Development of an innovative non rule-based energy management strategy for a Hybrid Electric Vehicle, structured for predictive driving controls based on external information knowledge

Recently, the interest of the automotive market for hybrid vehicles has increased due to the more restrictive pollutants emissions legislation and to the necessity of decreasing the fossil fuel consumption, since such solution allows a consistent improvement of the vehicle global efficiency. The term hybridization regards the energy flow in the powertrain of a vehicle: a standard vehicle has, usually, only one energy source and one energy tank; instead, a hybrid vehicle has at least two energy sources. In most cases, the prime mover is an internal combustion engine (ICE) while the auxiliary energy source can be mechanical, electrical, pneumatic or hydraulic. It is expected from the control unit of a hybrid vehicle the use of the ICE in high efficiency working zones and to shut it down when it is more convenient, while using the EMG at partial loads and as a fast torque response during transients. However, the battery state of charge may represent a limitation for such a strategy. That’s the reason why, in most cases, energy management strategies are based on the State Of Charge, or SOC, control. Several studies have been conducted on this topic and many different approaches have been illustrated. The purpose of this dissertation is to develop an online (usable on-board) control strategy in which the operating modes are defined using an instantaneous optimization method that minimizes the equivalent fuel consumption of a hybrid electric vehicle. The equivalent fuel consumption is calculated by taking into account the total energy used by the hybrid powertrain during the propulsion phases. The first section presents the hybrid vehicles characteristics. The second chapter describes the global model, with a particular focus on the energy management strategies usable for the supervisory control of such a powertrain. The third chapter shows the performance of the implemented controller on a NEDC cycle compared with the one obtained with the original control strategy.

Effect of Pavement-Vehicle Interaction on Highway Fuel Consumption and Emission

Vehicle fuel consumption and emission are two important effectiveness measurements of sustainable transportation development. Pavement plays an essential role in goals of fuel economy improvement and greenhouse gas (GHG) emission reduction. The main objective of this dissertation study is to experimentally investigate the effect of pavement-vehicle interaction (PVI) on vehicle fuel consumption under highway driving conditions. The goal is to provide a better understanding on the role of pavement in the green transportation initiates. Four study phases are carried out. The first phase involves a preliminary field investigation to detect the fuel consumption differences between paired flexible-rigid pavement sections with repeat measurements. The second phase continues the field investigation by a more detailed and comprehensive experimental design and independently investigates the effect of pavement type on vehicle fuel consumption. The third study phase calibrates the HDM-IV fuel consumption model with data collected in the second field phase. The purpose is to understand how pavement deflection affects vehicle fuel consumption from a mechanistic approach. The last phase applies the calibrated HDM-IV model to Florida’s interstate network and estimates the total annual fuel consumption and CO2 emissions on different scenarios. The potential annual fuel savings and emission reductions are derived based on the estimation results. Statistical results from the two field studies both show fuel savings on rigid pavement compared to flexible pavement with the test conditions specified. The savings derived from the first phase are 2.50% for the passenger car at 112km/h, and 4.04% for 18-wheel tractor-trailer at 93km/h. The savings resulted from the second phase are 2.25% and 2.22% for passenger car at 93km/h and 112km/h, and 3.57% and 3.15% for the 6-wheel medium-duty truck at 89km/h and 105km/h. All savings are statistically significant at 95% Confidence Level (C.L.). From the calibrated HDM-IV model, one unit of pavement deflection (1mm) on flexible pavement can cause an excess fuel consumption by 0.234-0.311 L/100km for the passenger car and by 1.123-1.277 L/100km for the truck. The effect is more evident at lower highway speed than at higher highway speed. From the network level estimation, approximately 40 million gallons of fuel (combined gasoline and diesel) and 0.39 million tons of CO2 emission can be saved/reduced annually if all Florida’s interstate flexible pavement are converted to rigid pavement with the same roughness levels. Moreover, each 1-mile of flexible-rigid conversion can result in a reduction of 29 thousand gallons of fuel and 258 tons of CO2 emission yearly.

