Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Efeito da moagem de alta energia na microestrutura e nas propriedades magnéticas do compósito wc-10%p.Co

This work a studied the high energy milling effect in microstructure and magnetic properties of the WC-10wt.%Co composite. The composite powders were prepared by mechanical mixed and milled at 2 hours, 100 hours, 200 hours and 300 hours in planetary milling. After this process the composite were compacted in stainless steel die with cylindrical county of 10 mm of diameter, at pressure 200 Mpa and sintered in a resistive furnace in argon atmosphere at 1400 oC for 5 min. The sintered composite were cutted, inlaid, sandpapered, and polished. The microestrutural parameters of the composite was analyzed by X-ray diffraction, scanning electronic microscopy, optical microscopy, hardness, magnetic propriety and Rietveld method analyze. The results shows, with milling time increase the particle size decrease, it possibility minor temperature of sintering. The increase of milling time caused allotropic transformation in cobalt phase and cold welding between particles. The cold welding caused the formation of the particle composite. The X-ray diffraction pattern of composite powders shows the WC peaks intensity decrease with the milling time increase. The X-ray diffraction pattern of the composite sintered samples shows the other phases. The magnetic measurements detected a significant increase in the coercitive field and a decrease in the saturation magnetization with milling time increase. The increase coercitive field it was also verified with decrease grain size with milling time increase. For the composite powders the increase coercitive field it was verified with particle size reduction and saturation magnetization variation is relate with the variation of free cobalt. The Rietveld method analyze shows at milling time increase the mean crystalline size of WC, and Co-cfc phases in composite sintered sample are higher than in composite powders. The mean crystallite size of Co-hc phase in composite powders is higher than in composite sintered sample. The mean lattice strains of WC, Co-hc and Co-cfc phases in composite powders are higher than in composite sintered samples. The cells parameters of the composite powder decrease at milling time increase this effect came from the particle size reduction at milling time increase. In sintered composite the cells parameters is constant with milling time increase

Desenvolvimento e caracterização de filtros cerâmicos para aplicações a altas temperaturas

Ceramic filters are cellular structures that can be produced by various techniques, among which we highlight the replication method, or method of polymeric sponge. This method consists of impregnating polymeric foam with ceramic slurry, followed by heat treatment, where will occur decomposition of organic material and the sinter of the ceramic material, resulting in a ceramic whose structure is a replica of the impregnated sponge. Ceramic filters have specific properties that make this type of material very versatile, used in various technological applications such as filters for molten metals and burners, make these materials attractive candidates for high temperature applications. In this work we studied the systems Al2O3-LZSA ceramic filters processed in the laboratory, and commercial Al2O3-SiC ceramics filters, both obtained by the replica method, this work proposes the thermal and mechanical characterization. The sponge used in the processing of filters made in the laboratory was characterized by thermogravimetric analysis. The ceramic filters were characterized by compressive strength, flexural strength at high temperatures, thermal shock, permeability and physical characterization (density and porosity) and microstructural (MEV and X-rays). From the results obtained, the analysis was made of the mechanical behavior of these materials, comparing the model proposed by Gibson and Ashby model and modified the effective area and the tension adjusted, where the modified model adapted itself better to the experimental results, representing better the mechanical behavior of ceramic filters obtained by the replica method

Síntese e caracterização de TaC e óxido misto de tântalo e cobre nanoestruturados a partir do precursor oxálico de tântalo através de reações gás-sólido e sólido-sólido a baixa temperatura

The research and development of nanostructured materials have been growing significantly in the last years. These materials have properties that were significantly modified as compared to conventional materials due to the extremely small dimensions of the crystallites. The tantalum carbide (TaC) is an extremely hard material that has high hardness, high melting point, high chemical stability, good resistance to chemical attack and thermal shock and excellent resistance to oxidation and corrosion. The Compounds of Tantalum impregnated with copper also have excellent dielectric and magnetic properties. Therefore, this study aimed to obtain TaC and mixed tantalum oxide and nanostructured copper from the precursor of tris (oxalate) hydrate ammonium oxitantalato, through gas-solid reaction and solid-solid respectively at low temperature (1000 ° C) and short reaction time. The materials obtained were characterized by X-ray diffraction (XRD), Rietveld refinement, Scanning Electron Microscopy (SEM), Spectroscopy X-Ray Fluorescence (XRF), infrared spectroscopy (IR), thermogravimetric (TG), thermal analysis (DTA) and BET. Through the XRD analyses and the Reitiveld refinement of the TaC with S = 1.1584, we observed the formation of pure tantalum carbide and cubic structure with average crystallite size on the order of 12.5 nanometers. From the synthesis made of mixed oxide of tantalum and copper were formed two distinct phases: CuTa10O26 and Ta2O5, although the latter has been formed in lesser amounts

Estudo da molhabilidade de ligas de adição à base de prata sobre insertos cerâmicos para aplicação em brocas perfuração de poços de petróleo

Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Antígenos da forma amastigota de Leishmania chagasi identificados por dupla varredura da biblioteca de cDNA

