszenzmessungen etabliert. Außerdem wurde der für die Laktat- und Glukosemessungen benötigte Enzymmix optimiert, so dass eine bessere Lichtausbeute und eine Kosteneinsparung von etwa 50% erzielt werden konnte. Durch die Einführung von Kontrollmessungen und die Verwendung eines neu entwickelten ImageJ-PlugIns für eine halbautomatisierte Auswertung, konnte ein zuverlässiges Messsystem etabliert werden, das Ergebnisse mit einer verbesserten Reproduzierbarkeit liefert. rnDieses neue Messsytem wurde in einer Studie an zehn humanen xenotransplantierten Plattenepithelkarzinomen des Kopf-Hals-Bereiches erfolgreich eingesetzt. Es konnte gezeigt werden, dass eine signifikante, positive Korrelation zwischen dem Laktatgehalt in soliden Primärtumoren und der Resistenz gegenüber einer fraktionierten Strahlentherapie besteht. rnIn einer weiterführenden Studie wurde im gleichen Xenograftmodell der Einfluss einer fraktionierten Strahlentherapie auf den Tumorstoffwechsel untersucht. Der Vergleich von zwei humanen Plattenepithelkarzinomlinien des Kopf-Hals-Bereichs im Verlauf einer fraktionierten Strahlentherapie zeigt deutliche Unterschiede zwischen strahlenresistenten und strahlensensiblen Tumoren. In der strahlenempfindlichen Tumorlinie UT-SCC 14 treten nach Bestrahlung mit drei Fraktionen in der Expression glykolyse-assoziierter Gene und nach zehn Fraktionen im ATP- und Laktatgehalt signifikante Veränderungen auf. Im Gegensatz dazu wird bei der strahlenresistenten Linie UT-SCC 5 lediglich eine Absenkung des Laktatgehaltes nach zehn Fraktionen beobachtet, nicht jedoch des ATP-Gehalts. Die mRNA-Expression wird in UT-SCC 5 nicht durch eine fraktionierte Bestrahlung verändert. Diese Ergebnisse liefern erste Hinweise, dass das mRNA-Expressionslevel und der Metabolitgehalt frühe Marker für das Ansprechen auf eine Strahlentherapie sein können.rn

Le variazioni anatomiche: La vera immagine dell'anatomia dell'uomo

La studio dell’Anatomia umana presenta una varietà di sfaccettature, che sono alla base della reale comprensione del corpo umano; ovvero la vera anatomia non è quella rappresentata nei testi ma quella che appare durante la dissezione o nelle più sofisticate analisi di immagine. Lo scopo di questa tesi è stato quello di rivisitare alcune situazioni vascolari che possono andare incontro a variazioni e cercare di comprendere, anche con l’aiuto della bibliografia, se tali variazioni possono essere causa o epifenomeni di patologie a carico delle arterie affette dalle variazioni stesse o di territori da esse dipendenti per l’afflusso sanguigno. E’ stata condotta una analisi su preparati cadaverici in particolare in tre distretti: a) addome e tripode celiaco/mesenterica superiore; b) circolo cerebrale; d) orco aortico.

Analisi d'immagine, patologia quantitativa e dimensione frattale in patologia veterinaria: Densita' e forme

Fino dagli albori della metodica scientifica, l’osservazione e la vista hanno giocato un ruolo fondamentale. La patologia è una scienza visiva, dove le forme, i colori, le interfacce e le architetture di organi, tessuti, cellule e componenti cellulari guidano l’occhio del patologo e ne indirizzano la scelta diagnostico-classificativa. L’osservazione del preparato istologico in microscopia ottica si attua mediante l’esame e la caratterizzazione di anomalie ad ingrandimenti progressivamente crescenti, a diverse scale spaziali, che partono dalla valutazione dell’assetto architettonico sovracellulare, per poi spostarsi ad investigare e descrivere le cellule e le peculiarità citomorfologiche delle stesse. A differenza di altri esami di laboratorio che sono pienamente quantificabili, l’analisi istologica è intrinsecamente soggettiva, e quindi incline ad un alto grado di variabilità nei risultati prodotti da differenti patologi. L’analisi d’immagine, l’estrazione da un’immagine digitale di contenuti utili, rappresenta una metodica oggettiva, valida e robusta ormai largamente impiegata a completamento del lavoro del patologo. Si sottolinea come l’analisi d’immagine possa essere vista come fase descrittiva quantitativa di preparati macroscopici e microscopici che poi viene seguita da una interpretazione. Nuovamente si sottolinea come questi descrittori siano oggettivi, ripetibili e riproducibili, e non soggetti a bassa concordanza inter operatore. La presente tesi si snoda attraverso un percorso concettuale orientato ad applicazioni di analisi d’immagine e patologia quantitativa che parte dalle applicazioni più elementari (densità, misure lineari), per arrivare a nozioni più avanzate, quali lo studio di complessità delle forme mediante l’analisi frattale e la quantificazione del pattern spaziale di strutture sovracellulari.

