Desgaste de polímeros estruturais de engenharia em contato de deslizamento com cilindro metálico

Present work proposed to map and features the wear mechanisms of structural polymers of engineering derived of the sliding contact with a metallic cylindrical spindle submitted to eccentricity due to fluctuations in it is mass and geometric centers. For this it was projected and makes an experimental apparatus from balancing machine where the cylindrical counterbody was supported in two bearings and the polymeric coupon was situated in a holder with freedom of displacement along counterbody. Thus, the experimental tests were standardized using two position of the two bearings (Fixed or Free) and seven different positions along the counterbody, that permit print different conditions to the stiffness from system. Others parameters as applied normal load, sliding velocity and distance were fixed. In this investigation it was used as coupon two structural polymers of wide quotidian use, PTFE (polytetrafluroethylene) and PEEK (poly-ether-ether-ketone) and the AISI 4140 alloy steel as counterbody. Polymeric materials were characterized by thermal analysis (thermogravimetric, differential scanning calorimetry and dynamic-mechanical), hardness and rays-X diffractometry. While the metallic material was submitted at hardness, mechanical resistance tests and metallographic analysis. During the tribological tests were recorded the heating response with thermometers, yonder overall velocity vibration (VGV) and the acceleration using accelerometers. After tests the wear surface of the coupons were analyzed using a Scanning Electronic Microscopy (SEM) to morphological analysis and spectroscopy EDS to microanalysis. Moreover the roughness of the counterbody was characterized before and after the tribological tests. It was observed that the tribological response of the polymers were different in function of their distinct molecular structure. It were identified the predominant wear mechanisms in each polymer. The VGV of the PTFE was smaller than PEEK, in the condition of minimum stiffness, in function of the higher loss coefficient of that polymer. Wear rate of the PTFE was more of a magnitude order higher than PEEK. With the results was possible developed a correlation between the wear rate and parameter (E/ρ)1/2 (Young modulus, E, density, ρ), proportional at longitudinal elastic wave velocity in the material.

Estudo das propriedades termofísicas com variação da expansibilidade de compósito desenvolvido com matriz PUR-NOP e carga funcional de argilomineral

In this study were conducted experimental procedures for determination of variation of the expandability of rigid polyurethane foam (PUR) from a natural oil polyol (NOP), specifically the Castor oil plant, Ricinus communis, pure and additions of the vermiculite in phase dispersed in different percentage within a range from 0% to 20%, mass replacement. From the information acquired, were defined the parameters for production of bodies of test, plates obtained through controlled expansion, with the final volume fixed. Initially, the plates were subjected to thermal performance tests and evaluated the temperature profiles, to later be extracted samples duly prepared in accordance with the conditions required for each test. Was proceeded then the measurement of the coefficient of thermal conductivity, volumetric capacity heat and thermal diffusivity. The findings values were compared with the results obtained in the tests of thermal performance, contributing to validation of the same. Ultimately, it was investigated the influence that changes in physical-chemical structure of the material had exerted on the variation of thermophysical quantities through gas pycnometry, scanning electron microscopy (SEM) combined with energy dispersive X-ray fluorescence spectroscopy (EDXRF), infrared spectroscopy using Fourier transform (FTIR), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Based on the results obtained was possible to demonstrate that all load percentage analyzed promoted an increase in the potential expansion (PE) of the resin. In production of the plates, the composites with density near at the free expansion presented high contraction during the cure, being the of higher density adopted as definitive standard. In the thermal performance tests, the heating and cooling curves of the different composites had presented symmetry and values very close for lines of the temperature. The results obtained for the thermophysical properties of composites, showed little difference in respect of pure foam. The percentage of open pores and irregularities in the morphology of the composites were proportionate to the increment of vermiculite. In the interaction between the matrix and dispersed phase, there were no chemical transformations in the region of interface and new compounds were not generated. The composites of PUR-NOP and vermiculite presented thermal insulating properties near the foam pure and percentage significantly less plastic in its composition, to the formulation with 10% of load