Control of human visceral leishmaniasis in endemic regions is hampered in part by the lack of knowledge with respect of the role reservoirs and vector. In addition, there is not yet an understanding of how non-symptomatic subclinical infection might influence the maintenance of infection in a particular locality. Of worrisome is the limited accessibility to medical care in places with emerging drug resistance. There is still no available protective vaccine either for humans or other reservoirs. Leishmania species are protozoa that express multiple antigens which are recognized by the vertebrate immune system. Since there is not one immunodominant epitope recognized by most hosts, strategies must be developed to optimize selection of antigens for prevention and immunodiagnosis. For this reason, we generated a cDNA library from the intracellular amastigote form of Leishmania chagasi, the causative agent of South American visceral leishmaniasis. We employed a two-step expression screen of the library to systematically identify T and T-dependent B cell antigens. The first step was aimed at identifying the largest possible number of clones producing an epitope-containing polypeptide with a pool of sera from Brazilians with documented visceral leishmaniasis. After removal of clones encoding heat shock proteins, positive clones underwent a second step screen for their ability to cause proliferation and IFN-γ responses of T cells from immune mice. Six unique clones were selected from the second screen for further analysis. The clones encoded part of the coding sequence of glutamine synthetase, transitional endoplasmic reticulum ATPase, elongation factor 1γ, kinesin K-39, repetitive protein A2, and a hypothetical conserved protein. Humans naturally infected with L. chagasi mounted both cellular and antibody responses to these protein Preparations containing multiple antigens may be optimal for immunodiagnosis and protective vaccines against Leishmania

Benthic response to upwelling events off the SE Brazilian coast

The main aim of the present study was to evaluate and compare temporal responses of the benthos in 2 continental shelf areas (Cabo Frio and Ubatuba) off the SE Brazilian coast. In Cabo Frio (23 degrees S, 42 degrees W), the western boundary coastal upwelling of the South Atlantic Central Water (SACW) enhances primary productivity, potentially increasing food supply to the benthic communities via sinking of particulate organic carbon (POC). In contrast, POC fluxes in Ubatuba (23 degrees S, 45 degrees W) are expected to be comparatively lower because SACW remains subsurface. We analyzed the temporal and spatial input of phytodetritus (concentration of chlorophyll a in sediments) and the benthic microbial biomass (estimated by ATP-based carbon content in sediments). Median surface chlorophyll concentration was computed for all daily available SeaWiFS images (from 2001 and 2002) to follow chlorophyll a inputs. All parameters used to investigate benthic responses in the study areas showed consistently higher values in Cabo Frio than in Ubatuba. The results showed that benthic response to upwelling may last months, fueling the microbial communities in the Cabo Frio region.

Maternidade e sindrome do down: Um estudo sobre o sentimento vinculado frente ao diagnóstico

Trata-se de um estudo de delineamento transversal de caráter multidisciplinar, o qual conta com um estatístico que contribuiu para o delineamento do estudo, realizando o cálculo amostral e contribuindo efetivamente para análise dos dados e alunos de psicologia e pediatrias que contribuíram para a coleta de dados. A literatura aponta que a transmissão inadequada do diagnóstico da Síndrome de Down pode prejudicar o vínculo mãe-bebê e o posterior desenvolvimento da criança. Sendo assim, este estudo objetivou analisar os sentimentos maternos frente a este diagnóstico, verificando diferentes formas de transmissão e possíveis facilitadores da aceitação da Síndrome. A amostra foi constituída por 20 mães cujos filhos apresentam Síndrome de Down, na faixa etária de 0 à 03 anos e que recebem atendimento em ambulatório de um Hospital Universitário de Pediatria. Para coleta dos dados fez-se uso de um questionário, após a assinatura do Termo de Consentimento Livre e Esclarecido. Os dados foram analisados através de dois softwares de processamento de dados, o SPSS e o ALCESTE (Análise Lexical por Contexto de um Conjunto de Segmento de Texto). Os dados indicaram que 90% das mães receberam o diagnóstico de Síndrome de Down depois do parto. 75% dos diagnósticos foram comunicados pelo médico pediatra e 15% pelas enfermeiras. As mãe referiram que o diagnóstico foi tardio, inadequado e insuficiente no informativo. Observouse que as entrevistadas viveram os mesmos sentimentos observados na literatura como: choque, negação, tristeza e ira, adaptação e reorganização. Tais resultados permitem concluir que o diagnóstico de SD nas mães investigadas foi em sua maioria tardio, realidade comum no Brasil, principalmente quando se trata de classes econômicas baixas. As mães apontam que percebem este diagnóstico como tardio, inadequado e insuficiente no informativo, e gera sentimentos que a literatura já cita como comuns frente a esse tipo de diagnóstico. Portanto, observamos que a notícia pode ser um fator que dificulte ou facilite o estabelecimento do vínculo mãe-bebê, comprometendo a busca de recursos para o desenvolvimento da criança