Analyse der intrazellulären Freisetzung von Wirkstoffmodellen via konfokaler Laser-Raster-Mikroskopie

In der vorliegenden Arbeit wurde gezeigt, wie man das Potential nanopartikulärer Systeme, die vorwiegend via Miniemulsion hergestellt wurden, im Hinblick auf „Drug Delivery“ ausnutzen könnte, indem ein Wirkstoffmodell auf unterschiedliche Art und Weise intrazellulär freigesetzt wurde. Dies wurde hauptsächlich mittels konfokaler Laser-Raster-Mikrokopie (CLSM) in Kombination mit dem Bildbearbeitungsprogramm Volocity® analysiert.rnPBCA-Nanokapseln eigneten sich besonders, um hydrophile Substanzen wie etwa Oligonukleotide zu verkapseln und sie so auf ihrem Transportweg in die Zellen vor einem etwaigen Abbau zu schützen. Es konnte eine Freisetzung der Oligonukleotide in den Zellen aufgrund der elektrostatischen Anziehung des mitochondrialen Membranpotentials nachgewiesen werden. Dabei war die Kombination aus Oligonukleotid und angebundenem Cyanin-Farbstoff (Cy5) an der 5‘-Position der Oligonukleotid-Sequenz ausschlaggebend. Durch quantitative Analysen mittels Volocity® konnte die vollständige Kolokalisation der freigesetzten Oligonukleotide an Mitochondrien bewiesen werden, was anhand der Kolokalisationskoeffizienten „Manders‘ Coefficients“ M1 und M2 diskutiert wurde. Es konnte ebenfalls aufgrund von FRET-Studien doppelt markierter Oligos gezeigt werden, dass die Oligonukleotide weder beim Transport noch bei der Freisetzung abgebaut wurden. Außerdem wurde aufgeklärt, dass nur der Inhalt der Nanokapseln, d. h. die Oligonukleotide, an Mitochondrien akkumulierte, das Kapselmaterial selbst jedoch in anderen intrazellulären Bereichen aufzufinden war. Eine Kombination aus Cyanin-Farbstoffen wie Cy5 mit einer Nukleotidsequenz oder einem Wirkstoff könnte also die Basis für einen gezielten Wirkstofftransport zu Mitochondrien liefern bzw. die Grundlage schaffen, eine Freisetzung aus Kapseln ins Zytoplasma zu gewährleisten.rnDer vielseitige Einsatz der Miniemulsion gestattete es, nicht nur Kapseln sondern auch Nanopartikel herzustellen, in welchen hydrophobe Substanzen im Partikelkern eingeschlossen werden konnten. Diese auf hydrophobe Wechselwirkungen beruhende „Verkapselung“ eines Wirkstoffmodells, in diesem Fall PMI, wurde bei PDLLA- bzw. PS-Nanopartikeln ausgenutzt, welche durch ein HPMA-basiertes Block-Copolymer stabilisiert wurden. Dabei konnte gezeigt werden, dass das hydrophobe Wirkstoffmodell PMI innerhalb kürzester Zeit in die Zellen freigesetzt wurde und sich in sogenannte „Lipid Droplets“ einlagerte, ohne dass die Nanopartikel selbst aufgenommen werden mussten. Daneben war ein intrazelluläres Ablösen des stabilisierenden Block-Copolymers zu verzeichnen, welches rn8 h nach Partikelaufnahme erfolgte und ebenfalls durch Analysen mittels Volocity® untermauert wurde. Dies hatte jedoch keinen Einfluss auf die eigentliche Partikelaufnahme oder die Freisetzung des Wirkstoffmodells. Ein großer Vorteil in der Verwendung des HPMA-basierten Block-Copolymers liegt darin begründet, dass auf zeitaufwendige Waschschritte wie etwa Dialyse nach der Partikelherstellung verzichtet werden konnte, da P(HPMA) ein biokompatibles Polymer ist. Auf der anderen Seite hat man aufgrund der Syntheseroute dieses Block-Copolymers vielfältige Möglichkeiten, Funktionalitäten wie etwa Fluoreszenzmarker einzubringen. Eine kovalente Anbindung eines Wirkstoffs ist ebenfalls denkbar, welcher intrazellulär z. B. aufgrund von enzymatischen Abbauprozessen langsam freigesetzt werden könnte. Somit bietet sich die Möglichkeit mit Nanopartikeln, die durch HPMA-basierte Block-Copolymere stabilisiert wurden, gleichzeitig zwei unterschiedliche Wirkstoffe in die Zellen zu bringen, wobei der eine schnell und der zweite über einen längeren Zeitraum hinweg (kontrolliert) freigesetzt werden könnte.rnNeben Nanokapseln sowie –partikeln, die durch inverse bzw. direkte Miniemulsion dargestellt wurden, sind auch Nanohydrogelpartikel untersucht worden, die sich aufgrund von Selbstorganisation eines amphiphilen Bock-Copolymers bildeten. Diese Nanohydrogelpartikel dienten der Komplexierung von siRNA und wurden hinsichtlich ihrer Anreicherung in Lysosomen untersucht. Aufgrund der Knockdown-Studien von Lutz Nuhn konnte ein Unterschied in der Knockdown-Effizienz festgestellt werden, je nach dem, ob 100 nm oder 40 nm große Nanohydrogelpartikel verwendet wurden. Es sollte festgestellt werden, ob eine größenbedingte, unterschiedlich schnelle Anreicherung dieser beiden Partikel in Lysosomen erfolgte, was die unterschiedliche Knockdown-Effizienz erklären könnte. CLSM-Studien und quantitative Kolokalisationsstudien gaben einen ersten Hinweis auf diese Größenabhängigkeit. rnBei allen verwendeten nanopartikulären Systemen konnte eine Freisetzung ihres Inhalts gezeigt werden. Somit bieten sie ein großes Potential als Wirkstoffträger für biomedizinische Anwendungen.rn