Efeito de adições poliméricas na aderência de pastas de cimento a tubos metálicos após ciclagem térmica

Thermal recovery methods, especially steam injection, have been used to produce heavy oils. However, these methods imply that the metallic casing-cement sheath interface is submitted to thermal cycling. As a consequence, cracking may develop due to the thermal expansion mismatch of such materials, which allows the flow of oil and gas through the cement sheath, with environmental and economical consequences. It is therefore important to anticipate interfacial discontinuities that may arise upon Thermal recovery. The present study reports a simple alternative method to measure the shear strength of casing-sheath interfaces using pushthrough geometry, applied to polymer-containing hardened cement slurries. Polyurethane and recycled tire rubber were added to Portland-bases slurries to improve the fracture energy of intrinsically brittle cement. Samples consisting of metallic casing sections surrounded by hardened polymer-cement composites were prepared and mechanically tested. The effect of thermal cycles was investigated to simulate temperature conditions encountered in steam injection recovery. The results showed that the addition of polyurethane significantly improved the shear strength of the casing-sheath interface. The strength values obtained adding 10% BWOC of polyurethane to a Portland-base slurry more than doubled with respect to that of polyurethane-free slurries. Therefore, the use of polyurethane significantly contributes to reduce the damage caused by thermal cycling to cement sheath, improving the safety conditions of oil wells and the recovery of heavy oils

Adubação nitrogenada em cobertura no girassol irrigado nas condições de Cassilândia-MS

Nitrogen is the most required nutrient by plants for exerting important functions in the vegetable metabolism. In sunflower crop, its efficiency causes nutritional disorder, being the nutrient that most limits the yield. Besides, high doses may increase the incidence of pests and diseases, affecting the yield. Hereafter, this experiment was carried out with the aim of evaluating the response of the irrigated sunflower crop (Helianthus annuus L.) submitted to different doses of side dressing nitrogen fertilization applied uncovered nitrogen in small parts. A randomized complete block design, with four replications was used. The constituted by four doses of nitrogen (0, 20, 40, and 80 kg ha(-1)), as urea. Side dressing nitrogen fertilization provides increase in all characteristics studied, and the dose of N of maxim suitable technical efficiency to have a good yield is of 55 kg ha(-1) of N for the cultivation of the sunflower irrigated in the region of Cassilandia, Mato Grosso do Sul State.

Crescimento micelial in vitro de cinco linhagens de Agaricus bisporus submetidas a diferentes condições de temperatura

Avaliou-se o crescimento micelial in vitro das linhagens ABI-05/03, ABI-06/04, ABI-04/02, ABI-06/05 e ABI-01/01 de Agaricus bisporus em meios de cultura sólidos à base de composto. As avaliações foram realizadas por meio de medições de quatro diâmetros das colônias, a cada 48h, durante 12 dias de incubação, no escuro, a 20 e 25ºC. O delineamento experimental foi o de blocos casualizados, com uso do teste de Tukey para a comparação das médias. Co m base nos resultados obtidos, verificou-se que: o crescimento micelial de A. bisporus é influenciado pela temperatura de incubação; a temperatura de 25ºC foi mais favorável para o crescimento micelial de todas as linhagens de A. bisporus; na temperatura de 20ºC, o melhor crescimento foi obtido com as linhagens ABI-06/05 e ABI-01/01; na temperatura de 25ºC, a linhagem ABI-01/01 apresentou crescimento significativamente maior que todas as demais.