Participation of portuguese manufacturing industry in global value chains

Portugal’s manufacturing sector has a significant importance both in national income and employment. As has been pointed out by several researchers, the traditional methods of analysis fail to grasp all the dimensions of economic competitiveness. This dissertation is then, at its core, an analysis of Portugal’s manufacturing industry in terms of the latter’s value added to production and impact to employment under the framework of global value chains. The current dissertation seeks to study in which way the Portuguese manufacturing industry, and its respective sectors, has a direct and indirect impact on the creation of value added and employment and how this impact can be measured. For development of this work the input-output approach for calculation of multipliers and the new framework proposed by Timmer et al. (2013) for calculation of GVC income and GVC jobs indicators were used, elaborated on the basis of the WIOD project dataset. Moreover, to illustrate the application of the provided methodology the Portuguese textile industry was used as an example. It was found that the changes in final demand of such sectors as Pulp, Paper, Printing and Publishing; Machinery, Nec and Textiles and Textile Products would have a larger impact on generated value added than other manufacturing sectors. At the same time, employment created by the changes in final demand would be more impacted by such sectors as Food, Beverages and Tobacco; Wood and Products of Wood and Cork and Textiles and Textile Products. In this regard, the number of low-skilled workers in Portugal seems to be more effected by changes in final demand, than those occupied by higher -skilled individuals. Moreover, it was found that the distribution of GVC income and GVC jobs for the Portuguese manufacturing industry shares a similar outlook. However, upon closer inspection of GVC labour distribution by skill levels there seems to exist a general progression in which low-skilled jobs requirements are met by local resources, while the need for higher skilled jobs require a greater “off-shoring” of work The results obtained through calculations of presented multipliers provide a powerful tool for policy makers in strategic planning of development of national economy. Using the provided methodology and obtained results, a government and supranational organizations could define which industry would have the greatest impact for an additional unit of output generated through the economy, and thus define the sectors for further investments.

Organization and jurisdiction of the courts of South Carolina

This study is designed to give a brief presentation of the judicial structure of South Carolina without going into the matters of procedure. The text of the study describes the manner of selection of the judges and the jurisdiction of each court. The accompanying chart attempts to show the different types and levels of courts in the state system and the chain of appeals from lower to higher courts.

Effects of clouds on the surface shortwave radiation at a rural inland mid-latitude site

Seven years (2003–2010) of measured shortwave (SW) irradiances were used to obtain estimates of the 10 min averaged effective cloud optical thickness (ECOT) and of the shortwave cloud radiative effect (CRESW) at the surface in a mid-latitude site (Évora — south of Portugal), and its seasonal variability is presented. The ECOT, obtained using transmittance measurements at 415 nm, was compared with the correspondent MODIS cloud optical thickness (MODIS COT) for non-precipitating water clouds and cloud fractions higher than 0.25. This comparison showed that the ECOT represents well the cloud optical thickness over the study area. The CRESW, determined for two SW broadband ranges (300–1100 nm; 285–2800 nm), was normalized (NCRESW) and related with the obtained ECOT. A logarithmic relation between NCRESW and ECOT was found for both SW ranges, presenting lower dispersion for overcast-sky situations than for partially cloudy-sky situations. The NCRESW efficiency (NCRESW per unit of ECOT) was also related with the ECOT for overcast-sky conditions. The relation found is parameterized by a power law function showing that NCRESW efficiency decreases as the ECOT increases, approaching one for ECOT values higher than about 50.

Insights into (S)-rivastigmine inhibition of butyrylcholinesterase (BuChE): Molecular docking and saturation transfer difference NMR (STD-NMR)

Rivastigmine is a very important drug prescribed for the treatment of Alzheimer's disease (AD) symptoms. It is a dual inhibitor, in that it inhibits both acetylcholinesterase (AChE) and butyrylcholinesterase (BuChE). For our screening program on the discovery of new rivastigmine analogue hits for human butyrylcholinesterase (hBuChE) inhibition, we investigated the interaction of this inhibitor with BuChE using the complimentary approach of the biophysical method, saturation transfer difference (STD)-NMR and molecular docking. This allowed us to obtain essential information on the key binding interactions between the inhibitor and the enzyme to be used for screening of hit compounds. The main conclusions obtained from this integrated study was that the most dominant interactions were (a) H-bonding between the carbamate carbonyl of the inhibitor and the NH group of the imidazole unit of H434, (b) stacking of the aromatic unit of the inhibitor and the W82 aromatic unit in the choline binding pocket via pi-pi interactions and (c) possible CH/pi interactions between the benzylic methyl group and the N-methyl groups of the inhibitor and W82 of the enzyme.

A methodological framework to assess the carbon balance of tropical managed forests.