A new information fusion method for land-use classification using high resolution satellite imagery

Satellite image classification involves designing and developing efficient image classifiers. With satellite image data and image analysis methods multiplying rapidly, selecting the right mix of data sources and data analysis approaches has become critical to the generation of quality land-use maps. In this study, a new postprocessing information fusion algorithm for the extraction and representation of land-use information based on high-resolution satellite imagery is presented. This approach can produce land-use maps with sharp interregional boundaries and homogeneous regions. The proposed approach is conducted in five steps. First, a GIS layer - ATKIS data - was used to generate two coarse homogeneous regions, i.e. urban and rural areas. Second, a thematic (class) map was generated by use of a hybrid spectral classifier combining Gaussian Maximum Likelihood algorithm (GML) and ISODATA classifier. Third, a probabilistic relaxation algorithm was performed on the thematic map, resulting in a smoothed thematic map. Fourth, edge detection and edge thinning techniques were used to generate a contour map with pixel-width interclass boundaries. Fifth, the contour map was superimposed on the thematic map by use of a region-growing algorithm with the contour map and the smoothed thematic map as two constraints. For the operation of the proposed method, a software package is developed using programming language C. This software package comprises the GML algorithm, a probabilistic relaxation algorithm, TBL edge detector, an edge thresholding algorithm, a fast parallel thinning algorithm, and a region-growing information fusion algorithm. The county of Landau of the State Rheinland-Pfalz, Germany was selected as a test site. The high-resolution IRS-1C imagery was used as the principal input data.

Messa a punto di un sistema di microscopia per l'analisi quantitativa di segnali fluorescenti

L’elaborato di tesi, che rientra nell’ambito di un progetto di collaborazione tra l’equipe del laboratorio ICM “Silvio Cavalcanti”, coordinato dal professor Giordano, e il CVG (Computer Vision Group) coordinato dal professor Bevilacqua, mira alla messa a punto di un sistema di misura quantitativa di segnali fluorescenti, tramite l’elaborazione di immagini acquisite in microscopia ottica.