Fresamento com ar quente: uma proposta para minimizar a formação de trincas térmicas em ferramentas de metal duro

This work presents the results, analyses and conclusions about a study carried out with objective of minimizing the thermal cracks formation on cemented carbide inserts during face milling. The main focus of investigation was based on the observation that milling process is an interrupted machining process, which imposes cyclic thermal loads to the cutting tool, causing frequent stresses changes in its superficial and sub-superficial layers. These characteristics cause the formation of perpendicular cracks from cutting edge which aid the cutting tool wear, reducing its life. Several works on this subject emphasizing the thermal cyclic behavior imposed by the milling process as the main responsible for thermal cracks formation have been published. In these cases, the phenomenon appears as a consequence of the difference in temperature experienced by the cutting tool with each rotation of the cutter, usually defined as the difference between the temperatures in the cutting tool wedge at the end of the cutting and idle periods (T factor). Thus, a technique to minimize this cyclic behavior with objective of transforming the milling in an almost-continuous process in terms of temperature was proposed. In this case, a hot air stream was applied into the idle period, during the machining process. This procedure aimed to minimize the T factor. This technique was applied using three values of temperature from the hot air stream (100, 350 e 580 oC) with no cutting fluid (dry condition) and with cutting fluid mist (wet condition) using the hot air stream at 580oC. Besides, trials at room temperature were carried out. Afterwards the inserts were analyzed using a scanning electron microscope, where the quantity of thermal cracks generated in each condition, the wear and others damages was analyzed. In a general way, it was found that the heating of the idle period was positive for reducing the number of thermal cracks during face milling with cemented carbide inserts. Further, the cutting fluid mist application was effective in reducing the wear of the cutting tools.

Sobrevivência de Xanthomonas axonopodis pv. manihotis em manipueira sob condições ambientais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Perfis de distribuição volumétrica de pontas XR 11003 e TXVK-4 em diferentes condições de pulverização

Com o objetivo de avaliar a uniformidade da distribuição volumétrica e o efeito da angulação dos bicos na barra em pulverizações, foi conduzido experimento em laboratório, com dez unidades de cada uma das pontas de jato plano XR 11003 e de jato cônico vazio TXVK-4, fabricadas pela Spraying Systems Co. As pontas XR 11003 foram avaliadas, isoladamente, em mesa de prova para bicos construída conforme a Norma ISO 5682-1:1996, a 0,30; 0,40 e 0,50 m de altura, submetidas à pressão de 200 e 300 kPa e posicionadas com ângulos de 30º e 45º no sentido horário e anti-horário e na vertical; as pontas TXVK-4 foram avaliadas nas mesmas alturas, porém a 300 e 400 kPa, e somente na vertical. A distribuição média do volume coletado em cada configuração, das dez unidades de cada ponta, foi inserida num programa computacional, desenvolvido para o estudo, que permitiu a simulação do padrão de deposição de uma barra pulverizadora, com 24 bicos, com sobreposições variáveis, obtendo-se, ao final, o coeficiente de variação da sobreposição, o desvio- padrão e a média do volume aplicado. Os resultados sugerem a necessidade de ajustes no espaçamento entre bicos para a obtenção de melhor uniformidade na distribuição, principalmente quando se utiliza ângulo na barra; há menor influência da variação da altura da barra sobre a uniformidade da distribuição quando o espaçamento entre bicos é reduzido.

Cobertura da pulverização e maturação de frutos do cafeeiro com ethephon em diferentes condições operacionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Distribuição volumétrica de calda produzidas pelas pontas pulverização XR, TP e TJ sob diferentes condições operacionais

Foram avaliados os perfis de distribuição volumétrica das pontas de pulverização de jato plano Extended Range XR 8004, Teejet TP 8004 e TwinJet TJ60-8004, em mesa de teste construída segundo a norma ISO 5.682-1:1996, sendo as pontas de pulverização posicionadas a 30, 40 e 50 cm de altura da mesa coletora, submetidas à pressão de 200 e 300 kPa, e posicionadas com ângulos de 30 e 45º nos sentidos horário e anti-horário e na posição vertical (0º). As pontas TJ60-8004 foram analisadas nas mesmas alturas, porém somente na posição vertical. Avaliaram-se 10 unidades de cada tipo de ponta, instaladas isoladamente na mesa. A distribuição média do volume pulverizado, coletado nas provetas, foi inserida em programa computacional, que permitiu a simulação do perfil de distribuição de uma barra pulverizadora com 24 bicos, em espaçamentos variáveis, obtendo-se ao final o coeficiente de variação, o desvio-padrão e a média do volume. Os resultados mostraram que a uniformidade de distribuição é menos influenciada pela variação da altura da barra quando o espaçamento entre bicos é reduzido e que há necessidade de adequação do espaçamento quando se utiliza ângulo na barra pulverizadora.