Background: Managed forests are a major component of tropical landscapes. Production forests as designated by national forest services cover up to 400 million ha, i.e. half of the forested area in the humid tropics. Forest management thus plays a major role in the global carbon budget, but with a lack of unified method to estimate carbon fluxes from tropical managed forests. In this study we propose a new time- and spatially-explicit methodology to estimate the above-ground carbon budget of selective logging at regional scale. Results: The yearly balance of a logging unit, i.e. the elementary management unit of a forest estate, is modelled by aggregating three sub-models encompassing (i) emissions from extracted wood, (ii) emissions from logging damage and deforested areas and (iii) carbon storage from post-logging recovery. Models are parametrised and uncertainties are propagated through a MCMC algorithm. As a case study, we used 38 years of National Forest Inventories in French Guiana, northeastern Amazonia, to estimate the above-ground carbon balance (i.e. the net carbon exchange with the atmosphere) of selectively logged forests. Over this period, the net carbon balance of selective logging in the French Guianan Permanent Forest Estate is estimated to be comprised between 0.12 and 1.33 Tg C, with a median value of 0.64 Tg C. Uncertainties over the model could be diminished by improving the accuracy of both logging damage and large woody necromass decay submodels. Conclusions: We propose an innovating carbon accounting framework relying upon basic logging statistics. This flexible tool allows carbon budget of tropical managed forests to be estimated in a wide range of tropical regions

The Effect of Eggs Shape Index on Embryo on Mortalities, Unhatched Eggs and Day Old duck Abnormalities of Selected and Control Tegal Duck

An experiment was conducted to study the effect of eggs shape index on embryo mortalities, unhatched egg and day old duck abnormalities of selected and control Tegal duck. A total of 1428 fertile eggs obtained from a selected duck group and a control group were divided in to 3 group according to their eggs shape index (ESI), i.e. small (ESI ,79 percent), medium ( ESI ,82 percent ) and large (ESI ,85 percent ). The ESI was measured as a ratio of wide and length of eggs and percentage. Three batches of incubation with 7 day interval were carried out as replicates. Parameter measured were embryo mortalities, number of unhatched eggs and number of abnormal day old duck. Candling of eggs were performed at 6, 14 and days of incubation and mortalities of embryo were detected by loup. Results of the experiment showed that lowest embryos mortalities was occurred on medium eggs (24 percent) and significantly ( p< 0,05 ) affected by eggs size. Abnormal DOD from medium eggs was significantly (p ,0,05 ) lower (13 percent ) than the small (23 percent ) and large (21 percent ) eggs. Similar trends on eggs from selected duck and control ducks. This may be due to short term of selection program and young age of the female duck (24 weeks ). These results conclude that medium eggs (ESI ,82 percent) were the best size for hatching eggs. (Animal Production 2(1): 25-32 (2000)Key word : duck , hatching eggs, selection, eggs shape index

The Effect of Turmeric (Curcuma domestica) Extract on Water Holding Capacity, Cooking Loss, pH Values and Tenderness of Broiler Chicken Meat

Abstract.  This study was aimed to determine the influences of turmeric extract supplementation on water holding capacity, cooking loss, pH value and tenderness of broiler chicken meat Data analysis was subject to completely randomized design 5 treatments namely T0, T1, T2, T3 and T4 containing non-turmeric extract, 100 mg/kgBW/day, 200 mg/kgBW/day, 300 mg/kgBW/day and 400 mg/kgBW/day, respectively. Each unit of experiment administered 3 heads with four replications. The results indicated no effect from turmeric extract supplementation on water holding capacity, cooking loss, pH value and tenderness of broiler chicken meat. The average treatments of T0, T1, T2, T3, T4 had water holding capacities of  39.86, 37.58, 36.41, 36.94, respectively; cooking losses of 26.00, 27.58, 27.57, 27.11, and 27.49%, respectively; tenderness of 1.97, 1.95, 1.63, 1.77 and 1.99 Nmm, respectively, and final Body weights of 1,618.5, 1,568, 1,692.5, 1,651.75 and 1,462 g/head, respectively. However, a highly significant influence was observed on the pH values of 6.46, 6.04, 6.21, 6.08 and 5.98. The results indicated that none of the turmeric extract supplementation increased water holding capacity, cooking losses, tenderness and body weight. Key words: broiler, cooking loss, pH values, tenderness, water holding capacity, turmeric Abstrak. Penelitian ini bertujuan untuk mengetahui pengaruh pemberian ekstrak kunyit terhadap daya ikat air, susut masak, nilai pH dan keempukan daging ayam broiler. Manfaat penelitian yaitu tersedianya informasi ilmiah tentang ekstrak kunyit terhadap danging ayam broiler. Perlakuan yang diterapkan adalah T0 tanpa ekstrak kunyit, T1 100, T2 200, T3 300, dan T4 400 mg/kgBB/hari. Data analisis yang digunakan adalah rancangan acak lengkap yang terdiri dari 5 perlakuan dan 4 replikasi. Setiap unit percobaan terdiri dari 3 ekor. Hasil penelitian menunjukkan tidak ada pengaruh pemberian ekstrak kunyit terhadap daya ikat air, susut masak, dan keempukan daging ayam broiler. Rataan untuk perlakuan T0, T1, T2, T3, T4 pada Daya Ikat Air masing–masing 39,86; 37,58; 36,41; 36,94; 34,78%; susut masak 26,00; 27,58; 27,57; 27,11; 27,49%, keempukan 1,97; 1,95; 1,63; 1,77; 1,99 Nmm, dan bobot badan akhir 1.618,5; 1.568; 1.692,5; 1.651,75; 1.462g/ekor. Namun, memberikan pengaruh sangat nyata pada nilai pH 6,46; 6,04; 6,21; 6,08; 5,98. Hasil  menunjukkan bahwa pemberian ekstrak kunyit  tidak meningkatkan daya ikat air, susut masak, keempukan dan bobot badan. Kata Kunci : Broiler, Susut Masak, pH, Keempukan, Daya Ikat Air, Kunyit