Predicting and monitoring cancer treatment response with diffusion-weighted MRI

An imaging biomarker that would provide for an early quantitative metric of clinical treatment response in cancer patients would provide for a paradigm shift in cancer care. Currently, nonimage based clinical outcome metrics include morphology, clinical, and laboratory parameters, however, these are obtained relatively late following treatment. Diffusion-weighted MRI (DW-MRI) holds promise for use as a cancer treatment response biomarker as it is sensitive to macromolecular and microstructural changes which can occur at the cellular level earlier than anatomical changes during therapy. Studies have shown that successful treatment of many tumor types can be detected using DW-MRI as an early increase in the apparent diffusion coefficient (ADC) values. Additionally, low pretreatment ADC values of various tumors are often predictive of better outcome. These capabilities, once validated, could provide for an important opportunity to individualize therapy thereby minimizing unnecessary systemic toxicity associated with ineffective therapies with the additional advantage of improving overall patient health care and associated costs. In this report, we provide a brief technical overview of DW-MRI acquisition protocols, quantitative image analysis approaches and review studies which have implemented DW-MRI for the purpose of early prediction of cancer treatment response.

Effect of systemic tetracycline on the degradation of tetracycline-impregnated bilayered collagen membranes: an animal study

BACKGROUND: Premature collagen membrane degradation may compromise the outcome of osseous regenerative procedures. Tetracyclines (TTCs) inhibit the catalytic activities of human metalloproteinases. Preprocedural immersion of collagen membranes in TTC and systemic administration of TTC may be possible alternatives to reduce the biodegradation of native collagen membranes. AIM: To evaluate the in vivo degradation of collagen membranes treated by combined TTC immersion and systemic administration. MATERIALS AND METHODS: Seventy-eight bilayered porcine collagen membrane disks were divided into three groups and were immersed in 0, 50, or 100 mg/mL TTC solution. Three disks, one of each of the three groups, were implanted on the calvaria of each of 26 Wistar rats. Thirteen (study group) were administered with systemic TTC (10 mg/kg), while the remaining 13 received saline injections (control group). Calvarial tissues were retrieved after 3 weeks, and histological sections were analyzed by image analysis software. RESULTS: Percentage of remaining collagen area within nonimpregnated membranes was 52.26 ± 20.67% in the study group, and 32.74 ± 13.81% in the control group. Immersion of membranes in 100 mg/mL TTC increased the amount of residual collagen to 63.46 ± 18.19% and 42.82 ± 12.99% (study and control groups, respectively). Immersion in 50 mg/mL TTC yielded maximal residual collagen values: 80.75 ± 14.86% and 59.15 ± 8.01% (study and control groups, respectively). Differences between the TTC concentrations, and between the control and the study groups were statistically significant. CONCLUSIONS: Immersion of collagen membranes in TTC solution prior to their implantation and systemic administration of TTC significantly decreased the membranes' degradation.

Delayed osteoblast differentiation and altered inflammatory response around implants placed in incisor sockets of type 2 diabetic rats

Objective: Central to the process of osseointegration is the recruitment of mesenchymal progenitor cells to the healing site, their proliferation and differentiation to bone synthesising osteoblasts. The process is under the control of pro-inflammatory cytokines and growth factors. The aim of this study was to monitor these key stages of osseointegration and the signalling milieu during bone healing around implants placed in healthy and diabetic bone. Methods: Implants were placed into the sockets of incisors extracted from the mandibles of normal Wistar and diabetic Goto-Kakizaki rats. Mandibles 1-12 weeks post-insertion of the implant were examined by histochemistry and immunocytochemistry to localise the presence of Stro-1- positive mesenchymal progenitor cells, proliferating cellular nuclear antigen proliferative cells, osteopontin and osteocalcin, macrophages, pro-inflammatory cytokines interleukin (IL)-1 , IL-6, tumour necrosis factor (TNF)- and tumour growth factor (TGF)- 1. Image analysis provided a semi-quantification of positively expressing cells. Results: Histological staining identified a delay in the formation of mineralised bone around implants placed in diabetic animals. Within the diabetic bone, the migration of Stro-1 mesenchymal cells in the healing tissue appeared to be unaffected. However, in the diabetic healing bone, the onset of cell proliferation and osteoblast differentiation were delayed and subsequently prolonged compared with normal bone. Similar patterns of change were observed in diabetic bone for the presence of IL-1 , TNF- , macrophages and TGF- 1. Conclusion: The observed alterations in the extracellular presence of pro-inflammatory cytokines, macrophages and growth factors within diabetic tissues that correlate to changes in the signalling milieu, may affect the proliferation and differentiation of mesenchymal progenitor cells in the osseointegration process. To cite this article: Colombo JS, Balani D, Sloan AJ, St Crean J, Okazaki J, Waddington RJ. Delayed osteoblast differentiation and altered inflammatory response around implants placed in incisor sockets of type 2 diabetic rats Clin. Oral Impl. Res22, 2011; 578-586 doi: 10.1111/j.1600-0501.2010.01992.x.