Manejo químico de Eichhornia crassipes e Brachiaria subquadripara com Diquat em condições de reservatório

Este trabalho teve como objetivo avaliar a eficiência do herbicida diquat no controle de plantas de Eichhornia crassipes e Brachiaria subquadripara em condições de reservatório. As parcelas experimentais apresentavam 650 m² e foram delimitadas e posicionadas por redes de pesca nas margens do reservatório de Salto Grande, Americana-SP. Os tratamentos testados foram: herbicida diquat aplicado na formulação Reward, nas doses de 960 g i.a. ha-1 (duas aplicações de 480 g, com intervalo de 15 dias), 960 g i.a. ha-1 (aplicação única), 1.920 g i.a. ha-1 (duas aplicações de 960 g, com intervalo de 15 dias), além de uma testemunha sem aplicação do herbicida. Para monitoramento das concentrações de diquat, foram coletadas amostras de água antes da aplicação do herbicida e 1, 2, 4, 7, 14 e 28 dias após aplicação (DAA) na área experimental e na montante e jusante da barragem. A análise da eficiência do diquat foi realizada através de avaliações visuais de controle no período (1, 2, 4, 7, 14, 21 e 28 DAA do herbicida) e aos dois dias após a segunda aplicação. O herbicida diquat mostrou-se eficiente no controle das plantas de E. crassipes, independentemente da dose e do manejo de aplicação, e seu efeito sobre as plantas de B. subquadripara foi temporário.

Controle químico de plantas daninhas aquáticas em condições controladas - caixa d'água

Durante o ano de 1998 foram conduzidos quatro experimentos em Botucatu, Estado de São Paulo, Brasil, em condições de caixas d'água, com o objetivo de estudar o efeito de alguns herbicidas sobre Eicchornia crassipes, Pistia stratiotes, Thypha subulata e Salvinia molesta. Os herbicidas e doses utilizadas foram: imazapyr a 125, 250, 500, 1.000, 1.500 e 2.000 g e.a./ha; 2,4 D a 1.200 g e.a./ha; glyphosate a 3.360 g e.a./ha. Houve, ainda, uma testemunha sem aplicação de herbicidas. Os experimentos foram instalados no delineamento experimental em blocos ao acaso, com quatro repetições. As parcelas experimentais foram constituídas pelas caixas d'água com dimensões de 60x60x60 cm e colocadas a pleno sol no campo. Utilizou-se 3, 12, 25 e 60 plantas/caixa de T. subulata, P. stratiotes, E. crassipes e S. molesta, respectivamente. Os herbicidas foram aplicados com pulverizador costal a pressão constante de CO2 de 1,75 Bar, munido de barra com bicos Teejet 110.02 VS e com um consumo de calda de 200 l/ha. Foram efetuadas avaliações visuais de controle de sete em sete dias por 35 a 49 dias, dependendo da espécie. Todos os herbicidas testados foram eficientes no controle de E. crassipes e o imazapyr foi o único herbicida a promover morte total das plantas, independente da dose utilizada. Os herbicidas 2,4 D e glyphosate não foram eficientes no controle de P. stratiotes. O herbicida imazapyr foi eficiente no controle de P. stratiotes, exceto na dose de 125 g e.a./ha. Todos os herbicidas foram eficientes no controle de T. subulata, exceção ao imazapyr na dose de125 g e.a./ha. Houve rebrota de T. subulata nas parcelas aplicadas com 2,4 D. Nenhum tratamento químico foi eficiente no controle de S. molesta.