An activity theory framework for industrial design

Ethnography has gained wide acceptance in the industrial design profession and curriculum as a means of understanding the user. However, there is considerable confusion about the particularities of its practice accompanied by the absence of an interoperable vocabulary. The consequent interdisciplinary effort is a power play between disciplines whereby the methodological view of ethnography marginalises its theoretical and analytical components. In doing so, it restricts the potential of ethnography suggesting the need for alternative methods of informing the design process. This article suggests that activity theory, with an emphasis on human activity as the fundamental unit of study, is an appropriate methodology for the generation of user requirements. The process is illustrated through the adaptation of an ethnographic case study, for the design of classroom furniture in India.

Trip to Sunshine Coast Queensland, September 2004 visit to bridge and foreshore

A trip was undertaken to look at concerns of Public Works and Main Roads Departments of Queensland. David Paterson and Wayne Ganther from CSIRO travelled to the Sunshine Coast with Alan Carse of Queensland Department of Main Roads and Michael Ball of Queensland Department of Public Works. We were also joined for part of the visits by Ed Bowers of QBuild which is a commercial unit of Public Works responsible for maintenance of Public Works. During the trip we visited a bridge on the David Low Way at Sunrise Beach near Noosa. This bridge was in a serve marine environment with high salt content in the concrete and corrosion of the galvanised guardrails and barriers. Also the foreshore at Coolum was visited and the use of stainless steel was examined. This is discussed in this report. Most problems stemmed from incorrect specification due to lack of awareness of the severity of the environment. The companion report Visit to Schools Report 2002-059-B No 7. covers the visit to four schools north of Caloundra.

Real world contexts in PISA science : implications for context-based science education

The PISA assessment instruments for students’ scientific literacy in 2000, 2003 and 2006 have each consisted of units made up of a real world context involving Science and Technology, about which students are asked a number of cognitive and affective questions. This paper discusses a number of issues from this use of S&T contexts in PISA and the implications they have for the current renewed interest in context-based science education. Suitably chosen contexts can engage both boys and girls. Secondary analyses of the students’ responses using the contextual sets of items as the unit of analysis provides new information about the levels of performance in PISA 2006 Science. .Embedding affective items in the achievement test did not lead to gender/context interactions of significance, and context interactions were less than competency ones. A number of implications for context-based science teaching and learning are outlined and the PISA 2006 Science test is suggested as a model for its assessment.

Developing a best practice framework for implementing public private partnerships (PPP) in Hong Kong