Vertical distribution of benthic invertebrate larvae during an upwelling event along a transect off the tropical Brazilian continental margin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of hot and cold smoking processes on organoleptic properties, yield and composition of matrinxa fillet

Foi avaliado o efeito do processo de defumação a quente (45-90ºC/5 horas) e a frio (27-45ºC/10 horas) nas propriedades organolépticas, no rendimento e na composição dos filés de matrinxã (Brycon cephalus). Não houve diferença significativa no rendimento de filés defumados e não-defumados. As perdas no processo de defumação foram significativamente maiores para defumação a quente (19,37%) em comparação à defumação a frio (17,08%). O processo de defumação reduziu a umidade (in natura = 72,91%; defumado a quente = 58,51%; e defumado a frio = 59,68%) e aumentou os teores de proteína bruta, lipídios e cinzas. Houve diferença significativa somente nos teores de proteína no defumado a quente (28,07%) e defumado a frio (27,14%). O processo a frio resultou em melhor aparência e cor de filé, enquanto o processo a quente melhorou o sabor, o teor de sal e a aparência geral. O aroma e a textura não diferiram significativamente entre os processos. O processo de defumação a quente melhora as propriedades organolépticas e os níveis de proteína do filé de matrinxã.

Fatores que afetam a germinação e a emergência de Xanthium strumarim L.: dormência, qualidade da luz e profundidade de semeadura

Foram conduzidos três ensaios com o objetivo de estudar os efeitos de diferentes métodos de quebra de dormência das sementes, da qualidade da luz e da profundidade de semeadura na germinação e emergência do Xanthium strumarim L. (carrapichão). No primeiro ensaio, sob condições de câmara de crescimento, os tratamentos constaram de 5 métodos de quebra de dormência: mecânico (lixa), químico (H2SO4 conc. por 10 min.), pré-tratamento em água (imersão por 2 horas), físico (choque térmico: água à 80oC por 2 min.) e testemunha, que proporcionaram 100%, 93%, 93%, 87% e 80% de germinação, respectivamente, sem haver diferença estatística entre os mesmos. O pré-tratamento em água apresentou menor índice de velocidade de germinação (IVG) e os demais não diferiram significativamente entre si. No segundo ensaio, também sob condições de câmara de crescimento, os tratamentos de qualidade da luz constaram de 6 filtros de luz, que resultaram nas seguintes porcentagens de germinação: azul - com refletividade máxima a 450 nm (13%), verde-500 nm (33%), vermelho-700 nm (13%), vermelho/distante-760 nm (7%), ausência de luz (26%) e transparente - sem absortividade na região de 380 a 760 nm (testemunha, 73%), indicando sensibilidade das sementes à qualidade de luz. No terceiro ensaio, sob condições de casa-de-vegetação, os tratamentos foram diferentes profundidades de semeadura (0 a 20 cm, em intervalos de 2 cm), sendo que o máximo de emergência ocorreu no intervalo de 0 a 8 cm, no qual foi observado 67% de emergência do carrapichão, com maior índice de velocidade emergência (IVE), sendo que após os 16 cm, praticamente não houve emergência.

Half-sib progenies evaluation in velvet grass

O capim-lanudo (Holcus lanatus L.) possui grande potencial de utilização como pastagem de inverno nas regiões subtropicais, devido a seu bom estabelecimento, persistência, produção, resistência ao frio, palatabilidade e capacidade de afilhamento. O objetivo deste trabalho foi estimar a variabilidade genética e a herdabilidade de caracteres agronômicos e identificar progênies superiores. Foram avaliadas 60 progênies de meios-irmãos, para altura (NH) e diâmetro da planta na fase vegetativa, duração do ciclo vegetativo (ciclo), altura final (FH) e número de afilhos. Houve diferença entre progênies para todos os caracteres. As estimativas de herdabilidade foram de 38%, 32%, 92%, 57% e 64% para NH, diâmetro, ciclo, FH e afilhos, respectivamente. O maior ganho genético estimado foi de 30,77 % para o número de afilhos. Existe variabilidade para todos os caracteres e são esperados ganhos na seleção entre progênies.

Thermal and mechanical shocks affecting the first flush of production of Lentinula edodes on Eucalyptus saligna logs

O objetivo deste trabalho foi avaliar o efeito do choque térmico e mecânico na produtividade de Lentinula edodes em 140 toras de Eucalyptus saligna, completamente colonizadas pelo fungo, em diferentes tempos de imersão em água e no primeiro fluxo de produção. As toras foram imersas em água resfriada (16ºC) ou à temperatura ambiente (22ºC); os períodos de imersão corresponderam a 6, 10, 14, 18, 22, 26 e 38 horas; o choque mecânico foi acompanhado por três quedas consecutivas da tora, em posição vertical, no chão. A temperatura da água e o tempo de imersão afetaram a produção de L. edodes, resultando em aumentos significativos (2 a 4 vezes) nos tratamentos em que as toras foram submetidas à água resfriada e nos tempos de imersão mais curtos (6 e 10 horas). O choque mecânico não resultou em aumento na produção de basidiomas.