Avaliação de cultivares de arroz de terras altas sob condições de sequeiro em Cassilândia, MS

O uso de cultivares selecionadas é uma das tecnologias de mais fácil adoção pelo agricultor, pois além de incrementar a produtividade, é um dos insumos de menor custo na produção agrícola. Assim, é fundamental obter informações sobre o desempenho de novas cultivares, nas mais diversas regiões de cultivo. Objetivou-se, neste trabalho avaliar o comportamento de cultivares de arroz de terras altas (Oryza sativa L.) (BRS Aroma, BRS Bonança, BRS Colosso, BRSMG Conai, BRSMG Curinga, BRS Soberana, BRS Talento e IAC 202), sob condições de sequeiro, na região de Cassilândia, MS. O delineamento experimental foi o de blocos ao acaso, com quatro repetições. A semeadura foi realizada em 30 de novembro de 2005, no espaçamento de 0,40 m entre linhas e 70 sementes viáveis por metro. As cultivares BRS Talento, IAC 202 e BRS Soberana apresentaram comportamento superior. As cultivares BRS Soberana, BRS Bonança, BRS Colosso, IAC 202 e BRS Talento apresentaram maior rendimento de grãos inteiros. É possível obterse boa produtividade (acima de 3.000 kg ha-1), na cultura do arroz de terras altas sob condições de sequeiro no município de Cassilândia, MS, desde que sejam utilizadas cultivares adequadas.

Avaliação da eficiência de catalisadores comerciais na obtenção de biodiesel de algodão (Gossipium hisutum L.)

The increasing demand for energy and the environment consequences derived from the use of fossil energy, beyond the future scarcity of the oil that currently is the main power plant of the world, it stimulated the research around the production of biodiesel. In this work the synthesis of biodiesel of cotton in the methyl route was carried through, for had been in such a way used catalyst commercial homogeneous, Na-Methylat and the K-Methylat, aiming to the evaluation of the efficiency of them. An experimental planning 23 was elaborated aiming to evaluate the influence of the variable (molar reason oil/alcohol, % of catalyst and temperature) in the process as well as indicating the excellent point of operation in each case. The biodiesel was analyzed by gaseous chromatography, indicating a conversion of 96,79% when used Na-Methylat® as catalytic, and 95,65% when the K-Methylat® was used. Optimum result found with regard to the conversion was obtained at the following conditions: molar reason oil/alcohol (1:8), temperature of 40°C and 1% of catalyst Na-Methylat, reaching a 96,79% conversion, being, therefore, above of the established for the European norm (96.5%). The analysis of regression showed that the only significant effect for a confidence level of 95%, was of the changeable temperature. The variance analysis evidenced that the considered model is fitted quite to the experimental response, being statistically significant; however it does not serve inside for make forecasts of the intervals established for each variable. The best samples were analyzed by infra-red (IR) that identified the strong bands of axial deformation C=O of methylic ester, characterized through analyses physicochemical that had indicated conformity with the norms of the ANP, that with the thermal and rheological analyses had together evidenced that biodiesel can be used as combustible alternative in substitution to diesel

Densidades de palha e condições de luminosidade na germinação de sementes de Euhphorbia heterophylla

It was studied the influence of sugarcane straw density and light conditions on the germination of seeds of Euphorbia heterophylla under controlled conditions. The experimental design was completely randomized design with four replications of 50 seeds, and the treatments were arranged in a 6 x 5 factorial, with six amount of sugarcane straw (0, 8, 10, 12, 14 and 16 t ha(-1)) and 5 types of light (constant light, constant darkness, alternating light and dark, short red and far red). The seeds were germinated in plastic type boxes covered by overlapping layers of straw and kept in germination. Assessments of germination were daily computing the normal seedlings, when they presented protusion roots visible and calculated the germination speed index (IGS). It was observed that the increase of different densities of straw and different wave lengths provided germination ranged from 83 to 97% and IGS between 9.85 to 15.36. The different densities of straw and wavelength did not suppress the germination of E. heterophylla. Therefore, the species was insensitive to light, so the presence of raw sugarcane system can't be considered a potential tool for controlling this species.