Public Private Partnership (PPP) is a well established methodology for procuring public works projects. By incorporating the private sector’s expertise, efficiency, innovation, business sense, risk sharing, financing etc. into public works projects, the quality of public services and facilities can be uplifted. Like many jurisdictions, Hong Kong is also keen to take aboard this methodology which is so familiar but yet so distant. Although they have been one of the first jurisdictions to utilise the private sector in public works projects, their comfortable financial reserves has meant that there has been no urge to push the movement until recently. PPP has become increasingly popular amongst governments. The Hong Kong Special Administrative Region (HKSAR) government is no exception. Some of the more active works departments have commissioned studies to investigate the best ways to deliver these projects, others have even trialed the method themselves. The efficiency Unit of the HKSAR government has also become an active arm in conducting research in this area. Although so, the information that is currently available is still very broad. Building from their works there is a need to develop a best practice framework for implementing PPP projects in Hong Kong by incorporating international experiences. To develop a best practice framework will require thorough investigation into the benefits, difficulties and critical success factor of PPP. PPP should also be compared with other procurement methods. In order to do so it is important to clearly understand the local situation by an analysis of projects conducted to date. Lessons learnt can further be derived from other countries and incorporated to those derived locally. Finally the best conditions in terms of project nature, complexity, types, and scales for adopting PPP should be derived. The aim and objectives of this study were achieved via a comprehensive literature review, in-depth case analyses, interview survey with experts from both Hong Kong and overseas, and finally a large scale data collection was conducted via a questionnaire survey with PPP practitioners. These findings were further triangulated before they were used as the basis to form the best practice framework presented in this thesis. The framework was then further validated by PPP experts to ensure it is comprehensive, objective, reliable and practical. This study has presented a methodology that can be adopted for future studies. It has also updated our knowledge on the development trends of PPP as well as opened up the experiences of other jurisdictions. The findings have shown that the local industry is familiar with “what” should be done in PPP projects but they are unsure of “how” these goals can be achieved. This framework has allowed this further knowledge to be delivered to PPP practitioners. As a result, the development of this framework can help to resolve the current economic crisis by encouraging more developments and business opportunities for the private sector. In addition, the correct projects can be delivered by PPP, the advantages of PPP can be maximised, and the general public can benefit from the private sector’s participation.

Protein complementation assay as a display system for screening protein libraries in the intracellular environment

A wide range of screening strategies have been employed to isolate antibodies and other proteins with specific attributes, including binding affinity, specificity, stability and improved expression. However, there remains no high-throughput system to screen for target-binding proteins in a mammalian, intracellular environment. Such a system would allow binding reagents to be isolated against intracellular clinical targets such as cell signalling proteins associated with tumour formation (p53, ras, cyclin E), proteins associated with neurodegenerative disorders (huntingtin, betaamyloid precursor protein), and various proteins crucial to viral replication (e.g. HIV-1 proteins such as Tat, Rev and Vif-1), which are difficult to screen by phage, ribosome or cell-surface display. This study used the β-lactamase protein complementation assay (PCA) as the display and selection component of a system for screening a protein library in the cytoplasm of HEK 293T cells. The colicin E7 (ColE7) and Immunity protein 7 (Imm7) *Escherichia coli* proteins were used as model interaction partners for developing the system. These proteins drove effective β-lactamase complementation, resulting in a signal-to-noise ratio (9:1 – 13:1) comparable to that of other β-lactamase PCAs described in the literature. The model Imm7-ColE7 interaction was then used to validate protocols for library screening. Single positive cells that harboured the Imm7 and ColE7 binding partners were identified and isolated using flow cytometric cell sorting in combination with the fluorescent β-lactamase substrate, CCF2/AM. A single-cell PCR was then used to amplify the Imm7 coding sequence directly from each sorted cell. With the screening system validated, it was then used to screen a protein library based the Imm7 scaffold against a proof-of-principle target. The wild-type Imm7 sequence, as well as mutants with wild-type residues in the ColE7- binding loop were enriched from the library after a single round of selection, which is consistent with other eukaryotic screening systems such as yeast and mammalian cell-surface display. In summary, this thesis describes a new technology for screening protein libraries in a mammalian, intracellular environment. This system has the potential to complement existing screening technologies by allowing access to intracellular proteins and expanding the range of targets available to the pharmaceutical industry.

Elective foot and ankle surgery : activity and perioperative complications in Queensland public hospitals, Australia

Objective: To conduct an audit of elective foot and ankle surgery in Queensland public hospitals and to compare the frequency of these procedures performed to other states and territories of Australia. ---------- Methods: ICD-10-AM data was used to extract elective foot and ankle procedures from the Data Services Unit of Queensland Health, and the Australian Institute of Health and Welfare between the years of 2000 and 2004. ---------- Results During the 4-year audit period 3846 primary procedures were performed during the 4-year period with a complication rate of 2.2% during the hospital admission period. Mean length of stay was 1.7 days. Post-operative infection rates were 0.26%. With the exception of Tasmania and the Northern Territory, Queensland performs the least number of elective foot and ankle procedures per capita per year in Australia. ---------- Conclusions This is the first reported audit of elective foot and ankle surgery for Queensland public hospitals. Complication rates cannot be directly compared to the literature as this data could only capture complications within hospital admission period. Fewer elective foot and ankle procedures were performed in Queensland public hospitals compared to all other mainland states of Australia during the data collection period.